MLX90109EDC-AAA-000-SP

MLX90109 125kHz RFID Transceiver Features and Benefits    Integrated RFID transceiver Adressing 100kHz to 150kHz frequency range transponder. Biphase and Manchester ASK. ON/OFF keying modulation. Low Power and high performances Unique Parallel Antenna concept for maximum power efficiency. Power down mode available. Baud rate selectable “on-chip” filtering for maximum sensitivity. No zero modulation problems. Low cost and compact design SO8 package and high level of integration for compact reader design. No external quartz reference required, only 2 resistors plus antenna. On chip decoding for fast system design and ease of use. Open drain data and clock outputs for 2-wire serial communication. Applications Examples     Car Immobilizers Portable readers Access control House held appliances Ordering Code Product Code MLX90109 MLX90109 MLX90109 MLX90109 Temperature Code E E C C Legend: Temperature Code: Package Code DC DC DC DC Package Code: Packing Form: E for Temperature Range -40°C to 85°C C for Temperature Range 0°C to 70°C DC for SOIC150Mil RE for Reel, TU for Tube Ordering example: MLX90109EDC-AAA-000-RE REVISION 011 - JUNE 19, 2017 3901090109 Option Code AAA-000 AAA-000 AAA-000 AAA-000 Packing Form Code RE TU RE TU MLX90109 125kHz RFID Transceiver 1. Functional diagram VDD VDD MLX90109 MODU RC modulation network (2) (1) COIL microcontroller (1): MODE/SPEED config settings (2): DATA/CLOCK outputs 2. Description The MLX90109 is a single chip RFID transceiver for the 125kHz frequency range. It has been conceived for minimum system cost and minimum power consumption, offering all required flexibility for a state of the art AM transceiver base station. An external coil (L), and capacitor (C) are connected as a parallel resonant circuit, that determines the carrier frequency and the oscillator frequency of the reader. This eliminates zero modulation effects by perfect antenna tuning, and avoids the need for an external oscillator. The reader IC can easily be switched to power down by setting the antenna amplitude to zero. The MLX90109 can be configured to decode the transponder signal on-chip. In this case the decoded signal is available through a 2-wire interface with clock and data. For minimum interface wiring, the non-decoded transponder signal can also be made available on a single wire interface. Page 2 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver Contents Features and Benefits................................................................................................................................ 1 Applications Examples ............................................................................................................................... 1 Ordering Code ........................................................................................................................................... 1 1. Functional diagram ................................................................................................................................ 2 2. Description ............................................................................................................................................ 2 3. Maximum ratings................................................................................................................................... 5 4. Pad definitions and descriptions ............................................................................................................ 5 5. MLX90109 Electrical Specifications........................................................................................................ 6 6. Block Diagram........................................................................................................................................ 7 7. General Description ............................................................................................................................... 7 7.1. Loop Gain Oscillator............................................................................................................................ 7 7.2. Peak Detector...................................................................................................................................... 7 7.3. Band-Pass Filter................................................................................................................................... 7 7.4. Digital demodulator ............................................................................................................................ 8 7.5. Antenna voltage definition ................................................................................................................. 8 7.6. Power Down mode ............................................................................................................................. 8 7.7. Write operation .................................................................................................................................. 8 8. System design parameters..................................................................................................................... 9 8.1. Auto start-up condition ...................................................................................................................... 