APV-16-15

16W Single Output Switching Power Supply Features : A P V- 1 6 series Constant voltage design Universal AC input / Full range Protections: Short circuit / Over current / Over voltage Fully isolated plastic case Cooling by free air convection Small and compact size Pass LPS Suitable for LED lighting and moving sign applications 100% full load burn-in test Low cost, high reliability 2 years warranty F 110 SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE INPUT EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT(max.) LEAKAGE CURRENT OVER CURRENT PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & EMC WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE SELV LPS APV-16-5 5V 2.6A 0 ~ 2.6A 13W 5.0% 1.0% 2.0% Note.6 1500ms, 30ms / 230VAC APV-16-12 12V 1.25A 0 ~ 1.25A 15W 120mVp-p APV-16-15 15V 1A 0 ~ 1A 15W 120mVp-p APV-16-24 24V 0.67A 0 ~ 0.67A 16.08W 150mVp-p RIPPLE & NOISE (max.) Note.2 100mVp-p 1500ms,30ms / 115VAC at full load 20ms/230VAC Note.4 90 ~ 264VAC 12ms/115VAC at full load 127 ~ 370VDC 80% 70A/230VAC 81% 83% 47 ~ 63Hz 76% 0.3A/230VAC 0.5A/115VAC COLD START 35A/115VAC 0.25mA / 240VAC Above 105% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 5.75 ~ 6.75V 13.8 ~ 16V 17.5 ~ 21V Protection type : Shut off o/p voltage, clamping by zener diode -30 ~ +70 (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -40 ~ +80 , 10 ~ 95% RH 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes Design refer to TUV EN60950-1, EN61347-2-13,UL8750 I/P-O/P:3.75KVAC I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015,EN61000-3-2 Class A,EN61000-3-3 Compliance to EN61547,EN61000-4-2,3,4,5,6,8,11; light industry level(surge 2KV), criteria A 1145.7K hrs min. MIL-HDBK-217F (25 ) 77*40*29mm (L*W*H) 0.1Kg; 120pcs/14Kg/0.93CUFT 27.6 ~ 32.4V 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. File Name:APV-16-SPEC 2011-07-09 16W Single Output Switching Power Supply Mechanical Specification A P V- 1 6 series Unit:mm 90 82.5 77 150 10 +V(Red) -V(Black) 19 31 T case AC/N(Blue) AC/L(Brown) UL1569 18AWG 150 10 15.5 40 UL1569 20AWG T case: Max. Case Temperature Block Diagram POWER SWITCHING RECTIFIERS & FILTER DETECTION CIRCUIT PWM CONTROL 29 fosc : 67KHz I/P EMI FILTER RECTIFIERS +V -V Derating Curve 100 Static Characteristics 100 90 80 80 70 60 LOAD (%) LOAD (%) 0 10 20 30 40 50 60 70 (HORIZONTAL) 50 40 60 50 40 20 -30 90 100 200 210 220 230 240 250 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz F ile Name:APV-16-SPEC 2011-07-09