GBJ1001

SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER GBJ10005 THRU GBJ1010 FEATURES • • • • • • VOLTAGE RANGE CURRENT 50 to 1000 Volts 10.0 Amperes O 19.7-20.3 • • • • • Case: molded plastic body Terminal: Plated leads solderable per MIL-STD-750 Method 2026 Mounting position: Any (Note 3) Mounting Torque: 6 in – 1bs max. Weight: 0.15 ounce,4.0 gram 3.8-4.2 17.0-18.0 MECHANICAL DATA 2.5±0.2 2.0-2.4 2.7-3.1 0.9-1.1 9.8-10.2 7.3-7.7 7.3-7.7 0.6-0.8 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% GBJ SYMBOLS GBJ 10005 GBJ 1002 GBJ 1004 GBJ 1006 GBJ 1008 GBJ 1010 1001 Maximum Reverse Peak Repetitive Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward At T C=100℃(Note Rectified Current, At TA=40℃(Note Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per bridge element 5.0A Maximum DC Reverse Current at rated DC blocking voltage per element TA=25℃ TA=125℃ VRRM VRMS VDC 1) 2) I(AV) IFSM I2 t VF IR CJ RJC TJ TSTG 50 35 50 100 70 100 200 140 200 400 280 400 10 5.0 170 142 1.0 5.0 250 60 2.2 (-55 to +150) (-55 to +150) 600 420 600 800 560 800 1000 700 100 10.8-11.2 5.0 Plastic package has UL Flammability Glassification 94V-0 Glass passivated chip junctions High case dielectric strength of 1500 VRMS High surge current capability Ideal for printed circuit boards High temperature soldering guaranteed 260℃/10 seconds, 0.375”(9.5mm) lead length GBJ 29.7-30.3 3.0×45 O 4.4-4.8 3.4-3.8 .1 3 .4 φ3 UNIT Volts Volts Volts Amps Amps A2s Volts μA Typical Junction Capacitance, per let (Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance (Note 2 and 3) Operating Junction Temperature Range Storage Temperature Range pF ℃/W ℃ ℃ Notes: 1. Unit mounted on 150mm×150mm×1.6mm A1. Plate heatsink 2. Unit mounted on P.C.B. With 0.5×0.5”(1.2×1.2mm) copper pads and 0.375”(9.5mm) lead length 3. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum Heat transfer with #6 screw E-mail: sales@cnmic.com Web Site: www.cnmic.com SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER GBJ10005 THRU GBJ1010 VOLTAGE RANGE CURRENT 50 to 1000 Volts 10.0 Amperes RATINGS AND CHARACTERISTIC CURVES GBJ10005 THRU GBJ1010 FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT 15 FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG AVERAGE FORWARD OUTPUT CURRENT (A) Heat-Sink Mounting. Tc 10 PEAK FORWA RD SURGE, CURRENT,(A) 200 5 P.C.B. Mounting 100 1.0 Cycle 0 0 25 50 75 100 125 150 175 0 1 2 4 6 8 10 20 40 60 100 TEMPERATURE, ℃ FIG. 3- TYPICAL FORWORD CHARACTERISTICS PER LGE 100 100 NUMBER OF CYCLES AT 60 Hz FIG. 4- TYPICAL REVERSE CHARACTERISTICS PER LEG TA=125℃ INSTANTANEOUS FORWARD CURRENT, (A ) INSTANTANEOUS REVERSE CURRENT, (A) 10 10 1 1 0.1 0.1 T A=25℃ 0.01 0.01 0.6 0.8 1.0 1.2 1.4 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE,(V) FIG. 5- TYPICAL JUNCTION CAPACITANCE PER LEG 1000 100 PERCENT OF RATED PEAK REVERSE V OLTAGE,(V ) FIG. 6- TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE (℃/W) JUNCTION CAPACITANCE, (pF) 100 1 10 1 1 10 100 0.1 0.01 0.1 1 10 REVRESE VOLTAGE,( V) T, HEATING TIME (SEC.) E-mail: sales@cnmic.com Web Site: www.cnmic.com