PB62F

MCC Micro Commercial Components TM
  omponents 20736 Marilla Street Chatsworth    !"# $ %  "  !"#  PB62F Features • • • • Low Forward Voltage Any Mounting Position Silver Plated Copper Leads Surge Overload Rating Of 150 Amps 6 Amp Fast Recovery Bridge Rectifier 200 Volts PB-6 B Maximum Ratings • • Operating Temperature: -55 °C to +125°C Storage Temperature: -55°C to +150°C Device Marking Maximum Recurrent Peak Reverse Voltage 200V Maximum RMS Voltage 140V Maximum DC Blocking Voltage 200V Microsemi Catalog Number PB62F C PB62F E D Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Forward Voltage Drop Per Element Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time PB62F IF(AV) IFSM 6.0A 150A TJ = 50°C 8.3ms, half sine G + AC A AC - VF 1.30V IFM = 3.0A; TJ = 25°C* TJ = 25°C TJ = 100°C DIM A B C D E G INCHES MIN .578 .230 .750 .405 .038 .145 MAX .618 .270 --.444 .042 --A IR 10µA 1 mA DIMENSIONS MM MIN 14.69 5.84 19.10 10.30 0.97 3.70 Trr 200ns IF=0.5A, IR=1.0A, Irr=0.25A *Pulse test: Pulse width 300 µsec, Duty cycle 1% MAX 15.71 6.86 --11.30 1.07 --- NOTE 2PL 2PL 4PL/TYP ∅ Revision: 3 www.mccsemi.com 2003/04/30 PB62F Figure 1 Typical Forward Characteristics 100 60 40 20 10 6 4 2 25°C Amps 1 .6 .4 .2 .1 .06 .04 .02 .01 .2 .4 .6 .8 1.0 1.1 1.2 10 6 4 2 1 .6 .4 .2 TJ=25°C µ Amps .1 .06 .04 .02 .01 .006 .00 4 .002 .001 20 40 60 MCC TM Micro Commercial Components Figure 2 Typical Reverse Characteristics 80 Volts 100 120 140 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Forward Derating Curve 12 Instantaneous Reverse Leakage Current - MicroAmperes ersus I v Percent Of Rated Peak Reverse Voltage - Volts 10 8 6 Amps 4 2 Single Phase, Half Wave 60Hz Resistive or Inductive Load 0 0 20 40 60 °C Average Forward Rectified Current - Amperes ersus v Ambient Temperature - °C 80 100 120 Revision: 3 www.mccsemi.com 2003/04/30 PB62F Figure 4 Peak Forward Surge Current 300 250 200 150 Amps 100 50 0 MCC Micro Commercial Components TM 1 2 4 6 8 10 Cycles 20 40 00 60 80 100 Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 25Vdc Pulse Generator Note 2 1Ω Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Revision: 3 www.mccsemi.com 2003/04/30