800S-N024

800W Single Output With Parallel Function Features : SCN-800 series AC input range selected by switch Protections: Short circuit / Overload / Over voltage / Over temp. High reliability/ Low ripple noise Built-in remote sense function Built-in remote ON-OFF control Built-in parallel operation function Can adjust from 20~100% output voltage by external control 1-5V Forced air cooling by built-in DC fan Case coating with paint 2 years warranty SPECIFICATION ORDER NO. SAFETY MODEL NO. DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE LINE REGULATION LOAD REGULATION SCN-800-12 800S-N012 12V 66A 0 ~ 66A 792W SCN-800-15 800S-N015 15V 54A 0 ~ 54A 810W 150mVp-p SCN-800-24 800S-N024 24V 33A 0 ~ 33A 792W 240mVp-p 20~100% adjustment by 1~5VDC external control 1.0% 0.5% 0.5% SCN-800-48 800S-N048 48V 16.6A 0 ~ 16.6A 796W 480mVp-p 1.0% 0.5% 0.5% RIPPLE & NOISE (max.) Note.2 150mVp-p 5.0% typical adjustment by potentiometer 1.0% VOLTAGE TOLERANCE Note.3 1.0% 0.5% 0.5% 0.5% 0.5% SETUP, RISE, HOLD UP TIME 800ms, 50ms, 16ms at full load 90 ~ 130VAC / 180 ~ 260VAC selected by switch, 260 ~ 370VDC VOLTAGE RANGE FREQUENCY RANGE INPUT EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT (max.) LEAKAGE CURRENT (max.) OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING TEMP., HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 47 ~ 63Hz 80% 17A / 115VAC 9A / 230VAC 60A / 230VAC 3.5mA / 240VAC 110 ~ 135% rated output power Protection type : Current limiting, delay shut down o/p voltage, re-power on to recover 110 ~ 135% follow to output set up point Protection type : Shut down o/p voltage, re-power on to recover >100 / measure by heat sink, near transformer Protection type : Shut down o/p voltage, re-power on to recover -10 ~ +65 (Refer to output load derating curve) 20% ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.04% / (0 ~ 50 ) 10 ~ 200Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes Design refer to UL1950, CSA22.2, IEC60950 I/P-O/P, I/P-FG:1500VAC I/P-O/P, I/P-FG, >100M Ohms / 500VDC / 25 81% 85% 87% SAFETY & ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION Design refer to FCC part 15 class A (Note. 4) HARMONIC CURRENT ---EMS IMMUNITY ---MTBF OTHERS DIMENSION PACKING SPECIAL FUNCTION 120khrs min. MIL-HDBK-217F (25 / 70% RH ) 291*132*68mm (L*W*H) 2.3kg; 8pcs/ 24kg /CARTON DC voltage adj., Remote sensing, remote control, parallel operation (refer to terminal instruction manual) NOTE 1.All parameters are specified at 230VAC input, rated load, 25 70% RH ambient. 2.Tolerence: includes set up tolerance, line regulation, load regulation. 3.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 4.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:SCN-800-SPEC 2007-11-01 800W Single Output With Parallel Function Mechanical Specification SCN-800 series Unit:mm 291 200 199.5 L N FG 50.5 41 15.5 68 AC INPUT #6-32-4 M3(NUT)x3H-4 30 15 POS+ 291 9 250 M3(NUT)x3H-4 Air flow direction 32 DC OUTPUT POS 9.5 AC INPUT BOTTOM SIDE M6 NEG Derating Curve External DC Control VS Output Voltage Vout 7.5 115 132 O.V.P. 100 100 OUTPUT VOLTAGE (%) 80 LOAD (%) non-linear 60 40 50 20 -10 0 10 20 30 40 50 60 V 1 2 3 4 5 Ta ( ) EXTERNAL VOLTAGE(Typical) File Name:SCN-800-SPEC 2007-11-01 VS+ VSVCI VCO GND PAR GND INH LED NEGV ADJ 800W Single Output With Parallel Function Control terminal instruction manual SCN-800 series LOAD LOAD LOAD VS+ VSVCI VCO GND PAR GND INH VS+ VSVCI VCO GND PAR GND INH VS+ VSVCI VCO GND PAR GND INH ON/OFF SWITCH USING INTERNAL VOLTAGE CONTROL REMOTE SENSING ON/OFF CONTROL BY SWITCH LOAD LOAD VS+ VSVCI VCO GND PAR GND INH H:ON L:OFF VS+ VSVCI VCO GND PAR GND INH DC 1-5V O N/OFF CONTROL BY TRANSISTOR OUTPUT VOLTAGE ADJUST WITH DC 1-5V LOAD LOAD VS+ VSVCI VCO GND PAR GND INH VS+ VSVCI VCO GND PAR GND INH VS+ VSVCI VCO GND PAR GND INH VS+ VSVCI VCO GND PAR GND INH VS+ VSVCI VCO GND PAR GND INH VS+ VSVCI VCO GND PAR GND INH PARALLEL OPERATION WITH REMOTE SENSING PARALLEL OPERATION File Name:SCN-800-SPEC 2007-11-01