9 8.2. Antenna current .................................................................................................................................. 9 8.3. Antenna Impedance ......................................................................................................................... 10 9. Typical configuration: READ ONLY ....................................................................................................... 11 9.1. Application diagram .......................................................................................................................... 11 9.2. Absolute minimum schematic.......................................................................................................... 11 9.3. Power consumption.......................................................................................................................... 11 9.4. Noise cancellation ............................................................................................................................. 12 9.5. Integrated decoding ......................................................................................................................... 12 9.6. Close coupling ................................................................................................................................... 12 10. Typical configuration: READ/WRITE ON/OFF keying (FDX-B100) ........................................................ 13 10.1. Application diagram........................................................................................................................ 13 11. Standard information regarding manufacturability of Melexis products with different soldering processes............................................................................................................................................ 14 12. ESD Precautions................................................................................................................................. 14 Page 3 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 13. FAQ ................................................................................................................................................... 15 13.1. Is it possible to make proportional modulation (depth less than 100%) with the MLX90109? . 15 13.2. How should I read data information from a transponder up to 15cm? ...................................... 15 13.3. Is it possible to increase the output power of the MLX90109 transceiver? ............................... 15 13.4. Are there any specific coils available for the MLX90109 transceiver? ........................................ 15 13.5. What are the recommended pull-up values on DATA and CLOCK pins? ..................................... 15 14. Package Information.......................................................................................................................... 16 14.1. Plastic SO8 ....................................................................................................................................... 16 15. Contact .............................................................................................................................................. 17 16. Disclaimer .......................................................................................................................................... 17 Page 4 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 3. Maximum ratings Supply voltage (V DD with respect to V SS) Input voltage on any pin (except COIL, DATA and CLOCK) Input voltage on COIL, DATA and CLOCK Maximum junction temperature Symbol VDD Condition Min DC -0.3 Max 6 Unit Volts VIN -0.3 VDD+0.3 Volts Vclamp -0.3 15 Volts 150 ºC TJ Table 1: Absolute maximum ratings Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 4. Pad definitions and descriptions Pad Name COIL Function Oscillator output VSS Ground SPEED Data rate selection : 2kbaud or 4kbaud MODU Input for amplitude setting MODE Decoding mode selection : Biphase or Manchester CLOCK Clock output of decoder DATA Data output of decoder VDD Power Supply Table 2: Pin description MLX90109 Plastic SO8 Page 5 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 5. MLX90109 Electrical Specifications o o DC Operating Parameters TA = -40 C to 85 C, Fres = 125kHz, VDD = 3.1 to 5.5V Antenna parameters: Lant = 73.6uH, Qant =17.3, Zant=1k Parameter. Symbol Supply Voltage VDD Resonance Frequency Fres (Depends on the resonance frequency of the antenna) Frequency drift with temperature  Fres T) Vsens Fres = 125 kHz (Depends on the application) Sensitivity (note 1) Amplitude Offset (note 2) Power down voltage (on MODU pin) Power up voltage (on MODU pin) Power down Current Supply Current (excluding antenna supply current) (note 3) Antenna supply current (note 4) Leakage current on pins COIL, MODE, SPEED, MODE, DATA Vos Output voltage DATA and CLOCK pin Test Conditions Min Typ Max 3.1 100 5.5 V 150 kHz +1 % 10 30 mVpp 0.15 0.35 4.9 3.0 4.3 2.4 1.5 V μA 3.0 mA 125 -1 0 4.0 2.2 3.2 1.3 0 Units IDD,pn VDD=5V VDD=3.1V VDD=5V VDD=3.1V VMODU = VDD IDD VDD=5V, VMODU = 0.8V 1.8 IDD,ant (Depends on the application) 2.8 Ileak (Power down) 1.0 μA Vol Pull-up resistance Rpu > 2k 0.4 V Vpd Vpu V V mA Table 3: Electrical specifications Note 1: The sensitivity is defined as the minimum amplitude of the 2kHz- modulation, generated by the transponder, demodulated and decoded by the reader. This parameter depends on the application:  the value of VDD  the antenna  the code sent to the reader Note 3: The supply current of the device depends on the antenna drive current IDD,ant: Typically: IDD  1.3 mA + IDD,ant / 6.3 IDDant A IDD A Lant Cant COIL 1 VSS 2 3 MODU 4 8 VDD MLX90109 Note 2: The antenna amplitude voltage is: Vant = VDD – VMODU + Vos Supply voltage VDD 7 6 5 Note 4: The antenna supply current (called IDD,ant) is the equivalent DC supply current driven by the chip through the antenna. Page 6 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 6. Block Diagram VDD MLX90109 VDD Peak Detector COIL Band-pass Filter Comparator clock Loop Gain Oscillator Digital Decoder DATA CLOCK GND MODU SPEED MODE 7. General Description 7.1. Loop Gain Oscillator The oscillator frequency is locked on the antenna resonance frequency. The clock is derived from the oscillator. In this way, its characteristics are locked to the transmission frequency. As the antenna is used to determine the carrier frequency, the antenna is always perfectly tuned to resonance. Consequently the MLX90109 is not sensitive to zero modulation (the socalled “zero modulation” is the phenomena whereby the tag does modulate properly, but no amplitude modulation can be observed at the reader coil). 7.2. Peak Detector The peak detector of the transceiver detects the AM signal generated by the tag. This signal is filtered and amplified by an on-chip switched capacitor filter before feeding the digital decoder. The same signal is fed back to close the loop of the antenna voltage. 7.3. Band-Pass Filter By setting the SPEED pin to VDD or to GND, the filtering characteristics are optimized for either 2 or 4 kbaud. The MLX90109 makes an internal first-order filtering of the envelope that changes according to the setting of the SPEED pin, to fit the Biphase and Manchester data spectrum: 2kbaud (speed pin to VDD) : 4kbaud (speed pin to VSS) : 400Hz to 3.6kHz 800Hz to 7.2kHz Page 7 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 7.4. Digital demodulator The MODE pin allows to define whether the MLX90109 will issue directly the filtered data stream on the DATA pin (MODE floating), or decode it in Manchester (MODE = VDD) or Biphase (MODE = VSS). In these two decoding modes, the MLX90109 issues the tag data on the DATA pin at the rising edge of the clock, which is issued on the CLOCK pin. Both CLOCK and DATA are open drain outputs and require external pull-up resistors. VSS SPEED 4kBaud MODE Biphase (*) Internally strapped to VDD/2 FLOAT (*) No decoding VDD 2kBaud Manchester 7.5. Antenna voltage definition The MLX90109 is a reader IC working in a frequency range of 100 to 150kHz, and designed for use with a parallel L-C antenna. This concept requires significantly less current than traditional serial antennas, for building up the same magnetic field strength. The voltage on the MODU pin (VMODU) controls the amplitude of the antenna voltage Vant, as follows: (1) Vant  VDD  VMODU  VOS with VOS, the offset relative to the VMODU level. Note: In order to use the internal driver FET as an ideal current source, the voltage on the coil pin should remain higher than its saturation voltage (typically 0.5V) for a driver current (I driver) up to 14mA. As this offset can be as much as 300mV, VMODU should be higher than 0.8V for a correct operation. 7.6. Power Down mode By setting VMODU higher than Vpd (preferably to VDD) the MLX90109 goes in power down. The antenna voltage will fade to 0V. The MLX90109 powers up by pulling VMODU below Vpu. 7.7. Write operation A sequence of power up / power down periods sets the antenna voltage ON and OFF. This feature allows to simply make an ON/OFF-keying modulated signal to the transponder. Typically, VMODU is toggled between VDD and 0.8V. Antenna fade-out is related to the quality factor of the antenna (Q ant) and its start-up takes about 3 carrier periods. Refer to the section “Typical operating configurations” further in this document for more detailed information and practical hints. Page 8 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 8. System design parameters The antenna internal driver is switched on as soon as the antenna voltage V(COIL) drops below V DD (see graphical representation below). The MLX90109 will inject a current Idriver into the antenna to make its amplitude follow the voltage on the MODU pin. In order to make the antenna start swinging on the resonance frequency, the chip needs to provide a positive feedback loop. This loop requires a minimal voltage swing at the COIL pin in order to be operational (typically 100mVpp). Below this value, the MLX90109 may not be able to retrieve its clock. V(COIL) VDD VMODU VSS Idriver on Graph: Antenna voltage and Driver current during normal operation. VMODU=0.8V for VDD=5V. The dashed curve shows the antenna voltage when the reader has been powered down. The internal driver current is a square wave with a 45% duty cycle. 