FR602G

FAST RECOVERY GLASS PASSIVATED RECTIFIER FR601G THRU FR607G FEATURES • • • • • VOLTAGE RANGE CURRENT 50 to 1000 Volts 6.0 Ampere R-6 Fast switching for high efficiency Glass passivated chip junction High current surge capability Low leakage High temperature soldering guaranteed 260℃/10 seconds,0.375”(9.5mm)lead length at 5 lbs (2.3kg) tension MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.07 ounce, 2.0 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% FR FR SYMBOLS 601G 602G Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 • • • Maximum Average Forward Rectified Current 0.375″(9.5mm) lead length at T A =55℃ Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 3.0A Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage TA = 125℃ Maximum Reverse Recovery Time(NOTE 3) Typical Junction Capacitance (NOTE 1) Typical Thermal Resistance (NOTE 2) Operating Temperature Range Storage Temperature Range FR 603G 200 140 200 FR 604G 400 280 400 6.0 250 1.3 10 500 FR 605G 600 420 600 FR 606G 800 560 800 FR 607G 1000 700 1000 UNIT Volts Volts Volts Amps Amps Volts µA I(AV) IFSM VF IR trr CJ RθJA TJ TSTG 150 250 90 10 (-55 to +150) (-55 to +150) 500 nS pF ℃/W ℃ ℃ Notes: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2. Thermal Resistance from Junction to Ambient at.375″(9.5mm) lead length, P.C board mounted. 3. Test conditions: IF=0.5A, IR=1.0A, IRR=0.25A. E-mail: sales@cnmic.com Web Site: www.cnmic.com FAST RECOVERY GLASS PASSIVATED RECTIFIER FR601G THRU FR607G VOLTAGE RANGE CURRENT 50 to 1000 Volts 6.0 Ampere RATING AND CHRACTERISTIC CURVES FR601G THRU FR607G FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, 6.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE 300 CURRENT, (A) 8.3ms Single Half Sine-Wave (JEDEC Method) T= T jmax 200 4.0 (A) 2.0 100 0 0 25 50 55 75 100 125 150 175 0 1 1 Cycle 60 80 100 2 4 6 8 10 20 40 AMBIENT TEMPERATURE, ( ° C) NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, INSTANTANEOUS REVERSE CURRENT, 10 FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 TJ =125 ° C 10 1.0 (A) (μA) TJ =100 ° C 1.0 0.1 TJ =75° C TJ =25° C Pulse Width=300us 1% Duty Cycle 0.01 0.4 0.1 TJ=25 ° C 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE,(V) 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK FIG.5-TYPICAL JUNCTION CAPACITANCE 210 REVERSE VOLTAGE,(%) JUNCTION CAPACITANCE,(pF) 180 F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 150 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE (-) (+) D.U.T. PULSE GENERATIOR (NOTE 2) (+) OSCILLOSCOPE (NOTE 1) +0.5A 120 0 -0.25A 90 25 Vdc (approx.) (-) T J =25 ° C f=1MHz Vsig=50mVp-p 60 1Ω NON INDUCTIVE -1.0A 1cm 30 0 0.1 1.0 10 100 200 REVERSE VOLTAGE,(V) NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms SET TIME BASE FOR 50/100ns/cm E-mail: sales@cnmic.com Web Site: www.cnmic.com