ER1A_11

Micro Commercial Components
































MCC TM
  omponents 20736 Marilla Street Chatsworth    !"# $ %    !"# ER1A THRU ER1M 1 Amp Ultra Fast Recovery Silicon Rectifier 50 to 1000 Volts DO-214AA (HSMB) (Round Lead) H Cathode Band Features










• • • • •

L
ead Free









Compliant.
Finish/Rohs Compliant (Note1) ("P"Suffix designates






See ordering information)











• Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 Easy Pick And Place High Temp Soldering: 260 °C for 10 Seconds At Terminals Ultrafast Recovery Times For High Efficiency Operating Temperature(Tj): -50 °C to +150°C Storage Temperature(Tstg): -50°C to +150°C Maximum Thermal Resistance; 15 °C/W Junction To Lead MCC Device Maximum Maximum Maximum Catalog Marking Recurrent RMS DC Number Peak Reverse Voltage Blocking Voltage Voltage ER1A ER1A 50V 35V 50V ER1B ER1B 100V 70V 100V ER1C ER1C 150V 105V 150V ER1D ER1D 200V 140V 200V ER1G ER1G 400V 280V 400V ER1J ER1J 600V 420V 600V ER1K ER1K 800V 560V 800V ER1M ER1M 1000V 700V 1000V Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage IF(AV) IFSM 1.0A 30A TJ = 75°C 8.3ms, half sine DIM A B C D E F G H J Maximum Ratings • • • J A C E F G D B Electrical Characteristics @ 25°C Unless Otherwise Specified INCHES MIN .078 .075 .002 ----.035 .065 .205 .160 .130 MAX .116 .089 .008 .02 .055 .091 .224 .180 .155 DIMENSIONS MM MIN 1.98 1.90 .05 ----.90 1.65 5.21 4.06 3.30 MAX 2.95 2.25 .20 .51 1.40 2.32 5.69 4.57 3.94 NOTE ER1A-D ER1G-K ER1M VF .975V 1.35V 1.60V IFM = 1.0A; TJ = 25°C* TJ = 25°C TJ = 100°C Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time SUGGESTED SOLDER PAD LAYOUT 0.090" IR 5µA 100µA 0.085” ER1A-D ER1G-K ER1M Trr CJ 50ns 60ns 100ns Typical Junction Capacitance Note: 45pF IF=0.5A, IR=1.0A, Irr=0.25A Measured at 1.0MHz, VR=4.0V 0.070” *Pulse test: Pulse width 200 µsec, Duty cycle 2% 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. Revision: A www.mccsemi.com 1 of 4 2011/01/01 ER1A thru ER1M Figure 1 Typical Forward Characteristics 2.4 2.2 2.0 ER1A~ER1D ER1G~ER1K MCC TM Micro Commercial Components Figure 2 Forward Derating Curve 50 INSTANTANEOUS FORWARD CURRENT,(A) 10 3.0 1.0 1.8 1.6 1.4 ER1M 1.2 Amps 1.0 .8 .6 .4 Single Phase, Half Wave .2 60Hz Resistive or Inductive Load 0 0 25 50 75 °C Average Forward Rectified Current - Amperes versus Ambient Temperature - °C 100 125 150 Tj=25 C Pulse Width 300us 1% Duty Cycle 0.1 .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE,(V) Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 TJ=25°C;f=1MHZ Junction Capacitance - pFversus Reverse Voltage - Volts Revision: A www.mccsemi.com 2 of 4 2011/01/01 ER1A thru ER1M Figure 4 Peak Forward Surge Current 30 25 20 15 Amps 10 5 0 1 2 4 6 8 10 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles 20 40 60 80 100 MCC TM Micro Commercial Components Figure 5 New SMB Assembly Round Lead Process Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 25Vdc Pulse Generator Note 2 1Ω Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Revision: A www.mccsemi.com 3 of 4 2011/01/01 MCC TM Micro Commercial Components Ordering Information : Device Part Number-TP Packing Tape&Reel: 3Kpcs/Reel ***IMPORTANT NOTICE* ** Micro Comme rcial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Comme rcial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Co mponents Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from A uthorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC' s quality standards for handling and storage. MCC will not pro vide any warranty coverage or o ther assistance for parts bought from Unau thorized Source s. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. www.mccsemi.com Revision: A 4 of 4 2011/01/01