PLN-100-15

100W Single Output Switching Power Supply Features : PLN-100 series Universal AC input / Full range (up to 295VAC) High efficiency up to 88.5% Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection Built-in active PFC function IP64 design for indoor or outdoor installations Pass LPS Class 2 power unit 100% full load burn-in test High reliability Suitable for LED lighting and moving sign applications Suitable for dry / damp locations Compliance to worldwide safety regulations for lighting 2 years warranty F 110 M M SELV LPS ( for 48V only) ( except for 48V ) IP64 PLN-100-36 36V 27 ~ 36V 2.65A 95.4W 150mVp-p 30.6 ~ 36V 2 ~ 2.65A 2.0% PLN-100-48 48V 36 ~ 48V 2A 96W 200mVp-p 40.8 ~ 48V 1.5 ~ 2A 2.0% SPECIFICATION MODEL DC VOLTAGE RATED CURRENT RATED POWER PLN-100-12 12V Note.5 5A Note.5 60W PLN-100-15 15V 11.25 ~ 15V 5A 75W 150mVp-p 12.8 ~ 15V 3.75 ~ 5A 3.0% PLN-100-20 20V 15 ~ 20V 4.8A 96W 150mVp-p 17 ~ 20V 3.6 ~ 4.8A 3.0% PLN-100-24 24V 18 ~ 24V 4A 96W 150mVp-p 20.4 ~ 24V 3 ~ 4A 3.0% PLN-100-27 27V 20.25 ~ 27V 3.55A 95.85W 150mVp-p 23 ~ 27V 2.6 ~ 3.55A 3.0% CONSTANT CURRENT REGION Note.6 9 ~ 12V RIPPLE & NOISE (max.) Note.2 150mVp-p OUTPUT VOLTAGE ADJ. RANGE (SVR1) 10.2 ~ 12V CURRENT ADJ. RANGE(SVR2) 3.75 ~ 5A VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS Note.7 SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE 3.0% 1.0% 2.0% 1200ms, 80ms/230VAC 1200ms, 80ms/115VAC at full load 60ms/230VAC 30ms/115VAC at full load Note.4 90 ~ 295VAC 127 ~ 417VDC 47 ~ 63Hz PF>0.95/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) 83% 12V:0.8A/115VAC 85% 88.5% 88.5% 15V:0.9A/115VAC 0.45A/277VAC 88% 88% 88.5% 0.4A/230VAC 0.3A/277VAC 0.45A/230VAC 0.35A/277VAC 20V ~ 48V:1.1A/115VAC 0.55A/230VAC COLD START 40A/230VAC 75% load) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A 303.1Khrs min. MIL-HDBK-217F (25 200*70.5*35mm (L*W*H) 0.52Kg; 20pcs/12.5Kg/0.76CUFT ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. This is the maximum possible output current and power. Over load protection may be activated slightly below this level to comply with the requirement of UL1310 class 2. 6. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18. 8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. File Name:PLN-100-SPEC 2012-03-12 100W Single Output Switching Power Supply Mechanical Specification 200 6.26 22.84 PLN-100 Case No.955A series Unit:mm 2-R2.5 70.5 310 20 310 20 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) T case 35.25 100 SVT 18AWG 2C 22.84 +V(Red) -V(Black) SVT 18AWG 3C T case: Max. Case Temperature. 6.26 Output voltage and current adjustment : remove the upper case and adjust through SVR1 & SVR2 shown in the diagram. SVR1 SVR2 SVR1 Output voltage adjustment SVR2 Output current adjustment Block Diagram RECTIFIERS & FILTER O.L.P. FG PFC CONTROL DETECTION CIRCUIT O.V.P. Fosc : 100KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING 35 +V -V O.L.P. PWM & PFC CONTROL Derating Curve Static Characteristics 100 100 90 80 230VAC Input only 80 70 60 LOAD (%) 40 LOAD (%) -25 -10 0 15 30 40 50 (HORIZONTAL) 60 50 40 20 -30 90 100 125 135 145 155 165 175 180 200 230 295 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz File Name:PLN-100-SPEC 2012-03-12 100W Single Output Switching Power Supply Power Factor Characteristic Constant Current Mode 1 .0 0 0 .9 8 0 .9 6 0 .9 4 0 .9 2 0 .9 0 0 .8 8 0 .8 6 0 .8 4 0 .8 2 0 .8 0 0 .7 8 50% 60% 70% 80% 90% 100% (100W) PLN-100 series 277V ac 230V ac 115V ac PF LOAD EFFICIENCY vs LOAD (48V Model) PLN-100 series possess superior working efficiency that up to 89% can be reached in field applications. 92 88 84 EFFICIENCY (%) 80 277Vac 76 72 68 64 60 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD 230Vac 115Vac DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)]. 100 (B) Constant Current area (A) Constant Voltage area 75 (max.) (C) Hiccup Protection 50 100 Io (%) Vo(%) Typical LED power supply I-V curve File Name:PLN-100-SPEC 2012-03-12