ER10G

MCC Features • • • • ER10A
  omponents 21201 Itasca Street Chatsworth    !"# $ %    !"# THRU ER10G 10 Amp Super Fast Recovery Rectifier 50 to 400 Volts High Surge Capability Low Forward Voltage Drop High Current Capability Super Fast Switching Speed For High Efficiency • Operating Temperature: -55° to +150° C C • Storage Temperature: -55° to +150° C C MCC Part Number ER10A ER10B ER10D ER10G Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V Maximum RMS Voltage 35V 70V 140V 280V Maximum DC Blocking Voltage 50V 100V 200V 400V Maximum Ratings DO-214AB (SMCJ) (Round Lead) H Cathode Band J A Electrical Characteristics @ 25° Unless Otherwise Specified C Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time ER10A-ER10D ER10G IF(AV) IFSM 10 A 200A TA = 55° C 8.3ms, half sine DIM A B C D E F G H J C E F G D B DIMENSIONS INCHES MIN .200 .177 .002 --.053 .168 .320 .239 .234 MAX .214 .203 .005 .02 .067 .179 .330 .243 .240 MM MIN 5.08 4.70 .05 --1.35 4.27 8.13 6.08 5.95 MAX 5.43 5.30 .13 .51 1.70 4.55 8.38 6.18 6.10 NOTE VF 1.0V IFM = 10.0A; C TA = 2 5 ° TA = 25° C IR 10.0µA SUGGESTED SOLDER PAD LAYOUT Tr r 35ns 60ns I F=0.5A, IR =1.0A, Ir r =0.25A 0.190 *Pulse Test: Pulse Width 300µsec, Duty Cycle 1% 0.200” 0.070” www.mccsemi.com MCC ER10A thru ER10G Figure 1 Typical Forward Characteristics 20 10 6 4 2 Amps 1 .6 .4 .2 .1 .06 .04 .02 .01 .6 .8 1.0 Volts Instantaneous Forward Current - Amperes versus Instantaneous Forward Voltage - Volts 1.2 1.4 1.6 0 2 Single Phase, Half Wave 60Hz Resistive or Inductive Load 0 50 75 100 ° C 125 150 175 Amps 12 Figure 2 Forward Derating Curve 10 25° C 8 6 4 Figure 3 Junction Capacitance 100 60 40 20 pF 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 T J =25° C Junction Capacitance - pF versus Reverse Voltage - Volts www.mccsemi.com MCC ER10A thru ER10G Figure 4 Peak Forward Surge Current 200 175 150 125 Amps 100 50 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 25Vdc Pulse Generator Note 2 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com