RL104GP

MCC TM Micro Commercial Components
  omponents 20736 Marilla Street Chatsworth    !"# $ %    !"# RL101GP THRU RL107GP 1 Amp Rectifier 50 - 1000 Volts Features • • • • • • Low Current Leakage Metalurgically Bonded Construction Low Cost Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates Compliant. See ordering information) Maximum Ratings • • • Operating Temperature: -55 °C to +150°C Storage Temperature: -55°C to +150°C Maximum Thermal Resistance; 50 °C/W Junction To Lead MCC Catalog Number Device Marking Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V 600V 800V 1000V Maximum RMS Voltage Maximum DC Blocking Voltage 50V 100V 200V 400V 600V 800V 1000V D A-405 RL101GP RL102GP RL103GP RL104GP RL105GP RL106GP RL107GP RL101 RL102 RL103 RL104 RL105 RL106 RL107 35V 70V 140V 280V 420V 560V 700V A Cathode Mark B D Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward IF(AV) 1.0A TA = 75°C Current Peak Forward Surge IFSM 30A 8.3ms, half sine Current Maximum VF 1.1V IFM = 1.0A; Instantaneous Forward Voltage TJ = 25°C* Maximum DC Reverse Current At IR 5.0µA TJ = 25°C Rated DC Blocking 50µA TJ = 125°C Voltage Typical Junction CJ 15pF Measured at Capacitance 1.0MHz, VR=4.0V *Pulse test: Pulse width 300 µsec, Duty cycle 2% Note: 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. C DIMENSIONS INCHES MIN .166 .080 --1.000 MM MIN 4.10 2.00 --25.40 DIM A B C D MAX .205 .107 .024 --- MAX 5.20 2.70 .60 --- NOTE Revision: A www.mccsemi.com 1 of 5 2011/01/01 RL101GP thru RL107GP Figure 1 Typical Forward Characteristics 20 10 6 4 2 Amps 1 .6 .4 .2 25°C .1 .06 .04 .02 .01 .4 .6 .8 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts 1.0 1.2 1.4 0 .2 Amps .4 .8 1.2 MCC TM Micro Commercial Components Figure 2 Forward Derating Curve 1.0 .6 Single Phase, Half Wave 60Hz Resistive or Inductive Load 0 50 75 100 °C Average Forward Rectified Current - Amperes ersus v Ambient Temperature - °C 125 150 175 Figure 3 Junction Capacitance 100 60 40 20 pF 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 TJ=25°C Junction Capacitance - pFversus Reverse Voltage - Volts Revision: A www.mccsemi.com 2 of 5 2011/01/01 RL101GP thru RL107GP Figure 4 Typical Reverse Characteristics 100 60 40 20 10 6 4 T =100°C A 2 µAmps 1 .6 .4 .2 .1 .06 .04 .02 .01 20 40 60 80 Volts Instantaneous Reverse Leakage Current - MicroAmperes ersus v Percent Of Rated Peak Reverse Voltage - Volts 100 120 140 TA=25°C Amps 60 50 40 30 20 10 0 1 2 4 6 MCC Figure 5 Peak Forward Surge Current TM Micro Commercial Components 8 10 Cycles 20 40 60 80 100 Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Revision: A www.mccsemi.com 3 of 5 2011/01/01 MCC Micro Commercial Components TM RADIAL TAPING SPECIFICATIONS FOR RECTIFIERS A-405 Outline Only C B S F D G H A E N M T P J K DIMENSIONS INCHES MIN MAX .709 .748 .460 .540 --.106 --.205 .610 .650 --.354 --.177 .177 .217 .124 .179 .146 .169 .677 .748 .343 .384 .021 .025 --±.079 .016 .031 MM MIN 18.0 11.7 ----15.5 ----4.5 3.15 3.7 17.2 8.70 .54 --.4 MAX 20.0 13.7 2.7 5.2 16.5 9.0 4.5 5.5 4.55 4.3 19.0 9.75 .64 ±2.0 .8 NOTE PACKING METHODS P/N EXAMPLE: A=N:PANASERT ABC B = 0: NON INSULATION COATING--LEAD FIRST OUT. 1: INSULATION COATING--LEAD FIRST OUT. 2: NON INSULATION COATING--BODY FIRST OUT. 3: INSULATION COATING--BODY FIRST OUT. C = 1: FOR CATHODE DOWN, IN BULK. 2: FOR CATHODE UP, IN BULK. 3: FOR CATHODE DOWN, IN REEL. 4: FOR CATHODE UP, IN REEL DIM A B C D E F G H J K M N P S T www.mccsemi.com Revision: A 4 of 5 2011/01/01 MCC Micro Commercial Components TM Ordering Information : Device Part Number-TP Packing Tape&Reel: 5Kpcs/Reel ***IMPORTANT NOTICE* ** Micro Comme rcial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Comme rcial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Co mponents Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from A uthorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC' s quality standards for handling and storage. MCC will not pro vide any warranty coverage or o ther assistance for parts bought from Unau thorized Source s. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. www.mccsemi.com Revision: A 5 of 5 2011/01/01