SK220-L

MCC Micro Commercial Components TM
  omponents 20736 Marilla Street Chatsworth    !"# $ %    !"# S K 2 2 -L THRU S K 2 2 0 -L 2 Amp Schottky Rectifier 20 to 200 Volts DO-214AA (SMB) (LEAD FRAME) A Features • • • • • • • Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates Compliant. See ordering information) Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 Low Forward Voltage Guard Ring Protection High Current Capability Extremely Low Thermal Resistance Maximum Ratings °C to +125°C • Operating Temperature: -55 • • Storage Temperature: -55°C to +150°C Maximum Thermal Resistance:RthjL-15 °C/W;Rthja- 71 °C/W MCC Catalog Number SK22-L SK23-L SK24-L SK25-L SK26-L SK28-L SK210-L SK2150-L SK220-L Device Marking Maximum Recurrent Peak Reverse Voltage 20V 30V 40V 50V 60V 80V 100V 150V 200V Maximum RMS Voltage 14V 21V 28V 35V 42V 56V 70V 105V 140V Maximum DC Blocking Voltage 20V 30V 40V 50V 60V 80V 100V 150V 200V B SK22 SK23 SK24 SK25 SK26 SK28 SK210 SK2150 SK220 C F H D G E Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage SK22-SK24 SK25-SK26 SK28-SK210 SK2150-SK220 Maximum DC Reverse Current At Rated DC Blocking Voltage SK22-SK24 SK25-SK210 SK2150-SK220 Typical Junction Capacitance SK22 SK23-SK210 SK2150-SK220 Note: IF(AV) 2.0A TL = 105°C DIMENSIONS IFSM 50A 8.3ms, half sine VF .50V .70V .85V .90V DIM A B C D E F G H INCHES MIN .160 .130 .006 .030 .200 .079 .075 .002 MAX .185 .155 .012 .060 .220 .096 .087 .008 MM MIN 4.06 3.30 0.15 0.76 5.08 2.00 1.91 0.05 MAX 4.70 3.94 0.31 1 ..52 5.59 2.44 2.21 0.203 NOTE IFM = 2.0A; TJ = 25°C* TJ = 25°C SUGGESTED SOLDER PAD LAYOUT 0.106" IR 2.0 mA 1.0 mA 0.5 mA 0.083” CJ 230pF 50pF 170 pF Measured at 1.0MHz, VR=4.0V 0.050” *Pulse test: Pulse width 300 µsec, Duty cycle 2% 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. Revision: C www.mccsemi.com 1 of 4 2011/06/03 SK22-L thru SK210-L Rating and Characteristic Curves I(AV), AVERAGE FORWARD CURRENT (A) 10 MCC IF, INSTANTANEOUS FORWARD CURRENT (A) SK22 - SK24 2.0 SK25 - SK26 1.0 SK28 - S210 1.0 0.1 0 25 50 75 100 125 150 0.01 Tj - 25ºC IF Pulse Width = 300 µs 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 VF, INSTANTANEOUS FWD VOLTAGE (V) Fig. 2 Typ. Forward Characteristics 1000 Tj = 25° C f = 1 MHz TL , LEAD TEMPERATURE (ºC) Fig. 1 Forward Current Derating Curve 60 IFSM, PEAK FORWARD SURGE CURRENT (A) Single Half Sine-Wave 45 Cj, JUNCTION CAPACITANCE (pF) 100 (JEDEC Method) 30 100 15 Tj = 150ºC 0 1 10 NUMBER OF CYCLES AT 60 Hz 10 0.1 1 10 100 Fig. 3 Max Non-Repetitive Peak Fwd Surge Current VR, REVERSE VOLTAGE (V) Fig. 4 Typical Junction Capacitance IR, INSTANTANEOUS REVERSE CURRENT (mA) 100 10 Tj = 100ºC 1.0 Tj = 75ºC 0.1 0.01 Tj = 25ºC 0.001 0 20 40 60 80 100 120 140 Revision: C www.mccsemi.com 2 of 4 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Fig. 5 Typical Reverse Characteristics 2011/06/03 SK2150-L thru SK220-L Rating and Characteristic Curves MCC F IG . 2-T Y P IC AL F O R W AR D CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) 2.4 2.0 50 1.2 0.8 0.4 INSTANTANEOUS FORWARD CURRENT,(A) 1.6 10 00 20 40 60 80 100 120 140 160 180 200 1.0 AMBIENT TEMPERATURE,( C) Tj=25 C Pulse Width 300us F IG . 3-MAX IMU M NO N-R E P E T IT IV E F O R W AR D S U R G E C U R R E NT 0.1 PEAK FORWARD SURGE CURRENT,(A) 50 .01 40 .1 .3 .5 .7 .9 1.1 1.3 1.5 30 Tj=25 C 8.3ms Single Half Sine Wave JEDEC method FORWARD VOLT AGE,(V) 20 10 FIG.5 - TYPICAL REVERSE 0 1 5 10 50 100 100 CHARACTERISTICS NUMBER OF CYCLES AT 60Hz REVERSE LEAKAGE CURRENT, (mA) 50 100 FIG.4-TYPICAL JUNCTION CAPACITANCE 700 10 JUNCTION CAPACITANCE,(pF) 600 500 400 1.0 300 .1 200 100 0 ..01 .01 .05 .1 .5 1 5 10 0 20 40 60 80 100 120 140 REVERSE VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLT E , (% ) AG Revision: C www.mccsemi.com 3 of 4 2011/06/03 MCC TM Micro Commercial Components Ordering Information : Device Part Number-TP Packing Tape&Reel: 3Kpcs/Reel ***IMPORTANT NOTICE* ** Micro Comme rcial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Comme rcial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Co mponents Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from A uthorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC' s quality standards for handling and storage. MCC will not pro vide any warranty coverage or o ther assistance for parts bought from Unau thorized Source s. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. Revision: C www.mccsemi.com 4 of 4 2011/06/03 3