SCP-2K4

2400W Parallel (N+1) With PFC Function SCP-2K4 series ■ Features : AC input 180~260VAC, 3ψ3 wire AC 220V, 1ψor 380V, 3ψ4 wire(option) PF> 0.98@ 230VAC Protections: Short circuit / Overload / Over voltage / Over temperature Built-in remote sense function, remote ON-OFF control Built-in power good signal output Built-in parallel operation function(N+1) Can adjust from 20~100% output voltage by external control 1-5V Forced air cooling by built-in DC fan Case coating with paint 3 years warranty .. SPECIFICATION ORDER NO. SAFETY MODEL NO. DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE LINE REGULATION LOAD REGULATION VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR INPUT EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT (max.) LEAKAGE CURRENT(max.) OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE Note. 4 SCP-2K4-09 2K4S-P009 9V 266A 0 ~ 266A 2394W SCP-2K4-12 2K4S-P012 12V 200A 0 ~ 200A 2400W 120mVp-p SCP-2K4-15 2K4S-P015 15V 160A 0 ~ 160A 2400W 150mVp-p SCP-2K4-18 2K4S-P018 18V 133.3A 0 ~ 133.3A 2399W 150mVp-p SCP-2K4-24 2K4S-P024 24V 100A 0 ~ 100A 2400W 150mVp-p SCP-2K4-36 2K4S-P036 36V 66.6A 0 ~ 66.6A 2397W 200mVp-p SCP-2K4-48 2K4S-P048 48V 50A 0 ~ 50A 2400W 200mVp-p SCP-2K4-60 2K4S-P060 60V 40A 0 ~ 40A 2400W 200mVp-p ± 1.0% ± 0.5% ± 0.5% RIPPLE & NOISE (max.) Note.2 90mVp-p ± 3.0% Typical adjustment by potentiometer ± 1.0% ± 1.0% VOLTAGE TOLERANCE Note.3 ± 2.0% ± 0.5% ± 1.5% 180 ~ 260VAC 47 ~ 63Hz >0.98 / 230VAC 83% 15A / 230VAC 60A / 230VAC 3.5mA / 240VAC 110 ~ 140% rated output power 84% 85% ± 0.5% ± 0.5% ± 0.5% ± 0.5% 20% ~ 100% adjustment by 1 ~ 5VDC external control ± 1.0% ± 1.0% ± 1.0% ± 1.0% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% ± 0.5% SETUP, RISE, HOLD UP TIME 800ms, 400ms, 12ms at full load 3ψ3 wire (other system available) 86% 88% 88% 89% 89% Protection type : Current limiting, delay shut down o/p voltage, re-power on to recover 110 ~ 135% Follow to output set up point Protection type : Shut down o/p voltage, re-power on to recover >100℃ / measure by heat sink, near transformer Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -20 ~ +65℃ (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85℃, 10 ~ 95% RH ± 0.04% / ℃ (0 ~ 50℃) 10 ~ 200Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, OP/FG:100M Ohms / 500VDC / 25℃/ 70% RH EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) class A EMC (Note. 5) Compliance to EN61000-3-2,3 HARMONIC CURRENT EMS IMMUNITY POWER GOOD SIGNAL SPECIAL FUNCTION OTHERS COOLING MTBF DIMENSION PACKING NOTE Compliance to EN61000-4-2,3,4,5,6,8,11, Light industry level, criteria A Open collector of NPN transistor DC Voltage Adj., Remote sensing, remote control, parallel operation(refer to control terminal instruction manual) By fan, >20% load or >50℃ fan on 24.9K hrs min. MIL-HDBK-217F(25℃) 350*212*124mm (L*W*H) 9.0kg ; 1pcs / 10kg / CARTON 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Current limiting 3 times(1.5s,3.0s,5.0s)Then intelligent auto recovery before shut down 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:SCP-2K4-SPEC 2007-03-01 2400W Parallel (N+1) With PFC Function Mechanical Specification SCP-2K4 series Unit:mm 212[8.35] 332 [13.07] 8-M3X0.5 Terminal Block For Control Signal 1 23 45678 V-ADJ 1 2 5-M4X0.7 Terminal block For AC Input 34 5 123.9 [4.88] Air flow direction 6-M6 SCREW FOR DC OUTPUT POS(+) LED 320 [12.60] 30 [1.18] NEG(-) 6 [0.24] TYP 180[7.09] 4-M4X0.7 MOUNTING HOLE FOR USER 290 [11.42] 24 [0.94] Control Terminal Pin. No. Assignment : Pin No. 1 2 3 4 Assignment VS+ VSVCI VCO Pin No. 5 6 7 8 Assignment PG PAR GND INH AC Input Terminal Pin. No. Assignment Pin No. 1 2 3 Assignment FG N T Pin No. 4 5 Assignment S R Derating Curve Ta=25℃ 100 80 OUTPUT POWER (W) -10 10 20 30 40 50 60 70 2400 2000 LOAD (%) 60 40 1200 20 900 -20 90 110 150 170 260 AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (VAC) 60Hz File Name:SCP-2K4-SPEC 2007-03-01 2400W Parallel (N+1) With PFC Function Control terminal instruction manual SCP-2K4 series LOAD LOAD LOAD LOAD VS+ VSVCI VCO PG PAR GND INH VS+ VSVCI VCO PG PAR GND INH VS+ VSVCI VCO PG PAR GND INH ON/OFF SWITCH VS+ VSVCI VCO PG PAR GND INH H:ON L:OFF USING INTERNAL VOLTAGE CONTROL REMOTE SENSING ON/OFF CONTROL BY SWITCH ON/OFF CONTROL BY TRANSISTOR Vout GOOD FAIL : LED OFF : LED ON O.V.P. 120% (Typ.) 120 100 LOAD LOAD OUTPUT VOLTAGE (%) 80 60 40 20 Non-Linear VS+ VSVCI VCO PG PAR GND INH 40V / 0.5A MAX. VS+ VSVCI VCO PG PAR GND INH DC 1-5V POWER GOOD SIGNAL OUTPUT VOLTAGE ADJUST WITH DC 1-5V 1 2 3 4 5 6 V EXTERNAL VOLTAGE (DC) LOAD LOAD VS+ VSVCI VCO PG PAR GND INH VS+ VSVCI VCO PG PAR GND INH VS+ VSVCI VCO PG PAR GND INH VS+ VSVCI VCO PG PAR GND INH VS+ VSVCI VCO PG PAR GND INH VS+ VSVCI VCO PG PAR GND INH PARALLEL OPERATION WITH REMOTE SENSING PARALLEL OPERATION WITHOUT REMOTE SENSING F ile Name:SCP-2K4-SPEC 2007-03-01 2400W Parallel (N+1) With PFC Function FIG. A: 3 3W 220VAC SYSTEM (STANDARD MODEL FOR STOCK) R R SCP-2K4 series L1 N1 FG1 220V S L2 N2 FG2 T S N (NC) L3 N3 FG3 220V FG T FIG. B: 1 220VAC SYSTEM L R L1 N1 S FG1 220V L2 N2 FG2 T N L3 N3 FG3 N FG FIG. C: 3 4W 220/380VAC SYSTEM R R L1 N1 FG1 220V S L2 N2 FG2 T N N S FG L3 N3 FG3 380V T FIG. D: 3 4W 190/110VAC SYSTEM R R L1 N1 S N (N.C.) T L2 N2 L3 N3 N (NC) 110V FG1 FG2 FG3 S 190V FG T File Name: SCP-2K4-SPEC 2007-03-01