PIC24FV32KA301

PIC24FV32KA304 Data Sheet 20/28/44/48-Pin, General Purpose, 16-Bit Flash Microcontrollers with XLP Technology  2011 Microchip Technology Inc. DS39995B Note the following details of the code protection feature on Microchip devices: • • • Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” • • Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2011, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-61341-079-0 Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS39995B-page 2  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 20/28/44/48-Pin, General Purpose, 16-Bit Flash Microcontrollers with XLP Technology Power Management Modes: • • • • • Run – CPU, Flash, SRAM and Peripherals On Doze – CPU Clock Runs Slower than Peripherals Idle – CPU Off, Flash, SRAM and Peripherals On Sleep – CPU, Flash and Peripherals Off and SRAM on Deep Sleep – CPU, Flash, SRAM and Most Peripherals Off; Multiple Autonomous Wake-up Sources • Low-Power Consumption: - Run mode currents down to 8 μA, typical - Idle mode currents down to 2.2 μA, typical - Deep Sleep mode currents down to 20 nA, typical - Real-Time Clock/Calendar currents down to 700 nA, 32 kHz, 1.8V - Watchdog Timer 500 nA, 1.8V typical Analog Features: • 12-Bit, up to 16-Channel Analog-to-Digital Converter: - 100 ksps conversion rate - Conversion available during Sleep and Idle - Auto-sampling timer-based option for Sleep and Idle modes - Wake on auto-compare option • Dual Rail-to-Rail Analog Comparators with Programmable Input/Output Configuration • On-Chip Voltage Reference • Internal Temperature Sensor • Charge Time Measurement Unit (CTMU): - Used for capacitance sensing, 16 channels - Time measurement, down to 200 ps resolution - Delay/pulse generation, down to 1 ns resolution High-Performance CPU: • Modified Harvard Architecture • Up to 16 MIPS Operation @ 32 MHz • 8 MHz Internal Oscillator with 4x PLL Option and Multiple Divide Options • 17-Bit by 17-Bit Single-Cycle Hardware Multiplier • 32-Bit by 16-Bit Hardware Divider 16-Bit x 16-Bit Working Register Array • C Compiler Optimized Instruction Set Architecture Special Microcontroller Features: • Wide Operating Voltage Range: - 1.8V to 3.6V (PIC24F devices) - 2.0V to 5.5V (PIC24FV devices) • Low Power Wake-up Sources and Supervisors: - Ultra-Low Power Wake-up (ULPWU) for Sleep/Deep Sleep - Low-Power Watchdog Timer (DSWDT) for Deep Sleep - Extreme Low-Power Brown-out Reset (DSBOR) for Deep Sleep, LPBOR for all other modes • System Frequency Range Declaration bits: - Declaring the frequency range optimizes the current consumption. • Standard Watchdog Timer (WDT) with On-Chip, Low-Power RC Oscillator for Reliable Operation • Programmable High/Low-Voltage Detect (HLVD) • Standard Brown-out Reset (BOR) with 3 Programmable Trip Points that can be Disabled in Sleep • High-Current Sink/Source (18 mA/18 mA) on All I/O Pins • Flash Program Memory: - Erase/write cycles: 10,000 minimum - 40 years’ data retention minimum • Data EEPROM: - Erase/write cycles: 100,000 minimum - 40 years’ data retention minimum • Fail-Safe Clock Monitor • Programmable Reference Clock Output • Self-Programmable under Software Control • In-Circuit Serial Programming™ (ICSP™) and In-Circuit Debug (ICD) via 2 Pins Peripheral Features: • Hardware Real-Time Clock and Calendar (RTCC): - Provides clock, calendar and alarm functions - Can run in Deep Sleep mode - Can use 50/60 Hz power line input as clock source • Programmable 32-bit Cyclic Redundancy Check (CRC) • Multiple Serial Communication modules: - Two 3-/4-wire SPI modules - Two I2C™ modules with multi-master/slave support - Two UART modules supporting RS-485, RS-232, LIN/J2602, IrDA® • Five 16-Bit Timers/Counters with Programmable Prescaler: - Can be paired as 32-bit timers/counters • Three 16-Bit Capture Inputs with Dedicated Timers • Three 16-Bit Compare/PWM Output with Dedicated Timers • Configurable Open-Drain Outputs on Digital I/O Pins • Up to Three External Interrupt Sources  2011 Microchip Technology Inc. DS39995B-page 3 PIC24FV32KA304 FAMILY Compare/PWM Output Comparators CTMU (ch) 12 12 13 13 16 16 Memory Capture Input Timers 16-Bit EE Data (bytes) SRAM (bytes) PIC24F Device Flash Program (bytes) Pins 12-Bit A/D (ch) UART w/ IrDA® RTCC Y Y Y Y Y Y I2C™ 2 2 2 2 2 2 SPI 2 2 2 2 2 2 PIC24FV16KA301 /PIC24F16KA301 PIC24FV32KA301 /PIC24F32KA301 PIC24FV16KA302 /PIC24F16KA302 PIC24FV32KA302 /PIC24F32KA302 PIC24FV16KA304 /PIC24F16KA304 PIC24FV32KA304 /PIC24F32KA304 20 20 28 28 44 44 16K 32K 16K 32K 16K 32K 2K 2K 2K 2K 2K 2K 512 512 512 512 512 512 5 5 5 5 5 5 3 3 3 3 3 3 3 3 3 3 3 3 2 2 2 2 2 2 12 12 13 13 16 16 3 3 3 3 3 3 DS39995B-page 4  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Pin Diagrams 20-Pin SPDIP/SSOP/SOIC(1) MCLR/RA5 RA0 RA1 RB0 RB1 RB2 RA2 RA3 RB4 RA4 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VDD VSS RB15 RB14 RB13 RB12 RA6 OR VCAP RB9 RB8 RB7 24FVXXKA301 Pin Features Pin PIC24FVXXKA301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MCLR/VPP/RA5 PGEC2/VREF+/CVREF+/AN0/C3INC/SCK2/CN2/RA0 PGED2/CVREF-/VREF-/AN1/SDO2/CN3/RA1 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/SDI2/ OC2/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/OC3/CTED12/CN5/RB1 AN4/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 OSCI/AN13/C1INB/C2IND/CLKI/CN30/RA2 OSCO/AN14/C1INA/C2INC/CLKO/CN29/RA3 PGED3/SOSCI/AN15/U2RTS/CN1/RB4 PGEC3/SOSCO/SCLKI/U2CTS/CN0/RA4 U1TX/C2OUT/OC1/IC1/CTED1/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 VCAP AN12/LVDIN/SCK1/SS2/IC3/CTED2/INT2/CN14/RB12 AN11/SDO1/OCFB/CTPLS/CN13/RB13 CVREF/AN10/C3INB/RTCC/SDI1/C1OUT/OCFA/CTED5/INT1/ CN12/RB14 AN9/C3INA/SCL2/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD MCLR/VPP/RA5 PGEC2/VREF+/CVREF+/AN0/C3INC/SCK2/CN2/RA0 PGED2/CVREF-/VREF-/AN1/SDO2/CN3/RA1 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/SDI2/ OC2/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/OC3/CTED12/CN5/RB1 AN4/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 OSCI/AN13/C1INB/C2IND/CLKI/CN30/RA2 OSCO/AN14/C1INA/C2INC/CLKO/CN29/RA3 PGED3/SOSCI/AN15/U2RTS/CN1/RB4 PGEC3/SOSCO/SCLKI/U2CTS/CN0/RA4 U1TX/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 C2OUT/OC1/IC1/CTED1/INT2/CN8/RA6 AN12/LVDIN/SCK1/SS2/IC3/CTED2/CN14/RB12 AN11/SDO1/OCFB/CTPLS/CN13/RB13 CVREF/AN10/C3INB/RTCC/SDI1/C1OUT/OCFA/CTED5/INT1/ CN12/RB14 AN9/C3INA/SCL2/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD PIC24FXXKA301 Legend: Note 1: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. PIC24F32KA304 device pins have a maximum voltage of 3.6V and are not 5V tolerant.  2011 Microchip Technology Inc. 24FXXKA301 DS39995B-page 5 PIC24FV32KA304 FAMILY Pin Diagrams 28-Pin SPDIP/SSOP/SOIC(1,2) MCLR/RA5 RA0 RA1 RB0 RB1 RB2 RB3 VSS RA2 RA3 RB4 RA4 VDD RB5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VDD VSS RB15 RB14 RB13 RB12 RB11 RB10 RA6 OR VCAP RA7 RB9 RB8 RB7 RB6 Pin PIC24FVXXKA302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 MCLR/VPP/RA5 VREF+/CVREF+/AN0/C3INC/CTED1/CN2/RA0 CVREF-/VREF-/AN1/CN3/RA1 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/RB3 VSS OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 VDD PGED3/ASDA(1)/SCK2/CN27/RB5 PGEC3/ASCL(1)/SDO2/CN24/RB6 U1TX/C2OUT/OC1/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 SDI2/IC1/CTED3/CN9/RA7 VCAP PGED2/SDI1/OC3/CTED11/CN16/RB10 PGEC2/SCK1/OC2/CTED9/CN15/RB11 AN12/LVDIN/SS2/IC3/CTED2/INT2/CN14/RB12 AN11/SDO1/OCFB/CTPLS/CN13/RB13 MCLR/VPP/RA5 VREF+/CVREF+/AN0/C3INC/CTED1/CN2/RA0 CVREF-/VREF-/AN1/CN3/RA1 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/RB3 VSS OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 VDD PGED3/ASDA(1)/SCK2/CN27/RB5 PGEC3/ASCL(1)/SDO2/CN24/RB6 U1TX/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 SDI2/IC1/CTED3/CN9/RA7 C2OUT/OC1/CTED1/INT2/CN8/RA6 PGED2/SDI1/OC3/CTED11/CN16/RB10 PGEC2/SCK1/OC2/CTED9/CN15/RB11 AN12/LVDIN/SS2/IC3/CTED2/CN14/RB12 AN11/SDO1/OCFB/CTPLS/CN13/RB13 PIC24FXXKA302 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/RB14 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/ RB14 AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD Legend: Note 1: 2: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. Alternative multiplexing for SDA1(ASDA1) and SCL1 (ASCL1) when the I2CSEL Configuration bit is set. PIC24F32KA304 device pins have a maximum voltage of 3.6V and are not 5V tolerant PIC24FVXXKA302 PIC24FXXKA302 Pin Features DS39995B-page 6  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Pin Diagrams 28-Pin QFN(1,2,3) RA1 RA0 MCLR/RA5 VDD VSS RB15 RB14 28 27 26 25 24 23 22 RB0 RB1 RB2 RB3 VSS RA2 RA3 1 2 3 4 5 6 7 21 20 19 18 17 16 15 RB13 RB12 RB11 RB10 RA6 OR VCAP RA7 RB9 24FVXXKA302 24FXXKA302 8 9 10 11 12 13 14 RB4 RA4 VDD RB5 RB6 RB7 RB8 Pin Features Pin PIC24FVXXKA302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/RB3 VSS OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 VDD PGED3/ASDA1(2)/SCK2/CN27/RB5 PGEC3/ASCL1(2)/SDO2/CN24/RB6 U1TX/C2OUT/OC1/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 SDI2/IC1/CTED3/CN9/RA7 VCAP PGED2/SDI1/OC3/CTED11/CN16/RB10 PGEC2/SCK1/OC2/CTED9/CN15/RB11 AN12/LVDIN/SS2/IC3/CTED2/INT2/CN14/RB12 AN11/SDO1/OCFB/CTPLS/CN13/RB13 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/ RB14 AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD MCLR/VPP/RA5 VREF+/CVREF+/AN0/C3INC/CTED1/CN2/RA0 CVREF-/VREF-/AN1/CN3/RA1 PIC24FXXKA302 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/RB3 VSS OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 VDD PGED3/ASDA1(2)/SCK2/CN27/RB5 PGEC3/ASCL1(2)/SDO2/CN24/RB6 U1TX/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 SDI2/IC1/CTED3/CN9/RA7 C2OUT/OC1/CTED1/INT2/CN8/RA6 PGED2/SDI1/OC3/CTED11/CN16/RB10 PGEC2/SCK1/OC2/CTED9/CN15/RB11 AN12/LVDIN/SS2/IC3/CTED2/CN14/RB12 AN11/SDO1/OCFB/CTPLS/CN13/RB13 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/ RB14 AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD MCLR/VPP/RA5 VREF+/CVREF+/AN0/C3INC/CTED1/CN2/RA0 CVREF-/VREF-/AN1/CN3/RA1 Legend: Note 1: 2: 3: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. Exposed pad on underside of device is connected to VSS. Alternative multiplexing for SDA1 (ASDA1) and SCL1 (ASCL1) when the I2CSEL Configuration bit is set. PIC24F32KA304 device pins have a maximum voltage of 3.6V and are not 5V tolerant.  2011 Microchip Technology Inc. DS39995B-page 7 PIC24FV32KA304 FAMILY Pin Diagrams Pin Features Pin 44-Pin TQFP/QFN(1,2,3) 1 2 3 RB8 RB7 RB6 RB5 VDD VSS RC5 RC4 RC3 RA9 RA4 4 5 RB4 RA8 RA3 RA2 VSS VDD RC2 RC1 RC0 RB3 RB2 6 7 8 9 10 11 12 13 14 PIC24FVXXKA304 PIC24FXXKA304 SDA1/T1CK/U1RTS/CTED4/CN21/ SDA1/T1CK/U1RTS/CTED4/CN21/ RB9 RB9 U1RX/CN18/RC6 U1TX/CN17/RC7 OC2/CN20/RC8 IC2/CTED7/CN19/RC9 IC1/CTED3/CN9/RA7 VCAP PGED2/SDI1/CTED11/CN16/RB10 PGEC2/SCK1/CTED9/CN15/RB11 AN12/LVDIN/CTED2/INT2/CN14/ RB12 AN11/SDO1/CTPLS/CN13/RB13 OC3/CN35/RA10 IC3/CTED8/CN36/RA11 U1RX/CN18/RC6 U1TX/CN17/RC7 OC2/CN20/RC8 IC2/CTED7/CN19/RC9 IC1/CTED3/CN9/RA7 C2OUT/OC1/CTED1/INT2/CN8/RA6 PGED2/SDI1/CTED11/CN16/RB10 PGEC2/SCK1/CTED9/CN15/RB11 AN12/LVDIN/CTED2/CN14/RB12 AN11/SDO1/CTPLS/CN13/RB13 OC3/CN35/RA10 IC3/CTED8/CN36/RA11 12 13 14 15 16 17 18 19 20 21 22 RB9 RC6 RC7 RC8 RC9 RA7 RA6 OR VCAP RB10 RB11 RB12 RB13 1 2 3 4 5 6 7 8 9 10 11 44 43 42 41 40 39 38 37 36 35 34 PIC24FVXXKA304 PIC24FXXKA304 33 32 31 30 29 28 27 26 25 24 23 RA10 RA11 RB14 RB15 VSS VDD MCLR/RA5 RA0 RA1 RB0 RB1 CVREF/AN10/C3INB/RTCC/ CVREF/AN10/C3INB/RTCC/ C1OUT/OCFA/CTED5/INT1/CN12/ C1OUT/OCFA/CTED5/INT1/CN12/ RB14 RB14 AN9/C3INA/T3CK/T2CK/REFO/ SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD MCLR/VPP/RA5 VREF+/CVREF+/AN0/C3INC/ CTED1/CN2/RA0 CVREF-/VREF-/AN1/CN3/RA1 AN9/C3INA/T3CK/T2CK/REFO/ SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD MCLR/VPP/RA5 VREF+/CVREF+/AN0/C3INC/CN2/ RA0 CVREF-/VREF-/AN1/CN3/RA1 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 PGED1/AN2/ULPWU/CTCMP/ PGED1/AN2/ULPWU/CTCMP/C1IND/ C1IND/C2INB/C3IND/U2TX/CN4/RB0 C2INB/C3IND/U2TX/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/ CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/ T4CK/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/ RB3 AN6/CN32/RC0 AN7/CN31/RC1 AN8/CN10/RC2 VDD VSS OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 OCFB/CN33/RA8 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 SS2/CN34/RA9 SDI2/CN28/RC3 SDO2/CN25/RC4 SCK2/CN26/RC5 VSS VDD PGED3/ASDA1(2)/CN27/RB5 PGEC3/ASCL1(2)/CN24/RB6 INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/ CN22/RB8 PGEC1/AN3/C1INC/C2INA/U2RX/ CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/ T4CK/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/RB3 AN6/CN32/RC0 AN7/CN31/RC1 AN8/CN10/RC2 VDD VSS OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 OCFB/CN33/RA8 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 SS2/CN34/RA9 SDI2/CN28/RC3 SDO2/CN25/RC4 SCK2/CN26/RC5 VSS VDD PGED3/ASDA1(2)/CN27/RB5 PGEC3/ASCL1(2)/CN24/RB6 INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/ CN22/RB8 Legend: Note 1: 2: 3: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. Exposed pad on underside of device is connected to VSS. Alternative multiplexing for SDA1 (ASDA1) and SCL1 (ASCL1) when the I2CSEL Configuration bit is set. PIC24F32KA304 device pins have a maximum voltage of 3.6V and are not 5V tolerant. DS39995B-page 8  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Pin Diagrams Pin Features 48-Pin UQFN(1,2,3) Pin PIC24FVXXKA304 1 2 SDA1/T1CK/U1RTS/CTED4/CN21/RB9 U1RX/CN18/RC6 U1TX/CN17/RC7 OC2/CN20/RC8 IC2/CTED7/CN19/RC9 IC1/CTED3/CN9/RA7 VCAP n/c PGED2/SDI1/CTED11/CN16/RB10 PGEC2/SCK1/CTED9/CN15/RB11 AN12/LVDIN/CTED2/INT2/CN14/RB12 AN11/SDO1/CTPLS/CN13/RB13 OC3/CN35/RA10 IC3/CTED8/CN36/RA11 PIC24FXXKA304 SDA1/T1CK/U1RTS/CTED4/CN21/ RB9 U1RX/CN18/RC6 U1TX/CN17/RC7 OC2/CN20/RC8 IC2/CTED7/CN19/RC9 IC1/CTED3/CN9/RA7 INT2/RA6 n/c PGED2/SDI1/CTED11/CN16/RB10 PGEC2/SCK1/CTED9/CN15/RB11 AN12/LVDIN/CTED2/CN14/RB12 AN11/SDO1/CTPLS/CN13/RB13 OC3/CN35/RA10 IC3/CTED8/CN36/RA11 RB8 RB7 RB6 RB5 n/c VDD VSS RC5 RC4 RC3 RA9 RA4 3 4 5 RB4 RA8 RA3 RA2 n/c VSS VDD RC2 RC1 RC0 RB3 RB2 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 RB9 RC6 RC7 RC8 RC9 RA7 RA6 n/c RB10 RB11 RB12 RB13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 PIC24FVXXKA304 PIC24FXXKA304 36 35 34 33 32 31 30 29 28 27 26 25 RA10 RA11 RB14 RB15 VSS/AVSS VDD/AVDD MCLR/RA5 n/c RA0 RA1 RB0 RB1 CVREF/AN10/C3INB/RTCC/ CVREF/AN10/C3INB/RTCC/C1OUT/ C1OUT/OCFA/CTED5/INT1/CN12/RB14 OCFA/CTED5/INT1/CN12/RB14 AN9/C3INA/T3CK/T2CK/REFO/ SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD MCLR/RA5 n/c VREF+/CVREF+/AN0/C3INC/ CTED1/CN2/RA0 CVREF-/VREF-/AN1/CN3/RA1 PGED1/AN2/ULPWU/CTCMP/C1IND/ C2INB/C3IND/U2TX/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/ CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/ T4CK/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/RB3 AN6/CN32/RC0 AN7/CN31/RC1 AN8/CN10/RC2 VDD VSS n/c OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 OCFB/CN33/RA8 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 SS2/CN34/RA9 SDI2/CN28/RC3 SDO2/CN25/RC4 SCK2/CN26/RC5 VSS VDD n/c PGED3/ASDA1(2)/CN27/RB5 PGEC3/ASCL1 /CN24/RB6 C2OUT/OC1/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/ CN22/RB8 (2) AN9/C3INA/T3CK/T2CK/REFO/ SS1/CTED6/CN11/RB15 VSS/AVSS VDD/AVDD MCLR/RA5 n/c VREF+/CVREF+/AN0/C3INC/ CTED1/CN2/RA0 CVREF-/VREF-/AN1/CN3/RA1 PGED1/AN2/ULPWU/CTCMP/C1IND/ C2INB/C3IND/U2TX/CN4/RB0 PGEC1/AN3/C1INC/C2INA/U2RX/ CTED12/CN5/RB1 AN4/C1INB/C2IND/SDA2/T5CK/ T4CK/CTED13/CN6/RB2 AN5/C1INA/C2INC/SCL2/CN7/RB3 AN6/CN32/RC0 AN7/CN31/RC1 AN8/CN10/RC2 VDD VSS n/c OSCI/AN13/CLKI/CN30/RA2 OSCO/AN14/CLKO/CN29/RA3 OCFB/CN33/RA8 SOSCI/AN15/U2RTS/CN1/RB4 SOSCO/SCLKI/U2CTS/CN0/RA4 SS2/CN34/RA9 SDI2/CN28/RC3 SDO2/CN25/RC4 SCK2/CN26/RC5 VSS VDD n/c PGED3/ASDA1(2)/CN27/RB5 PGEC3/ASCL1(2)/CN24/RB6 C2OUT/OC1/INT0/CN23/RB7 SCL1/U1CTS/C3OUT/CTED10/ CN22/RB8 Legend: Note 1: 2: 3: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. Exposed pad on underside of device is connected to VSS. Alternative multiplexing for SDA1 (ASDA1) and SCL1 (ASCL1) when the I2CSEL Configuration bit is set. PIC24F32KA3XX device pins have a maximum voltage of 3.6V and are not 5V tolerant. 