ES2D

MCC
  omponents 21201 Itasca Street Chatsworth    !"# $ %    !"# ES2A THRU ES2M 2 Amp Super Fast Recovery Silicon Rectifier 50 to 1000 Volts DO-214AC (SMAJ) (High Profile) H Cathode Band • • • • •







Features














F
or





Mount Applications
Surface

Extremely Low Thermal Resistance Easy Pick And Place High Temp Soldering: 250 °C for 10 Seconds At Terminals Superfast Recovery Times For High Efficiency • • • Maximum Ratings Operating Temperature: -50°C to +150°C Storage Temperature: -50°C to +150°C Maximum Thermal Resistance; 20°C/W Junction To Lead MCC Device Maximum Maximum Maximum Catalog Marking Recurrent RMS DC Number Peak Reverse Voltage Blocking Voltage Voltage ES2A ES2A 50V 35V 50V ES2B ES2B 100V 70V 100V ES2C ES2C 150V 105V 150V ES2D ES2D 200V 140V 200V ES2G ES2G 400V 280V 400V ES2J ES2J 600V 420V 600V ES2K ES2K 800V 560V 800V ES2M ES2M 1000V 700V 1000V IF(AV) IFSM 2.0A 50A TJ = 75°C 8.3ms, half sine DIM A B C D E F G H J J A C E F G D B Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 DIMENSIONS MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 ES2A-D ES2G-K ES2M VF .975V 1.35V 1.60V MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 NOTE IFM = 2.0A; TJ = 25°C* TJ = 25°C TJ = 100°C Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time SUGGESTED SOLDER PAD LAYOUT 0.090” IR 5µA 150µA 0.085” ES2A-D ES2G-K ES2M Trr CJ 50ns 60ns 100ns Typical Junction Capacitance 25pF IF=0.5A, IR=1.0A, Irr=0.25A Measured at 1.0MHz, VR=4.0V 0.070” *Pulse test: Pulse width 200 µsec, Duty cycle 2% www.mccsemi.com ES2A thru ES2M Figure 1 Typical Forward Characteristics 20 10 6 4 2 Amps 1 .6 .4 .2 .1 .06 .04 .02 .01 .2 .4 .6 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts .8 1.0 1.2 Amps 2.4 2.2 2.0 1.8 25°C 1.6 1.4 1.2 1.0 .8 .6 .4 Figure 2 Forward Derating Curve MCC Single Phase, Half Wave .2 60Hz Resistive or Inductive Load 0 0 25 50 75 °C Average Forward Rectified Current - Amperes ersus v Ambient Temperature - °C 100 125 150 Figure 3 Junction Capacitance 100 60 40 20 pF 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 TJ=25°C Junction Capacitance - pFversus Reverse Voltage - Volts www.mccsemi.com ES2A thru ES2M Figure 4 Peak Forward Surge Current MCC Figure 5 New SMB Assembly 50 40 30 Amps 20 10 0 1 4 6 8 10 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles 20 40 60 80 100 Round Lead Process 2 Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 25Vdc Pulse Generator Note 2 1Ω Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive www.mccsemi.com