20W Single Output LED Power Supply
Features :
PLN-20
series
Universal AC input / Full range(up to 277VAC) Built-in constant current limiting circuit with adjustable OCP level Fully isolated plastic case Protections:Short circuit/Over load/Over voltage/Over temperature Built-in active PFC function IP64 design for indoor or outdoor installations Small and compact size Cooling by free air convection 100% full load burn-in test High reliability,low cost Suitable for Damp / wet locations Suitable for LED lighting and moving sign applications 2 years warranty
F
110
M
M
SPECIFICATION
MODEL DC VOLTAGE PLN-20-12 12V LED OPERATION VOLTAGE Note.5 9 ~ 12V 1.6A RATED CURRENT CURRENT RANGE CURRENT ADJ. RANGE RATED POWER OUTPUT VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP TIME VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR INPUT EFFICIENCY(Typ.) AC CURRENT INRUSH CURRENT(max.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE
Note.5
SELV
IP64
PLN-20-36 36V 27 ~ 36V 0.55A 0 ~ 0.55A 19.8W 3.0Vp-p PLN-20-48 48V 36 ~ 48V 0.42A 0 ~ 0.42A 20.2W 3.8Vp-p
PLN-20-18 18V 13.5 ~ 18V 1.1A 0 ~ 1.1A 19.8W 3.0Vp-p
PLN-20-24 24V 18 ~ 24V 0.8A 0 ~ 0.8A 19.2W 3.0Vp-p
0 ~ 1.6A 75% ~ 100% 19.2W 10% 3.0% 10%
RIPPLE & NOISE (max.) Note.2 2.5Vp-p
2300ms / 230VAC 3000ms / 115VAC at full load
Note.4 90 ~ 277VAC
127~392VDC
47 ~ 63Hz PF 0.9 at 75~100% load, 115VAC/230VAC 80% 81% 0.4A/115VAC 40A/230VAC 0.5mA / 240VAC 95 ~ 110% Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed. 27 ~ 34V 14 ~ 16V 19 ~ 22V Protection type : Shut off o/p voltage, clamping by zener diode 41 ~ 46V 54 ~ 60V 0.2A/230VAC 82% 83% 83.5%
110 10 (TSW1) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -30 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +80 , 10 ~ 95% RH 0.06%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes IEC61347-1, IEC61347-2-13, TUV EN61347-1, EN61347-2-13, UL8750, IP64 approved
I/P-O/P:3.75KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms/500VDC / 25 / 70%RH Compliance to EN55015 EMC EMI CONDUCTION & RADIATION Compliance to EN61000-3-2 Class C( 75% load);EN61000-3-3 HARMONIC CURRENT Compliance to EN61000-4-2,3,4,5,6,8,11;EN61547, light industry level, criteria A EMS IMMUNITY MTBF OTHERS DIMENSION PACKING
NOTE
643.6Khrs min.
MIL-HDBK-217F (25
)
148.5*38.5*28mm (L*W*H) 0.18Kg; 60pcs/12.8Kg/0.9CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage, please check the static characteristic for more details. 5. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
File Name:PLN-20-SPEC 2010-07-30
20W Single Output LED Power Supply
Mechanical Specification
PLN-20
Case No.989B
series
Unit:mm
148.5 3.2
10
2-R2.0
320 10 +V(Red) -V(Black)
AC/L(Brown) AC/N(Blue)
38.5
320 10
18AWG 2C
18.83
10.75
3.2
10
18AWG 2C
Block Diagram
I/P EMI FILTER & RECTIFIERS POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. DETECTION CIRCUIT
O.L.P.
PWM & PFC CONTROL
O.V.P. O.T.P.
Derating Curve
Static Characteristics
Ta:25
100
100 90
80
80 70
60
LOAD LOAD (%)
40
LOAD (%)
60 50 40
20
-30
-25
-5
0
15
30
40
50
60 (HORIZONTAL)
90
100
125
135
145
155 165
175
180
200
230
277
AMBIENT TEMPERATURE (
)
INPUT VOLTAGE (V) 60Hz
File Name:PLN-20-SPEC 2010-07-30
28
20W Single Output LED Power Supply
Power Factor Characteristic
Power factor will be higher than 0.9 when output loading is 75% or higher.
PLN-20
series
Constant Current Mode
1.00 0.98 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.78 50% 60% 70% 80% 90% 100%
PF
230VAC 110VAC
LOAD
EFFICIENCY vs LOAD (48V Model)
P LN-20 series possess superior working efficiency that up to 83.5% can be reached in field applications.
90 88 86 84 82 80 78 76 74 72 70 68 66 64 62 60 58 56 54 52 50 48 46 44 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
EFFICIENCY (%)
230VAC 110VAC
DRIVING METHODS OF LED MODULE
There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)].
100
(B) Constant Current area (A) Constant Voltage area
50 (max.) (C) Hiccup Protection 50 95 Io (%)
Vo(%)
Typical LED power supply I-V curve
File Name:PLN-20-SPEC 2010-07-30
很抱歉,暂时无法提供与“PLN-20-36”相匹配的价格&库存,您可以联系我们找货
免费人工找货