UFM15PL-TP

MCC TM Micro Commercial Components UFM11PL THRU UFM17PL
  omponents 20736 Marilla Street Chatsworth    !"# $ %    !"# Features 1 Amp Ultra Fast Recovery Silicon Rectifier 50 to 1000 Volts Halogen free available upon request by adding suffix "-HF" Ultra fast Recovery High Reliability Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 Lead Free Finish/RoHS Compliant (Note1)("P"Suffix designates Compliant. See ordering information) • x x • • x Maximum Ratings x x x SOD-123FL Operating Temperature: -65qC to +150qC Storage Temperature: -65qC to +150qC Maximum Thermal Resistance; 180qC/W Junction To Ambient. MCC Part Number Device Marking UFM11PL UFM12PL UFM13PL UFM14PL UFM15PL UFM16PL UFM17PL U1 U2 U3 U4 U5 U6 U7 Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V 600V 800V 1000V Maximum RMS Voltage 35V 70V 140V 280V 420V 560V 700V Maximum DC Blocking Voltage 50V 100V 200V 400V 600V 800V 1000V A B C E H D G Electrical Characteristics @ 25qC Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage UFM11PL-13PL UFM14PL UFM15PL-17PL Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time UFM11PL-13PL UFM14PL UFM15PL-17PL Typical Junction Capacitance IF(AV) 1.0A TL = 90qC IFSM 30A 8.3ms, half sine VF 1.0V 1.40V 1.70V IFM = 1.0A; Ta = 25qC IR 10PA 50PA Ta = 25qC Ta = 125qC Trr CJ 35ns 50ns 75ns IF = 0.5A,IR=1.0A, I rr= 0.25Α 20pF Measured at 1.0MHz, VR=4.0V DIM A B C D E G H DIMENSIONS INCHES MM MIN MAX MIN MAX .140 .152 3.55 3.85 .100 .122 2.55 3.10 .055 .075 1.40 1.90 .035 .053 0.90 1.35 .020 .041 0.50 1.05 .010 ----0.25 --------.010 ---.25 NOTE SUGGESTED SOLDER PAD LAYOUT 0.093” 0.048” 0.036” Note: 1. High Temperature Solder Exemption Applied, see EU Directive Annex 7. Revision: E www.mccsemi.com 1 of 4 2016/02/25 MCC UFM11PL THRU UFM17PL TM Micro Commercial Components TYPICAL CHARACTERISTICS 4.00 4.00 4.00 UFM11PL-13PL UFM11PL-13PL 3.00 UFM11PL-13PL 3.00 3.00 1.00 UFM14PL 2.00 1.00 UFM15PL-17PL Amps UFM14PL 2.00 Amps Amps Figure 3 Typical Forward Characteristics Figure 2 Typical Forward Characteristics Figure 1 Typical Forward Characteristics 1.00 UFM15PL-17PL TJ=0°C TJ=100°C 0.01 0.8 UFM15PL-17PL TJ=25°C 0.01 0.6 UFM14PL 2.00 1.0 1.2 1.4 1.6 1.8 2.0 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts 0.01 0.6 0.8 1.2 1.4 1.6 1.8 2.0 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts 1.0 1.2 1.4 1.6 1.8 2.0 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts 0.5 0.8 1.0 Figure 4 Junction Capacitance 100 60 40 UFM11PL-UFM14PL 20 pF TJ=25°C; f=1MHZ UFM15-17PL 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 Junction Capacitance - pFversus Reverse Voltage - Volts Revision: E www.mccsemi.com 2 of 4 2016/02/25 MCC UFM11PL THRU UFM17PL Micro Commercial Components TYPICAL CHARACTERISTICS 30 Figure 6 Forward Derating Curve Figure 5 Peak Forward Surge Current 2.4 2.2 25 2.0 20 1.8 1.6 15 Amps 1.4 10 Amps 5 0 1.2 1.0 .8 1 2 4 6 8 10 20 40 .6 60 80 100 .4 Single Phase, Half Wave .2 60Hz Resistive or Inductive Load Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles 0 25 0 50 75 100 125 150 °C Figure 7 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω Average Forward Rectified Current - Amperesversus Lead Temperature -°C 10Ω +0.5A trr 0 Pulse Generator Note 2 25Vdc 1Ω Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive www.mccsemi.com Revision: E 3 of 4 TM 2016/02/25 MCC TM Micro Commercial Components Ordering Information : Device Packing Part Number-TP Tape&Reel: 2.5Kpcs/Reel Note : Adding "-HF" suffix for halogen free, eg. Part Number-TP-HF ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. www.mccsemi.com Revision: E 4 of 4 2016/02/25