93LC86-ISN

93LC76/86 8K/16K 2.5V Microwire® Serial EEPROM FEATURES • Single supply with programming operation down to 2.5V • Low power CMOS technology - 1 mA active current typical - 5 µA standby current (typical) at 3.0V • ORG pin selectable memory configuration 1024 x 8 or 512 x 16 bit organization (93LC76) 2048 x 8 or 1024 x 16 bit organization (93LC86) • Self-timed ERASE and WRITE cycles (including auto-erase) • Automatic ERAL before WRAL • Power on/off data protection circuitry • Industry standard 3-wire serial I/O • Device status signal during ERASE/WRITE cycles • Sequential READ function • 10,000,000 ERASE/WRITE cycles guaranteed • Data retention > 200 years • 8-pin PDIP/SOIC package • Temperature ranges available - Commercial (C) 0°C to +70°C - Industrial (I) -40°C to +85°C PACKAGE TYPES DIP Package CS CLK DI DO 1 2 3 4 8 7 6 5 VCC PE ORG VSS 93LC76/86 SOIC Package 1 2 3 4 8 7 6 5 93LC76/86 CS CLK DI DO VCC PE ORG VSS BLOCK DIAGRAM VCC VSS DESCRIPTION The Microchip Technology Inc. 93LC76/86 are 8K and 16K low voltage serial Electrically Erasable PROMs. The device memory is configured as x8 or x16 bits depending on the ORG pin setup. Advanced CMOS technology makes these devices ideal for low power non-volatile memory applications. These devices also have a Program Enable (PE) pin to allow the user to write protect the entire contents of the memory array. The 93LC76/86 is available in standard 8-pin DIP and 8-pin surface mount SOIC packages. Memory Array Address Decoder Address Counter Data Register DI Output Buffer DO PE CS Mode Decode Logic CLK Clock Generator Microwire is a registered trademark of National Semiconductor Incorporated. © 1996 Microchip Technology Inc. Preliminary This document was created with FrameMaker 4 0 4 DS21131C-page 1 93LC76/86 1.0 1.1 ELECTRICAL CHARACTERISTICS Maximum Ratings* 1.2 AC Test Conditions AC Waveform: VLO = 2.0V VHI = Vcc - 0.2V VHI = 4.0V for (Note 1) (Note 2) VCC ...................................................................................7.0V All inputs and outputs w.r.t. VSS ............... -0.6V to Vcc +1.0V Storage temperature ..................................... -65˚C to +150˚C Ambient temp. with power applied................. -65˚C to +125˚C Soldering temperature of leads (10 seconds) ............. +300˚C ESD protection on all pins................................................4 kV *Notice: Stresses above those listed under “Maximum ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability Timing Measurement Reference Level Input Output Note 1: For VCC ≤ 4.0V 2: For VCC > 4.0V 0.5 VCC 0.5 VCC TABLE 1-1: Name CS CLK DI DO VSS ORG PE VCC PIN FUNCTION TABLE Function Chip Select Serial Data Clock Serial Data Input Serial Data Output Ground Memory Configuration Program Enable Power Supply TABLE 1-2: DC CHARACTERISTICS Applicable over recommended operating ranges shown below unless otherwise noted: VCC = +2.5V to +6.0V Commercial (C): Tamb = 0˚C to +70˚C Industrial (I): Tamb = -40˚C to +85˚C Parameter High level input voltage Low level input voltage Low level output voltage High level output voltage Input leakage current Output leakage current Pin capacitance (all inputs/outputs) Operating current Symbol VIH1 VIH2 VIL1 VIL2 VOL1 VOL2 VOH1 VOH2 ILI ILO CINT ICC write ICC read Min. 2.0 0.7 VCC -0.3 -0.3 — — 2.4 VCC-0.2 -10 -10 — — — Max. VCC +1 VCC +1 0.8 0.2 VCC 0.4 0.2 — — 10 10 7 Units V V V V V V V V µA µA pF Conditions VCC ≥ 2.7V VCC < 2.7V VCC ≥ 2.7V VCC < 2.7V IOL = 2.1 mA; VCC = 4.5V IOL =100 µA; VCC = VCC Min. IOH = -400 µA; VCC = 4.5V IOH = -100 µA; VCC = VCC Min. VIN = 0.1V to VCC VOUT = 0.1V to VCC (Note Note:) Tamb = +25˚C, FCLK = 1 MHz VCC = 5.5V FCLK = 3 MHz; VCC = 5.5V FCLK = 1 MHz; VCC = 3.0V CLK = CS = 0V; VCC = 5.5V CLK = CS = 0V; VCC = 3.0V 3 mA 1 mA 500 µA µA — 100 Standby current ICCS 30 µA Note: This parameter is periodically sampled and not 100% tested. DS21131C-page 2 Preliminary © 1996 Microchip Technology Inc. 93LC76/86 TABLE 1-3: AC CHARACTERISTICS Applicable over recommended operating ranges shown below unless otherwise noted: VCC = +2.5V to +6.0V Commercial (C): Tamb = 0˚C to +70˚C Industrial (I): Tamb = -40˚C to +85˚C Parameter Clock frequency Clock high time Clock low time Chip select setup time Chip select hold time Chip select low time Data input setup time Data input hold time Data output delay time Data output disable time Status valid time Program cycle time Symbol FCLK TCKH TCKL TCSS TCSH TCSL TDIS TDIH TPD TCZ TSV TWC TEC TWL — Min. — 200 300 100 200 50 100 0 250 50 100 50 100 — — — — — — 10M Max. 3 2 — — — — — — — 100 250 100 500 200 300 5 15 30 — Units MHz MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ms ms ms cycles Conditions 4.5V 2.5V 4.5V 2.5V 4.5V 2.5V 4.5V 2.5V ≤ VCC ≤ 6.0V ≤ VCC < 4.5V ≤ VCC ≤ 6.0V ≤ VCC < 4.5V ≥ VCC ≤ 6.0V ≤ VCC < 4.5V ≤ VCC ≤ 6.0V, Relative to CLK ≤ VCC < 4.5V, Relative to CLK Endurance Relative to CLK 4.5V ≤ VCC ≤ 6.0V, Relative to CLK 2.5V ≤ VCC