SS15E-TP

SS12E THRU SS110E Features • Lead Free Finish/RoHS Compliant(Note 1) ("P" Suffix Designates Compliant. See Ordering Information) • Halogen Free Available Upon Request By Adding Suffix "-HF" • Low Forward Voltage • Guard Ring Protection • High Current Capability • Epoxy Meets UL 94 V-0 Flammability Rating • Moisture Sensitivity Level 1 1.0 Amp Schottky Rectifier 20 to 100 Volts Maximum Ratings • Operating Junction Temperature Range(SS12E~14E): -55⁰C to +125⁰C • Operating Junction Temperature Range(SS15E~110E): -55°C to +150°C • Storage Temperature Range: -55⁰C to +150⁰C SMAE • Maximum Thermal Resistance: 28°C/W Junction to Lead • Maximum Thermal Resistance: 90°C/W Junction to Ambient MCC Part Number SS12E SS13E SS14E SS15E SS16E SS18E SS110E Device Marking Maximum Maximum DC Recurrent Maximum Blocking Peak Reverse RMS Voltage Voltage Voltage SS12 SS13 SS14 SS15 SS16 SS18 SS110 20V 30V 40V 50V 60V 80V 100V 14V 21V 28V 35V 42V 56V 70V H J 20V 30V 40V 50V 60V 80V 100V Cathode Mark 1.0A TL=100⁰C Peak Forward Surge Current 30A 8.3ms,Half Sine VF 0.60V 0.70V 0.85V IFM=1.0A; TJ=25°C* IR 0.1mA 10mA 50μA 5mA 10μA 2mA TJ=25⁰C TJ=100⁰C TJ=25⁰C TJ=100⁰C TJ=25⁰C TJ=100⁰C 110pF 30pF Measured at 1.0MHz VR=4.0V Maximum Instantaneous Forward Voltage SS12E-SS14E SS15E-SS16E SS18E-SS110E Maximum DC Reverse Current at Rated DC Blocking Voltage SS12E-SS14E IFSM SS15E-SS16E SS18E-SS110E Typical Junction Capacitance SS12E-SS16E SS18E-SS110E CJ C A E D F B G Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current IF(AV) Cathode Band DIM A B C D E F G H J DIMENSIONS INCHES MM MIN MAX MIN MAX 0.079 0.096 2.01 2.44 0.045 0.071 1.15 1.80 0.002 0.008 0.05 0.20 --- 0.020 --0.51 0.030 0.060 0.76 1.52 0.065 0.084 1.65 2.13 0.189 0.208 4.80 5.30 0.157 0.180 4.00 4.57 0.090 0.115 2.29 2.92 NOTE Suggested Solder Pad Layout 2.29mm 2.16mm 1.78mm *Pulse Test: Pulse width 300 μsec, Duty cycle 2% Note :1. High Temperature Solder Exemption Applied, See EU Directive Annex 7a. Rev.3-3-12012020 1/4 MCCSEMI.COM SS12E THRU SS110E Curve Characteristics Fig. 2 - Maximum Non-Repetitive Peak Forward Surge Current 35 1.0 30 Peak Forward Surge Current (A) Average Forward Current (A) Fig. 1 - Forward Current Derating Curve 1.2 0.8 SS15E - SS110E 0.6 0.4 SS12E - SS14E 0.2 Resistive or Inductive Load 0.0 0 25 50 75 100 125 150 15 10 5 8.3 ms Single Half Sine-Wave 10 1 100 Lead Temperature (°C) Number of Cycles at 60 Hz Fig. 3 - Typical Instantaneous Forward Characteristics Fig. 4 - Typical Instantaneous Forward Characteristics 5 TJ=125°C 2 Instantaneous Forward Current (A) Instantaneous Forward Current (A) 20 0 175 5 1 0.5 0.2 0.1 TJ=75°C 0.05 TJ=25°C 0.02 0.01 0.0 0.2 0.1 0.3 SS12E~14E 0.4 0.5 0.6 0.7 TJ=125°C 2 1 0.5 0.2 0.1 TJ=75°C 0.05 TJ=25°C 0.02 0.01 0.0 0.8 0.1 0.2 0.3 0.4 SS15E~16E 0.5 0.6 0.7 Instantaneous Forward Voltage (V) Instantaneous Forward Voltage (V) Fig. 5 - Typical Instantaneous Forward Characteristics Fig. 6 - Typical Reverse Leakage Characteristics 5 TJ=125°C 2 1 0.5 0.2 0.1 TJ=75°C 0.05 0.02 0.01 0.0 SS18E-110E TJ=25°C 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 TJ=125°C 1000 100 TJ=75°C 10 TJ=25°C 1 20 40 60 SS14E 80 100 Percent of Rated Peak Reverse Voltage (%) Instantaneous Forward Voltage (V) Rev.3-3-12012020 0.8 10000 Instantaneous Reverse Leakage Current (μA) Instantaneous Forward Current (A) 25 2/4 MCCSEMI.COM SS12E THRU SS110E Curve Characteristics Fig. 7 - Typical Reverse Leakage Characteristics Fig. 8 - Typical Reverse Leakage Characteristics 1000 1000 Instantaneous Reverse Leakage Current (μA) Instantaneous Reverse Leakage Current (μA) 10000 TJ=125°C 100 TJ=75°C 10 1 20 SS16E TJ=25°C 40 60 80 100 Percent of Rated Peak Reverse Voltage (%) Rev.3-3-12012020 100 TJ=125°C 10 TJ=75°C 1 0.1 TJ=25°C 0.01 20 40 60 SS110E 80 100 Percent of Rated Peak Reverse Voltage (%) 3/4 MCCSEMI.COM SS12E THRU SS110E Ordering Information Device Packing Part Number-TP Tape&Reel: 6Kpcs/Reel Note : Adding "-HF" Suffix For Halogen Free, eg. Part Number-TP-HF ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. Micro Commercial Components Corp. products are sold subject to the general terms and conditions of commercial sale, as published at https://www.mccsemi.com/Home/TermsAndConditions. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. Rev.3-3-12012020 4/4 MCCSEMI.COM