NSD05-S

5W DC-DC Regulated Single Output Features : Wide 4:1 DC input range NSD05-S Protections: Short circuit / Overload / Over voltage 1000VDC I/O isolation Cooling by free air convection Built-in remote ON-OFF control 100% full load burn-in test Low cost High reliability 2 years warranty series SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT CAPACITIVE LOAD (max.) VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION RATED DC INPUT VOLTAGE RANGE EFFICIENCY (Typ.) DC CURRENT SHUTDOWN IDLE CURRENT OVERLOAD PROTECTION OVER VOLTAGE(CLAMP) SHORT CIRCUIT ON/OFF CONTROL WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY NSD05-12S3 3.3V 1.2A 0 ~ 1.2A 3.96W 1000uF 2.0% max. 1.0% 2.0% 12VDC 9.2 ~ 36VDC 72% 0.7A/12VDC 5mA/12VDC 1.0% 1.0% 1.0% 2.0% 48VDC 18 ~ 72VDC 75% 0.2A/48VDC 5mA/48VDC 1.0% 1.0% 1.0% NSD05-12S5 5V 1A 0 ~ 1A 5W 1000uF NSD05-12S12 NSD05-12S15 NSD05-48S3 12V 0.42A 0 ~ 0.42A 5.04W 120uF 15V 0.33A 0 ~ 0.33A 4.95W 120uF 3.3V 1.2A 0 ~ 1.2A 3.96W 1000uF NSD05-48S5 5V 1A 0 ~ 1A 5W 1000uF NSD05-48S12 NSD05-48S15 12V 0.42A 0 ~ 0.42A 5.04W 120uF 15V 0.33A 0 ~ 0.33A 4.95W 120uF RIPPLE & NOISE (max.) Note.2 75mVp-p INPUT 76% 82% 83% 78% 83% 85% FUNCTION Above 105% rated output power Protection type : Over power limiting, recovers automatically after fault condition is removed 3.8 ~ 4.6V 5.6 ~ 6.8V 13.5 ~ 16.5V 16.2 ~ 19.8V 3.8 ~ 4.6V 5.6 ~ 6.8V Recovers automatically after fault condition is removed Logic "1" or open circuit : ON Logic "0" or short to PIN2 : OFF -25 ~ +70 0% ~ 95% RH max. -40 ~ +85 , 0 ~ 95% RH 0.03%/ (0~60 IEC60950-1 CB approved by TUV I/P-O/P:1KVDC I/P-O/P:100M Ohms/500VDC 25 70%RH Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-4-2,3,4,5,6,8; EN55024, light industry level, criteria A 914.4K hrs min. MIL-HDBK-217F (25 ) 40.6*25.4*8.3mm (1.6"*1"*0.327") (L*W*H) 0.007Kg; 700pcs/5.9Kg/0.97CUFT 13.5 ~ 16.5V 16.2 ~ 19.8V ENVIRONMENT TEMP. COEFFICIENT SAFETY STANDARDS SAFETY & ISOLATION VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMI CONDUCTION & RADIATION EMS IMMUNITY MTBF OTHERS NOTE DIMENSION PACKING 1. All parameters NOT specially mentioned are measured at 12, 48VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. For the input line, a 47uF/100V electrolytic capacitor with Esr