RHP-1UI-A

1600~8000W 1U Distributed Power/Charger System RHP-1U Rack System Rack Dimension * W * H L 365 * 440 * 44 (1U) 14.4 * 17.3 * 1.73 (1U) mm inch Bauar t gepruft Sicherheit egel ma ge od o s be wac g www. tuv.com ID 2000000000 ■ Features Universal AC input / Full range 1U profile 19” rack shelf, fitting five 1600W modules up to 8000W with active current sharing Output voltage and current programmable Support hot swap (hot plug) Built-in PMBus protocol (Optional CANBus protocol) ■ Applications Distributed power architecture system Wireless/telecommunication solution  Electric vehicle or marine charger station DC UPS or emergency backup  Wastewater treatment system  Electrolysis system 5 years warranty ■ Description RHP-1U rack power system and RHB-1U rack charger system are the complete solution for the power distribution utilizing the rack configuration with the 1U low profile. Starting with a single unit of 1600W, RCP-1600 is the front end rectifier (or, power supply) and RCB-1600 is the charger module. With the active current sharing function, up to 8000W is able to be provided by 1 stack of the 19 ” rack mountable shelf RHP-1U, with either rectifier or charger, and 24000W by 3 stacks with rectifier. ■ Model Encoding Rack Shelf: RHP-1U I -A Whole System: RHP-8K1U I -12 Communication protocol option Rack Shelf for 1600W unit I: AC Inlet (IEC320-C14) T: Terminal block Profile of the system Series name Communication protocol option Output voltage I: AC Inlet (IEC320-C14) T: Terminal block 8K: Maximum wattage with fully-populated shelf 1U: Profile of the system Series name Type Blank CAN Communication Protocol PMBus protocol CANBus protocol Note In Stock By request (RHP : Power supply system; RHB : Charger system) File Name:RHP-1U RACK SYSTEM-SPEC 2017- 09-12 RHP-1U Rack System 1600~8000W 1U Distributed Power/Charger System SPECIFICATION - Power Supply System MODEL OUTPUT RHP-8K1U -12 RHP-8K1U RECTIFIER RCP-1600-12 RACK SHELF RHP-1UI-A or RHP-1UT-A OUTPUT VOLTAGE MAX. OUTPUT CURRENT RHP-8K1U RCP-1600-24 RCP-1600-48 12V 24V 48V 625A 335A 167.5A 8040W 8040W MAX. OUTPUT POWER Note.5 7500W VOLTAGE RANGE -24 Note.6 90 ~ 264VAC -48 127 ~ 370VDC FREQUENCY RANGE INPUT 47 ~ 63Hz AC CURRENT (Typ.) per RECTIFIER 14A/115VAC LEAKAGE CURRENT per RECTIFIER 8A/230VAC 15A/115VAC 8.5A/230VAC 15A/115VAC 8.5A/230VAC 95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods (Note 4) EMC IMMUNITY OTHERS NOTE DIMENSION PACKING Rack 365*482.6*44(L*W*H, with mounting bracket) ; 365*440*44(L*W*H, without mounting bracket) 5.5Kg; 3pcs/17.5Kg/2.11CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. Under parallel operation of more than one rack connecting together, ripple of the output voltage may be higher than the SPEC at light load condition. It will go back to normal ripple level once the output load is more than 5%. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 1000mm*1300mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 5. Output of all the RCP-1600 modules are connected in parallel in the rack. 6. Derating may be needed under low input voltages. Please check the static characteristics for more details. 7. Because of component tolerance, there is a possibility that some of units connected in parallel will reach an overcurrent limit then overloading the other units when operating at full load condition. If overload conditions happen in parallel usage, it is suggested that derate the total output current by 10%. 8. The equivalent leakage current of the system is determined by the quantity of populated rectifiers. 9. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). File Name:RHP-1U RACK SYSTEM-SPEC 2017- 09-12 RHP-1U Rack System 1600~8000W 1U Distributed Power/Charger System SPECIFICATION - Charger System MODEL OUTPUT RHB-8K1U -12 CHARGER RCB-1600-12 RACK SHELF RHP-1UI-A or RHP-1UT-A -24 RHB-8K1U RCB-1600-24 RCB-1600-48 BOOST CHARGE VOLTAGE(Vboost)(default) 14.4V 28.8V 57.6V 13.8V 0 ~ 500A 90 ~ 264VAC 47 ~ 63Hz AC CURRENT (Typ.) per CHARGER 14A/115VAC 27.6V 0 ~ 275A 55.2V 0 ~137.5A FLOAT CHARGE VOLTAGE(Vfloat)(default) CURRENT RANGE Note.2 VOLTAGE RANGE FREQUENCY RANGE INPUT RHB-8K1U LEAKAGE CURRENT per CHARGER -48 127 ~ 370VDC 8A/230VAC 15A/115VAC 8.5A/230VAC 15A/115VAC 8.5A/230VAC