NSD10-D_11

10W DC-DC Regulated Dual Output Features : Wide 4:1 DC input range NSD10-D Protections: Short circuit / Overload / Over voltage 1000VDC I/O isolation Built-in EMI filter Cooling by free air convection Built-in remote ON-OFF control 100% full load burn-in test Lost cost High reliability 2 years warranty series SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT CAPACITIVE LOAD (max.) VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION RATED DC INPUT VOLTAGE RANGE EFFICIENCY (Typ.) DC CURRENT SHUTDOWN IDLE CURRENT OVERLOAD PROTECTION NSD10-12D5 5V 1A 10W 1000uF 4.0% 1.0% 3.0% 12VDC 9.8 ~ 36VDC 76% 1.4A/12VDC 20mA/12VDC 2.0% 1.0% 2.0% 48VDC 22 ~ 72VDC 78% 0.4A/48VDC 2.0% 1.0% 2.0% 2.0% 3.0% 2.0% 2.0% -5V 1A NSD10-12D12 12V 0.42A 10.08W -12V 0.42A NSD10-12D15 15V 0.33A 9.9W -15V 0.33A NSD10-48D5 5V 1A 10W -5V 1A NSD10-48D12 12V 0.42A 10.08W -12V 0.42A NSD10-48D15 15V 0.33A 9.9W -15V 0.33A 0.05 ~ 1A 0.05 ~ 1A 0.02 ~ 0.42A 0.02 ~ 0.42A 0.016 ~ 0.33A 0.016 ~ 0.33A 0.05 ~ 1A 0.05 ~ 1A 0.02 ~ 0.42A 0.02 ~ 0.42A 0.016 ~ 0.33A 0.016 ~ 0.33A RIPPLE & NOISE (max.) Note.2 75mVp-p(10% ~ 100% load) INPUT 77% 77% 77% 77% Above 105% rated output power Protection type : Over power limiting, recovers automatically after fault condition is removed -5.75 ~ -7.5V 13.8 ~ 18V -13.8 ~ -18V 17.3 ~ 22.5V -17.3 ~ -22.5V FUNCTION OVER VOLTAGE(CLAMP) 5.75 ~ 7.5V -5.75 ~ -7.5V 13.8 ~ 18V -13.8 ~ -18V 17.3 ~ 22.5V -17.3 ~ -22.5V 5.75 ~ 7.5V SHORT CIRCUIT Note.4 Recovers automatically after fault condition is removed Logic "1" OPEN: ON logic "0" GND: OFF ON/OFF CONTROL -25 ~ +70 WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY 0% ~ 95% RH max. -40 ~ +85 , 0 ~ 95% RH 0.03%/ (0~60 ) UL60950-1 approved, Design refer to TUV EN60950-1 I/P-O/P:1KVDC I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55022 (CISPR22) Class B ENVIRONMENT TEMP. COEFFICIENT SAFETY STANDARDS SAFETY & ISOLATION VOLTAGE ISOLATION RESISTANCE EMC (Note 5) EMC EMISSION EMC IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE Compliance to EN61000-4-2,3,4,6,8; EN55024, light industry level, criteria A 1878.5K hrs min. MIL-HDBK-217F (25 50.8*25.4*10mm (2"*1"*0.394") (L*W*H) 0.02Kg; 300pcs/7Kg/0.97CUFT ) 1. All parameters NOT specially mentioned are measured at 12, 48VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Short circuit not more than 60 seconds. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 6. To insure proper operation, a 220uF/100V electrolytic capacitor with Esr