GBJ808

SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER GBJ8005 THRU GBJ810 FEATURES • • • • • VOLTAGE RANGE CURRENT 50 to 1000 Volts 8.0 Amperes GBJ O 19.7-20.3 Plastic package has UL Flammability Glassification 94V-0 Glass passivated chip junctions High case dielectric strength of 1500 VRMS High surge current capability High temperature soldering guaranteed 260℃/10 seconds, 0.375”(9.5mm) lead length 29.7-30.3 3.0×45 O 4.4-4.8 3.4-3.8 - 3 .4 .1 φ3 5.0 • • • • • Case: molded plastic body Terminal: Plated leads solderable per MIL-STD-750 Method 2026 Mounting position: Any (Note 3) Mounting Torque: 6 in – 1bs max. Weight: 0.26 ounce, 7.4 gram 3.8-4.2 17.0-18.0 MECHANICAL DATA 2.5±0.2 2.0-2.4 2.7-3.1 0.9-1.1 9.8-10.2 7.3-7.7 7.3-7.7 0.6-0.8 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% GBJ SYMBOLS GBJ 8005 801 GBJ 802 GBJ 804 GBJ 806 GBJ 808 GBJ 810 Maximum Reverse Peak Repetitive Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, At TC=100℃ (Note 1) Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per bridge element 4.0A TA=25℃ Maximum DC Reverse Current at rated DC blocking voltage per element TA=125℃ Typical Junction Capacitance, per let (Note 2) Typical Thermal Resistance (Note 4) Operating Junction Temperature Range Storage Temperature Range VRRM VRMS VDC I(AV) IFSM I2 t VF IR CJ RJA TJ TSTG 50 35 50 100 70 100 200 140 200 400 280 400 8.0 170 166 1.0 5.0 500 600 420 600 800 560 800 1000 700 100 10.8-11.2 UNIT Volts Volts Volts Amps Amps A2s Volts μA 211.0 3.5 (-55 to +150) (-55 to +150) 94.0 pF ℃/W ℃ ℃ Notes: 1. Unit case mounted on 3.2×3.2×0.12” thick (8.2×8.2×0.3cm) A1. Plate heatdink 2. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts 3. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat Transfer with #6 screws 4.Unit mounted in free air, no heat sink on P.C.B. 0.5×0.5”(12×12mm) copper pads 0.375” (9.5mm) lead length E-mail: sales@cnmic.com Web Site: www.cnmic.com SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER GBJ8005 THRU GBJ810 VOLTAGE RANGE CURRENT 50 to 1000 Volts 8.0 Amperes RATINGS AND CHARACTERISTIC CURVES GBJ8005 THRU GBJ810 FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT AVERAGE FORWARD OUTPUT CURRENT (A) 10 250 FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG TJ =150℃ 8.3ms Single Half Sine-Wave (JEDEC Method ) 60 Hz Resistive or Inductive Load PEAK FORWARD SURGE, CURRENT,(A) 8.0 200 6.0 Heat-Sink Mounting,on 3.2× 3.2×0.12"Thk (8.2×8.2×0.3cm)AL.Plate 150 4.0 100 2.0 50 0 0 20 50 80 100 120 150 0 1 10 100 CASE TEMPERATURE, ℃ FIG. 3- TYPICAL FORWORD CHARACTERISTICS PER LGE 100 500 100 NUMBER OF CYCLES AT 60 Hz FIG. 4- TYPICAL REVERSE CHARACTERISTICS PER LEG TJ =150℃ INSTANTANEOUS FORWARD CURRENT , (A) 10 INSTANTANEOUS REVERSE CURRENT, (A) 10 TJ =125℃ 1 1 50-400V 600-1000V 0.1 TJ=25℃ Pulse width=300μ S 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.1 TJ =25℃ 0.01 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE,(V) FIG. 5- TYPICAL JUNCTION CAPACITANCE PER LEG 1000 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG. 6- TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG 100 TRANSIENT THERMAL IMPEDANCE (℃/W) JUNCTION CAPACITANCE, (pF) TJ=25℃ f=1.0MHz Vsig=50mVp-p 10 100 1 50-400V 600-1000V 10 0.1 1 10 100 0.1 0.01 0.1 1 10 100 REVRESE VOLTAGE,(V) T, HEATING TIME (SEC.) E-mail: sales@cnmic.com Web Site: www.cnmic.com