SD-15B-05

15W Single Output DC-DC Converter S D - 1 5 series Features : 2:1 wide input range Protections:Short circuit/Over load /voltage Built-in EMI filter,low ripple noise 100% full load burn-in test Low cost High reliability 1 year warranty SPECIFICATION MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE OUTPUT RATED POWER RIPPLE & NOISE (max.) Note.2 VOLTAGE ADJ.RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE ,HOLD UP TIME VOLTAGE RANGE INPUT EFFICIENCY(Typ.) DC CURRENT(Typ.) OVER LOAD PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC WITHSTAND VOLTAGE ISOLATION RESISTANCE 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min.each along X, Y, Z axes I/P-O/P:2KVAC I/P-FG:1KVAC O/P-FG:0.5KVAC I/P-O/P,I/P-FG,O/P-FG:100M Ohms/500VDC SD-15A-05 5V 3A 0 ~ 3A 15W 100mVp-p 4.75~5.5VDC 2.0% 0.5% 0.5% SD-15B-05 SD-15C-05 SD-15A-12 12V 1.25A 0 ~ 1.25A 15W 120mVp-p 10.8~13.2VDC 1.0% 0.3% SD-15B-12 SD-15C-12 SD-15A-24 24V 0.625A 0 ~ 0.625A 15W 150mVp-p 21.6~26.4VDC 1.0% 0.2% 0.2% SD-15B-24 SD-15C-24 0.3% 2.5s, 25ms,--- 12VDC/24VDC/48VDC at full load A: 9.2 ~18VDC B:18 ~ 36VDC 68% 76% 75% 1.9A/12VDC 0.9A/24VDC 105% -160% rated output power C:36~72VDC 76% 72% 0.45A/48VDC 79% 70% 77% 78% Protection type : hiccup mode , recovers automatically after fault condition is removed 13.8~ 16.2V 5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover -10 60 ¡ 27.6 ~ 32.4V 20 ~ 90% RH non-condensing EMI CONDUCTION&RADIATION Compliance to EN55022(CISPR22) CLASS B Compliance to EN61000-4-2,3,4,6,8;ENV50204,EN55024,light industry level,criteria A EMS IMMUNITY DIMENSION PACKING 79*51*28mm (L*W*H) 0.18kg,60 PCS/11.8kg OTHERS NOTE 1. All parameters NOT specially mentioned are measured at normal input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:SD-15 SPEC.2006-04-19 15W Single Output DC-DC Converter Mechanical Specification 1 2 3 6 .6 2 4 5 +V ADJ. LED 2-M3 L=4 S D - 1 5 series C ase No.931 Unit:mm 7.62 55 79 10.5 Terminal Pin. No Assignment Pin No. 1 2 3 Assignment DC INPUT V+ DC INPUT VFG Pin No. 4 5 Assignment DC OUTPUT +V DC OUTPUT -V 14 66.5 2.25 2-M3 L=6 28 Block Diagram RECTIFIERS & FILTER POWER SWITCHING RECTIFIERS & FILTER 25.4 fosc : 96KHz 51 I/P EMI FILTER +V -V OLP PWM CONTROL DETECTION CIRCUIT Output Derating Static Characteristics Ta=25 100 SD-15A 100 SD-15B SD-15C 80 80 60 60 LOAD (%) 40 LOAD (%) 0 10 20 30 40 50 45 60 55 (HORIZONTAL) (VERTICAL) 40 20 20 -10 -10 9.2 18 36 72 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE( VDC ) File Name:SD-15 SPEC.2006-04-19