MLX81108KDC-CAA-000-TU

MLX81106/7/8/9 Micro/Mini LIN Slave Controller Features Application Controller o Internal RC-Oscillator (12..24 Mhz programmable) o 16-bit RISC MCU with 24kB..32kB User Flash, 1kByte RAM, 384 Byte EEPROM with ECC LIN Protocol Controller according to LIN 2.x and SAE J2602 o Baudrate up to 19.2 kBaud o Frame processing o Low interrupt load to the application LIN Transceiver according to LIN 2.x and SAE J2602 o Support for Autoconfig according bus shunt IO Configuration o o o o o o o o o o Up to 12 IOs (MLX81107/9) or 4 IOs (MLX81106/8) 4 programmable constant current (max 30mA)/high voltage capable IOs 4 times 16-bit PWM outputs Interrupt capable Inputs 10-bit ADC with integrated pre-divider connected to all IOs, Battery and LED threshold voltage monitor via ADC o can be used for aging and temperature compensation of LEDs Integrated temperature sensor for thermal management Configurable Wake up sources (LIN and IOs) Serial Interface (SPI) Voltage output for supply external 5V loads via npn transistor (MLX81107) Voltage Regulator o Low standby current consumption of typ 25µA (max 30 µA) in sleep mode o Over-temperature shutdown, 40V load dump protected Other Features o Automotive Temperature Range of –40°C to 125°C o MLX81106/8 – Thermally enhanced SOIC8 Package o MLX81107/9 – QFN5x5 20 pins Short Description This IC is a fully integrated low end LIN Slave for switch and PWM applications in automotive environment. It is suitable for bus systems according to LIN 2.x as well as SAE J2602. The combination of physical layer LIN transceiver and LIN protocol controller in combination with easy to configure switch inputs and PWM outputs make it possible to develop in a short timeframe simple, but powerful and cheap switch slave nodes for LIN Bus systems. MLX81106/7/8/9 – Short Datasheet Page 1 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller Contents 1. General Overview .................................................................................................................................... 3 1.1 1.2 2. Electrical Characteristics ....................................................................................................................... 4 2.1 2.2 3. Absolute Maximum Ratings.............................................................................................................. 4 Operating Conditions ........................................................................................................................ 5 Functional Description ........................................................................................................................... 6 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4. Memory Configuration ...................................................................................................................... 3 Block Diagram .................................................................................................................................. 3 MCU ................................................................................................................................................. 6 LIN Transceiver and Controller ........................................................................................................ 6 Memory............................................................................................................................................. 6 HV0..3 IO .......................................................................................................................................... 6 LV0..7 IO (MLX81107/9 only) ........................................................................................................... 6 Software Debug Interface................................................................................................................. 6 ADC .................................................................................................................................................. 7 PWM ................................................................................................................................................. 7 Power Supply ................................................................................................................................... 7 Application Hints .................................................................................................................................... 8 4.1 4.2 4.3 General Application Examples MLX81106/8.................................................................................... 8 LIN RGB Application Examples MLX81106/8 .................................................................................. 9 Application Examples MLX81107/9 ............................................................................................... 10 5. Soldering information ........................................................................................................................... 11 6. Disclaimer .............................................................................................................................................. 11 MLX81106/7/8/9 – Short Datasheet Page 2 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 1. General Overview 1.1 Memory Configuration Part Flash User EEPROM RAM Package MLX81106 24kByte 384Byte 1kByte SOIC8 MLX81107 24kByte 384Byte 1kByte QFN 5x5 MLX81108 32kByte 384Byte 1kByte SOIC8 MLX81109 32Kbyte 384Byte 1kByte QFN 5x5 1.2 Block Diagram Power Supply VS VDDD VDDA UVLO Aux Supply + WakeUp Logic ADCx POR SPI INTx HV0 HV1 LV0 WakeUp LIN WakeUp LVx WakeUp HVx HVDIN HVINEN Uref (LV7 only) 5.6V/2mA 35mA HVDOUTB PWMx Out SPI Out LIN Dig TX HV2 HV3 LV6 / HV3 LV5 / HV2 ADCx ... ADCVS LV3 SPI LV4 INTx LV5 MISO SPI SCLK LV3 / HV0 SS ... PWM4 ... 