US91AEZE-AAA-000-RE

US90A/US91A Datasheet 1. Features and Benefits 3. Description  Integrated High sensitivity Hall Sensor  No VDD concept The US90A/91A is a one-chip solution for driving two-coil brushless DC cooling fans.  Locked rotor protection and auto-restart  Power-efficient CMOS and power MOSFETs  Built-in output protection clamping diode  Integrated tachometer (FG: US90A) or alarm (RD: US91A) signal output  FG/RD SIP package options:   Based on the advanced Melexis CMOS process, the IC contains a Hall-effect sensor, dynamic offset correction and low side output drivers. Frequency Generator or Rotation Detection is available. The open-drain output makes the connectivity with any external interface such as hardware monitoring or Super I/O IC easier. 4 pins VA and VK package SMD package options  SOIC8 bent leads  SOT25 straight leads  RoHS Compliant  Peak current up to 500mA These features are combined with the Melexis patented no-VDD design to fit the IC in small 4-pin VK and VA package. The device is also delivered in DC package for automatic assembly. 2. Application Examples  12V and 24V 2-coil fans Figure 1 REVISION 06 – 20 JUL 2017 US90A/US91A Datasheet Contents 1. Features and Benefits ............................................................................................................................ 1 2. Application Examples............................................................................................................................. 1 3. Description ............................................................................................................................................ 1 4. Ordering Information ............................................................................................................................ 3 5. Glossary of Terms .................................................................................................................................. 4 6. Pin Definitions and Descriptions ............................................................................................................ 4 7. Electrical Specifications ......................................................................................................................... 5 7.1. Absolute Maximum Ratings ............................................................................................................... 5 7.2. General Electrical Specifications ........................................................................................................ 5 7.3. Magnetic Specifications ...................................................................................................................... 6 7.4. Driver output vs Magnetic pole ......................................................................................................... 6 8. Description ............................................................................................................................................ 7 8.1. General description ............................................................................................................................ 7 8.2. No-VDD concept ................................................................................................................................. 7 8.3. LRP ....................................................................................................................................................... 7 9. Performance Graphs.............................................................................................................................. 8 10. Application Information....................................................................................................................... 9 11. Package Information.......................................................................................................................... 10 11.1. VK Package Information (4-pin TO92) ........................................................................................... 10 11.2. Trimmed VK T&R(dead bug) : VKAAA000-RX ............................................................................... 10 11.2.1. VKAA000-RX Tape ..................................................................................................................... 11 11.2.2. VKAAA000-RX Lead Trim length............................................................................................... 11 11.3. DC Package Information (8-pin narrow SOIC) ............................................................................... 11 11.4. VA Package Information (4-pin TO92 flat)..................................................................................... 