APC-12-700

12W Single Output Switching Power Supply Features : Constant current design Universal AC input / Full range APC-12 series Protections:Short circuit / Over current / Over voltage Fully isolated plastic case Small and compact size Cooling by free air convection Pass LPS Suitable for LED lighting and moving sign applications 100% full load burn-in test Low cost / High reliability 2 years warranty F 110 SPECIFICATION MODEL RATED CURRENT DC VOLTAGE RANGE RATED POWER VOLTAGE TOLERANCE Note.3 CURRENT ACCURACY LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE INPUT EFFICIENCY(Typ.) AC CURRENT INRUSH CURRENT(max.) LEAKAGE CURRENT PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 5) Note.4 SELV LPS APC-12-350 350mA 9~36V 12.6W 5.0% 5.0% 1.0% 3.0% 3000ms, 180ms / 230VAC 90 ~ 264VAC 47 ~ 63Hz 82% 0.2A/230VAC;0.35A/115VAC Cold start 35A/115VAC,70A/230VAC 0.25mA / 240VAC 39.6~ 46.8V Protection type : Shut off o/p voltage, clamping by zener diode -30 ~ 70 -40 ~ +80 0.2%/ (Refer to "Derating Curve") , 10 ~ 95% RH (0 ~ 50 ) 20 ~ 90% RH non-condensing 3000ms, 150ms / 115VAC at full load 20ms/230VAC,15ms/115VAC at full load 127 ~ 370VDC APC-12-700 700mA 9~18V 12.6W 250mVp-p RIPPLE & NOISE (max.) Note.2 300mVp-p OUTPUT 80% 20.7~ 24.3V 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes Design refer to TUV EN60950-1, EN61347-2-13, UL8750 I/P-O/P:3.75KVAC I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015,EN61000-3-2 Class A,EN61000-3-3 Compliance to EN61547,EN61000-4-2,3,4,5,6,8,11; light industry level(surge 2KV), criteria A 1145.7K hrs min. MIL-HDBK-217F (25 ) 77*40*29(L*W*H) 0.08Kg; 120pcs/11.8Kg/0.93CUFT EMC EMISSION EMC IMMUNITY MTBF OTHERS NOTE DIMENSION PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristic for more details. 5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. File Name: APC-12-SPEC 2011-07-09 12W Single Output Switching Power Supply Mechanical Specification APC-12 series Unit:mm 90 82.5 77 150 10 +V(Red) -V(Black) 19 31 T case AC/N(Blue) AC/L(Brown) UL1569 18AWG 150 10 15.5 40 UL1569 20AWG T case: Max. Case Temperature Block Diagram POWER SWITCHING RECTIFIERS & FILTER DETECTION CIRCUIT PWM CONTROL 29 fosc : 67KHz I/P EMI FILTER RECTIFIERS +V -V Derating Curve 100 Static Characteristics 100 90 80 80 70 60 LOAD (%) LOAD (%) 0 10 20 30 40 45 50 60 70 (HORIZONTAL) 50 40 60 50 40 20 -30 90 100 200 210 220 230 240 250 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name: APC-12-SPEC 2011-07-09