37 38 39 40 41 42 43 44 45 46 47 48  2011 Microchip Technology Inc. DS39995B-page 9 PIC24FV32KA304 FAMILY Table of Contents 1.0 Device Overview ........................................................................................................................................................................ 13 2.0 Guidelines for Getting Started with 16-Bit Microcontrollers ........................................................................................................ 25 3.0 CPU ........................................................................................................................................................................................... 31 4.0 Memory Organization ................................................................................................................................................................. 37 5.0 Flash Program Memory .............................................................................................................................................................. 59 6.0 Data EEPROM Memory ............................................................................................................................................................. 67 7.0 Resets ........................................................................................................................................................................................ 73 8.0 Interrupt Controller ..................................................................................................................................................................... 79 9.0 Oscillator Configuration ............................................................................................................................................................ 117 10.0 Power-Saving Features ............................................................................................................................................................ 127 11.0 I/O Ports ................................................................................................................................................................................... 139 12.0 Timer1 ..................................................................................................................................................................................... 143 13.0 Timer2/3 and Timer4/5 ............................................................................................................................................................. 145 14.0 Input Capture with Dedicated Timers ....................................................................................................................................... 151 15.0 Output Compare with Dedicated Timers .................................................................................................................................. 155 16.0 Serial Peripheral Interface (SPI)............................................................................................................................................... 165 17.0 Inter-Integrated Circuit™ (I2C™) .............................................................................................................................................. 173 18.0 Universal Asynchronous Receiver Transmitter (UART) ........................................................................................................... 181 19.0 Real-Time Clock and Calendar (RTCC) .................................................................................................................................. 189 20.0 32-Bit Programmable Cyclic Redundancy Check (CRC) Generator ........................................................................................ 203 21.0 High/Low-Voltage Detect (HLVD)............................................................................................................................................. 209 22.0 12-Bit A/D Converter with Threshold Detect ............................................................................................................................ 211 23.0 Comparator Module.................................................................................................................................................................. 225 24.0 Comparator Voltage Reference................................................................................................................................................ 229 25.0 Charge Time Measurement Unit (CTMU) ................................................................................................................................ 231 26.0 Special Features ...................................................................................................................................................................... 239 27.0 Development Support............................................................................................................................................................... 251 28.0 Instruction Set Summary .......................................................................................................................................................... 255 29.0 Electrical Characteristics .......................................................................................................................................................... 263 30.0 Packaging Information.............................................................................................................................................................. 289 Appendix A: Revision History............................................................................................................................................................. 311 Index .................................................................................................................................................................................................. 313 The Microchip Web Site ..................................................................................................................................................................... 317 Customer Change Notification Service .............................................................................................................................................. 317 Customer Support .............................................................................................................................................................................. 317 Reader Response .............................................................................................................................................................................. 318 Product Identification System............................................................................................................................................................. 319 DS39995B-page 10  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products.  2011 Microchip Technology Inc. DS39995B-page 11 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 12  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 1.0 DEVICE OVERVIEW 1.1.2 POWER-SAVING TECHNOLOGY This document contains device-specific information for the following devices: • • • • • • PIC24FV16KA301, PIC24F16KA301 PIC24FV16KA302, PIC24F16KA302 PIC24FV16KA304, PIC24F16KA304 PIC24FV32KA301, PIC24F32KA301 PIC24FV32KA302, PIC24F32KA302 PIC24FV32KA304, PIC24F32KA304 All of the devices in the PIC24FV32KA304 family incorporate a range of features that can significantly reduce power consumption during operation. Key features include: • On-the-Fly Clock Switching: The device clock can be changed under software control to the Timer1 source or the internal, low-power RC oscillator during operation, allowing users to incorporate power-saving ideas into their software designs. • Doze Mode Operation: When timing-sensitive applications, such as serial communications, require the uninterrupted operation of peripherals, the CPU clock speed can be selectively reduced, allowing incremental power savings without missing a beat. • Instruction-Based Power-Saving Modes: There are three instruction-based power-saving modes: - Idle Mode: The core is shut down while leaving the peripherals active. - Sleep Mode: The core and peripherals that require the system clock are shut down, leaving the peripherals that use their own clock, or the clock from other devices, active. - Deep Sleep Mode: The core, peripherals (except RTCC and DSWDT), Flash and SRAM are shut down. The PIC24FV32KA304 family introduces a new line of extreme low-power Microchip devices. This is a 16-bit microcontroller family with a broad peripheral feature set and enhanced computational performance. This family also offers a new migration option for those high-performance applications, which may be outgrowing their 8-bit platforms, but do not require the numerical processing power of a digital signal processor. 1.1 1.1.1 Core Features 16-BIT ARCHITECTURE Central to all PIC24F devices is the 16-bit modified Harvard architecture, first introduced with Microchip’s dsPIC® digital signal controllers. The PIC24F CPU core offers a wide range of enhancements, such as: • 16-bit data and 24-bit address paths with the ability to move information between data and memory spaces • Linear addressing of up to 12 Mbytes (program space) and 64 Kbytes (data) • A 16-element working register array with built-in software stack support • A 17 x 17 hardware multiplier with support for integer math • Hardware support for 32-bit by 16-bit division • An instruction set that supports multiple addressing modes and is optimized for high-level languages, such as C • Operational performance up to 16 MIPS 1.1.3 OSCILLATOR OPTIONS AND FEATURES The PIC24FV32KA304 family offers five different oscillator options, allowing users a range of choices in developing application hardware. These include: • Two Crystal modes using crystals or ceramic resonators. • Two External Clock modes offering the option of a divide-by-2 clock output. • Two fast internal oscillators (FRCs): One with a nominal 8 MHz output and the other with a nominal 500 kHz output. These outputs can also be divided under software control to provide clock speed as low as 31 kHz or 2 kHz. • A Phase Locked Loop (PLL) frequency multiplier, available to the External Oscillator modes and the 8 MHz FRC oscillator, which allows clock speeds of up to 32 MHz. • A separate internal RC oscillator (LPRC) with a fixed 31 kHz output, which provides a low-power option for timing-insensitive applications.  2011 Microchip Technology Inc. DS39995B-page 13 PIC24FV32KA304 FAMILY The internal oscillator block also provides a stable reference source for the Fail-Safe Clock Monitor (FSCM). This option constantly monitors the main clock source against a reference signal provided by the internal oscillator and enables the controller to switch to the internal oscillator, allowing for continued low-speed operation or a safe application shutdown. 1.3 Details on Individual Family Members Devices in the PIC24FV32KA304 family are available in 20-pin, 28-pin, 44-pin and 48-pin packages. The general block diagram for all devices is shown in Figure 1-1. The devices are different from each other in four ways: 1. Flash program memory (16 Kbytes for PIC24FV16KA devices, 32 Kbytes for PIC24FV32KA devices). Available I/O pins and ports (18 pins on two ports for 20-pin devices, 22 pins on two ports for 28-pin devices and 38 pins on three ports for 44/48-pin devices). Alternate SCL and SDA pins are available only in 28-pin, 44-pin and 48-pin devices and not in 20-pin devices. Members of the PIC24FV32KA301 family are available as both standard and high-voltage devices. High-voltage devices designated with an “FV” in the part number (such as PIC24FV32KA304), accommodate an operating VDD range of 2.0V to 5.5V, and have an on-board voltage regulator that powers the core. Peripherals operate at VDD. Standard devices, designated by “F” (such as PIC24F32KA304), function over a lower VDD range of 1.8V to 3.6V. These parts do not have an internal regulator, and both the core and peripherals operate directly from VDD. 1.1.4 EASY MIGRATION Regardless of the memory size, all the devices share the same rich set of peripherals, allowing for a smooth migration path as applications grow and evolve. The consistent pinout scheme used throughout the entire family also helps in migrating to the next larger device. This is true when moving between devices with the same pin count, or even jumping from 20-pin or 28-pin devices to 44-pin/48-pin devices. The PIC24F family is pin compatible with devices in the dsPIC33 family, and shares some compatibility with the pinout schema for PIC18 and dsPIC30. This extends the ability of applications to grow from the relatively simple, to the powerful and complex. 2. 3. 4. 