8.1. Auto start-up condition Pulling VMODU, at power on, from 5V to less than Vpu will set the internal driver FET on. Provided the voltage drop on the coil pin is large enough (as explained above), the feedback loop is closed and the oscillation will increase in amplitude. To obtain the required positive feedback to start-up the oscillation successfully, the antenna impedance Z ant should be larger than 1k. This is so called “auto start-up condition”. 8.2. Antenna current The MLX90109 is specified to drive a maximum 14mA antenna drive current (Idriver). The AC equivalent supply current (IDDant) can be calculated as: (2) I DDant  2   sin(   )  I driver  0.63  I driver with  the duty cycle which is typically 45%. The current that the MLX90109 can inject at each oscillation onto the total antenna current is therefore limited to 9mA. The actual antenna current that generates the magnetic field can be calculated as: (3) I ant  Qant  I DDant A typical coil quality factor (Qant) value is 23, resulting in antenna currents of about 100mA This current resonance of the parallel antenna allows to build very low power reader base stations, contrary to serial antenna based versions. Readers using a serial antenna can leverage their voltage resonance to drive bigger antenna’s for long distance reading up to 1m, whereas the MLX90109 is designed to drive antennas to obtain a reading distance of 1cm up to 15cm (6”) (depending on efficiency and dimensions). Page 9 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 8.3. Antenna Impedance The antenna impedance is an important system design parameter for the MLX90109. Vant I DDant Z ant  (4) The antenna impedance can also be calculated as: (5) with ωres = 2*Fres Z ant  Qant  res  Lant From (4) and (5): Qant  res  Lant  Vant I DDant => Qant  I DDant  Vant res  Lant Finally in comparison with the formula (2): I ant  (6) Vant  res  Lant From the formula above, it is clear that Qant has no influence on Iant. Increasing Qant is equivalent to reduce the antenna supply current IDDant, hence it reduces the overall current consumption. Using the previous formula (6), it is possible to define the proportionality between the total number of ampere-turns, generating the magnetic field and the inductance of the antenna (With Nant the number of turns of the antenna coil) : N ant  I ant  N ant  Vant res  Lant 1 N ant  I ant ~ (7) with Lant ~ N ant 2 Lant Hence, to generate a strong field, it is better to choose a low antenna inductance. Limitation to this is given by the minimal antenna impedance (Zant > 1k) and the Q that one can achieve for such an antenna: Lmin  (8) Z min Qant  res Remarks: Note for equation (4): Mind that in reality the strong coupling with the tag may drastically reduce the antenna impedance. Note for equation (5): Mind that the quality factor of the antenna (Q ant) result in the quality factor of the coil and the quality factor of the capacitance as: (9) Qant  Qcoil // Qcapacitan ce So, a capacitance with a low quality factor may also reduce the antenna impedance. Page 10 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 9. Typical configuration: READ ONLY 9.1. Application diagram The MLX90109 is a highly integrated reader IC. In the application schematic below, only two resistors to set V MODU are required, next to the antenna inductance and tune capacitor. Capacitors C1 and C D can be added for a better noise cancellation. VDD Microcontroller VDD CD=100nF C1 7 3 4 6 5 100k 8 2 100k 1 MLX 90109 100k L, C DATA CLOCK MODE 19k SPEED 9.2. Absolute minimum schematic The interface with the microcontroller can be realized with only one connection. In this case, the mode pin is left floating and the integrated decoding is not used. VDD Microcontroller VDD CD=100nF SPEED 8 2 7 3 DATA 6 CLOCK 5 MODE 19k 4 100k 1 MLX 90109 C1 100k L, C 9.3. Power consumption If the power consumption is not critical and the reader does not have to be put in power down, the MODU voltage can be strapped to the required level (between 0.8V and V pd). However, the power consumption can be reduced by controlling the voltage on VMODU pin (e.g. with an IO port of a microcontroller). Page 11 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 9.4. Noise cancellation The read performance of a reader is linked with its robustness versus noise. The IC design has been optimized to get a high signal-to-noise ratio (SNR). The resonant antenna is a natural band-pass filter, which becomes more effective as its quality factor Qr increases. Noise rejection could also be improved by a careful PCB design, and by adding decoupling capacitor(s) on the supply lines. The most sensitive pins to noise injection are MODU and V DD. Since they directly determine Vant, the noise could be considered as an amplitude modulation (AM) data from a transponder. If the noise on both pins were identical, it would cancel out, giving a very noise-insensitive reader. Adding a capacitor C1 between MODU and VDD, together with R1 and R2 yields a high pass filter with a cut-off frequency at: Fcut  off  1 2    ( R1 // R2 )  C1 Typically, such a filter should short all noise in the data spectrum, but for many cases, it might be beneficial to set it to less than the net frequencies (50Hz, 60Hz). For example: R1=100k, R2=19k (to set