ER3B-HT

MCC TM Micro Commercial Components
  omponents 20736 Marilla Street Chatsworth    !"# $ %    !"# ER3A-HT THRU ER3M-HT • • • • Features Low forward voltage drop High current capability High reliability High surge current capability 3.0 Amp High Efficient Rectifiers 50 to 1000 Volts Maximum Ratings • • Operating Temperature: -55℃ to +125℃ Storage Temperature: -55℃ to +150℃ MCC Part Number ER3A-HT ER3B-HT ER3D-HT ER3G-HT ER3J-HT ER3K-HT ER3M-HT Device Marking ER3A ER3B ER3D ER3G ER3J ER3K ER3M Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V 600V 800V 1000V Maximum RMS Voltage 35V 70V 140V 280V 420V 560V 700V Maximum DC Blocking Voltage 50V 100V 200V 400V 600V 800V 1000V DO-214AB (SMCJ) (Round Lead) H Cathode Band J A C E Electrical Characteristics @ 25℃ Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage ER3A-HT~ER3D-HT ER3G-HT ER3J-HT~ER3M-HT F G D B IF(AV) IFSM 3.0A 150A TA = 55℃ 8.3ms, half sine DIM A B C D E F G H J DIMENSIONS INCHES MIN .200 .177 .002 --.047 .168 .309 .239 .234 MAX .214 .203 .005 .02 .056 .179 .322 .243 .240 MM MIN 5.08 4.70 .05 --1.20 4.27 7.85 6.08 5.95 MAX 5.43 5.30 .13 .51 1.42 4.55 8.18 6.18 6.10 NOTE VF 1.0V 1.3V 1.7V 10uA 200uA 50ns 75ns IFM = 3.0A; TA = 25℃ Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time ER3A-HT~ER3G-HT ER3J-HT~ER3M-HT SUGGESTED SOLDER PAD LAYOUT IR TA = 25℃ TA = 100℃ IF=0.5A, IR=1.0A IRR=0.25A Measured at 1.0MHz, VR=4.0V 0.200” 0.190 Trr Typical Junction Capacitance ER3A-HT~ER3G-HT ER3J-HT~ER3M-HT 80pF 50pF *Pulse Test: Pulse Width 300 µsec, Duty Cycle 1% CJ 0.070” www.mccsemi.com Revision: 1 2005/08/31 ER3A-HT THRU ER3M-HT RATINGS AND CHARACTERISTIC CURVES FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM AVERAGE FORWARD CURRENT. (A) 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A DUT (-) PULSE GENERATOR (NOTE 2) OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr MCC TM Micro Commercial Components FIG.2- MAXIMUM AVERAGE FORWARD CURRENT DERATING 6 5 4 3 2 1 25 50 75 100 125 150 175 O (+) 50Vdc (approx) (-) 1W NON INDUCTIVE Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm AMBIENT TEMPERATURE. ( C) FIG.3- TYPICAL REVERSE CHARACTERISTICS 1000 FIG.5- TYPICAL FORWARD CHARACTERISTICS 100.0 INSTANTANEOUS FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) ER 3A -H 1.0 .1 .01 .2 .4 .6 .8 1.0 FORWARD VOLTAGE. (V) 10 Tj=25 0C 1.0 0.1 20 40 60 80 100 120 ER ER 3G 3J -H -H T~ T ER 3M -H T 1.2 T~ ER 100 10.0 3D Tj=100 0C Tj=25 0C -H T 1.4 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 300 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT FIG.6- TYPICAL JUNCTION CAPACITANCE 175 150 125 100 75 50 25 ER ER 3A -HT PEAK FORWARD SURGE CURRENT. (A) 200 JUNCTION CAPACITANCE.(pF) 3J- ~E HT R3 ~E G- 100 R3 HT M- HT 0 1 10 100 1000 0 .1 .5 1 2 5 10 20 50 100 200 500 NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE. (V) www.mccsemi.com Revision: 1 2005/08/31