12 11.5. ZE Package (SOT25 with straight leads)......................................................................................... 14 12. Standard Information ........................................................................................................................ 14 13. ESD Precautions................................................................................................................................. 15 14. Disclaimer .......................................................................................................................................... 15 15. Revision History Table ....................................................................................................................... 16 16. Contact .............................................................................................................................................. 16 REVISION 006 – 20 JUL 2017 Page 2 of 16 US90A/US91A Datasheet 4. Ordering Information Product Temperature Package Option Code Packing Form Description US90A E DC AAA-000 RX FG (frequency output) US91A E DC AAA-000 RX RD (alarm output) US90A E VK AAA-000 BU FG (frequency output) US90A E VK AAA-000 RX VK cut leads in T&R FG (frequency output) US91A E VK AAA-000 BU RD (alarm output) US91A E VK AAA-000 RX VK cut leads in T&R RD (alarm output) US90A E VA AAA-000 BU FG (frequency output) US91A E VA AAA-000 BU RD (alarm output) US90A E ZE AAA-000 RE FG (frequency output) US91A E ZE AAA-000 RE RD (alarm output) Legend: Package Code: “DC” for SOIC-8 package “VK” for Plastic Single in Line thickness 1.5 - 1.6mm “VA” for Plastic Single in Line thickness 1.1 -1.2mm “ZE” for straight leads SOT25 Packing Form: “RE for Reel, live bug (die face up)” “RX for Reel, dead bug (die face down)” “BU for Bulk bag” Ordering Example: “US91AEZE AAA000-RE” For an RD output in straight leads SOT25 package, delivered in Reel. Table 1 REVISION 006 – 20 JUL 2017 Page 3 of 16 US90A/US91A Datasheet 5. Glossary of Terms Gauss (G), Tesla (T) Units for the magnetic flux density  1 mT = 10 G NC Not Connected Two-coil fan A fan with two-coil windings where current alternates from 1 coil to the other depending on the direction of the magnetic field. MilliTesla (mT), Gauss Units of magnetic flux density: 1mT = 10 Gauss VDD Voltage on the coils common node. IDD Current supplying the chip which flows through the coil connected to the switched off output driver. Peak output current The current flowing in the coil at start-up, only limited by the coil resistance RCOIL and the output driver resistance RDSON. Continuous output current The current flowing in the coil when the fan is spinning normally Locked rotor The state when the fan stopped spinning due to mechanical blockage. FG Frequency generator or tachometer output RD Rotation detection or alarm output LFPM Linear Feet Per Minute – Unit of airflow velocity Table 2 6. Pin Definitions and Descriptions Name SOIC8 SOT25 VK VA Description Pin # Pin # Pin # Pin # FG (RD) 1 4 1 1 open drain output signal OUT1 2 3 2 2 Open Drain Coil Driver 1 OUT2 3 1 3 4 Open Drain Coil Driver 2 GND 4 2 4 3 Ground pin N.C. 5,6,7,8 5 Not Connected Table 3 REVISION 006 – 20 JUL 2017 Page 4 of 16 US90A/US91A Datasheet For optimal EMC behavior connect the unused pins (Not Used) to the Ground. 7. Electrical Specifications 7.1. Absolute Maximum Ratings Parameter Symbol Value Units Fan Supply Voltage VDD 30 V Maximum voltage OUT1, OUT2 Vout 100 V Peak Output Current IOUTp 500 mA Continuous Output Current IOUTc 250 mA FG / RD Output Current IFG (RD) 20 mA Junction Temperature TJ -40 to 125 °C Storage Temperature Range TS -55 to 150 °C Magnetic Flux Density B Unlimited mT ESD HBM ESDhbm 4000 V Table 4 Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute maximumrated conditions for extended periods may affect device reliability. 7.2. General Electrical Specifications o DC Operating Parameters TA = 25 C, VDD = 24V (unless otherwise specified) Parameter Symbol Test Conditions Min Fan Supply Voltage VDD Operating, RCOIL = 50Ω 4.7(1) Supply Current IDD Output Saturation Voltage VDSON IOUT = 150mA 375 mV Output Saturation Voltage VDSON IOUT = 250mA 625 mV Output Clamp Voltage VOUT FG / RD Output Low Voltage VOL FG / RD Output Clamp Voltage VCLAMP REVISION 006 – 20 JUL 2017 Typ 2 60 IOL = 10mA 250 28 Max Units 30 V 4 mA 80 V 500 mV V Page 5 of 16 US90A/US91A Datasheet Parameter Symbol Test Conditions Min Typ FG / RD Output Leakage Current ILEAK VFG (VRD) = 18V Locked rotor ON time Ton Locke rotor OFF time Toff DC Thermal Resistance RTHja (2) 150 °C/Watt VK Thermal Resistance RTHja (2) 200 °C/Watt VA Thermal Resistance RTHja (2) 170 °C/Watt ZE Thermal Resistance RTHja (2) 170 °C/Watt ZE Thermal Resistance RTHjc 