VMODU), and C1=220nF gives a cut off frequency of 45Hz. 9.5. Integrated decoding The MLX90109 provides the option to have a decoded output. This significantly reduces the complexity of the microcontroller software. The data is available when the output clock signal is high. The clock signal has a 50% duty cycle when the data is valid. When the noise level is stronger than the signal level, for instance when no tag is present in the reader field, the duty cycle will be random. The microcontroller can use this feature to detect the presence of a tag: in that case, it must allow some asymmetry on the clock. As the sampling error may be 4μs, it should allow a margin of 8 or 12μs. Remark that when the MLX90109 picks up a Manchester-encoded signal whereas the MODE pin is strapped to V SS (= Biphase decoding), the clock will also be asymmetric. 9.6. Close coupling For very short operating distances, a strong coupling with a tag may drastically reduce the antenna impedance Z ant. If the current (Idriver) driven by the antenna internal driver FET goes higher than 14mA, the antenna voltage Vant may be reduced and the MLX90109 may be unable to read the transponder. Coupling effect is application-dependent and must be evaluated case by case. Page 12 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 10. Typical configuration: READ/WRITE ON/OFF keying (FDX-B100) 10.1. Application diagram The basic principle is to switch the voltage on MODU between 0V and V DD. The antenna will reach its maximum amplitude in less than 3 periods when MODU is stepped down from V DD to VSS. Setting the chip in power-down (set VMODU up to VDD) will let the antenna fade-out with a time constant, depending on the antenna’s quality factor Q ant. For fast protocols, an additional drain resistor on MODU controlled by the microcontroller could be used to decrease the fall time (refer to the application note MLX90109 “100% modulation (ON/OFF Keying)”. FAST_MOD VDD Microcontroller VDD CD=100nF 7 3 4 6 5 100k 8 2 100k 1 MLX 90109 C1 100k L, C DATA CLOCK MODE 19k SPEED MODU Note : Care should be taken to the capacitor C1 which may reduce the fall time. Page 13 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 11. Standard information regarding manufacturability of Melexis products with different soldering processes Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity level according to following test methods: Reflow Soldering SMD’s (Surface Mount Devices)   IPC/JEDEC J-STD-020 Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices (classification reflow profiles according to table 5-2) EIA/JEDEC JESD22-A113 Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing (reflow profiles according to table 2) Wave Soldering SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)   EN60749-20 Resistance of plastic- encapsulated SMD’s to combined effect of moisture and soldering heat EIA/JEDEC JESD22-B106 and EN60749-15 Resistance to soldering temperature for through-hole mounted devices Iron Soldering THD’s (Through Hole Devices)  EN60749-15 Resistance to soldering temperature for through-hole mounted devices Solderability SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)  EIA/JEDEC JESD22-B102 and EN60749-21 Solderability For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature, temperature gradient, temperature profile etc) additional classification and qualification tests have to be agreed upon with Melexis. The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance of adhesive strength between device and board. Melexis is contributing to global environmental conservation by promoting lead free solutions. For more information on qualifications of RoHS compliant products (RoHS = European directive on the Restriction Of the use of certain Hazardous Substances) please visit the quality page on our website: http://www.melexis.com/quality.aspx 12. ESD Precautions Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. Page 14 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 13. FAQ 13.1. Is it possible to make proportional modulation (depth less than 100%) with the MLX90109? The amplitude of the MLX90109 antenna can be adjusted on the fly by changing the MODU pin level between V MODU = 0.8V and Vpd. However, the MLX90109 cannot change instantaneously the voltage on its antenna according to a voltage step on MODU pin, and a transient waveform will appear on the voltage antenna. This particular waveform may disturb the transponder and in the worst case (modulation depth more than 20%) the MLX90109 may stop its oscillation. Using the MLX90109 with proportional modulation (modulation depth less than 100%) is not recommended and supported by Melexis and must be evaluated case by case. 13.2. How should I read data information from a transponder up to 15cm? The reading distance depends on the complete system composed by the reader and the transponder. A reading distance with the MLX90109 transceiver up to 15cm has been demonstrated with a specific reader’s antenna (diameter = 130mm, Inductance = 44μH, Quality factor Qant = 87.2@125kHz) and a transponder with a credit card size antenna (80 x 50mm). 