1.2 Other Special Features • Communications: The PIC24FV32KA304 family incorporates a range of serial communication peripherals to handle a range of application requirements. There is an I2C™ module that supports both the Master and Slave modes of operation. It also comprises UARTs with built-in IrDA® encoders/decoders and an SPI module. • Real-Time Clock/Calendar: This module implements a full-featured clock and calendar with alarm functions in hardware, freeing up timer resources and program memory space for use of the core application. • 12-Bit A/D Converter: This module incorporates programmable acquisition time, allowing for a channel to be selected and a conversion to be initiated without waiting for a sampling period, and faster sampling speed. The 16-deep result buffer can be used either in Sleep to reduce power, or in Active mode to improve throughput. • Charge Time Measurement Unit (CTMU) Interface: The PIC24FV32KA304 family includes the new CTMU interface module, which can be used for capacitive touch sensing, proximity sensing, and also for precision time measurement and pulse generation. All other features for devices in this family are identical; these are summarized in Table 1-1. A list of the pin features available on the PIC24FV32KA304 family devices, sorted by function, is provided in Table . Note: Table 1-1 provides the pin location of individual peripheral features and not how they are multiplexed on the same pin. This information is provided in the pinout diagrams on pages 5, 5, 6, 7, 8 and 9 of the data sheet. Multiplexed features are sorted by the priority given to a feature, with the highest priority peripheral being listed first. DS39995B-page 14  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 1-1: DEVICE FEATURES FOR THE PIC24FV32KA304 FAMILY PIC24FV16KA301 PIC24FV32KA301 PIC24FV16KA302 PIC24FV32KA302 PIC24FV16KA304 PIC24FV32KA304 32K 11264 38 37 16 Features Operating Frequency Program Memory (bytes) Program Memory (instructions) Data Memory (bytes) Data EEPROM Memory (bytes) Interrupt Sources (soft vectors/ NMI traps) I/O Ports PORTA PORTB 17 16K 5632 32K 11264 DC – 32 MHz 16K 5632 2048 512 30 (26/4) PORTA PORTB 23 5 2 3 3 16 2 2 12 3 POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode, REPEAT Instruction, Hardware Traps, Configuration Word Mismatch (PWRT, OST, PLL Lock) 76 Base Instructions, Multiple Addressing Mode Variations 20-Pin PDIP/SSOP/SOIC 28-Pin SPDIP/SSOP/SOIC/QFN 44-Pin QFN/TQFP 48-Pin UQFN 13 22 PORTA PORTB PORTC 32K 11264 16K 5632 Total I/O Pins Timers: Total Number (16-bit) 32-Bit (from paired 16-bit timers) Input Capture Channels Output Compare/PWM Channels Input Change Notification Interrupt Serial Communications: UART SPI (3-wire/4-wire) I2C™ 12-Bit Analog-to-Digital Module (input channels) Analog Comparators Resets (and delays) Instruction Set Packages  2011 Microchip Technology Inc. DS39995B-page 15 PIC24FV32KA304 FAMILY TABLE 1-2: DEVICE FEATURES FOR THE PIC24F32KA304 FAMILY PIC24F16KA301 PIC24F32KA301 PIC24F16KA302 PIC24F32KA302 PIC16F16KA304 PIC24F32KA304 32K 11264 39 38 16 Features Operating Frequency Program Memory (bytes) Program Memory (instructions) Data Memory (bytes) Data EEPROM Memory (bytes) Interrupt Sources (soft vectors/ NMI traps) I/O Ports PORTA, PORTB 18 16K 5632 32K 11264 DC – 32 MHz 16K 5632 2048 512 30 (26/4) PORTA, PORTB 24 5 2 3 3 17 2 2 12 3 POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode, REPEAT Instruction, Hardware Traps, Configuration Word Mismatch (PWRT, OST, PLL Lock) 76 Base Instructions, Multiple Addressing Mode Variations 20-Pin PDIP/SSOP/SOIC 28-Pin SPDIP/SSOP/SOIC/QFN 44-Pin QFN/TQFP 48-Pin UQFN 13 23 PORTA, PORTB, PORTC 32K 11264 16K 5632 Total I/O Pins Timers: Total Number (16-bit) 32-Bit (from paired 16-bit timers) Input Capture Channels Output Compare/PWM Channels Input Change Notification Interrupt Serial Communications: UART SPI (3-wire/4-wire) I2C™ 12-Bit Analog-to-Digital Module (input channels) Analog Comparators Resets (and delays) Instruction Set Packages DS39995B-page 16  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY FIGURE 1-1: PIC24FV32KA304 FAMILY GENERAL BLOCK DIAGRAM Interrupt Controller 8 PSV and Table Data Access Control Block 16 Data Bus 16 16 Data Latch 23 PCH PCL Program Counter Repeat Stack Control Control Logic Logic Data RAM Address Latch 16 16 Read AGU Write AGU PORTA(1) RA 23 Address Latch Program Memory Data EEPROM Data Latch Address Bus 24 Inst Latch Inst Register Instruction Decode and Control Control Signals Timing OSCO/CLKO OSCI/CLKI Generation FRC/LPRC Oscillators Precision Band Gap Reference Power-up Timer Oscillator Start-up Timer Power-on Reset Watchdog Timer DSWDT BOR Literal Data PORTB(1) RB EA MUX 16 16 16 PORTC(1) RC Divide Support 17x17 Multiplier 16 x 16 W Reg Array 16-Bit ALU 16 Voltage Regulator VCAP HLVD VDD, VSS RTCC MCLR Timer2/3 Timer4/5 CTMU 12-Bit ADC Comparators Timer1 REFO IC1-3 PWM/ OC1-3 CN1-22(1) SPI1 I2C1 UART1/2 Note 1: All pins or features are not implemented on all device pinout configurations. See Table 1-3 for I/O port pin descriptions.  2011 Microchip Technology Inc. DS39995B-page 17 DS39995B-page 18  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS F Pin Number FV Pin Number 20-Pin PDIP/SSOP/ SOIC 2 3 4 5 6 — — — — 18 17 16 15 7 8 9 — — 20 19 8 7 5 4 17 5 4 8 7 11 28-Pin SPDIP/ SSOP/ SOIC 2 3 4 5 6 7 — — — 26 25 24 23 9 10 11 15 14 28 27 7 6 5 4 25 5 4 7 6 16 I/O 28-Pin QFN 27 28 1 2 3 4 — — — 23 22 21 20 6 7 8 12 11 25 24 4 3 2 1 22 2 1 4 3 13 44-Pin QFN/TQFP 19 20 21 22 23 24 25 26 27 15 14 11 10 30 31 33 42 41 17 16 24 23 22 21 14 22 21 24 23 43 48-Pin UQFN 21 22 23 24 25 26 27 28 29 16 15 12 11 33 34 36 46 45 18 17 26 25 24 23 15 24 23 26 25 47 I I I I I I I I I I I I I I I I I/O I/O I I I I I I O I I I I O ANA ANA ANA ANA ANA ANA ANA ANA ANA ANA ANA ANA ANA ANA ANA ANA I2C™ I2 C ANA ANA ANA ANA ANA ANA — ANA ANA ANA ANA — Comparator 1 Input A (+) Comparator 1 Input B (-) Comparator 1 Input C (+) Comparator 1 Input D (-) Comparator 1 Output Comparator 2 Input A (+) Comparator 2 Input B (-) Comparator 2 Input C (+) Comparator 2 Input D (-) Comparator 2 Output Alternate I2C 1 Clock Input/Output Alternate I2C 1 Data Input/Output A/D Supply Pins A/D Analog Inputs Buffer Description Function 20-Pin PDIP/SSOP/ SOIC AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 ASCL1 ASDA1 AVDD AVSS C1INA C1INB C1INC C1IND C1OUT C2INA C2INB C2INC C2IND C2OUT 2 3 4 5 6 — — — — 18 17 16 15 7 8 9 — — 20 19 8 7 5 4 17 5 4 8 7 14 20-Pin QFN 19 20 1 2 3 — — — — 15 14 13 12 4 5 6 — — 17 16 5 4 2 1 14 2 1 5 4 11 28-Pin SPDIP/SSOP/ SOIC 2 3 4 5 6 7 — — — 26 25 24 23 9 10 11 15 14 28 27 7 6 5 4 25 5 4 7 6 20 28-Pin QFN 27 28 1 2 3 4 — — — 23 22 21 20 6 7 8 12 11 25 24 4 3 2 1 22 2 1 4 3 17 44-Pin QFN/TQFP 19 20 21 22 23 24 25 26 27 15 14 11 10 30 31 33 42 41 17 16 24 23 22 21 14 22 21 24 23 7 48-Pin UQFN 21 22 23 24 25 26 27 28 29 16 15 12 11 33 34 36 46 45 18 17 26 25 24 23 15 24 23 26 25 7 20-Pin QFN 19 20 1 2 3 — — — — 15 14 13 12 4 5 6 — — 17 16 5 4 2 1 14 2 1 5 4 8 TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) F Pin Number FV Pin Number 20-Pin PDIP/SSOP/ SOIC 18 17 2 4 12 7 8 10 9 2 3 4 5 6 ––––18 17 16 15 –––28-Pin SPDIP/ SSOP/ SOIC 26 25 2 4 17 9 10 12 11 2 3 4 5 6 7 –19 –26 25 24 23 22 21 — I/O 28-Pin QFN 23 22 27 1 14 6 7 9 8 27 28 1 2 3 4 –16 –23 22 21 20 19 18 — 44-Pin QFN/TQFP 15 14 19 21 44 30 31 34 33 19 20 21 22 23 24 — 6 27 15 14 11 10 9 8 3 48-Pin UQFN 16 15 21 23 48 33 34 37 36 21 22 23 24 25 26 –6 29 16 15 12 11 10 9 3 I I I I O I O I I I I I I I I I I I I I I I I I I ANA ANA ANA ANA — ANA — ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST Comparator 3 Input A (+) Comparator 3 Input B (-) Comparator 3 Input C (+) Comparator 3 Input D (-) Comparator 3 Output Main Clock Input System Clock Output Interrupt-on-Change Inputs Buffer Description  2011 Microchip Technology Inc. DS39995B-page 19 Function 20-Pin PDIP/SSOP/ SOIC C3INA C3INB C3INC C3IND C3OUT CLK I CLKO CN0 CN1 CN2 CN3 CN4 CN5 CN6 CN7 CN8 CN9 CN10 CN11 CN12 CN13 CN14 CN15 CN16 CN17 18 17 2 4 12 7 8 10 9 2 3 4 5 6 — 14 ––18 17 16 15 –––20-Pin QFN 15 14 19 1 9 4 5 7 6 19 20 1 2 3 — 11 ––15 14 13 12 –––28-Pin SPDIP/SSOP/ SOIC 26 25 2 4 17 9 10 12 11 2 3 4 5 6 7 20 19 — 26 25 24 23 22 21 — 28-Pin QFN 23 22 27 1 14 6 7 9 8 27 28 1 2 3 4 17 16 — 23 22 21 20 19 18 — 44-Pin QFN/TQFP 15 14 19 21 44 30 31 34 33 19 20 21 22 23 24 7 6 27 15 14 11 10 9 8 3 48-Pin UQFN 16 15 21 23 48 33 34 37 36 21 22 23 24 25 26 7 6 29 16 15 12 11 10 9 3 20-Pin QFN 15 14 19 1 9 4 5 7 6 19 20 1 2 3 — — — — 15 14 13 12 — — — PIC24FV32KA304 FAMILY TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) F Pin Number FV Pin Number 20-Pin PDIP/SSOP/ SOIC — — — 13 12 11 –––––8 7 — — — — — — 17 2 3 4 11 28-Pin SPDIP/ SSOP/ SOIC — — –18 17 16 15 ––14 –10 9 — — — — — — 25 2 3 4 2 I/O 28-Pin QFN — ––15 14 13 12 ––11 –7 6 — — — — — — 22 27 28 1 27 44-Pin QFN/TQFP 2 5 4 1 44 43 42 37 38 41 36 31 30 26 25 32 35 12 13 14 19 20 21 19 48-Pin UQFN 2 5 4 1 48 47 46 40 41 45 39 34 33 28 27 35 38 13 14 15 21 22 23 21 I I I I I I I I I I I I I I I I I I I I I I I I ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ANA ANA ANA ANA ST Comparator Voltage Reference Output Comparator Reference Positive Input Voltage Comparator Reference Negative Input Voltage CTMU Comparator Input Buffer Description DS39995B-page 20  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Function 20-Pin PDIP/SSOP/ SOIC CN18 CN19 CN20 CN21 CN22 CN23 CN24 CN25 CN26 CN27 CN28 CN29 CN30 CN31 CN32 CN33 CN34 CN35 CN36 CVREF CVREF+ CVREFCTCMP CTED1 — ––13 12 11 –––––8 7 ––––––17 2 3 4 11 20-Pin QFN — ––10 9 8 –––––5 4 ––––––14 19 20 1 11 28-Pin SPDIP/SSOP/ SOIC — — — 18 17 16 15 — — 14 — 10 9 — — — — — — 25 2 3 4 20 28-Pin QFN — — — 15 14 13 12 — — 11 — 7 6 — — — — — — 22 27 28 1 17 44-Pin QFN/TQFP 2 5 4 1 44 43 42 37 38 41 36 31 30 26 25 32 35 12 13 14 19 20 21 7 48-Pin UQFN 2 5 4 1 48 47 46 40 41 45 39 34 33 28 27 35 38 13 14 15 21 22 23 7 20-Pin QFN — — — 10 9 8 — — — — — 5 4 — — — — — — 14 19 20 1 8 TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) F Pin Number FV Pin Number 20-Pin PDIP/SSOP/ SOIC 12 — 5 6 15 — 13 17 18 — — — 16 15 11 13 15 11 17 15 1 11 4 5 17 16 7 8 5 4 2 28-Pin SPDIP/ SSOP/ SOIC 17 21 5 6 23 19 18 25 26 — — 22 24 23 19 18 23 16 25 23 1 16 22 21,5 25 24 9 10 5 4 22,2 I/O 28-Pin QFN 14 18 2 3 20 16 15 22 23 — — 19 21 20 16 15 20 13 22 20 26 13 19 18,2 22 21 6 7 2 1 19,27 44-Pin QFN/TQFP 44 8 22 23 10 6 1 14 15 5 13 9 11 10 6 5 13 43 14 10 18 43 4 8,12,22 14 11,32 30 31 22 21 9,19 48-Pin UQFN 48 9 24 25 11 6 1 15 16 5 14 10 12 11 6 5 14 47 15 11 19 47 4 9,13,24 15 12,35 33 34 24 23 10,21 I I I I I I I I I I I I O I I I I I I I I O O O O O I O I/O I/O I/O ST ST ST ST ST ST ST ST ST ST ST ST — ST ST ST ST ST ST ST ST — — — — — ANA ANA ST ST ST High/Low-Voltage Detect Input Input Capture 1 Input Input Capture 2 Input Input Capture 3 Input Interrupt 0 Input Interrupt 1 Input Interrupt 2 Input Output Compare/PWM1 Output Output Compare/PWM2 Output Output Compare/PWM3 Output Output Compare Fault A Output Compare Fault B Main Oscillator Input Main Oscillator Output ICSP™ Clock 1 ICSP Data 1 ICSP Clock 2 CTMU Pulse Output CTMU Trigger Edge Inputs Buffer Description  2011 Microchip Technology Inc. DS39995B-page 21 Function 20-Pin PDIP/SSOP/ SOIC CTED2 CTED3 CTED4 CTED5 CTED6 CTED7 CTED8 CTED9 CTED10 CTED11 CTED12 CTED13 CTPLS HLVDIN IC1 IC2 IC3 INT0 INT1 INT2 MCLR OC1 OC2 OC3 OCFA OFCB OSCI OSCO PGEC1 PCED1 PGEC2 12 — 5 6 15 — 13 17 18 — — — 16 15 11 13 15 11 17 14 1 11 4 5 17 16 7 8 5 4 2 20-Pin QFN 9 — 2 3 12 — 10 14 15 — — — 13 12 11 10 12 8 14 11 18 11 1 2 14 13 4 5 2 1 19 28-Pin SPDIP/SSOP/ SOIC 17 21 5 6 23 19 18 25 26 — — 22 24 23 19 18 23 16 25 20 1 20 22 21,5 25 24 9 10 5 4 22,2 28-Pin QFN 14 18 2 3 20 16 15 22 23 — — 19 21 20 16 15 20 13 22 17 26 17 19 18,2 22 21 6 7 2 1 19,27 44-Pin QFN/TQFP 44 8 22 23 10 6 1 14 15 5 13 9 11 10 6 5 13 43 14 7 18 7 4 8,12,22 14 11,32 30 31 22 21 9,19 48-Pin UQFN 48 9 24 25 11 6 1 15 16 5 14 10 12 11 6 5 14 47 15 7 19 7 4 9,13,24 15 12,35 33 34 24 23 10,21 20-Pin QFN 9 — 2 3 12 — 10 14 15 — — — 13 12 8 10 12 8 14 12 18 8 1 2 14 13 4 5 2 1 19 PIC24FV32KA304 FAMILY TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) F Pin Number FV Pin Number 20-Pin PDIP/SSOP/ SOIC 3 10 9 2 3 7 8 10 1 — — — — — — 4 5 6 — 9 — — 11 12 13 — — 15 16 17 18 28-Pin SPDIP/ SSOP/ SOIC 21,3 12,15 11,14 2 3 9 10 12 1 — 19 — — — — 4 5 6 7 11 14 15 16 17 18 21 22 23 24 25 26 I/O 28-Pin QFN 18,28 9,12 8,11 27 28 6 7 9 26 — 16 — — — — 1 2 3 4 8 11 12 13 14 15 18 19 20 21 22 23 44-Pin QFN/TQFP 8,20 34,42 33,41 19 20 30 31 34 18 — 6 32 35 12 13 21 22 23 24 33 41 42 43 44 1 8 9 10 11 14 15 48-Pin UQFN 9,22 37,46 36,45 21 22 33 34 37 19 — 6 35 38 13 14 23 24 25 26 36 45 46 47 48 1 9 10 11 12 15 16 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST PORTB Pins ICSP Data 2 ICSP Clock 3 ICSP Data 3 PORTA Pins Buffer Description DS39995B-page 22  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Function 20-Pin PDIP/SSOP/ SOIC PGED2 PGEC3 PGED3 RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 RA8 RA9 RA10 RA11 RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 RB8 RB9 RB10 RB11 RB12 RB13 RB14 RB15 3 10 9 2 3 7 8 10 1 14 — — — — — 4 5 6 — 9 — — 11 12 13 — — 15 16 17 18 20-Pin QFN 20 7 6 19 20 4 5 7 18 11 — — — — — 1 2 3 — 6 — — 8 9 10 — — 12 13 14 15 28-Pin SPDIP/SSOP/ SOIC 21,3 12,15 11,14 2 3 9 10 12 1 20 19 — — — — 4 5 6 7 11 14 15 16 17 18 21 22 23 24 25 26 28-Pin QFN 18,28 9,12 8,11 27 28 6 7 9 26 17 16 — — — — 1 2 3 4 8 11 12 13 14 15 18 19 20 21 22 23 44-Pin QFN/TQFP 8,20 34,42 33,41 19 20 30 31 34 18 7 6 32 35 12 13 21 22 23 24 33 41 42 43 44 1 8 9 10 11 14 15 48-Pin UQFN 9,22 37,46 36,45 21 22 33 34 37 19 7 6 35 38 13 14 23 24 25 26 36 45 46 47 48 1 9 10 11 12 15 16 20-Pin QFN 20 7 6 19 20 4 5 7 18 — — — — — — 1 2 3 — 6 — — 8 9 10 — — 12 13 14 15 TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) F Pin Number FV Pin Number 20-Pin PDIP/SSOP/ SOIC — — — — — — — — — — 18 17 15 2 12 18 10 13 6 17 4 16 3 9 10 18 15 13 18 18 6 28-Pin SPDIP/ SSOP/ SOIC — — — — — — — — — — 26 25 22,23 2,14 17 26,7 12 18 6 21,25 19,4 24 3,15 11 12 26 23 18 26 26 6 I/O 28-Pin QFN — — — — — — — — — — 23 22 19,20 27,11 14 23,4 9 15 3 18,22 16,1 21 28,12 8 9 23 20 15 23 23 3 44-Pin QFN/TQFP 25 26 27 36 37 38 2 3 4 5 15 14 9,10 19,38,41 44 15,24 34 1 23 8,14 6,21,36 11 20,37,42 33 34 15 10,35 1 15 15 23 48-Pin UQFN 27 28 29 39 40 41 2 3 4 5 16 15 10,11 21,41,45 48 16,26 37 1 25 9,15 6,23,39 12 22,40,46 36 37 16 11,38 1 16 16 25 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O I/O I/O I/O I/O I I/O I/O I I O O I O O O I I I I ST ST ST ST ST ST ST ST ST ST — — ST ST I2 C I2 C ST I2 C I2C ST ST — — ANA ANA — — ST ST ST ST Reference Clock Output Real-Time Clock/Calendar Output SPI1 Serial Input/Output Clock SPI2 Serial Input/Output Clock I2C1 Clock Input/Output I2C2 Clock Input/Output Digital Secondary Clock Input I2C1 Data Input/Output I2C2 Data Input/Output SPI1 Serial Data Input SPI2 Serial Data Input SPI1 Serial Data Output SPI2 Serial Data Output Secondary Oscillator Input Secondary Oscillator Output SPI1 Slave Select SPI2 Slave Select Timer1 Clock Timer2 Clock Timer3 Clock Timer4 Clock PORTC Pins Buffer Description  2011 Microchip Technology Inc. DS39995B-page 23 Function 20-Pin PDIP/SSOP/ SOIC RC0 RC1 RC2 RC3 RC4 RC5 RC6 RC7 RC8 RC9 REFO RTCC SCK1 SCK2 SCL1 SCL2 SCLKI SDA1 SDA2 SDI1 SDI2 SDO1 SDO2 SOSCI SOSCO SS1 SS2 T1CK T2CK T3CK T4CK — — — — — — — — — — 18 17 15 2 12 18 10 13 6 17 4 16 3 9 10 18 15 13 18 18 6 20-Pin QFN — — — — — — — — — — 15 14 12 19 9 15 7 10 3 14 1 13 20 6 7 15 12 10 15 15 3 28-Pin SPDIP/SSOP/ SOIC — — — — — — — — — — 26 25 22,23 2,14 17 26,7 12 18 6 21,25 19,4 24 3,15 11 12 26 23 18 26 26 6 28-Pin QFN — — — — — — — — — — 23 22 19,20 27,11 14 23,4 9 15 3 18,22 16,1 21 28,12 8 9 23 20 15 23 23 3 44-Pin QFN/TQFP 25 26 27 36 37 38 2 3 4 5 15 14 9,10 19,38,41 44 15,24 34 1 23 8,14 6,21,36 11 20,37,42 33 34 15 10,35 1 15 15 23 48-Pin UQFN 27 28 29 39 40 41 2 3 4 5 16 15 10,11 21,41,45 48 16,26 37 1 25 9,15 6,23,39 12 22,40,46 36 37 16 11,38 1 16 16 25 20-Pin QFN — — — — — — — — — — 15 14 12 19 9 15 7 10 3 14 1 13 20 6 7 15 12 10 15 15 3 PIC24FV32KA304 FAMILY TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) F Pin Number FV Pin Number 20-Pin PDIP/SSOP/ SOIC 6 12 13 6 11 10 9 5 4 4 14 20 2 3 19 28-Pin SPDIP/ SSOP/ SOIC 6 17 18 6 16 12 11 5 4 4 20 28,13 2 3 27,8 I/O 28-Pin QFN 3 14 15 3 13 9 8 2 1 1 17 25,10 27 28 24,5 44-Pin QFN/TQFP 23 44 1 2,23 3,43 34 33 22 21 21 7 17,28,40 19 20 16,29,39 48-Pin UQFN 25 48 1 2,25 3,47 37 36 24 23 23 7 18,30,43 21 22 17,31,42 I I O I O I O I O I P P I I P ST ST — ST — ST — ST — ANA — — ANA ANA — A/D Reference Voltage Input (+) A/D Reference Voltage Input (-) Timer5 Clock UART1 Clear to Send Input UART1 Request to Send Output UART1 Receive UART1 Transmit UART2 Clear to Send Input UART2 Request to Send Output UART2 Receive UART2 Transmit Ultra Low-Power Wake-up Input Core Power Buffer Description DS39995B-page 24  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Function 20-Pin PDIP/SSOP/ SOIC T5CK U1CTS U1RTS U1RX U1TX U2CTS U2RTS U2RX U2TX ULPWU VCAP VDD VREF+ VREFVSS 6 12 13 6 11 10 9 5 4 4 — 20 2 3 19 20-Pin QFN 3 9 10 3 8 7 6 2 1 1 — 17 19 20 16 28-Pin SPDIP/SSOP/ SOIC 6 17 18 6 16 12 11 5 4 4 — 28,13 2 3 27,8 28-Pin QFN 3 14 15 3 13 9 8 2 1 1 — 25,10 27 28 24,5 44-Pin QFN/TQFP 23 44 1 2,23 3,43 34 33 22 21 21 — 17,28,40 19 20 16,29,39 48-Pin UQFN 25 48 1 2,25 3,47 37 36 24 23 23 — 18,30,43 21 22 17,31,42 20-Pin QFN 3 9 10 3 8 7 6 2 1 1 11 17 19 20 16 PIC24FV32KA304 FAMILY 2.0 GUIDELINES FOR GETTING STARTED WITH 16-BIT MICROCONTROLLERS Basic Connection Requirements FIGURE 2-1: RECOMMENDED MINIMUM CONNECTIONS C2(2) 2.1 VDD VDD MCLR VCAP Getting started with the PIC24FV32KA304 family family of 16-bit microcontrollers requires attention to a minimal set of device pin connections before proceeding with development. The following pins must always be connected: • All VDD and VSS pins (see Section 2.2 “Power Supply Pins”) • All AVDD and AVSS pins, regardless of whether or not the analog device features are used (see Section 2.2 “Power Supply Pins”) • MCLR pin (see Section 2.3 “Master Clear (MCLR) Pin”) • VCAP pins (see Section 2.4 “Voltage Regulator Pin (VCAP)”) These pins must also be connected if they are being used in the end application: • PGECx/PGEDx pins used for In-Circuit Serial Programming™ (ICSP™) and debugging purposes (see Section 2.5 “ICSP Pins”) • OSCI and OSCO pins when an external oscillator source is used (see Section 2.6 “External Oscillator Pins”) Additionally, the following pins may be required: • VREF+/VREF- pins are used when external voltage reference for analog modules is implemented Note: The AVDD and AVSS pins must always be connected, regardless of whether any of the analog modules are being used. R1 R2 VSS (1) C1 (3) PIC24FXXKXX VSS VDD C7 C6(2) AVDD VDD VSS AVSS VDD VSS C3(2) C5(2) C4(2) Key (all values are recommendations): C1 through C6: 0.1 F, 20V ceramic C7: 10 F, 16V tantalum or ceramic R1: 10 kΩ R2: 100Ω to 470Ω Note 1: See Section 2.4 “Voltage Regulator Pin (VCAP)” for explanation of VCAP pin connections. The example shown is for a PIC24F device with five VDD/VSS and AVDD/AVSS pairs. Other devices may have more or less pairs; adjust the number of decoupling capacitors appropriately. Some PIC24F K parts do not have a regulator. 