PLN-30-15

30W Single Output LED Power Supply Features : PLN-30 series Universal AC input / Full range (up to 295VAC) Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection Built-in constant current limiting circuit with adjustable OCP level Fully isolated plastic case with IP64 level Built-in active PFC function IP64 design for indoor or outdoor installations Pass LPS Class power unit, no FG Class 2 power unit 100% full load burn-in test High reliability Suitable for LED lighting and moving sign applications (Note.2) Compliance to worldwide safety regulations for lighting 2 years warranty F 110 M M SELV LPS ( except for 48V ) ( for 48V only) ( except for 48V ) IP64 PLN-30-36 36V 25.2 ~ 36V 0.84A 0 ~ 0.84A 30.24W 4.5Vp-p PLN-30-48 48V 33.6 ~ 48V 0.63A 0 ~ 0.63A 30.24W 3.7Vp-p SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT PLN-30-9 9V 3.3A 0 ~ 3.3A 29.7W CONSTANT CURRENT REGION Note.6 6.3 ~ 9V PLN-30-12 12V 8.4 ~ 12V 2.5A 0 ~ 2.5A 30W 2Vp-p PLN-30-15 15V 10.5 ~ 15V 2A 0 ~ 2A 30W 2.6Vp-p PLN-30-20 20V 14 ~ 20V 1.5A 0 ~ 1.5A 30W 2.6Vp-p PLN-30-24 24V 16.8 ~ 24V 1.25A 0 ~ 1.25A 30W 2.6Vp-p PLN-30-27 27V 18.9 ~ 27V 1.12A 0 ~ 1.12A 30.24W 2.3Vp-p RIPPLE & NOISE (max.) Note.2 2.6Vp-p VOLTAGE ADJ. RANGE Note.5 -5% ~ 10%. Can be adjusted by internal potentiometer SVR1 CURRENT ADJ. RANGE Note.5 3% ~ -25%. Can be adjusted by internal potentiometer SVR2 VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP TIME VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) 10% 3.0% 5.0% 2000ms / 230VAC 3000ms / 115VAC at full load Note.4 90 ~ 295VAC 127 ~ 417VDC 47 ~ 63Hz PF>0.95/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve) 80% 0.4A/115VAC 40A/230VAC 70% load) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level, criteria B 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. Output voltage can be adjusted through the SVR1 on the PCB; limit of output constant current level can be adjusted through the SVR2 on the PCB. 6. Constant current operation region is within 70% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 8. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. File Name:PLN-30-SPEC 2012-03-12 30W Single Output LED Power Supply Mechanical Specification 145 4.38 9.83 PLN-30 Case No.964A series Unit:mm 2-R2.25 23.5 320 20 61 320 20 47 AC/L(Brown) AC/N(Blue) +V(Red) -V(Black) 9.83 T case SVT 18AWG 2C SVT 18AWG 2C 4.38 T case: Max. Case Temperature. Output voltage and current adjustment : remove the upper case and adjust through SVR1 & SVR2 shown in the diagram. SVR1 SVR2 SVR1 Output voltage adjustment SVR2 Output current adjustment Block Diagram I/P EMI FILTER & RECTIFIERS POWER SWITCHING RECTIFIERS & FILTER DETECTION CIRCUIT PWM & PFC CONTROL O.V.P. fosc : 39KHz(115VAC) 53KHz(230VAC) +V -V O.L.P. O.C.P. Derating Curve Static Characteristics 100 100 90 80 80 70 60 LOAD (%) 40 LOAD (%) 60 50 40 20 -30 -25 -5 0 15 30 40 50 60 90 100 125 135 145 155 165 175 180 200 230 295 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz File Name:PLN-30-SPEC 2012-03-12 30 30W Single Output LED Power Supply Power Factor Characteristic Constant Current Mode 1 0 0 0 0 0 0 0 0 0 0 0 .0 .9 .9 .9 .9 .9 .8 .8 .8 .8 .8 .7 0 8 6 4 2 0 8 6 4 2 0 8 50% 60% 70% 80% 90% 100% (30W) PLN-30 series 277V ac 230V ac 115V ac PF LOAD EFFICIENCY vs LOAD (48V Model) PLN-30 series possess superior working efficiency that up to 85.5% can be reached in field applications. 90 86 82 78 74 70 66 62 58 54 50 46 42 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD EFFICIENCY (%) 277Vac 230Vac 115Vac DRIVING METHODS OF LED MODULE This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs. 100 Constant Current area 70 (max.) Hiccup Protection 50 100 Io (%) Vo(%) Typical LED power supply I-V curve File Name:PLN-30-SPEC 2012-03-12