ESM1J

SURFACE MOUNT SUPER FAST RECTIFIER ESM1A THRU ESM1J FEATURES • • • • • • VOLTAGE RANGE FORWARD CURRENT 50 to 600Volts 1.0 Ampere For surface mounted applications Glass passivated chip junction Low leakage current Fast switchig Plastic package has underwrites laboratory flammability Classification 94V-0 High temperature soldering guaranteed 250℃/10 seconds at terminals DO-213AB MECHANICAL DATA • • • • Case: molded plastic Polarity: band indicate cathode Mounting position: Any Weight: 0.12 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS ESM 1A 50 35 50 ESM 1B 100 70 100 ESM 1C 150 105 150 ESM 1D 200 140 200 1.0 30 095 1.25 5.0 100 35 15 40 -55 to +150 1.7 ESM 1E 300 210 300 ESM 1G 400 280 400 ESM 1J 600 420 600 UNITS Volts Volts Volts Amps Amps Volts µA ns PF ℃/W ℃ Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage M aximum Average Forward Rectified Current at T T=100 ℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current at rated DC Blocking Voltage at T A = 25℃ TA = 125℃ VRRM VRMS VDC I(AV) IFSM VF IR Trr CJ RθJT TJ,TSTG Typical Reverse Recovery Time (NOTE 1) Typical Junction Capacitance (Note 2) Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range Notes: 1. Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts. 3. Thermal resistance Junction to terminal 6.0mm2 copper pads to each terminal. E-mail: sales@cnmic.com Web Site: www.cnmic.com SURFACE MOUNT SUPER FAST RECTIFIER ESM1A THRU ESM1J VOLTAGE RANGE FOEWARD CURRENT 50 to 600Volts 1.0 Ampere RATINGS AND CHARACTERISTIC CURVES ESM1A THRU ESM1J FIG.1-MAXMUM FORWARD CURRENT DERATING CURVE 1.2 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT,(A) 30 8.3ms Single Half Sine-Wave AVERAGE FORWARD CURRENT(A) 1.0 0.8 0.6 0.4 Resistive or Inductive Load 25 20 15 10 (JEDEC Method)T =110 ° c T 0.2 0 80 P.C.B Mounted 0.2x0.2"(5.0x5.0mm) Copper Pad Areas 5.0 0 1 10 100 90 100 110 120 130 140 150 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS I NSTANTANEOUS FORWARD CURRENT,( A) 5.0 FIG.4-TYPICAL REVERSE LEAKAGE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT,( uA) 1000 T J=125 ° C 1.0 A-1 M 1E D 1J -1 G 100 M1 0.1 ES T J=25 ° C Pulse Width=300us 1% Duty Cycle ES M 10 ES T J=75 ° C 1.0 T =25 ° C J 0.01 0.1 0.001 0.4 0.6 0.8 1.0 1.2 1.4 0.01 0 20 40 60 80 100 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) TRANSIENT THERMAL I MPEDANCE( ℃/W) FIG.5-TYPICAL JUNCTION CAPACITANCE 60 T =25 ° C J Pulse Width=300us 1% Duty Cycle FIG.6-TRANSIENT THERMAL IMPEDANCE 100 Mounted on 0.20x0.27"(5.0x7.0mm) Copper Land Areas JUNCTION CAPACITANCE,(pF) 50 40 30 20 10 0 0.1 1.0 10 1 0.1 1.0 10 100 10 100 T,PULSE DURATION(SEC.) REVRESE VOLTAGE,(V) E-mail: sales@cnmic.com Web Site: www.cnmic.com