RPS-160

160W Single Output Medical Type Features : RPS-160 Universal AC input / Full range Built-in active PFC function series Protections: Short circuit / Overload / Over voltage / Over temperature 5"x3" compact size Free air convection for 110W and 160W with 20.5 CFM forced air With power good and fail signal output Built-in remote sense function for 5~15V No load power consumption under 0.75W by PS-ON control (G model) Standby 5V@0.8A with fan, @0.6A without fan (G model) 3 years warranty RPS G G: With 5Vsb & no load power consumption < 0.75 W Blank: Basic function (without 5Vsb) 160 12 EN60601-1 IEC60601-1 SPECIFICATION MODEL DC VOLTAGE RPS -160-5 5V RATED CURRENT (20.5CFM) 30A CURRENT RANGE (convection) 0 ~ 20A CURRENT RANGE (20.5CFM) 0 ~ 30A RATED POWER (convection) Note.7 103W RATED POWER (20.5CFM) Note.8 155W OUTPUT RIPPLE & NOISE (max.) Note.2 100mVp-p VOLTAGE ADJ. RANGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD OVER VOLTAGE PROTECTION OVER TEMPERATURE CH1:4.5 ~ 5.5V VOLTAGE TOLERANCE Note.3 4.0% 0.5% 1.0% 1800ms, 30ms/230VAC Note.6 90 ~ 264VAC RPS -160-12 12V 12.9A 0 ~ 9.1A 0 ~ 12.9A 112.2W 159.8W 100mVp-p CH1:10.8 ~ 13.2V 3.0% 0.5% 1.0% RPS -160-15 15V 10.3A 0 ~ 7.3A 0 ~ 10.3A 112.5W 159.5W 120mVp-p CH1:13.5 ~ 16.5V 3.0% 0.5% 1.0% RPS -160-24 24V 6.5A 0 ~ 4.6A 0 ~ 6.5A 113.4W 161W 150mVp-p CH1:22 ~ 27V 2.0% 0.5% 1.0% RPS -160-48 48V 3.25A 0 ~ 2.3A 0 ~ 3.25A 113.4W 161W 250mVp-p CH1:43.2 ~ 52.8V 2.0% 0.5% 1.0% 3500ms, 30ms/115VAC at full load 16ms/230VAC/115VAC at full load 127 ~ 370VDC PF>0.98/115VAC at full load 87% 87% 87% 88% 47 ~ 63Hz PF>0.93/230VAC 85% 2A/115VAC 1.1A/230VAC COLD START 35A/115VAC 70A/230VAC Earth leakage current 1ms POWER GOOD / POWER FAIL 500ms>PG>10ms 5 ~ 15V REMOTE SENSE -20 ~ +70 (Refer to "Derating Curve") WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION 20 ~ 90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60601-1, TUV EN60601-1 approved I/P-O/P:4KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A 230.5Khrs min. MIL-HDBK-217F (25 ) 127*76.2*34.6mm (L*W*H) 0.32Kg; 36pcs/12.5Kg/0.79CUFT EMC IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 5. HS1,HS2 & HS3 can not be shorted. 6. Derating may be needed under low input voltages. Please check the derating curve for more details. 7. The rated power includes 5Vsb @ 0.6A. 8. The rated power includes 5Vsb @ 0.8A. 160W Single Output Medical Type Mechanical Specification FAN 20.5CFM min. 5 RPS-160 series Unit:mm AC Input Connector (CN1) : JST B3P-VH or equivalent Pin No. 1 2 3 Assignment AC/L No Pin AC/N 5cm Mating Housing JST VHR or equivalent Terminal JST SVH-21T-P1.1 or equivalent SVR1 CN3 HS1 1 2 3 4 DC Output Connector (CN2) : JST B8P-VH or equivalent 1 2 3 4 5 6 7 8 76.2 66.2 FS1 CN1 FS2 1 2 3 HS2 Pin No. 1,2,3,4 5,6,7,8 Assignment +V -V Mating Housing JST VHR or equivalent Terminal JST SVH-21T-P1.1 or equivalent HS3 CN2 CN901 LED Power Good Connector(CN3):JST B4B-XH or equivalent Pin No. CN901 Status PG GND -S +S Mating Housing JST XHP or equivalent Terminal JST SXH-001T-P0.6 or equivalent 4- 5 117 127 3.5 1234 1 2 3 4 5VSB Connector(CN901) : JST B-XH or equivalent PS/ON 5mA(max.) 34.6 GND Pin No. 1 2,4 3 Assignment PS/ON GND 5VSB Mating Housing JST XHP or equivalent Terminal JST SXH-001T or equivalent HS1,HS2,HS3 can not be shorted 3 max. Block Diagram +5VSB DETECTION CIRCUIT fosc :100KHz(5V) 70KHz(12~48V) +5VSB +S POWER SWITCHING PWM CONTROL I/P EMI FILTER RECTIFIERS & PFC POWER SWITCHING RECTIFIERS & FILTER RECTIFIERS & FILTER PG +V -V -S PG FG O.L.P. CONTROL DETECTION CIRCUIT O.V.P. PS/ON CONTROL PS/ON Derating Curve Output Derating VS Input Voltage Ta=25 100 100 With FAN 90 80 70 80 60 LOAD (%) LOAD (%) 60 70 (HORIZONTAL) Without FAN 40 60 50 40 20 -20 0 10 20 30 40 50 90 95 100 115 120 140 160 180 200 220 240 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name:RPS-160-SPEC 2011-07-05