ES3G

SURFACE MOUNT SUPER FAST RECTIFIER ES3A THRU ES3J FEATURES • • • • • VOLTAGE RANGE CURRENT 50 to 600 Volts 3.0 Ampere Plastic package has underwrites laboratory Flammability Classification 94V-0 Glass passivated chip junction Built-in strain relief, Suoer Fast switching speed for high efficiency High temperature soldering guaranteed: 260℃/10 seconds DO-214AB(SMC) MECHANICAL DATA • • • • Case: JEDED DO-214AB transfer molded plastic Terminals: Solder plated, solderable per MIL-STD-750 Method 2026 Polarity: Color band denotes cathode end Weight: 0.007 ounce, 0.25 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20%. SYMBOLS ES3A ES3B Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 • • • Maximum Average Forward Rectified Current at TL=100℃ Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage @ 3.0A Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage per element TA = 125℃ Typical Reverse Recovery Time Test conditions IF =0.5A, IR =1.0A, IRR =0.25A Typical Junction Capacitance ( Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance (Note 1) Operating Junction Temperature Range Storage Temperature Range ES3C 150 105 150 ES3D 200 140 200 3.0 100 ES3E 300 210 300 ES3G 400 280 400 ES3J 600 420 600 UNIT Volts Volts Volts Amps Amps I(AV) IFSM VF IR trr CJ RθJA RθJL TJ TSTG 45 0.95 1.25 5.0 300 35 1.7 Volts µA nS 30 55 17 (-55 to +150) (-55 to +150) pF ℃/W ℃ ℃ Notes: 1. Thermal resistance from Junction to ambient and from junction to lead mounted on P.C.B. with 0.3”×0.3”(8.0mm × 8.0mm) copper pad areas. E-mail: sales@cnmic.com Web Site: www.cnmic.com SURFACE MOUNT SUPER FAST RECTIFIER ES3A THRU ES3J VOLTAGE RANGE CURRENT 50 to 600 Volts 3.0 Ampere RATING AND CHRACTERISTIC CURVES ES3A THRU ES3J FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE AV ERAGE FO RWA RD CURRE NT, 3.0 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEA K FORWARD S URG E 150 8.3ms Single Half Sine-Wave 2.0 CURRE NT, ( A) (JEDEC Method) Tj = Tjmax ( A) 100 Single Phase Half Wave 1.0 60Hz Inductive or Resistive Load 0.375″(9.5mm) Lead Length 50 0 0 25 50 75 100 125 150 175 0 1 1 Cycle 2 4 6 8 10 20 40 60 100 AMBIENT TEMPERATURE, (° C) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEO US REV ERSE CURRENT, 10 INSTANTANE OUS FORWARD CURRENT, 3D ES 3E ES 3J 1.0 ES 3A- -3 G 1.0 0.1 TJ =25° C Pulse Width=300us 1% Duty Cycle (μA) (A ) TJ =125° C 0.1 0.01 TJ =25℃ 0.01 0 0.001 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.5-TYPICAL JUNCTION CAPACITANCE 1000 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) JUNCTION CA PACITANCE,( pF) F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC TRR 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE (-) 100 (+) 25 Vdc (approx.) (-) TJ =25° C f=1MHz Vsig=50mVp-p ES3A-ES3D ES3E-ES3J 10 0.1 1.0 10 100 D.U.T. PULSE GENERATIOR (NOTE 2) (+) OSCILLOSCOPE (NOTE 1) +0.5A 0 -0.25A 1Ω NON INDUCTIVE -1.0A 1cm REVERSE VOLTAGE,(V) NOTES : 1.Rise Time=7ns max. Input Impedance= 1 megohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms SET TIME BASE FOR 50/100ns/cm E-mail: sales@cnmic.com Web Site: www.cnmic.com