2: 3: The minimum mandatory connections are shown in Figure 2-1.  2011 Microchip Technology Inc. DS39995B-page 25 PIC24FV32KA304 FAMILY 2.2 2.2.1 Power Supply Pins DECOUPLING CAPACITORS 2.3 Master Clear (MCLR) Pin The use of decoupling capacitors on every pair of power supply pins, such as VDD, VSS, AVDD and AVSS, is required. Consider the following criteria when using decoupling capacitors: • Value and type of capacitor: A 0.1 F (100 nF), 10-20V capacitor is recommended. The capacitor should be a low-ESR device, with a resonance frequency in the range of 200 MHz and higher. Ceramic capacitors are recommended. • Placement on the printed circuit board: The decoupling capacitors should be placed as close to the pins as possible. It is recommended to place the capacitors on the same side of the board as the device. If space is constricted, the capacitor can be placed on another layer on the PCB using a via; however, ensure that the trace length from the pin to the capacitor is no greater than 0.25 inch (6 mm). • Handling high-frequency noise: If the board is experiencing high-frequency noise (upward of tens of MHz), add a second ceramic type capacitor in parallel to the above described decoupling capacitor. The value of the second capacitor can be in the range of 0.01 F to 0.001 F. Place this second capacitor next to each primary decoupling capacitor. In high-speed circuit designs, consider implementing a decade pair of capacitances as close to the power and ground pins as possible (e.g., 0.1 F in parallel with 0.001 F). • Maximizing performance: On the board layout from the power supply circuit, run the power and return traces to the decoupling capacitors first, and then to the device pins. This ensures that the decoupling capacitors are first in the power chain. Equally important is to keep the trace length between the capacitor and the power pins to a minimum, thereby reducing PCB trace inductance. The MCLR pin provides two specific device functions: Device Reset, and Device Programming and Debugging. If programming and debugging are not required in the end application, a direct connection to VDD may be all that is required. The addition of other components, to help increase the application’s resistance to spurious Resets from voltage sags, may be beneficial. A typical configuration is shown in Figure 2-1. Other circuit designs may be implemented, depending on the application’s requirements. During programming and debugging, the resistance and capacitance that can be added to the pin must be considered. Device programmers and debuggers drive the MCLR pin. Consequently, specific voltage levels (VIH and VIL) and fast signal transitions must not be adversely affected. Therefore, specific values of R1 and C1 will need to be adjusted based on the application and PCB requirements. For example, it is recommended that the capacitor, C1, be isolated from the MCLR pin during programming and debugging operations by using a jumper (Figure 2-2). The jumper is replaced for normal run-time operations. Any components associated with the MCLR pin should be placed within 0.25 inch (6 mm) of the pin. FIGURE 2-2: VDD R1 EXAMPLE OF MCLR PIN CONNECTIONS R2 JP C1 MCLR PIC24FXXKXX 2.2.2 TANK CAPACITORS Note 1: On boards with power traces running longer than six inches in length, it is suggested to use a tank capacitor for integrated circuits, including microcontrollers, to supply a local power source. The value of the tank capacitor should be determined based on the trace resistance that connects the power supply source to the device, and the maximum current drawn by the device in the application. In other words, select the tank capacitor so that it meets the acceptable voltage sag at the device. Typical values range from 4.7 F to 47 F. R1  10 k is recommended. A suggested starting value is 10 k. Ensure that the MCLR pin VIH and VIL specifications are met. R2  470 will limit any current flowing into MCLR from the external capacitor, C, in the event of MCLR pin breakdown, due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Ensure that the MCLR pin VIH and VIL specifications are met. 2: DS39995B-page 26  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 2.4 Note: Voltage Regulator Pin (VCAP) This section applies only to PIC24F K devices with an on-chip voltage regulator. Refer to Section 29.0 “Electrical Characteristics” for information on VDD and VDDCORE. FIGURE 2-3: Some of the PIC24F K devices have an internal voltage regulator. These devices have the voltage regulator output brought out on the VCAP pin. On the PIC24F K devices with regulators, a low-ESR (< 5Ω) capacitor is required on the VCAP pin to stabilize the voltage regulator output. The VCAP pin must not be connected to VDD and must use a capacitor of 10 µF connected to ground. The type can be ceramic or tantalum. Suitable examples of capacitors are shown in Table 2-1. Capacitors with equivalent specifications can be used. Designers may use Figure 2-3 to evaluate ESR equivalence of candidate devices. The placement of this capacitor should be close to VCAP. It is recommended that the trace length not exceed 0.25 inch (6 mm). Refer to Section 29.0 “Electrical Characteristics” for additional information. FREQUENCY vs. ESR PERFORMANCE FOR SUGGESTED VCAP 10 1 ESR () 0.1 0.01 0.001 0.01 0.1 1 10 100 Frequency (MHz) 1000 10,000 Note: Typical data measurement at 25°C, 0V DC bias. TABLE 2-1: Make TDK TDK Panasonic Panasonic Murata Murata SUITABLE CAPACITOR EQUIVALENTS Part # C3216X7R1C106K C3216X5R1C106K ECJ-3YX1C106K ECJ-4YB1C106K GRM32DR71C106KA01L GRM31CR61C106KC31L Nominal Capacitance 10 µF 10 µF 10 µF 10 µF 10 µF 10 µF Base Tolerance ±10% ±10% ±10% ±10% ±10% ±10% Rated Voltage 16V 16V 16V 16V 16V 16V Temp. Range -55 to 125ºC -55 to 85ºC -55 to 125ºC -55 to 85ºC -55 to 125ºC -55 to 85ºC  2011 Microchip Technology Inc. DS39995B-page 27 PIC24FV32KA304 FAMILY 2.4.1 CONSIDERATIONS FOR CERAMIC CAPACITORS FIGURE 2-4: In recent years, large value, low-voltage, surface-mount ceramic capacitors have become very cost effective in sizes up to a few tens of microfarad. The low-ESR, small physical size and other properties make ceramic capacitors very attractive in many types of applications. Ceramic capacitors are suitable for use with the internal voltage regulator of this microcontroller. However, some care is needed in selecting the capacitor to ensure that it maintains sufficient capacitance over the intended operating range of the application. Typical low-cost, 10 F ceramic capacitors are available in X5R, X7R and Y5V dielectric ratings (other types are also available, but are less common). The initial tolerance specifications for these types of capacitors are often specified as ±10% to ±20% (X5R and X7R), or -20%/+80% (Y5V). However, the effective capacitance that these capacitors provide in an application circuit will also vary based on additional factors, such as the applied DC bias voltage and the temperature. The total in-circuit tolerance is, therefore, much wider than the initial tolerance specification. The X5R and X7R capacitors typically exhibit satisfactory temperature stability (ex: ±15% over a wide temperature range, but consult the manufacturer’s data sheets for exact specifications). However, Y5V capacitors typically have extreme temperature tolerance specifications of +22%/-82%. Due to the extreme temperature tolerance, a 10 F nominal rated Y5V type capacitor may not deliver enough total capacitance to meet minimum internal voltage regulator stability and transient response requirements. Therefore, Y5V capacitors are not recommended for use with the internal regulator if the application must operate over a wide temperature range. In addition to temperature tolerance, the effective capacitance of large value ceramic capacitors can vary substantially, based on the amount of DC voltage applied to the capacitor. This effect can be very significant, but is often overlooked or is not always documented. A typical DC bias voltage vs. capacitance graph for X7R type capacitors is shown in Figure 2-4. DC BIAS VOLTAGE vs. CAPACITANCE CHARACTERISTICS Capacitance Change (%) 10 0 -10 -20 -30 -40 -50 -60 -70 -80 0 16V Capacitor 10V Capacitor 6.3V Capacitor 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 DC Bias Voltage (VDC) When selecting a ceramic capacitor to be used with the internal voltage regulator, it is suggested to select a high-voltage rating, so that the operating voltage is a small percentage of the maximum rated capacitor voltage. For example, choose a ceramic capacitor rated at 16V for the 3.3V or 2.5V core voltage. Suggested capacitors are shown in Table 2-1. 2.5 ICSP Pins The PGC and PGD pins are used for In-Circuit Serial Programming™ (ICSP™) and debugging purposes. It is recommended to keep the trace length between the ICSP connector and the ICSP pins on the device as short as possible. If the ICSP connector is expected to experience an ESD event, a series resistor is recommended, with the value in the range of a few tens of ohms, not to exceed 100Ω. Pull-up resistors, series diodes and capacitors on the PGC and PGD pins are not recommended as they will interfere with the programmer/debugger communications to the device. If such discrete components are an application requirement, they should be removed from the circuit during programming and debugging. Alternatively, refer to the AC/DC characteristics and timing requirements information in the respective device Flash programming specification for information on capacitive loading limits, and pin input voltage high (VIH) and input low (VIL) requirements. For device emulation, ensure that the “Communication Channel Select” (i.e., PGCx/PGDx pins), programmed into the device, matches the physical connections for the ICSP to the Microchip debugger/emulator tool. For more information on available Microchip development tools connection requirements, refer to Section 27.0 “Development Support”. DS39995B-page 28  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 2.6 External Oscillator Pins FIGURE 2-5: Many microcontrollers have options for at least two oscillators: a high-frequency primary oscillator and a low-frequency secondary oscillator (refer to for Section 9.0 “Oscillator Configuration”details). The oscillator circuit should be placed on the same side of the board as the device. Place the oscillator circuit close to the respective oscillator pins with no more than 0.5 inch (12 mm) between the circuit components and the pins. The load capacitors should be placed next to the oscillator itself, on the same side of the board. Use a grounded copper pour around the oscillator circuit to isolate it from surrounding circuits. The grounded copper pour should be routed directly to the MCU ground. Do not run any signal traces or power traces inside the ground pour. Also, if using a two-sided board, avoid any traces on the other side of the board where the crystal is placed. Layout suggestions are shown in Figure 2-5. In-line packages may be handled with a single-sided layout that completely encompasses the oscillator pins. With fine-pitch packages, it is not always possible to completely surround the pins and components. A suitable solution is to tie the broken guard sections to a mirrored ground layer. In all cases, the guard trace(s) must be returned to ground. In planning the application’s routing and I/O assignments, ensure that adjacent port pins and other signals, in close proximity to the oscillator, are benign (i.e., free of high frequencies, short rise and fall times, and other similar noise). For additional information and design guidance on oscillator circuits, please refer to these Microchip Application Notes, available at the corporate web site (www.microchip.com): • AN826, “Crystal Oscillator Basics and Crystal Selection for rfPIC™ and PICmicro® Devices” • AN849, “Basic PICmicro® Oscillator Design” • AN943, “Practical PICmicro® Oscillator Analysis and Design” • AN949, “Making Your Oscillator Work” SUGGESTED PLACEMENT OF THE OSCILLATOR CIRCUIT Single-Sided and In-Line Layouts: Copper Pour (tied to ground) Primary Oscillator Crystal DEVICE PINS Primary Oscillator C1 C2 ` OSC1 OSC2 GND ` T1OSO Timer1 Oscillator Crystal T1OS I ` T1 Oscillator: C1 T1 Oscillator: C2 Fine-Pitch (Dual-Sided) Layouts: Top Layer Copper Pour (tied to ground) Bottom Layer Copper Pour (tied to ground) OSCO C2 GND Oscillator Crystal C1 OSCI 2.7 Unused I/Os DEVICE PINS Unused I/O pins should be configured as outputs and driven to a logic low state. Alternatively, connect a 1 kΩ to 10 kΩ resistor to VSS on unused pins and drive the output to logic low.  2011 Microchip Technology Inc. DS39995B-page 29 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 30  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 3.0 Note: CPU This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the CPU, refer to the “PIC24F Family Reference Manual”, Section 2. “CPU” (DS39703). For most instructions, the core is capable of executing a data (or program data) memory read, a working register (data) read, a data memory write and a program (instruction) memory read per instruction cycle. As a