LPL-18_1111

18W Single Output Switching Power Supply Features : 90-132VAC input only LPL-18 series Fully encapsulated with IP67 level (Note.5) Protections:Short circuit/Over load/Over voltage/Over temperature Cooling by free air convection Class power unit, no FG Pass LPS 100% full load burn-in test Suitable for LED lighting and moving sign applications High reliability/Low cost 2 years warranty SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE INPUT EFFICIENCY(Typ.) AC CURRENT INRUSH CURRENT(max.) LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMC EMISSION EMC IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE LPS IP67 LPL-18-12 12V 1.5A 0 ~ 1.5A 18W 3.0% 1.0% 2.0% 1500ms, 30ms / 115VAC 20ms/115VAC at full load 90 ~ 132VAC 47 ~ 63Hz 80% 0.5A/115VAC Cold start 40A/115VAC 0.25mA / 115VAC Above 105% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 13.8~ 16.2V Tj 140 -30~ +70 -40 ~ +80 0.03%/ 27.6~ 32.4V 41.4 ~ 48.6V Protection type : Shut off o/p voltage, clamping by zener diode typically (U1) detect on main control IC (Refer to "Derating Curve") , 10 ~ 95% RH (0 ~ 50 ) Protection type :Shut down, recovers automatically after temperature goes down 20 ~ 90% RH non-condensing 83% 84% 127 ~ 186VDC LPL-18-24 24V 0.75A 0 ~ 0.75A 18W 150mVp-p LPL-18-36 36V 0.5A 0 ~ 0.5A 18W 200mVp-p (LVD) RIPPLE & NOISE (max.) Note.2 120mVp-p 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes IP67 approved; design refer to UL1310 Class 2,TUV EN60950-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91 I/P-O/P:3KVAC I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55022 (CISPR22) Class B, FCC Part 15, EN61000-3-2 Class A, EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A 1207.4Khrs min. MIL-HDBK-217F(25 140*30*22(L*W*H) 0.175Kg; 70pcs/13.3Kgs/0.71CUFT ) 1. All parameters NOT specially mentioned are measured at 115VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 5. Suitable for indoor use or outdoor use without direct sunlight exposure. File Name: LPL-18-SPEC 2011-11-08 18W Single Output Switching Power Supply Mechanical Specification LPL-18 series Unit:mm 300 20 140 300 20 3.5 3.5 DC OUT AC/N(Blue) AC/L(Brown) AC IN UL 1015 18AWG 3.5 3.5 30 3.6 UL 1015 18AWG -V(Black) +V(Red) 3.6 Block Diagram RECTIFIERS & FILTER DETECTION CIRCUIT PWM CONTROL fosc : 60KHz I/P EMI FILTER RECTIFIERS POWER SWITCHING 22 +V -V Derating Curve 100 Static Characteristics 100 90 80 80 70 60 LOAD (%) LOAD (%) 0 10 20 30 40 50 60 70 (HORIZONTAL) 40 60 50 40 20 -30 90 100 110 120 132 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name: LPL-18-SPEC 2011-11-08