SFF163C

SUPER FAST GLASS PASSIVATED RECTIFIER SFF161C THRU SFF166C FEATURES • • • • • • • VOLTAGE RANGE CURRENT 50 to 400 Volts 16.0 Ampere ITO-220AB • Super fast switching speed Glass passivated chip junction Low power loss, high efficiency Low leakage High surge capacity High temperature soldering guaranteed 250℃/10 second, 0.16″(4.06mm) lead length Also available with common Anode, add an “A” suffix, i.e. SFF161CA, add as a doubler, add a “D” suffix, i.e. SFF161CD Also available in the single chip version, SFF81 MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Lead: Solderable per MIL-STD-202E method 208C Polarity: as marked Mounting position: Any, 5 in-lbs Torque Max Weight: 0.08ounce, 2.24 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SFF SFF SYMBOLS 161C 162C Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 • • • Maximum Average Forward Rectified Current At Tc=100℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage per at 8.0A Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage at TA = 125℃ Maximum Reverse Recovery Time Test conditions IF =0.5A, IR =1.0A, IRR =0.25A Typical Junction Capacitance ( Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance (Note 1) Operating Junction Temperature Storage Temperature Range SFF 163C 150 105 150 16.0 125 SFF 164C 200 140 200 SFF 165C 300 210 300 SFF 166C 400 280 400 UNIT Volts Volts Volts Amps Amps I(AV) IFSM VF IR trr CJ RθJC TJ TSTG 35 0.975 1.4 10 500 50 40 3.0 (-55 to +150) (-55 to +150) Volts µA nS pF ℃/W ℃ ℃ Notes: 1. Unit mounted on heatsink E-mail: sales@cnmic.com Web Site: www.cnmic.com SUPER FAST GLASS PASSIVATED RECTIFIER SFF161C THRU SFF166C VOLTAGE RANGE CURRENT 50 to 400 Volts 16.0 Ampere RATING AND CHRACTERISTIC CURVES SFF161C THRU SFF166C FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, 24 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE 20 150 16 CURRENT, (A) 8.3ms Single Half Sine-Wave (JEDEC Method) T= T jmax 100 (A) 12 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 8.0 50 4.0 0 0 25 50 75 100 125 150 175 0 1 1 Cycle 2 4 6 8 10 20 40 60 100 AMBIENT TEMPERATURE, (° C) NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 100 TJ =125° C 100 INSTANTANEOUS FORWARD CURRENT, INSTANTANEOUS REVERSE CURRENT, (μA) 10 50/ 20 10 30 0/ 40 (A) /1 0 0/1 0V 0V 1.0 1.0 50 TJ =25° C TJ =25° C Pulse Width=300us 1% Duty Cycle 0.1 0.4 0.8 1.2 1.6 0.1 INSTANTANEOUS FORWARD VOLTAGE,(V) 0.01 0 20 40 60 80 100 120 140 FIG.5-TYPICAL JUNCTION CAPACITANCE PER LEG 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) JUNCTION CAPACITANCE,(pF) F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE (-) 10 (+) 25 Vdc (approx.) (-) TJ =25° C f=1MHz Vsig=50mVp-p D.U.T. PULSE GENERATIOR (NOTE 2) (+) OSCILLOSCOPE (NOTE 1) +0.5A 0 -0.25A 1Ω NON INDUCTIVE -1.0A 1cm 1 0.1 1.0 10 100 REVERSE VOLTAGE,(V) NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms SET TIME BASE FOR 50/100ns/cm E-mail: sales@cnmic.com Web Site: www.cnmic.com