result, three parameter instructions can be supported, allowing trinary operations (i.e., A + B = C) to be executed in a single cycle. A high-speed, 17-bit by 17-bit multiplier has been included to significantly enhance the core arithmetic capability and throughput. The multiplier supports Signed, Unsigned and Mixed mode, 16-bit by 16-bit or 8-bit by 8-bit integer multiplication. All multiply instructions execute in a single cycle. The 16-bit ALU has been enhanced with integer divide assist hardware that supports an iterative non-restoring divide algorithm. It operates in conjunction with the REPEAT instruction looping mechanism and a selection of iterative divide instructions to support 32-bit (or 16-bit), divided by 16-bit integer signed and unsigned division. All divide operations require 19 cycles to complete but are interruptible at any cycle boundary. The PIC24F has a vectored exception scheme with up to eight sources of non-maskable traps and up to 118 interrupt sources. Each interrupt source can be assigned to one of seven priority levels. A block diagram of the CPU is illustrated in Figure 3-1. The PIC24F CPU has a 16-bit (data) modified Harvard architecture with an enhanced instruction set and a 24-bit instruction word with a variable length opcode field. The Program Counter (PC) is 23 bits wide and addresses up to 4M instructions of user program memory space. A single-cycle instruction prefetch mechanism is used to help maintain throughput and provides predictable execution. All instructions execute in a single cycle, with the exception of instructions that change the program flow, the double-word move (MOV.D) instruction and the table instructions. Overhead-free program loop constructs are supported using the REPEAT instructions, which are interruptible at any point. PIC24F devices have sixteen, 16-bit working registers in the programmer’s model. Each of the working registers can act as a data, address or address offset register. The 16th working register (W15) operates as a Software Stack Pointer (SSP) for interrupts and calls. The upper 32 Kbytes of the data space memory map can optionally be mapped into program space at any 16K word boundary of either program memory or data EEPROM memory, defined by the 8-bit Program Space Visibility Page Address (PSVPAG) register. The program to data space mapping feature lets any instruction access program space as if it were data space. The Instruction Set Architecture (ISA) has been significantly enhanced beyond that of the PIC18, but maintains an acceptable level of backward compatibility. All PIC18 instructions and addressing modes are supported, either directly, or through simple macros. Many of the ISA enhancements have been driven by compiler efficiency needs. The core supports Inherent (no operand), Relative, Literal, Memory Direct and three groups of addressing modes. All modes support Register Direct and various Register Indirect modes. Each group offers up to seven addressing modes. Instructions are associated with predefined addressing modes depending upon their functional requirements. 3.1 Programmer’s Model Figure 3-2 displays the programmer’s model for the PIC24F. All registers in the programmer’s model are memory mapped and can be manipulated directly by instructions. Table 3-1 provides a description of each register. All registers associated with the programmer’s model are memory mapped.  2011 Microchip Technology Inc. DS39995B-page 31 PIC24FV32KA304 FAMILY FIGURE 3-1: PSV and Table Data Access Control Block Interrupt Controller 8 23 23 PCH PCL Program Counter Loop Stack Control Control Logic Logic Data RAM Address Latch 16 RAGU WAGU 16 Data Bus 16 16 Data Latch 16 PIC24F CPU CORE BLOCK DIAGRAM 23 Address Latch Program Memory Data EEPROM Data Latch 24 Address Bus ROM Latch EA MUX 16 16 Instruction Reg Control Signals to Various Blocks Hardware Multiplier Divide Support 16 x 16 W Register Array 16 Literal Data 16-Bit ALU 16 Instruction Decode and Control To Peripheral Modules TABLE 3-1: W0 through W15 PC SR SPLIM TBLPAG PSVPAG RCOUNT CORCON CPU CORE REGISTERS Description Working Register Array 23-Bit Program Counter ALU STATUS Register Stack Pointer Limit Value Register Table Memory Page Address Register Program Space Visibility Page Address Register Repeat Loop Counter Register CPU Control Register Register(s) Name DS39995B-page 32  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY FIGURE 3-2: PROGRAMMER’S MODEL 15 Divider Working Registers W0 (WREG) W1 W2 W3 W4 W5 W6 W7 W8 W9 W10 W11 W12 W13 W14 W15 Frame Pointer Stack Pointer 0 Stack Pointer Limit Value Register Program Counter Table Memory Page Address Register Program Space Visibility Page Address Register Repeat Loop Counter Register Working/Address Registers 0 Multiplier Registers SPLIM 22 PC 7 TBLPAG 7 PSVPAG 15 RCOUNT 15 SRH SRL 0 0 0 0 0 0 0 ALU STATUS Register (SR) — — — — — — — DC IPL RA N OV Z C 210 15 0 CPU Control Register (CORCON) — — — — — — — — — — — — IPL3 PSV — — Registers or bits are shadowed for PUSH.S and POP.S instructions.  2011 Microchip Technology Inc. DS39995B-page 33 PIC24FV32KA304 FAMILY 3.2 CPU Control Registers SR: ALU STATUS REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0, HSC DC bit 8 R/W-0, HSC(1) R/W-0, HSC(1) IPL1 (2) REGISTER 3-1: U-0 — bit 15 R/W-0, HSC(1) IPL2 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-9 bit 8 (2) R-0, HSC RA R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0, HSC N OV Z C bit 0 IPL0 (2) HSC = Hardware Settable/Clearable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown Unimplemented: Read as ‘0’ DC: ALU Half Carry/Borrow bit 1 = A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred 0 = No carry-out from the 4th or 8th low-order bit of the result has occurred IPL: CPU Interrupt Priority Level Status bits(1,2) 111 = CPU interrupt priority level is 7 (15); user interrupts disabled 110 = CPU interrupt priority level is 6 (14) 101 = CPU Interrupt priority Level is 5 (13) 100 = CPU interrupt priority level is 4 (12) 011 = CPU interrupt priority level is 3 (11) 010 = CPU interrupt priority level is 2 (10) 001 = CPU interrupt priority level is 1 (9) 000 = CPU interrupt priority level is 0 (8) RA: REPEAT Loop Active bit 1 = REPEAT loop in progress 0 = REPEAT loop not in progress N: ALU Negative bit 1 = Result was negative 0 = Result was non-negative (zero or positive) OV: ALU Overflow bit 1 = Overflow occurred for signed (2’s complement) arithmetic in this arithmetic operation 0 = No overflow has occurred Z: ALU Zero bit 1 = An operation, which effects the Z bit, has set it at some time in the past 0 = The most recent operation, which effects the Z bit, has cleared it (i.e., a non-zero result) C: ALU Carry/Borrow bit 1 = A carry-out from the Most Significant bit (MSb) of the result occurred 0 = No carry-out from the Most Significant bit (MSb) of the result occurred The IPL Status bits are read-only when NSTDIS (INTCON1) = 1. The IPL Status bits are concatenated with the IPL3 bit (CORCON) to form the CPU Interrupt Priority Level (IPL). The value in parentheses indicates the IPL when IPL3 = 1. bit 7-5 bit 4 bit 3 bit 2 bit 1 bit 0 Note 1: 2: DS39995B-page 34  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 3-2: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-4 bit 3 HSC = Hardware Settable/Clearable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — R/C-0, HSC IPL3(1) R/W-0 PSV U-0 — U-0 — bit 0 CORCON: CPU CONTROL REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 Unimplemented: Read as ‘0’ IPL3: CPU Interrupt Priority Level Status bit(1) 1 = CPU interrupt priority level is greater than 7 0 = CPU interrupt priority level is 7 or less PSV: Program Space Visibility in Data Space Enable bit 1 = Program space is visible in data space 0 = Program space is not visible in data space Unimplemented: Read as ‘0’ User interrupts are disabled when IPL3 = 1. The PIC24F CPU incorporates hardware support for both multiplication and division. This includes a dedicated hardware multiplier and support hardware division for 16-bit divisor. bit 2 bit 1-0 Note 1: 3.3 Arithmetic Logic Unit (ALU) The PIC24F ALU is 16 bits wide and is capable of addition, subtraction, bit shifts and logic operations. Unless otherwise mentioned, arithmetic operations are 2’s complement in nature. Depending on the operation, the ALU may affect the values of the Carry (C), Zero (Z), Negative (N), Overflow (OV) and Digit Carry (DC) Status bits in the SR register. The C and DC Status bits operate as Borrow and Digit Borrow bits, respectively, for subtraction operations. The ALU can perform 8-bit or 16-bit operations, depending on the mode of the instruction that is used. Data for the ALU operation can come from the W register array, or data memory, depending on the addressing mode of the instruction. Likewise, output data from the ALU can be written to the W register array or a data memory location. 3.3.1 MULTIPLIER The ALU contains a high-speed, 17-bit x 17-bit multiplier. It supports unsigned, signed or mixed sign operation in several multiplication modes: • • • • • • • 16-bit x 16-bit signed 16-bit x 16-bit unsigned 16-bit signed x 5-bit (literal) unsigned 16-bit unsigned x 16-bit unsigned 16-bit unsigned x 5-bit (literal) unsigned 16-bit unsigned x 16-bit signed 8-bit unsigned x 8-bit unsigned  2011 Microchip Technology Inc. DS39995B-page 35 PIC24FV32KA304 FAMILY 3.3.2 DIVIDER 3.3.3 MULTI-BIT SHIFT SUPPORT The divide block supports 32-bit/16-bit and 16-bit/16-bit signed and unsigned integer divide operations with the following data sizes: 1. 2. 3. 4. 32-bit signed/16-bit signed divide 32-bit unsigned/16-bit unsigned divide 16-bit signed/16-bit signed divide 16-bit unsigned/16-bit unsigned divide The PIC24F ALU supports both single bit and single-cycle, multi-bit arithmetic and logic shifts. Multi-bit shifts are implemented using a shifter block, capable of performing up to a 15-bit arithmetic right shift, or up to a 15-bit left shift, in a single cycle. All multi-bit shift instructions only support Register Direct Addressing for both the operand source and result destination. A full summary of instructions that use the shift operation is provided in Table 3-2. The quotient for all divide instructions ends up in W0 and the remainder in W1. Sixteen-bit signed and unsigned DIV instructions can specify any W register for both the 16-bit divisor (Wn), and any W register (aligned) pair (W(m + 1):Wm) for the 32-bit dividend. The divide algorithm takes one cycle per bit of divisor, so both 32-bit/16-bit and 16-bit/16-bit instructions take the same number of cycles to execute. TABLE 3-2: Instruction ASR SL LSR INSTRUCTIONS THAT USE THE SINGLE AND MULTI-BIT SHIFT OPERATION Description Arithmetic shift right source register by one or more bits. Shift left source register by one or more bits. Logical shift right source register by one or more bits. DS39995B-page 36  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 4.0 MEMORY ORGANIZATION As Harvard architecture devices, the PIC24F microcontrollers feature separate program and data memory space and bussing. This architecture also allows the direct access of program memory from the data space during code execution. User access to the program memory space is restricted to the lower half of the address range (000000h to 7FFFFFh). The exception is the use of TBLRD/TBLWT operations, which use TBLPAG to permit access to the Configuration bits and Device ID sections of the configuration memory space. Memory maps for the PIC24FV32KA304 family of devices are shown in Figure 4-1. 4.1 Program Address Space The program address memory space of the PIC24FV32KA304 family is 4M instructions. The space is addressable by a 24-bit value derived from either the 23-bit Program Counter (PC) during program execution, or from a table operation or data space remapping, as described in Section 4.3 “Interfacing Program and Data Memory Spaces”. FIGURE 4-1: PROGRAM SPACE MEMORY MAP FOR PIC24FV32KA304 FAMILY DEVICES PIC24FV16KA304 GOTO Instruction Reset Address Interrupt Vector Table Reserved Alternate Vector Table PIC24FV32KA304 GOTO Instruction Reset Address Interrupt Vector Table Reserved Alternate Vector Table 000000h 000002h 000004h 0000FEh 000100h 000104h 0001FEh 000200h User Memory Space Flash Program Memory (5632 instructions) User Flash Program Memory (11264 instructions) 002BFEh Unimplemented Read ‘0’ Unimplemented Read ‘0’ Data EEPROM 0057FEh 7FFE00h 7FFFFFh 800000h Data EEPROM Configuration Memory Space Reserved Reserved Device Config Registers Device Config Registers F7FFFEh F80000h F80010h F80012h Reserved Reserved DEVID (2) DEVID (2) FEFFFEh FF0000h FFFFFFh Note: Memory areas are not displayed to scale. DS39995B-page 37  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 4.1.1 PROGRAM MEMORY ORGANIZATION 4.1.3 DATA EEPROM The program memory space is organized in word-addressable blocks. Although it is treated as 24 bits wide, it is more appropriate to think of each address of the program memory as a lower and upper word, with the upper byte of the upper word being unimplemented. The lower word always has an even address, while the upper word has an odd address, as shown in Figure 4-2. Program memory addresses are always word-aligned on the lower word, and addresses are incremented or decremented by two during code execution. This arrangement also provides compatibility with data memory space addressing and makes it possible to access data in the program memory space. In the PIC24FV32KA304 family, the data EEPROM is mapped to the top of the user program memory space, starting at address, 7FFE00, and expanding up to address, 7FFFFF. The data EEPROM is organized as 16-bit wide memory and 256 words deep. This memory is accessed using table read and write operations similar to the user code memory. 4.1.4 DEVICE CONFIGURATION WORDS Table 4-1 provides the addresses of the device Configuration Words for the PIC24FV32KA304 family. Their location in the memory map is shown in Figure 4-1. For more information on device Configuration Words, see Section 26.0 “Special Features”. 4.1.2 HARD MEMORY VECTORS All PIC24F devices reserve the addresses between 00000h and 000200h for hard coded program execution vectors. A hardware Reset vector is provided to redirect code execution from the default value of the PC on device Reset to the actual start of code. A GOTO instruction is programmed by the user at 000000h, with the actual address for the start of code at 000002h. PIC24F devices also have two interrupt vector tables, located from 000004h to 0000FFh and 000104h to 0001FFh. These vector tables allow each of the many device interrupt sources to be handled by separate ISRs. A more detailed discussion of the interrupt vector tables is provided in Section 8.1 “Interrupt Vector (IVT) Table”. TABLE 4-1: DEVICE CONFIGURATION WORDS FOR PIC24FV32KA304 FAMILY DEVICES Configuration Word Addresses F80000 F80004 F80006 F80008 F8000A F8000C F8000E F80010 Configuration Words FBS FGS FOSCSEL FOSC FWDT FPOR FICD FDS FIGURE 4-2: PROGRAM MEMORY ORGANIZATION msw Address 000001h 000003h 000005h 000007h most significant word 23 00000000 00000000 00000000 00000000 Program Memory ‘Phantom’ Byte (read as ‘0’) Instruction Width 16 least significant word 8 0 000000h 000002h 000004h 000006h PC Address (lsw Address)  2011 Microchip Technology Inc. DS39995B-page 38 PIC24FV32KA304 FAMILY 4.2 Data Address Space The PIC24F core has a separate, 16-bit wide data memory space, addressable as a single linear range. The data space is accessed using two Address Generation Units (AGUs), one each for read and write operations. The data space memory map is shown in Figure 4-3. All Effective Addresses (EAs) in the data memory space are 16 bits wide and point to bytes within the data space. This gives a data space address range of 64 Kbytes or 32K words. The lower half of the data memory space (that is, when EA = 0) is used for implemented memory addresses, while the upper half (EA = 1) is reserved for the Program Space Visibility (PSV) area (see Section 4.3.3 “Reading Data From Program Memory Using Program Space Visibility”). PIC24FV32KA304 family devices implement a total of 1024 words of data memory. If an EA points to a location outside of this area, an all zero word or byte will be returned. 