0 LV6 LVDIN LVINEN LV7 LVDOUTB PWMx Out SPI Out LIN Dig TX ... ADC Divider and Mux 16-bit PWM LV2 ADCx MOSI LV4 / HV1 LV1 81107/9 only Test/Debug Interface GND INT LIN Autoconfig LIN _OUT RC-Osc. 10-bit ADC Window WD Timer Max 32kbyte Flash LIN Controller MULAN MCU 1kbyte RAM to ADC MUX LIN PHY LIN_IN 384byte EEPROM Figure 1 - Block Diagram MLX81106/7/8/9 – Short Datasheet Page 3 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 2. Electrical Characteristics All voltages are referenced to ground (GND). Positive currents flow into the IC. 2.1 Absolute Maximum Ratings In accordance with the Absolute Maximum Rating System (IEC60134). The absolute maximum ratings given in the table below are limiting values that do not lead to a permanent damage of the device but exceeding any of these limits may do so. Long term exposure to limiting values may affect the reliability of the device. Reliable operation is only specified within the limits shown in „Operating conditions”. Parameter Symbol Battery Supply Voltage Short term supply voltage Transients at supply voltage Transients at supply voltage Transients at high voltage signal pins Transients at high voltage signal pins Transient at high voltage signal and power supply pins DC voltage on LIN, HVx DC voltage on D0..7 VS VS_ld VS_tr1 VS_tr2 VLINx_tr1 VLINx_tr2 VHV_tr3 VLIN_DC Vlogic_DC VESDIEC VESDHBM ESD voltage VESDCDM VESDMM Maximum latch – up free current at any pin Storage temperature Junction temperature Condition ISO 7637/2 pulse 5; t < 400 ms ISO 7637/2 pulse 1[1] ISO 7637/2 pulses 2 [1] ISO 7637/3 pulse 1 [2] ISO 7637/3 pulses 2 [2] ISO 7637/2 pulses 3A, 3B [3] T2uF blocking capacitor. ISO 7637/3 test pulses are applied to LIN via a coupling capacitance of 100nF. ISO 7637/3 test pulses are applied to LIN via a coupling capacitance of 1nF. ISO 7637/2 test pulses are applied to VS via a reverse polarity diode and >2uF blocking capacitor. Equivalent to discharging a 100pF capacitor through a 1.5kΩ resistor conforms to MIL STD 883 method 3015.7. MLX81106/7/8/9 – Short Datasheet Page 4 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 2.2 Operating Conditions Parameter Symbol Min Max Unit VS VS_S Tamb 5.5 18 -40 18 27 +125 V V °C Battery supply voltage High battery supply voltage Operating ambient temperature [1] Table 2 - Operating Conditions 1) Vs is the IC supply voltage including voltage drop of reverse battery protection diode, V DROP = 0.4…1V, VBAT_ECU = 6…27V. MLX81106/7/8/9 – Short Datasheet Page 5 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 3. Functional Description 3.1 MCU  16-bit RISC MCU 3.2 LIN Transceiver and Controller   Support for LIN 2.x and J2602 Support Autoconfig according bus shunt 3.3 Memory      24kByte User Flash MLX81106/7 32kByte User Flash MLX81108/9 1kByte RAM 384Byte User EEPROM 128byte MLX EEPROM for LIN IDs, Calibration data 3.4 HV0..3 IO           High voltage capable open drain output (max 60Ohm RDSON) High voltage capable constant current output of max. 30mA per IO (max. 48mA short term) 16-bit PWM Output Digital output (5V) High voltage capable input Digital (5V) input 10-bit ADC Input inc.pre-devider for direct measurement of VS Differential SC-Amplifier for detection of very small voltage changes for LED threshold measurement SPI Interface Interrupt capable input 3.5 LV0..7 IO (MLX81107/9 only)         Open drain output (3mA) PWM output Low voltage output (5V) Low voltage (5V) input ADC Input inc. pre-devider for direct measurement SPI Interface Interrupt capable input LV7 - Voltage output for supply external 5V loads via npn transistor (See appl example for details) 3.6 Software Debug Interface     Available at HV0..3pins (MLX81106/8) Available at LV0..3pins (MLX81107/9) HV2(MLX81106/8) and LV2(MLX81107/9) needs pull up against 3.3V supplied from emulator For full debug function on 81106/8 the MLX81107/9 can be used as software development device. MLX81106/7/8/9 – Short Datasheet Page 6 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 3.7 ADC     10-bit ADC Up to 20 channels (HVO..3, LV0..7,VS, internal references, temp sensor) Full Scale 5V via internal pre-divider Continuous Mode: Automatic measuring of enabled channels. Result stored via DMA. If new result available old will be overwritten 3.8 PWM       Max 16-bit resolution, min 370Hz Configurable from 8-bit to 16-bit, 8-bit mode with max possible frequency – approx 60kHz 4 undependent PWM channels Programmable PWM frequenz per channel Programmable interrupt generation at the beginning and/or end of every PWM period Synchronuous switch of duty cycle change 3.9 Power Supply   Internal compensated Primary Cap min 2.2uF MLX81106/7/8/9 – Short Datasheet Page 7 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 4. Application Hints 4.1 General Application Examples MLX81106/8 VBat 2.2µF VS VS 47nF VS HV2 ... HV0 MLX81106 VS HV1 VS LIN_IN 180p LIN_OUT HV3 GND Figure 2 - Application schematic sample MLX81106/7/8/9 – Short Datasheet Page 8 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 4.2 LIN RGB Application Examples MLX81106/8 VBat 2.2µF VS VS 47nF HV1 MLX81106 HV0 VS HV2 VS LIN_IN 180p LIN_OUT HV3 If no autoconfig is necessary LIN_OUT must be open GND Figure 3 - LIN RGB Slave MLX81106/7/8/9 – Short Datasheet Page 9 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 4.3 Application Examples MLX81107/9 VS VBat 2.2µF VS LV7 5V 5V out 47nF LV0 HV4 5V 5V LV1 VS 5V ... HV0 LV2 LV3 MLX81107 VS SS LV4 LV5 SCLK LV6 MOSI MISO SPI Interface 5V LVx HV1 VS HV2 LIN_IN 180p VS LIN_OUT GND HV3 Figure 4 - Application schematic sample MLX81106/7/8/9 – Short Datasheet Page 10 of 11 Oct 2014 Rev 017 MLX81106/7/8/9 Micro/Mini LIN Slave Controller 5. Soldering information Please see http://www.melexis.com/Assets/Soldering-Application-Note-and-Recommendations-5446.aspx 6. Disclaimer Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis’ rendering of technical or other services. © 2014 Melexis N.V. For the latest version of this document. Go to our website at www.melexis.com Or for additional information contact Melexis Direct: Europe and Japan: Phone: +32 1367 0495 E-mail: sales_europe@melexis.com All other locations: Phone: +1 603 223 2362 E-mail: sales_usa@melexis.com ISO/TS16949 and ISO14001 Certified MLX81106/7/8/9 – Short Datasheet Page 11 of 11 Oct 2014 Rev 017