FR804

FAST RECOVERY RECTIFIER FR801 THRU FR806 FEATURES • • • • • • • • VOLTAGE RANGE CURRENT 50 to 1000 Volts 8.0 Ampere Glass passivated chip junction Low cost construction Fast switching for high efficiency Low reverse leakage High forward surge current capacity High temperature soldering guaranteed 260℃/10 second,0.375″(9.5mm)lead length at 5 lbs (2.3kg) tension TO-220AC MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Polarity: Color band denotes cathode end Lead: Plated axial lead, solderable per MIL-STD-202E method 208C Mounting position: Any Weight: 0.064ounce, 1.81 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS FR801 FR802 Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 • • • Maximum Average Forward Rectified Current 0.375″(9.5mm) lead length at Tc=100℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 8.0A Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage per element TA = 100℃ Maximum Reverse Recovery Time (NOTE 3)Tj=25℃ Typical Junction Capacitance (NOTE 1) Typical Thermal Resistance (NOTE 2) Operating and Storage Temperature Range Storage Temperature Range FR803 200 140 200 8.0 200 1.3 10 500 FR804 400 280 400 FR805 600 420 600 FR806 800 560 800 UNIT Volts Volts Volts Amps Amps Volts µA I(AV) IFSM VF IR trr CJ RθJC TJ TSTG 150 250 50 3.0 (-55 to +150) (-55 to +150) 500 nS pF ℃/W ℃ ℃ Notes: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2. Thermal Resistance from Junction to CASE 3. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A E-mail: sales@cnmic.com Web Site: www.cnmic.com FAST RECOVERY RECTIFIER FR801 THRU FR806 VOLTAGE RANGE CURRENT 50 to 1000 Volts 8.0 Ampere RATING AND CHRACTERISTIC CURVES FR801G THRU FR806 FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FOR WARD CU RRENT, 12.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375 ″(9.5mm) Lead Length FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE 300 CURR ENT, (A) 8.3ms Single Half Sine-Wave (JEDEC Method) T= T jmax 200 8.0 ( A) 4.0 100 1 Cycle 0 0 25 50 75 100 125 150 175 0 1 2 4 6 8 10 20 40 60 80 100 AMBIENT TEMPERATURE, (° C) NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, 20 FIG.4-TYPICAL REVERSE CHARACTERISTICS 10 TJ =100 ° C IN STANTANEOUS FORWARD CURR ENT, 10 1 (A) (μA) 1.0 TJ =25 ° C 0.1 0.1 TJ =25 ° C Pulse Width=300us 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.01 0 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE 1000 JUNC TION C APAC ITANCE,(pF) F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50 Ω 10Ω NONINDUCTIVE NONINDUCTIVE (-) 100 (+) 25 Vdc (approx.) (-) T J =25 ° C f=1MHz Vsig=50mVp-p D.U.T. PULSE GENERATIOR (NOTE 2) (+) OSCILLOSCOPE (NOTE 1) +0.5A 0 -0.25A 1Ω NON INDUCTIVE -1.0A 1cm 10 0.1 1.0 10 100 REVERSE VOLTAGE,(V) NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms SET TIME BASE FOR 50/100ns/cm E-mail: sales@cnmic.com Web Site: www.cnmic.com