4.2.1 DATA SPACE WIDTH The data memory space is organized in byte-addressable, 16-bit wide blocks. Data is aligned in data memory and registers as 16-bit words, but all the data space EAs resolve to bytes. The Least Significant Bytes (LSBs) of each word have even addresses, while the Most Significant Bytes (MSBs) have odd addresses. FIGURE 4-3: DATA SPACE MEMORY MAP FOR PIC24FV32KA304 FAMILY DEVICES MSB Address 0001h 07FFh 0801h Implemented Data RAM MSB SFR Space LSB LSB Address 0000h 07FEh 0800h SFR Space Near Data Space Data RAM 0FFFh 1FFF Unimplemented Read as ‘0’ 7FFFh 8001h 7FFFh 8000h 0FFEh 1FFEh Program Space Visibility Area FFFFh FFFEh Note: Data memory areas are not shown to scale. DS39995B-page 39  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 4.2.2 DATA MEMORY ORGANIZATION AND ALIGNMENT To maintain backward compatibility with PIC® devices and improve data space memory usage efficiency, the PIC24F instruction set supports both word and byte operations. As a consequence of byte accessibility, all Effective Address (EA) calculations are internally scaled to step through word-aligned memory. For example, the core recognizes that Post-Modified Register Indirect Addressing mode [Ws++] will result in a value of Ws + 1 for byte operations and Ws + 2 for word operations. Data byte reads will read the complete word, which contains the byte, using the LSB of any EA to determine which byte to select. The selected byte is placed onto the LSB of the data path. That is, data memory and the registers are organized as two parallel, byte-wide entities with shared (word) address decode, but separate write lines. Data byte writes only write to the corresponding side of the array or register, which matches the byte address. All word accesses must be aligned to an even address. Misaligned word data fetches are not supported, so care must be taken when mixing byte and word operations, or translating from 8-bit MCU code. If a misaligned read or write is attempted, an address error trap will be generated. If the error occurred on a read, the instruction underway is completed; if it occurred on a write, the instruction will be executed, but the write will not occur. In either case, a trap is then executed, allowing the system and/or user to examine the machine state prior to execution of the address Fault. All byte loads into any W register are loaded into the LSB. The MSB is not modified. A Sign-Extend (SE) instruction is provided to allow the users to translate 8-bit signed data to 16-bit signed values. Alternatively, for 16-bit unsigned data, users can clear the MSB of any W register by executing a Zero-Extend (ZE) instruction on the appropriate address. Although most instructions are capable of operating on word or byte data sizes, it should be noted that some instructions operate only on words. 4.2.3 NEAR DATA SPACE The 8-Kbyte area between 0000h and 1FFFh is referred to as the near data space. Locations in this space are directly addressable via a 13-bit absolute address field within all memory direct instructions. The remainder of the data space is addressable indirectly. Additionally, the whole data space is addressable using MOV instructions, which support Memory Direct Addressing (MDA) with a 16-bit address field. For PIC24FV32KA304 family devices, the entire implemented data memory lies in Near Data Space (NDS). 4.2.4 SFR SPACE The first 2 Kbytes of the near data space, from 0000h to 07FFh, are primarily occupied with Special Function Registers (SFRs). These are used by the PIC24F core and peripheral modules for controlling the operation of the device. SFRs are distributed among the modules that they control and are generally grouped together by the module. Much of the SFR space contains unused addresses; these are read as ‘0’. The SFR space, where the SFRs are actually implemented, is provided in Table 4-2. Each implemented area indicates a 32-byte region, where at least one address is implemented as an SFR. A complete listing of implemented SFRs, including their addresses, is provided in Table 4-3 through Table 4-25. TABLE 4-2: IMPLEMENTED REGIONS OF SFR DATA SPACE SFR Space Address xx00 xx20 Core Timers I2 C™ — — — — UART ADC/CMTU — — RTC/Comp — — — CRC System/DS/HLVD — — — NVM/PMD — — Capture SPI xx40 xx60 ICN — — — — — xx80 Compare xxA0 Interrupts — — — — — — — — — — — — I/O — — — xxC0 xxE0 — — 000h 100h 200h 300h 400h 500h 600h 700h Legend: — = No implemented SFRs in this block.  2011 Microchip Technology Inc. DS39995B-page 40 TABLE 4-3: File Name WREG0 WREG1 WREG2 WREG3 WREG4 WREG5 WREG6 WREG7 WREG8 WREG9 WREG10 WREG11 WREG12 WREG13 WREG14 WREG15 SPLIM PCL PCH TBLPAG PSVPAG RCOUNT SR CORCON DISICNT Legend: Start Addr 0000 0002 0004 0006 0008 000A 000C 000E 0010 0012 0014 0016 0018 001A 001C 001E 0020 002E 0030 0032 0034 0036 0042 0044 0052 CPU CORE REGISTERS MAP Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 WREG0 WREG1 WREG2 WREG3 WREG4 WREG5 WREG6 WREG7 WREG8 WREG9 WREG10 WREG11 WREG12 WREG13 WREG14 WREG15 SPLIM PCL — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — RCOUNT DC — IPL2 — DISICNT IPL1 — IPL0 — RA — N IPL3 OV PSV Z — C — — PCH TBLPAG PSVPAG Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 xxxx 0000 0000 0000 0000 xxxxx 0000 0000 xxxx DS39995B-page 41  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.  2011 Microchip Technology Inc. DS39995B-page 42 TABLE 4-4: File Addr Name Bit 15 ICN REGISTER MAP Bit 14 CN14PDE CN30PDE — CN14IE CN30IE — CN14PUE CN30PUE — Bit 13 CN13PDE CN29PDE — CN13IE CN29IE — CN13PUE CN29PUE — Bit 12 CN12PDE CN28PDE — CN12IE CN28IE(1,2) — CN12PUE — (1,2) Bit 11 Bit 10 Bit 9 CN9PDE(1) CN25PDE — CN9IE(1) CN25IE(1,2) — CN9PUE(1) — (1,2) Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 CN4PDE Bit 3 CN3PDE Bit 2 CN2PDE Bit 1 CN1PDE Bit 0 CN0PDE All Resets 0000 0000 CNPD1 0056 CN15PDE(1) CNPD2 0058 CN31PDE CNPD3 005A CNEN1 0062 CNEN2 0064 CNEN3 0066 — CN15IE(1) CN31IE(1,2) — (1,2) CN11PDE CN10PDE(1,2) CN27PDE — CN11IE CN27IE(1) — (1) CN8PDE(3) CN7PDE(1) CN6PDE CN5PDE — CN8IE(3) CN24IE(1) — — CN7IE(1) CN23IE — — CN6IE CN22IE — — CN5IE CN21IE — CN26PDE — (1,2) CN24PDE(1) CN23PDE CN22PDE CN21PDE CN20PDE(1,2) CN19PDE(1,2) CN18PDE(1,2) CN17PDE(1,2) CN16PDE(1) CN4IE CN20IE(1,2) CN36IE(1,2) CN4PUE CN3IE CN19IE(1,2) CN35IE(1,2) CN3PUE CN2IE CN18IE(1,2) CN34IE(1,2) CN2PUE CN1IE CN17IE(1,2) CN33IE(1,2) CN1PUE CN0IE CN16IE(1) CN32IE(1,2) CN0PUE CN36PDE(1,2) CN35PDE(1,2) CN34PDE(1,2) CN33PDE(1,2) CN32PDE(1,2) 0000 0000 0000 0000 0000 0000 CN10IE(1,2) CN26IE(1,2) — CNPU1 006E CN15PUE(1) CNPU2 0070 CN31PUE(1,2) CNPU3 0072 Legend: Note 1: 2: 3: — CN11PUE CN10PUE(1,2) — — CN8PUE(3) CN7PUE(1) CN6PUE CN5PUE — — — — CN28PUE(1,2) CN27PUE(1) CN26PUE(1,2) CN25PUE(1,2) CN24PUE(1) CN23PUE CN22PUE CN21PUE CN20PUE(1,2) CN19PUE(1,2) CN18PUE(1,2) CN17PUE(1,2) CN16PUE(1) CN36PUE(1,2) CN35PUE(1,2) CN34PUE(1,2) CN33PUE(1,2) CN32PUE(1,2) 0000 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. These bits are not implemented in 20-pin devices. These bits are not implemented in 28-pin devices. These bits are not implemented in ‘FV’ devices. PIC24FV32KA304 FAMILY TABLE 4-5: File Name Addr INTERRUPT CONTROLLER REGISTER MAP Bit 15 Bit 14 — DISI — U2RXIF — RTCIF — — — U2RXIE — RTCIE — — T1IP2 T2IP2 NVMIP2 CNIP2 — T4IP2 — — — — CRCIP2 — — — — Bit 13 — — AD1IF INT2IF — — CTMUIF — AD1IE INT2IE — — CTMUIE — T1IP1 T2IP1 NVMIP1 CNIP1 — T4IP1 — — — — CRCIP1 — — — VHOLD Bit 12 — — U1TXIF T5IF — — — — U1TXIE T5IE — — — — T1IP0 T2IP0 NVMIP0 CNIP0 — T4IP0 — — — — CRCIP0 — — — — Bit 11 — — U1RXIF T4IF — — — — U1RXIE T4IE — — — — — — — — — — — — — — — — — — — — ILR3 Bit 10 — — SPI1IF — — — — — SPI1IE — — — — — OC1IP2 OC2IP2 SPI1IP2 — CMIP2 — — U2RXIP2 — — RTCIP2 U2ERIP2 — — — ILR2 Bit 9 — — SPF1IF OC3IF — — — — SPF1IE OC3IE — — — — OC1IP1 OC2IP1 SPI1IP1 — CMIP1 — — U2RXIP1 — — RTCIP1 U2ERIP1 — — — ILR1 Bit 8 — — T3IF — — — HLVDIF — T3IE — — — HLVDIE — OC1IP0 OC2IP0 SPI1IP0 — CMIP0 — — U2RXIP0 — — RTCIP0 U2ERIP0 — — — ILR0 Bit 7 — — T2IF — — — — — T2IE — — — — — — — — — — — — — — — — — — — — — — Bit 6 — — OC2IF — — — — — OC2IE — — — — — IC1IP2 IC2IP2 SPF1IP2 AD1IP2 MI2C1P2 — OC3IP2 INT2IP2 SPI2IP2 IC3IP2 SI2C2IP2 — U1ERIP2 — CTMUIP2 — Bit 5 — — IC2IF — IC3IF — — — IC2IE — IC3IE — — — IC1IP1 IC2IP1 SPF1IP1 AD1IP1 MI2C1P1 — OC3IP1 INT2IP1 SPI2IP1 IC3IP1 SI2C2IP1 — U1ERIP1 — CTMUIP1 — Bit 4 Bit 3 Bit 2 STKERR INT2EP OC1IF CMIF — MI2C2IF U2ERIF — OC1IE CMIE — MI2C2IE U2ERIE — INT0IP2 — T3IP2 U1TXIP2 SI2C1P2 INT1IP2 — T5IP2 SPF2IP2 — — — — HLVDIP2 — Bit 1 OSCFAIL INT1EP IC1IF MI2C1IF SPI2IF SI2C2IF U1ERIF — IC1IE MI2C1IE SPI2IE SI2C2IE U1ERIE — INT0IP1 — T3IP1 U1TXIP1 SI2C1P1 INT1IP1 — T5IP1 SPF2IP1 — — — — HLVDIP1 — Bit 0 — INT0EP INT0IF SI2C1IF SPF2IF — — ULPWUIF INT0IE SI2C1IE SPF2IE — — ULPWUIE INT0IP0 — T3IP0 U1TXIP0 SI2C1P0 INT1IP0 — T5IP0 SPF2IP0 — — — — HLVDIP0 — All Resets 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 4444 4444 4444 4044 4444 0004 4040 4440 0044 0040 0440 0400 4440 0004 0040 0000 0000 DS39995B-page 43  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY INTCON1 0080 NSTDIS INTCON2 0082 IFS0 IFS1 IFS2 IFS3 IFS4 IFS5 IEC0 IEC1 IEC2 IEC3 IEC4 IEC5 IPC0 IPC1 IPC2 IPC3 IPC4 IPC5 IPC6 IPC7 IPC8 IPC9 IPC12 IPC15 IPC16 IPC18 IPC19 IPC20 0084 0086 0088 008A 008C 008E 0094 0096 0098 009A 009C 009E 00A4 00A6 00A8 00AA 00AC 00AE 00B0 00B2 00B4 00B6 00BC 00C2 00C4 00C8 00CA 00CC ALTIVT NVMIF U2TXIF — — — — NVMIE U2TXIE — — — — — — — — — — — — — — — — — — — — MATHERR ADDRERR — — INT1IF — — — — — INT1IE — — — — IC1IP0 IC2IP0 SPF1IP0 AD1IP0 MI2C1P0 — OC3IP0 INT2IP0 SPI2IP0 IC3IP0 SI2C2IP0 — U1ERIP0 — CTMUIP0 — — T1IF CNIF — — CRCIF — T1IE CNIE — — CRCIE — — — — — — — — — — — — — — — — — U1RXIP2 U1RXIP1 U1RXIP0 U2TXIP2 U2TXIP1 U2TXIP0 MI2C2IP2 MI2C2IP1 MI2C2IP0 ULPWUIP2 ULPWUIP1 ULPWUIP0 VECNUM1 VECNUM0 INTTREG 00E0 CPUIRQ Legend: VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.  2011 Microchip Technology Inc. DS39995B-page 44 TABLE 4-6: File Name TMR1 PR1 T1CON TMR2 TMR3HLD TMR3 PR2 PR3 T2CON T3CON TMR4 TMR5HLD TMR5 PR4 PR5 T4CON T5CON Legend: Addr 0100 0102 0104 0106 0108 010A 010C 010E 0110 0112 0114 0116 0118 011A 011C 011E 0120 TIMER REGISTER MAP Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 TMR1 PR1 TON — TSIDL — — — T1ECS1 T1ECS0 TMR2 TMR3HLD TMR3 PR2 PR3 TON TON — — TSIDL TSIDL — — — — — — — — — — TMR4 TMR5HLD TMR5 PR4 PR5 TON TON — — TSIDL TSIDL — — — — — — — — — — — — TGATE TGATE TCKPS1 TCKPS1 TCKPS0 TCKPS0 T45 — — — TCS TCS — — — — TGATE TGATE TCKPS1 TCKPS1 TCKPS0 TCKPS0 T32 — — — TCS TCS — — — TGATE TCKPS1 TCKPS0 — TSYNC TCS — Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0000 FFFF 0000 0000 0000 0000 0000 FFFF FFFF 0000 0000 0000 0000 PIC24FV32KA304 FAMILY FFFF FFFF 0000 0000 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-7: File Name IC1CON1 IC1CON2 IC1BUF IC1TMR IC2CON1 IC2BUF IC2TMR IC3CON1 IC3CON2 IC3BUF IC3TMR Legend: INPUT CAPTURE REGISTER MAP Bit 14 — — Bit 13 ICSIDL — Bit 12 ICTSEL2 — Bit 11 ICTSEL1 — Bit 10 ICTSEL0 — Bit 9 — — Bit 8 — IC32 Bit 7 — ICTRIG IC1BUF IC1TMR — — — — ICSIDL — IC2TSEL2 IC2TSEL1 IC2TSEL0 — — — — — — IC32 — ICTRIG IC2BUF IC2TMR — — — — ICSIDL — IC3TSEL2 IC3TSEL1 IC3TSEL0 — — — — — — IC32 — ICTRIG IC3BUF IC3TMR ICI1 TRIGSTAT ICI0 — ICOV ICBNE ICM2 ICM1 ICM0 SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 ICI1 TRIGSTAT ICI0 — ICOV ICBNE ICM2 ICM1 ICM0 SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 Bit 6 ICI1 TRIGSTAT Bit 5 ICI0 — Bit 4 ICOV Bit 3 ICBNE Bit 2 ICM2 Bit 1 ICM1 Bit 0 ICM0 All Resets 0000 000D 0000 xxxx 0000 000D 0000 xxxx 0000 000D 0000 xxxx Addr Bit 15 0140 0142 0144 0146 0148 014C 014E 0150 0152 0154 0156 — — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 IC2CON2 014A — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. DS39995B-page 45  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 4-8: File Name Addr OC1CON1 0190 OC1RS OC1R OC1TMR 0194 0196 0198 OUTPUT COMPARE REGISTER MAP Bit 15 — Bit 14 — Bit 13 OCSIDL Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 OCFLT0 Bit 3 TRIGMODE Bit 2 OCM2 Bit 1 OCM1 Bit 0 OCM0 All Resets 0000 000C 0000 0000 xxxx OCFLT2 OCFLT1 OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 000C 0000 0000 xxxx OCFLT2 OCFLT1 OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 000C 0000 0000 xxxx OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2 ENFLT1 ENFLT0 OCINV — DCB1 DCB0 OC32 OC1RS OC1R OC1TMR OCFLT2 OCFLT1 OC1CON2 0192 FLTMD FLTOUT FLTTRIEN OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 OC2CON1 019A OC2RS OC2R OC2TMR 019E 01A0 01A2 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2 ENFLT1 ENFLT0 OCINV — DCB1 DCB0 OC32 OC2RS OC2R OC2TMR OC2CON2 019C FLTMD FLTOUT FLTTRIEN OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 OC3CON1 01A4 OC3RS OC3R OC3TMR Legend: 01A8 01AA 01AC — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2 ENFLT1 ENFLT0 OCINV — DCB1 DCB0 OC32 OC3RS OC3R OC3TMR OC3CON2 01A6 FLTMD FLTOUT FLTTRIEN OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.  