13.3. Is it possible to increase the output power of the MLX90109 transceiver? The current flowing through the antenna (IANT) can be maximized by a careful design, respecting the design specification of the MLX90109 (Auto start-up impedance, the maximum driver current IDRIVER). The voltage on the antenna cannot be increased as it is limited by the power supply V DD (Vant ≤ VDD-VMODU+Vos). Moreover, as the MLX90109 uses the same connection (COIL ) for the transmission and the reception, it is not possible to use an external power transistor supplied with a higher voltage than VDD. 13.4. Are there any specific coils available for the MLX90109 transceiver? Melexis has developed an 18mm coil which is used on the evaluation board EVB90109. Please contact your sales channel if you wish to purchase production quantities. 13.5. What are the recommended pull-up values on DATA and CLOCK pins? The DATA and CLOCK are open-drain drivers which require external pull-up resistors. The values are not critical therefore, to reduce the general power consumption, we recommend to use high ohmic (100k ohm) pull up resistances. Page 15 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 14. Package Information 14.1. Plastic SO8 The device is packaged in a 8 pin lead free SO package (ROHS compliant MSL1/260°C). E1 E 1 2 3 D  A1 A e L b all Dimension in mm, coplanarity < 0.1mm D E1 E A A1 e b L a min 4.80 3.81 5.80 1.32 0.10 1.27 0.36 0.41 0° max 4.98 3.99 6.20 1.72 0.25 0.46 1.27 8° all Dimension in inch, coplanarity < 0.004” min 0.189 0.150 0.2284 0.060 0.0040 0.05 0.014 0.016 0° max 0.196 0.157 0.2440 0.068 0.0098 0.050 8° 0.018 Page 16 of 17 REVISION 011 - JUNE 19, 2017 3901090109 MLX90109 125kHz RFID Transceiver 15. Contact For the latest version of this document, go to our website at www.melexis.com. For additional information, please contact our Direct Sales team and get help for your specific needs: Europe, Africa Telephone: +32 13 67 04 95 Email : sales_europe@melexis.com Americas Telephone: +1 603 223 2362 Email : sales_usa@melexis.com Asia Email : sales_asia@melexis.com 16. Disclaimer The information furnished by Melexis herein (“Information”) is believed to be correct and accurate. Melexis disclaims (i) any and all liability in connection with or arising out of the furnishing, performance or use of the technical data or use of the product(s) as described herein (“Product”) (ii) any and all liability, including without limitation, special, consequential or incidental damages, and (iii) any and all warranties, express, statutory, implied, or by description, includ ing warranties of fitness for particular purpose, noninfringement and merchantability. No obligation or liability shall arise or flow out of Melexis’ rendering of technical or other services. The Information is provided "as is” and Melexis reserves the right to change the Information at any time and without notice. Therefore, before placing orders and/or prior to designing the Product into a system, users or any third party should obtain the latest version of the relevant information to verify that the information being relied upon is current. Users or any third party must further determine the suitability of the Product for its application, including the level of reliability required and determine whether it is fit for a particular purpose. The Information is proprietary and/or confidential information of Melexis and the use thereof or anything described by the Information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights. This document as well as the Product(s) may be subject to export control regulations. Please be aware that export might require a prior authorization from competent authorities. The Product(s) are intended for use in normal commercial applications. Unless otherwise agreed upon in writing, the Product(s) are not designed, authorized or warranted to be suitable in applications requiring extended temperature range and/or unusual environmental requirements. High reliability applications, such as medical life-support or lifesustaining equipment are specifically not recommended by Melexis. The Product(s) may not be used for the following applications subject to export control regulations: the development, product ion, processing, operation, maintenance, storage, recognition or proliferation of 1) chemical, biological or nuclear weapons, or for the development, production, maintenance or storage of missiles for such weapons: 2) civil firearms, including spare parts or ammunition for such arms; 3) defense related products, or other material for military use or for law enforcement; 4) any applications that, alone or in combination with other goods, substances or organisms could cause serious harm to persons or goods and that can be used as a means of violence in an armed conflict or any similar violent situation. The Products sold by Melexis are subject to the terms and conditions as specified in the Terms of Sale, which can be found at https://www.melexis.com/en/legal/terms-andconditions. This document supersedes and replaces all prior information regarding the Product(s) and/or previous versions of this document. Melexis NV © - No part of this document may be reproduced without the prior written consent of Melexis. (2016) ISO/TS 16949 and ISO14001 Certified Page 17 of 17 REVISION 011 - JUNE 19, 2017 3901090109