CEN-100-54

100W Single Output LED Power Supply ½ Features : CEN-100 series Universal AC input / Full range (up to 295VAC) Protections: Short circuit / Over current / Over voltage / Over temperature Output voltage and constant current level adjustable Built-in active PFC function IP66 design for indoor or outdoor installations Cooling by free air convection 100% full load burn-in test High reliability Suitable for LED lighting and moving sign applications Compliance to worldwide safety regulations for lighting Suitable for dry / damp / wet locations 3 years warranty F 110 SELV SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT CEN-100-20 20V 4.8A 0 ~ 4.8A 96W CONSTANT CURRENT OPERATION VOLTAGE Note.5 13 ~ 20V CEN-100-24 24V 15.6 ~ 24V 4A 0 ~ 4A 96W 2.7Vp-p 22 ~ 27V 2.6 ~ 4A CEN-100-30 30V 19.5 ~ 30V 3.2A 0 ~ 3.2A 96W 3Vp-p 27 ~ 33V 2.08 ~ 3.2A IP66 CEN-100-36 36V 23.4 ~ 36V 2.65A 0 ~ 2.65A 95.4W 3.6Vp-p 33 ~ 40V 1.72 ~ 2.65A CEN-100-42 42V 27.3 ~ 42V 2.28A 0 ~ 2.28A 95.76W 4Vp-p 37 ~ 46V 1.48 ~ 2.28A CEN-100-48 48V 31.2 ~ 48V 2A 0 ~ 2A 96W 4.6Vp-p 43 ~ 53V 1.3 ~ 2A CEN-100-54 54V 35.1 ~ 54V 1.77A 0 ~ 1.77A 95.58W 5Vp-p 49 ~ 58V 1.15 ~ 1.77A RIPPLE & NOISE (max.) Note.2 2.0Vp-p VOLTAGE ADJ. RANGE (SVR1) 17 ~ 22V CURRENT ADJ. RANGE(SVR2) 3.12 ~ 4.8A VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP TIME VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & EMC WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE 10% 3.0% 5.0% 3000ms / 230VAC 5000ms / 115VAC at full load Note.4 90 ~ 295VAC 127 ~ 417VDC 47 ~ 63Hz PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) 88% 1.4A/115VAC 60A/230VAC 89% 0.7A/230VAC 90% 90% 90% 91% 91% 100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN61000-3-2 Class C ( 65% load) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV), criteria A 519.5Khrs min. MIL-HDBK-217F (25 193*62.5*40.5mm (L*W*H) 0.6Kg; 24pcs/15.4Kg/1.11CUFT ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. Constant current operation region is within 65% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. File Name:CEN-100-SPEC 2011-07-28 100W Single Output LED Power Supply Mechanical Specification CEN-100 Case No. 993A series Unit:mm 193 10.5 7.6 300 20 300 20 SVT 18AWG 2C 30.64 172 SJTW 18AWG 3C 4.6 4PL T case: Max. Case Temperature. 31.25 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) 30.6 45 62.5 T case 86 Vo Io ADJ. ADJ. +V(Red) -V(Black) Block Diagram RECTIFIERS & FILTER DETECTION CIRCUIT PWM & PFC CONTROL O.V.P. fosc : 42KHz(115VAC) 68KHz(230VAC) POWER SWITCHING +V -V I/P EMI FILTER & RECTIFIERS FG O.L.P. O.C.P. Derating Curve Static Characteristics 100 100 90 80 80 70 60 LOAD (%) 40 LOAD (%) 60 50 40 20 -30 -25 -5 0 15 30 50 60 70 (HORIZONTAL) 90 100 125 135 145 155 165 175 180 200 230 295 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz File Name:CEN-100-SPEC 2011-07-28 40.5 100W Single Output LED Power Supply Power Factor Characteristic Constant Current Mode 1 .0 0 0 .9 8 0 .9 6 0 .9 4 0 .9 2 0 .9 0 0 .8 8 0 .8 6 0 .8 4 0 .8 2 0 .8 0 0 .7 8 50% 60% 70% 80% 90% 100% (100W) CEN-100 series PF 2 7 7 V ac 2 3 0 V ac 1 1 5 V ac LOAD EFFICIENCY vs LOAD (48V Model) CEN-100 series possess superior working efficiency that up to 91% can be reached in field applications. 94 90 86 EFFICIENCY (%) 82 78 74 70 66 62 58 54 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD 277Vac 230Vac 115Vac DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)]. 100 (B) Constant Current area (A) Constant Voltage area 65 (max.) (C) Hiccup Protection 50 100 Io (%) Vo(%) Typical LED power supply I-V curve File Name:CEN-100-SPEC 2011-07-28