2011 Microchip Technology Inc. DS39995B-page 46 TABLE 4-9: File Name I2C1RCV I2C1TRN I2C1BRG I2C1CON I2C1STAT I2C1ADD I2C1MSK I2C2RCV I2C2TRN I2C2BRG I2C2CON I2C2STAT I2C2ADD I2C2MSK Legend: Addr 0200 0202 0204 0206 0208 020A 020C 0210 0212 0214 0216 0218 021A 021C I2C™ REGISTER MAP Bit 15 — — — I2CEN ACKSTAT — — — — — I2CEN ACKSTAT — — Bit 14 — — — — TRSTAT — — — — — — TRSTAT — — Bit 13 — — — — — — — — — — — — Bit 12 — — — — — — — — — — — — Bit 11 — — — — — — — — — — — — Bit 10 — — — A10M BCL — — — — — A10M BCL — — AMSK9 AMSK8 AMSK7 AMSK6 AMSK9 — — — DISSLW GCSTAT AMSK8 — — — SMEN ADD10 GCEN IWCOL STREN I2COV ACKDT D/A I2CADD AMSK5 AMSK4 AMSK3 AMSK2 AMSK1 AMSK0 P AMSK7 AMSK6 Bit 9 — — — DISSLW GCSTAT Bit 8 — — — SMEN ADD10 GCEN IWCOL STREN I2COV ACKDT D/A I2CADD AMSK5 AMSK4 AMSK3 AMSK2 AMSK1 AMSK0 I2CRCV I2CTRN I2CBRG ACKEN RCEN S PEN R/W RSEN RBF SEN TBF P Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0000 00FF 0000 PEN R/W RSEN RBF SEN TBF 1000 0000 0000 0000 0000 00FF 0000 1000 0000 0000 0000 I2CRCV I2CTRN I2CBRG ACKEN RCEN S I2CSIDL SCLREL IPMIEN I2CSIDL SCLREL IPMIEN PIC24FV32KA304 FAMILY — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-10: File Name U1MODE U1STA U1TXREG U1RXREG U1BRG U2MODE U2STA U2TXREG U2RXREG U2BRG Legend: Addr 0220 0222 0224 0226 0228 0230 0232 0234 0236 0238 UART REGISTER MAP Bit 15 UARTEN — — UARTEN — — Bit 14 — — — — — — Bit 13 USIDL — — USIDL — — Bit 12 IREN — — — IREN — — — Bit 11 RTSMD — — RTSMD — — Bit 10 — — — — — — Bit 9 UEN1 UTXBF — — BRG UEN1 UTXBF — — BRG UEN0 TRMT WAKE URXISEL1 LPBACK URXISEL0 ABAUD ADDEN RXINV RIDLE BRGH PERR PDSEL1 PDSEL0 STSEL FERR OERR URXDA UTXISEL1 UTXINV UTXISEL0 UTXBRK UTXEN Bit 8 UEN0 TRMT Bit 7 WAKE URXISEL1 Bit 6 LPBACK URXISEL0 Bit 5 ABAUD ADDEN Bit 4 RXINV RIDLE Bit 3 BRGH PERR Bit 2 Bit 1 Bit 0 All Resets 0000 0110 xxxx 0000 0000 0000 0110 xxxx 0000 0000 PDSEL1 PDSEL0 STSEL FERR OERR URXDA UTXISEL1 UTXINV UTXISEL0 UTXBRK UTXEN U1TXREG U1RXREG U2TXREG U2RXREG — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. DS39995B-page 47  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 4-11: File Name SPI1STAT SPI1CON1 SPI1CON2 SPI1BUF SPI2STAT SPI2CON1 SPI2CON2 SPI2BUF Legend: Addr 0240 0242 0244 0248 0260 0262 0264 0268 SPI REGISTER MAP Bit 15 SPIEN — FRMEN SPIEN — FRMEN Bit 14 — — SPIFSD — — SPIFSD Bit 13 SPISIDL — SPIFPOL SPISIDL — SPIFPOL Bit 12 — DISSCK — — DISSCK — Bit 11 — DISSDO — — DISSDO — Bit 10 Bit 9 Bit 8 Bit 7 SRMPT SSEN — SRMPT SSEN — Bit 6 SPIROV CKP — SPIROV CKP — Bit 5 SR1MPT MSTEN — SRXMPT MSTEN — Bit 4 SISEL2 SPRE2 — SISEL2 SPRE2 — Bit 3 SISEL1 SPRE1 — SISEL1 SPRE1 — Bit 2 SISEL0 SPRE0 — SISEL0 SPRE0 — Bit 1 SPITBF PPRE1 SPIFE SPITBF PPRE1 SPIFE Bit 0 SPIRBF PPRE0 SPIBEN SPIRBF PPRE0 SPIBEN All Resets 0000 0000 0000 0000 0000 0000 0000 0000 SPIBEC2 SPIBEC1 SPIBEC0 MODE16 — SMP — CKE — SPI1BUF SPIBEC2 SPIBEC1 SPIBEC0 MODE16 — SMP — CKE — SPI2BUF — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-12: File Name TRISA PORTA LATA ODCA Legend: Note 1: 2: 3: 4: Addr 02C0 02C2 02C4 02C6 PORTA REGISTER MAP Bit 15 — — — — Bit 14 — — — — Bit 13 — — — — Bit 12 — — — — Bit 11(2,3) TRISA11 RA11 LATA11 ODA11 Bit 10(2,3) TRISA10 RA10 LATA10 ODA10 Bit 9(2,3) TRISA9 RA9 LATA9 ODA9 Bit 8(2,3) TRISA8 RA8 LATA8 ODA8 Bit 7(2) TRISA7 RA7 LATA7 ODA7 Bit 6(4) TRISA6 RA6 LATA6 ODA6 Bit 5(1) — RA5 — — Bit 4 TRISA4 RA4 LATA4 ODA4 Bit 3 TRISA3 RA3 LATA3 ODA3 Bit 2 TRISA2 RA2 LATA2 ODA2 Bit 1 TRISA1 RA1 LATA1 ODA1 Bit 0 TRISA0 RA0 LATA0 ODA0 All Resets 00DF xxxx xxxx 0000 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. This bit is available only when MCLRE = 1. These bits are not implemented in 20-pin devices. These bits are not implemented in 28-pin devices. These bits are not implemented in FV devices. TABLE 4-13: File Name TRISB LATB ODCB Legend: Note 1: Addr 02C8 02CC 02CE PORTB REGISTER MAP Bit 15 Bit 14 TRISB14 RB14 LATB14 ODB14 Bit 13 TRISB13 RB13 LATB13 ODB13 Bit 12 TRISB12 RB12 LATB12 ODB12 Bit 11(1) TRISB11 RB11 LATB11 ODB11 Bit 10(1) TRISB10 RB10 LATB10 ODB10 Bit 9 TRISB9 RB9 LATB9 ODB9 Bit 8 TRISB8 RB8 LATB8 ODB8 Bit 7 TRISB7 RB7 LATB7 ODB7 Bit 6(1) TRISB6 RB6 LATB6 ODB6 Bit 5(1) TRISB5 RB5 LATB5 ODB5 Bit 4 TRISB4 RB4 LATB4 ODB4 Bit 3(1) TRISB3 RB3 LATB3 ODB3 Bit 2 TRISB2 RB2 LATB2 ODB2 Bit 1 TRISB1 RB1 LATB1 ODB1 Bit 0 TRISB0 RB0 LATB0 ODB0 All Resets FFFF xxxx xxxx 0000 TRISB15 RB15 LATB15 ODB15 PORTB 02CA — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. These bits not implemented in 20-pin devices.  2011 Microchip Technology Inc. DS39995B-page 48 TABLE 4-14: File Name TRISC LATC ODCC Legend: Note 1: Addr 02D0 02D4 02D6 PORTC REGISTER MAP(1) Bit 15 — — — — Bit 14 — — — — Bit 13 — — — — Bit 12 — — — — Bit 11 — — — — Bit 10 — — — — Bit 9 TRISC9 RC9 LATC9 ODC9 Bit 8 TRISC8 RC8 LATC8 ODC8 Bit 7 TRISC7 RC7 LATC7 ODC7 Bit 6 TRISC6 RC6 LATC6 ODC6 Bit 5 TRISC5 RC5 LATC5 ODC5 Bit 4 TRISC4 RC4 LATC4 ODC4 Bit 3 TRISC3 RC3 LATC3 ODC3 Bit 2 TRISC2 RC2 LATC2 ODC2 Bit 1 TRISC1 RC1 LATC1 ODC1 Bit 0 TRISC0 RC0 LATC0 ODC0 All Resets 03FF xxxx xxxx 0000 PORTC 02D2 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. PORTC is not implemented in 20-pin devices or 28-pin devices. TABLE 4-15: File Name PADCFG1 Legend: Addr 02FC PAD CONFIGURATION REGISTER MAP Bit 15 — Bit 14 — Bit 13 — Bit 12 — Bit 11 — Bit 10 — Bit 9 — Bit 8 — Bit 7 — Bit 6 — Bit 5 Bit 4 Bit 3 — Bit 2 — Bit 1 — Bit 0 — All Resets 0000 SMBUSDEL2 SMBUSDEL1 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. PIC24FV32KA304 FAMILY DS39995B-page 49  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 4-16: File Name ADC1BUF0 ADC1BUF1 ADC1BUF2 ADC1BUF3 ADC1BUF4 ADC1BUF5 ADC1BUF6 ADC1BUF7 ADC1BUF8 ADC1BUF9 ADC1BUF11 Addr 0300 0302 0304 0306 0308 030A 030C 030E 0310 0312 0316 ADC REGISTER MAP Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 ADC1BUF0 ADC1BUF1 ADC1BUF2 ADC1BUF3 ADC1BUF4 ADC1BUF5 ADC1BUF6 ADC1BUF7 ADC1BUF8 ADC1BUF9 ADC1BUF10 ADC1BUF11 ADC1BUF12 ADC1BUF13 ADC1BUF14 ADC1BUF15 ADC1BUF16 ADC1BUF17 ADON ADRC — CSSL15 ASEN — CHH15 — PVCFG0 EXTSAM CH0NB1 CSSL30 CSSL14 LPEN — CHH14 ADSIDL NVCFG0 — CH0NB0 CSSL29 CSSL13 CTMUREQ — CHH13 — SAMC4 CH0SB4 CSSL28 CSSL12 BGREQ — CHH12 — SAMC3 CH0SB3 CSSL27 CSSL11 VRSREQ — CHH11 — SAMC2 CH0SB2 CSSL26 CSSL10 — — CHH10 FORM1 — SAMC1 CH0SB1 — CSSL9 ASINT1 — CHH9 FORM0 — SAMC0 CH0SB0 — CSSL8 ASINT0 — CHH8 SSRC3 BUFS ADCS7 — CSSL7 — — CHH7 SSRC2 SMPI4 ADCS6 — CSSL6 — — CHH6 SSRC1 SMPI3 ADCS5 — CSSL5 — — CHH5 SSRC0 SMPI2 ADCS4 — CSSL4 — — CHH4 — SMPI1 ADCS3 CH0SA3 — CSSL3 WM1 — CHH3 ASAM SMPI0 ADCS2 CH0SA2 — CSSL2 WM0 — CHH2 SAMP BUFM ADCS1 DONE ALTS ADCS0 OFFCAL BUFREGEN CSCNA Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx 0000 0000 0000 0000 0000 0000 0000 0000 0000 ADC1BUF10 0314 ADC1BUF12 0318 ADC1BUF13 031A ADC1BUF14 031C ADC1BUF15 031E ADC1BUF16 0320 ADC1BUF17 0322 AD1CON1 AD1CON2 AD1CON3 AD1CHS AD1CSSH AD1CSSL AD1CON5 AD1CHITH AD1CHITL Legend: 0340 0344 034E 0350 0354 0356 0358 0342 PVCFG1 0348 CH0NB2 CH0NA2 CH0NA1 CH0NA0 CH0SA4 CH0SA1 CH0SA0 CSSL17 CSSL16 CSSL1 CM1 CHH17 CHH1 CSSL0 CM0 CHH16 CHH0 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal.  2011 Microchip Technology Inc. DS39995B-page 50 TABLE 4-17: File Name CTMUCON1 CTMUCON2 CTMUICON AD1CTMUENL Legend: Addr 035A 035E 0362 CTMU REGISTER MAP Bit 15 CTMUEN ITRIM5 — CTMEN15 Bit 14 — ITRIM4 — CTMEN14 Bit 13 CTMUSIDL ITRIM3 — CTMEN13 Bit 12 TGEN ITRIM2 — CTMEN12 Bit 11 EDGEN ITRIM1 — CTMEN11 Bit 10 Bit 9 Bit 8 CTTRIG EDG1 IRNG0 — CTMEN8 Bit 7 — — — CTMEN7 Bit 6 — — — CTMEN6 Bit 5 — — — CTMEN5 Bit 4 — — — CTMEN4 Bit 3 — — — CTMEN3 Bit 2 — — — CTMEN2 Bit 1 — — — CTMEN17 CTMEN1 Bit 0 — — — CTMEN16 CTMEN0 All Resets 0000 0000 0000 0000 0000 EDGSEQEN IDISSEN EDG1SEL0 ITRIM0 — CTMEN10 EDG2 IRNG1 — CTMEN9 035C EDG1EDGE EDG1POL EDG1SEL3 EDG1SEL2 EDG1SEL1 EDG2EDGE EDG2POL EDG2SEL3 EDG2SEL2 EDG2SEL1 EDG2SEL0 AD1CTMUENH 0360 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-18: File Name ANSA ANSB ANSC Legend: Note 1: 2: Addr 04E0 04E2 04E4 ANALOG SELECT REGISTER MAP Bit 15 — — Bit 14 — — Bit 13 — ANSB13 — Bit 12 — ANSB12 — Bit 11 — — — Bit 10 — — — Bit 9 — — — Bit 8 — — — Bit 7 — — — Bit 6 — — — Bit 5 — — — Bit 4 — ANSB4 — Bit 3 ANSA3 ANSB3(1) — Bit 2 ANSA2 ANSB2 Bit 1 ANSA1 ANSB1 Bit 0 ANSA0 ANSB0 ANSC0(1) All Resets 000F F01F 0007 ANSB15 ANSB14 ANSC2(1,2) ANSC1(1,2) — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. These bits are not implemented in 20-pin devices. These bits are not implemented in 28-pin devices. PIC24FV32KA304 FAMILY TABLE 4-19: File Name ALRMVAL RTCVAL RCFGCAL RTCPWC Legend: Addr 0620 REAL-TIME CLOCK AND CALENDAR REGISTER MAP Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets xxxx ARPT7 CAL7 — ARPT6 CAL6 — ARPT5 CAL5 — ARPT4 CAL4 — ARPT3 CAL3 — ARPT2 CAL2 — ARPT1 ARPT0 CAL1 — CAL0 — 0000 xxxx 0000 xxxx ALRMVAL CHIME — AMASK3 RTCWREN AMASK2 RTCSYNC AMASK1 HALFSEC RTCCLK1 AMASK0 RTCOE RTCCLK0 ALRMPTR1 RTCPTR1 RTCOUT1 ALRMPTR0 RTCPTR0 RTCOUT0 RTCVAL RTCEN PWCEN PWCPOL PWCCPRE PWCSPRE ALCFGRPT 0622 ALRMEN 0624 0626 0628 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-20: File Name CMSTAT CVRCON CM1CON CM2CON CM3CON Legend: Addr 0630 0632 0634 0636 0638 TRIPLE COMPARATOR REGISTER MAP Bit 15 CMIDL — CON CON CON Bit 14 — — COE COE COE Bit 13 — — CPOL CPOL CPOL Bit 12 — — CLPWR CLPWR CLPWR Bit 11 — — — — — Bit 10 C3EVT — — — — Bit 9 C2EVT — CEVT CEVT CEVT Bit 8 C1EVT — COUT COUT COUT Bit 7 — CVREN EVPOL1 EVPOL1 EVPOL1 Bit 6 — EVPOL0 EVPOL0 EVPOL0 Bit 5 — — — — Bit 4 — CVR4 CREF CREF CREF Bit 3 — CVR3 — — — Bit 2 C3OUT CVR2 — — — Bit 1 C2OUT CVR1 CCH1 CCH1 CCH1 Bit 0 C1OUT CVR0 CCH0 CCH0 CCH0 All Resets xxxx 0000 xxxx 0000 0000 CVROE CVRSS — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. DS39995B-page 51  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 4-21: File Name CRCCON1 CRCCON2 CRCXORL CRCXORH CRCDATL CRCDATH CRCWDATL CRCWDATH Legend: Addr 0640 0642 0644 0646 0648 064A 064C 064E CRC REGISTER MAP Bit 15 CRCEN — X15 X31 Bit 14 — — X14 X30 Bit 13 CSIDL — X13 X29 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 — PLEN2 X2 X18 Bit 1 — PLEN1 X1 X17 Bit 0 — PLEN0 — X16 All Resets 0000 0000 0000 0000 xxxx xxxx xxxx xxxx VWORD4 VWORD3 VWORD2 VWORD1 VWORD0 CRCFUL CRCMPT CRCISEL CRCGO LENDIAN DWIDTH4 DWIDTH3 DWIDTH2 DWIDTH1 DWIDTH0 X12 X28 X11 X27 X10 X26 X9 X25 X8 X24 CRCDATL CRCDATH CRCWDATL CRCWDATH — X7 X23 — X6 X22 — X5 X21 PLEN4 X4 X20 PLEN3 X3 X19 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-22: File Name RCON OSCCON CLKDIV OSCTUN REFOCON HLVDCON Legend: Note 1: 2: Addr 0740 0742 0744 0748 074E 0756 CLOCK CONTROL REGISTER MAP Bit 15 TRAPR — ROI — ROEN HLVDEN Bit 14 Bit 13 Bit 12 LVREN COSC0 DOZE0 — ROSEL — Bit 11 — — DOZEN — — Bit 10 DPSLP Bit 9 CM Bit 8 PMSLP Bit 7 EXTR — — — VDIR Bit 6 SWR — — — — BGVST Bit 5 SWDTEN LOCK — TUN5 — IRVST Bit 4 WDTO — — TUN4 — — Bit 3 SLEEP CF — TUN3 — HLVDL3 Bit 2 IDLE SOSCDRV — TUN2 — HLVDL2 Bit 1 BOR SOSCEN — TUN1 — HLVDL1 Bit 0 POR — TUN0 — HLVDL0 All Resets (Note 1) IOPUWR SBOREN COSC2 DOZE2 — — — COSC1 DOZE1 — ROSSLP HLSIDL NOSC2 NOSC1 — — — — NOSC0 CLKLOCK — — OSWEN (Note 2) 3140 0000 0000 0000 RCDIV2 RCDIV1 RCDIV0 RODIV3 RODIV2 RODIV1 RODIV0 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. RCON register Reset values are dependent on type of Reset. OSCCON register Reset values are dependent on configuration fuses and by type of Reset. TABLE 4-23: File Name DSCON DSWAKE DSGPR0 DSGPR1 Legend: Note 1: Addr 0758 075A 075C 075E DEEP SLEEP REGISTER MAP Bit 15 DSEN — Bit 14 — — Bit 13 — — Bit 12 — — Bit 11 — — Bit 10 — — Bit 9 — — Bit 8 RTCCWDIS DSINT0 Bit 7 — DSFLT DSGPR0 DSGPR1 Bit 6 — — Bit 5 — — Bit 4 Bit 3 — DSWDT DSRTCC Bit 2 ULPWDIS DSMCLR Bit 1 DSBOR — Bit 0 RELEASE DSPOR All Resets(1) 0000 0000 0000 0000 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. The Deep Sleep registers DSGPR0 and DSGPR1 are only reset on a VDD POR event. TABLE 4-24: File Name NVMCON NVMKEY Legend: Note 1: Addr 0760 0766 NVM REGISTER MAP Bit 15 WR — Bit 14 WREN — Bit 13 WRERR — Bit 12 PGMONLY — Bit 11 — — Bit 10 — — Bit 9 — — Bit 8 — — Bit 7 — Bit 6 ERASE Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets 0000 0000  2011 Microchip Technology Inc. DS39995B-page 52 NVMOP5 NVMOP4 NVMOP3 NVMOP2 NVMOP1 NVMOP0 NVMKEY — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Reset value shown is for POR only. Value on other Reset states is dependent on the state of memory write or erase operations at the time of Reset. TABLE 4-25: File Name ULPWCON Legend: Addr 0768 ULTRA LOW-POWER WAKE-UP REGISTER MAP Bit 15 ULPEN Bit 14 — Bit 13 ULPSIDL Bit 12 — Bit 11 — Bit 10 — Bit 9 — Bit 8 ULPSINK Bit 7 — Bit 6 — Bit 5 — Bit 4 — Bit 3 — Bit 2 — Bit 1 — Bit 0 — All Resets 0000 — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-26: File Name PMD1 PMD2 PMD3 PMD4 Legend: Addr 0770 0772 0774 0776 PMD REGISTER MAP Bit 15 T5MD — — — Bit 14 T4MD — — — Bit 13 T3MD — — — Bit 12 Bit 11 T2MD T1MD — — — — — — Bit 10 — IC3MD CMPMD — Bit 9 — IC2MD RTCCMD — Bit 8 — IC1MD — — Bit 7 I2C1MD — CRCPMD ULPWUMD Bit 6 U2MD — — — Bit 5 U1MD — — — Bit 4 SPI2MD — — EEMD Bit 3 SPI1MD — — REFOMD Bit 2 — OC3MD — Bit 1 — OC2MD I2C2MD Bit 0 ADC1MD OC1MD — — All Resets 0000 0000 0000 0000 PIC24FV32KA304 FAMILY CTMUMD HLVDMD — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. PIC24FV32KA304 FAMILY 4.2.5 SOFTWARE STACK 4.3 In addition to its use as a working register, the W15 register in PIC24F devices is also used as a Software Stack Pointer. The pointer always points to the first available free word and grows from lower to higher addresses. It predecrements for stack pops and post-increments for stack pushes, as shown in Figure 4-4. Note that for a PC push during any CALL instruction, the MSB of the PC is zero-extended before the push, ensuring that the MSB is always clear. Note: A PC push during exception processing will concatenate the SRL register to the MSB of the PC prior to the push. Interfacing Program and Data Memory Spaces The PIC24F architecture uses a 24-bit wide program space and 16-bit wide data space. The architecture is also a modified Harvard scheme, meaning that data can also be present in the program space. To use this data successfully, it must be accessed in a way that preserves the alignment of information in both spaces. Apart from the normal execution, the PIC24F architecture provides two methods by which the program space can be accessed during operation: • Using table instructions to access individual bytes or words anywhere in the program space • Remapping a portion of the program space into the data space, PSV Table instructions allow an application to read or write small areas of the program memory. This makes the method ideal for accessing data tables that need to be updated from time to time. It also allows access to all bytes of the program word. The remapping method allows an application to access a large block of data on a read-only basis, which is ideal for look-ups from a large table of static data. It can only access the least significant word (lsw) of the program word. The Stack Pointer Limit Value (SPLIM) register, associated with the Stack Pointer, sets an upper address boundary for the stack. SPLIM is uninitialized at Reset. As is the case for the Stack Pointer, SPLIM is forced to ‘0’ as all stack operations must be word-aligned. Whenever an EA is generated, using W15 as a source or destination pointer, the resulting address is compared with the value in SPLIM. If the contents of the Stack Pointer (W15) and the SPLIM register are equal, and a push operation is performed, a stack error trap will not occur. The stack error trap will occur on a subsequent push operation. Thus, for example, if it is desirable to cause a stack error trap when the stack grows beyond address, 0DF6, in RAM, initialize the SPLIM with the value, 0DF4. Similarly, a Stack Pointer underflow (stack error) trap is generated when the Stack Pointer address is found to be less than 0800h. This prevents the stack from interfering with the Special Function Register (SFR) space. Note: A write to the SPLIM register should not be immediately followed by an indirect read operation using W15. 