20 °C/Watt 210 Auto restart after locked rotor shut down Max Units 10 uA 350 ms 6.3*Ton Junction to package top Table 5 Note 1: The minimal value of VDD should be determined using the following equation: VDD = 4.5V + RCOIL * IDD Note 2: Rthja for JEDEC single layer board 76.2 x 114.3 x 1.60, zero LFPM 7.3. Magnetic Specifications o DC Operating Parameters TA = 25 C, VDD = 24V (unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Units Operate point BOP 3 6 mT Release point BRP 6 3 mT Hysteresis BHYST 2 6 mT Table 6 magnetic specification 7.4. Driver output vs Magnetic pole Parameter Test Conditions OUT1 OUT2 North pole B < Brp – all packages High Low South pole B > Bop all packages Low High Table 7: Driver output vs. mangetic pole Note: The magnetic pole is applied facing the branded side of the package REVISION 006 – 20 JUL 2017 Page 6 of 16 US90A/US91A Datasheet 8. Description 8.1. General description The US90A/91A is a one-chip solution for driving two-coil brushless DC fans. Based on advanced Melexis CMOS process, the IC contains a Hall-effect sensor, dynamic offset correction and low side output drivers. The output drivers OUT1 and OUT2 are fully protected against switching transients. So there is no need for an external zener diode to cut the high voltage spikes induced by the fan coils. The US90A has an open-drain integrated tachometer FG output that follows the Hall signal. In the US91A, the open-drain rotation detection output RD is active low during normal spinning of the motor. It goes high when the flux switching frequency becomes too low, which means the motor is blocked. 8.2. No-VDD concept The absence of a VDD pin enables the two low side output drivers and FG/RD signal output to fit in a four-pin VK package. The lack of a VDD pin decreases also the probability to damage the chip due to reverse voltage connection, using the coil resistance to limit the reverse current. In this condition, the total reverse current is twice the peak current value of the fan used. 8.3. LRP The built-in locked-rotor protection will automatically shut off the coil current when the rotor is mechanically blocked, or the rotational speed drops below 60 RPM (4-pole rotor magnet). The fan will try to restart every 1.5 seconds until the obstruction is clear. The On / Off cycling reduces the average stall current to 1/7 normal; this is enough to prevent overheating or damage to most fans. Both the US90A and US91A have this feature. REVISION 006 – 20 JUL 2017 Page 7 of 16 US90A/US91A Datasheet 9. Performance Graphs 11.1 RDSON vs TJ 11.2 RDSON vs VDD 11.3 Magnetic parameters vs TJ 11.4 Magnetic parameters vs VDD 11.5 IDD vs TJ 11.6 IDD vs VDD 11.7 VOL vs TJ 11.8 Power Dissipation vs. TA REVISION 006 – 20 JUL 2017 Page 8 of 16 US90A/US91A Datasheet 10. Application Information Typical application with pull-up resistor Configuration for reverse voltage protection The left schematic shows an application including several external protections. The diode DREVPROT best protects the chip and fan coils for reverse voltage condition. The no-VDD design enables ESD protection at fan module level to be easily improved. The fan coils prevent and filter fast current stress on OUT1 and OUT2, resulting in better ESD protection. REVISION 006 – 20 JUL 2017 Page 9 of 16 US90A/US91A Datasheet 11. Package Information 11.1. VK Package Information (4-pin TO92) 11.2. Trimmed VK T&R(dead bug) : VKAAA000-RX REVISION 006 – 20 JUL 2017 Page 10 of 16 US90A/US91A Datasheet 11.2.1. VKAA000-RX Tape Die is face down. Top Marking is face down in the tape: 11.2.2. VKAAA000-RX Lead Trim length 11.3. DC Package Information (8-pin narrow SOIC) REVISION 006 – 20 JUL 2017 Page 11 of 16 US90A/US91A Datasheet 11.4. VA Package Information (4-pin TO92 flat) REVISION 006 – 20 JUL 2017 Page 12 of 16 US90A/US91A Datasheet REVISION 006 – 20 JUL 2017 Page 13 of 16 US90A/US91A Datasheet 11.5. ZE Package (SOT25 with straight leads) 0.04 0.07 0.27 NC FG NC RD 5 4 5 4 |90YY |WW X X X 1 OUT2 2 3 GND OUT1 |91YY |WW X X X 1 2 3 OUT2 GND OUT1 Top marking US91A, US90A 12. Standard Information REVISION 006 – 20 JUL 2017 Page 14 of 16 US90A/US91A Datasheet Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity level according to standards in place in Semiconductor industry. For further details about test method references and for compliance verification of selected soldering method for product integration, Melexis recommends reviewing on our web site the General Guidelines soldering recommendation. For all soldering technologies deviating from the one mentioned in above document (regarding peak temperature, temperature gradient, temperature profile etc), additional classification and qualification tests have to be agreed upon with Melexis. For package technology embedding trim and form post-delivery capability, Melexis recommends to consult the dedicated trim&form recommendation application note: lead trimming and forming recommendations Melexis is contributing to global environmental conservation by promoting lead free solutions. For more information on qualifications of RoHS compliant products (RoHS = European directive on the Restriction Of the use of certain Hazardous Substances) please visit the quality page on our website: http://www.melexis.com/en/quality-environment 13. ESD Precautions Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. 14. Disclaimer The information furnished by Melexis herein is believed to be correct and accurate. Melexis disclaims (i) any and all liability in connection with or arising out of the furnishing, performance or use of the technical data or use of the product as described herein, (ii) any and all liability, including without limitation, special, consequential or incidental damages, and (iii) any and all warranties, express, statutory, implied, or by description, including warranties of fitness for particular purpose, non-infringement and merchantability. No obligation or liability shall arise or flow out of Melexis’ rendering of technical or other services. The information contained herein is provided "as is” and Melexis reserves the right to change specifications and/or any other information contained herein at any time and without notice. Therefore, before placing orders and/or prior to designing this product into a system, users or any third party should obtain the latest version of the relevant information to verify that the information being relied upon is current. This document supersedes and replaces all prior information regarding the product(s) as described herein and/or previous versions of this document. Users or any third party must further determine the suitability of the Melexis’ product(s) described herein for its application, including the level of reliability required and determine whether it is fit for a particular purpose. The information contained herein is proprietary and/or confidential information of Melexis. The information contained herein or any use thereof does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. This document as well as the product(s) described herein may be subject to export control regulations. Please be aware that export might require a prior authorization from competent authorities. The product(s) as described herein is/are intended for use in normal commercial applications. Unless otherwise agreed upon in writing, the product(s) described herein are not designed, authorized or warranted to be suitable in applications requiring extended temperature range, unusual environmental requirements. High reliability applications, such as medical life-support or life-sustaining equipment are specifically not recommended by Melexis. REVISION 006 – 20 JUL 2017 Page 15 of 16 US90A/US91A Datasheet The product(s) may not be used for the following applications subject to export control regulations: the development, production, processing, operation, maintenance, storage, recognition or proliferation of 1) chemical, biological or nuclear weapons, or for the development, production, maintenance or storage of missiles for such weapons: 2) civil firearms, including spare parts or ammunition for such arms; 3) defense related products, or other material for military use or for law enforcement; 4) any applications that, alone or in combination with other goods, substances or organisms could cause serious harm to persons or goods and that can be used as a means of violence in an armed conflict or any similar violent situation. Products sold by Melexis are subject to the terms and conditions as specified in the Terms of Sale, which can be found at https://www.melexis.com/en/legal/terms-and-conditions. Melexis NV © - No part of this document may be reproduced without the prior written consent of Melexis. (2016) ISO/TS 16949 and ISO14001 Certified 15. Revision History Table Added US91AEVK-AAA000-RX options Added Ton/Toff specification. 006 Added SOT straight leads package: 11.5ZE Package (SOT25 with straight leads) Added marking info VA, VK Added ESD hbm rating Corrected characterization graphs for RDSon Table 8 16. Contact For the latest version of this document, go to our website at www.melexis.com. For additional information, please contact our Direct Sales team and get help for your specific needs: Europe, Africa Telephone: +32 13 67 04 95 Email : sales_europe@melexis.com Americas Telephone: +1 603 223 2362 Email : sales_usa@melexis.com Asia Email : sales_asia@melexis.com REVISION 006 – 20 JUL 2017 Page 16 of 16