4.3.1 ADDRESSING PROGRAM SPACE Since the address ranges for the data and program spaces are 16 and 24 bits, respectively, a method is needed to create a 23-bit or 24-bit program address from 16-bit data registers. The solution depends on the interface method to be used. For table operations, the 8-bit Table Memory Page Address register (TBLPAG) is used to define a 32K word region within the program space. This is concatenated with a 16-bit EA to arrive at a full 24-bit program space address. In this format, the Most Significant bit (MSb) of TBLPAG is used to determine if the operation occurs in the user memory (TBLPAG = 0) or the configuration memory (TBLPAG = 1). For remapping operations, the 8-bit Program Space Visibility Page Address register (PSVPAG) is used to define a 16K word page in the program space. When the MSb of the EA is ‘1’, PSVPAG is concatenated with the lower 15 bits of the EA to form a 23-bit program space address. Unlike the table operations, this limits remapping operations strictly to the user memory area. Table 4-27 and Figure 4-5 show how the program EA is created for table operations and remapping accesses from the data EA. Here, P bits refer to a program space word, whereas the D bits refer to a data space word. FIGURE 4-4: 0000h 15 CALL STACK FRAME 0 Stack Grows Towards Higher Address PC 000000000 PC W15 (before CALL) W15 (after CALL) POP : [--W15] PUSH : [W15++] DS39995B-page 53  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 4-27: PROGRAM SPACE ADDRESS CONSTRUCTION Access Space User User Configuration Program Space Visibility (Block Remap/Read) Note 1: 2: User 0 0 Program Space Address 0 TBLPAG 0xxx xxxx TBLPAG 1xxx xxxx PSVPAG(2) xxxx xxxx PC 0xx xxxx xxxx xxxx xxxx xxx0 Data EA xxxx xxxx xxxx xxxx Data EA xxxx xxxx xxxx xxxx Data EA(1) xxx xxxx xxxx xxxx 0 Access Type Instruction Access (Code Execution) TBLRD/TBLWT (Byte/Word Read/Write) Data EA is always ‘1’ in this case, but is not used in calculating the program space address. Bit 15 of the address is PSVPAG. PSVPAG can have only two values (‘00’ to access program memory and FF to access data EEPROM) on the PIC24FV32KA304 family. FIGURE 4-5: DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION Program Counter(1) 0 Program Counter 23 Bits 0 EA Table Operations(2) 1/0 TBLPAG 8 bits 16 bits 1/0 24 Bits Select 1 Program Space Visibility(1) (Remapping) 0 PSVPAG 8 bits EA 0 15 bits 23 bits User/Configuration Space Select Byte Select Note 1: 2: The LSb of program space addresses is always fixed as ‘0’ in order to maintain word alignment of data in the program and data spaces. Table operations are not required to be word-aligned. Table read operations are permitted in the configuration memory space.  2011 Microchip Technology Inc. DS39995B-page 54 PIC24FV32KA304 FAMILY 4.3.2 DATA ACCESS FROM PROGRAM MEMORY AND DATA EEPROM MEMORY USING TABLE INSTRUCTIONS Two table instructions are provided to move byte or word-sized (16-bit) data to and from program space. Both function as either byte or word operations. 1. TBLRDL (Table Read Low): In Word mode, it maps the lower word of the program space location (P) to a data address (D). In Byte mode, either the upper or lower byte of the lower program word is mapped to the lower byte of a data address. The upper byte is selected when byte select is ‘1’; the lower byte is selected when it is ‘0’. TBLRDH (Table Read High): In Word mode, it maps the entire upper word of a program address (P) to a data address. Note that D, the ‘phantom’ byte, will always be ‘0’. In Byte mode, it maps the upper or lower byte of the program word to D of the data address, as above. Note that the data will always be ‘0’ when the upper ‘phantom’ byte is selected (byte select = 1). The TBLRDL and TBLWTL instructions offer a direct method of reading or writing the lower word of any address within the program memory without going through data space. It also offers a direct method of reading or writing a word of any address within data EEPROM memory. The TBLRDH and TBLWTH instructions are the only method to read or write the upper 8 bits of a program space word as data. Note: The TBLRDH and TBLWTH instructions are not used while accessing data EEPROM memory. 2. The PC is incremented by two for each successive 24-bit program word. This allows program memory addresses to directly map to data space addresses. Program memory can thus be regarded as two 16-bit word-wide address spaces, residing side by side, each with the same address range. TBLRDL and TBLWTL access the space which contains the least significant data word, and TBLRDH and TBLWTH access the space which contains the upper data byte. DS39995B-page 55  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY In a similar fashion, two table instructions, TBLWTH and TBLWTL, are used to write individual bytes or words to a program space address. The details of their operation are explained in Section 5.0 “Flash Program Memory”. For all table operations, the area of program memory space to be accessed is determined by the Table Memory Page Address register (TBLPAG). TBLPAG covers the entire program memory space of the device, including user and configuration spaces. When TBLPAG = 0, the table page is located in the user memory space. When TBLPAG = 1, the page is located in configuration space. Note: Only table read operations will execute in the configuration memory space, and only then, in implemented areas, such as the Device ID. Table write operations are not allowed. FIGURE 4-6: ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS Program Space Data EA TBLPAG 00 23 15 0 000000h 00000000 00000000 00000000 002BFEh 00000000 23 16 8 0 ‘Phantom’ Byte TBLRDH.B (Wn = 0) TBLRDL.B (Wn = 1) TBLRDL.B (Wn = 0) TBLRDL.W 800000h The address for the table operation is determined by the data EA within the page defined by the TBLPAG register. Only read operations are provided; write operations are also valid in the user memory area.  2011 Microchip Technology Inc. DS39995B-page 56 PIC24FV32KA304 FAMILY 4.3.3 READING DATA FROM PROGRAM MEMORY USING PROGRAM SPACE VISIBILITY Although each data space address, 8000h and higher, maps directly into a corresponding program memory address (see Figure 4-7), only the lower 16 bits of the 24-bit program word are used to contain the data. The upper 8 bits of any program space location used as data should be programmed with ‘1111 1111’ or ‘0000 0000’ to force a NOP. This prevents possible issues should the area of code ever be accidentally executed. Note: PSV access is temporarily disabled during table reads/writes. The upper 32 Kbytes of data space may optionally be mapped into an 16K word page (in PIC24FV16KA3XX devices) and a 32K word page (in PIC24FV32KA3XX devices) of the program space. This provides transparent access of stored constant data from the data space without the need to use special instructions (i.e., TBLRDL/H). Program space access through the data space occurs if the MSb of the data space EA is ‘1’ and PSV is enabled by setting the PSV bit in the CPU Control (CORCON) register. The location of the program memory space to be mapped into the data space is determined by the Program Space Visibility Page Address (PSVPAG) register. This 8-bit register defines any one of 256 possible pages of 16K words in program space. In effect, PSVPAG functions as the upper 8 bits of the program memory address, with the 15 bits of the EA functioning as the lower bits. By incrementing the PC by 2 for each program memory word, the lower 15 bits of data space addresses directly map to the lower 15 bits in the corresponding program space addresses. Data reads from this area add an additional cycle to the instruction being executed, since two program memory fetches are required. For operations that use PSV and are executed outside a REPEAT loop, the MOV and MOV.D instructions will require one instruction cycle in addition to the specified execution time. All other instructions will require two instruction cycles in addition to the specified execution time. For operations that use PSV, which are executed inside a REPEAT loop, there will be some instances that require two instruction cycles in addition to the specified execution time of the instruction: • Execution in the first iteration • Execution in the last iteration • Execution prior to exiting the loop due to an interrupt • Execution upon re-entering the loop after an interrupt is serviced Any other iteration of the REPEAT loop will allow the instruction accessing data, using PSV, to execute in a single cycle. FIGURE 4-7: PROGRAM SPACE VISIBILITY OPERATION When CORCON = 1 and EA = 1: Program Space PSVPAG 00 23 15 0 000000h Data Space 0000h Data EA 002BFEh The data in the page designated by PSVPAG is mapped into the upper half of the data memory space.... 8000h PSV Area ...while the lower 15 bits of the EA specify an exact address within the PSV FFFFh area. This corresponds exactly to the same lower 15 bits of the actual program space address. 800000h  2011 Microchip Technology Inc. DS39995B-page 57 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 58  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 5.0 Note: FLASH PROGRAM MEMORY This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on Flash programming, refer to the “PIC24F Family Reference Manual”, Section 4. “Program Memory” (DS39715). Run Time Self Programming (RTSP) is accomplished using TBLRD (table read) and TBLWT (table write) instructions. With RTSP, the user may write program memory data in blocks of 32 instructions (96 bytes) at a time, and erase program memory in blocks of 32, 64 and 128 instructions (96,192 and 384 bytes) at a time. The NVMOP (NVMCON) bits decide the erase block size. The PIC24FV32KA304 of devices contains internal Flash program memory for storing and executing application code. The memory is readable, writable and erasable when operating with VDD over 1.8V. Flash memory can be programmed in three ways: • In-Circuit Serial Programming™ (ICSP™) • Run-Time Self Programming (RTSP) • Enhanced In-Circuit Serial Programming (Enhanced ICSP) ICSP allows a PIC24FV32KA304 device to be serially programmed while in the end application circuit. This is simply done with two lines for the programming clock and programming data (which are named PGECx and PGEDx, respectively), and three other lines for power (VDD), ground (VSS) and Master Clear/Program mode Entry Voltage (MCLR/VPP). This allows customers to manufacture boards with unprogrammed devices and then program the microcontroller just before shipping the product. This also allows the most recent firmware or custom firmware to be programmed. 5.1 Table Instructions and Flash Programming Regardless of the method used, Flash memory programming is done with the table read and write instructions. These allow direct read and write access to the program memory space from the data memory while the device is in normal operating mode. The 24-bit target address in the program memory is formed using the TBLPAG bits and the Effective Address (EA) from a W register, specified in the table instruction, as depicted in Figure 5-1. The TBLRDL and the TBLWTL instructions are used to read or write to bits of program memory. TBLRDL and TBLWTL can access program memory in both Word and Byte modes. The TBLRDH and TBLWTH instructions are used to read or write to bits of program memory. TBLRDH and TBLWTH can also access program memory in Word or Byte mode. FIGURE 5-1: ADDRESSING FOR TABLE REGISTERS 24 Bits Using Program Counter 0 Program Counter 0 Working Reg EA Using Table Instruction 1/0 TBLPAG Reg 8 Bits 16 Bits User/Configuration Space Select 24-Bit EA Byte Select  2011 Microchip Technology Inc. DS39995B-page 59 PIC24FV32KA304 FAMILY 5.2 RTSP Operation 5.3 The PIC24F Flash program memory array is organized into rows of 32 instructions or 96 bytes. RTSP allows the user to erase blocks of 1 row, 2 rows and 4 rows (32, 64 and 128 instructions) at a time and to program one row at a time. It is also possible to program single words. The 1-row (96 bytes), 2-row (192 bytes) and 4-row (384 bytes) erase blocks and single row write block (96 bytes) are edge-aligned, from the beginning of program memory. When data is written to program memory using TBLWT instructions, the data is not written directly to memory. Instead, data written using table writes is stored in holding latches until the programming sequence is executed. Any number of TBLWT instructions can be executed and a write will be successfully performed. However, 32 TBLWT instructions are required to write the full row of memory. The basic sequence for RTSP programming is to set up a Table Pointer, then do a series of TBLWT instructions to load the buffers. Programming is performed by setting the control bits in the NVMCON register. Data can be loaded in any order and the holding registers can be written to multiple times before performing a write operation. Subsequent writes, however, will wipe out any previous writes. Note: Writing to a location multiple times without erasing it is not recommended. Enhanced In-Circuit Serial Programming Enhanced ICSP uses an on-board bootloader, known as the program executive, to manage the programming process. Using an SPI data frame format, the program executive can erase, program and verify program memory. For more information on Enhanced ICSP, see the device programming specification. 5.4 Control Registers There are two SFRs used to read and write the program Flash memory: NVMCON and NVMKEY. The NVMCON register (Register 5-1) controls the blocks that need to be erased, which memory type is to be programmed and when the programming cycle starts. NVMKEY is a write-only register that is used for write protection. To start a programming or erase sequence, the user must consecutively write 55h and AAh to the NVMKEY register. For more information, refer to Section 5.5 “Programming Operations”. 5.5 Programming Operations A complete programming sequence is necessary for programming or erasing the internal Flash in RTSP mode. During a programming or erase operation, the processor stalls (waits) until the operation is finished. Setting the WR bit (NVMCON) starts the operation and the WR bit is automatically cleared when the operation is finished. All of the table write operations are single-word writes (two instruction cycles), because only the buffers are written. A programming cycle is required for programming each row. DS39995B-page 60  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 5-1: R/SO-0, HC WR bit 15 U-0 — bit 7 Legend: -n = Value at POR ‘0’ = Bit is cleared bit 15 SO = Settable Only bit ‘1’ = Bit is set x = Bit is unknown HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ R/W-0 ERASE R/W-0 NVMOP5 (1) NVMCON: FLASH MEMORY CONTROL REGISTER R/W-0 WRERR R/W-0 PGMONLY(4) U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 NVMOP4 (1) R/W-0 WREN R/W-0 NVMOP3 (1) R/W-0 NVMOP2 (1) R/W-0 NVMOP1 (1) R/W-0 NVMOP0(1) bit 0 WR: Write Control bit 1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is cleared by hardware once the operation is complete. 0 = Program or erase operation is complete and inactive WREN: Write Enable bit 1 = Enable Flash program/erase operations 0 = Inhibit Flash program/erase operations WRERR: Write Sequence Error Flag bit 1 = An improper program or erase sequence attempt or termination has occurred (bit is set automatically on any set attempt of the WR bit) 0 = The program or erase operation completed normally PGMONLY: Program Only Enable bit(4) Unimplemented: Read as ‘0’ ERASE: Erase/Program Enable bit 1 = Perform the erase operation specified by NVMOP on the next WR command 0 = Perform the program operation specified by NVMOP on the next WR command NVMOP: Programming Operation Command Byte bits(1) Erase Operations (when ERASE bit is ‘1’): 1010xx = Erase entire boot block (including code-protected boot block)(2) 1001xx = Erase entire memory (including boot block, configuration block, general block)(2) 011010 = Erase 4 rows of Flash memory(3) 011001 = Erase 2 rows of Flash memory(3) 011000 = Erase 1 row of Flash memory(3) 0101xx = Erase entire configuration block (except code protection bits) 0100xx = Erase entire data EEPROM(4) 0011xx = Erase entire general memory block programming operations 0001xx = Write 1 row of Flash memory (when ERASE bit is ‘0’)(3) All other combinations of NVMOP are no operation. Available in ICSP™ mode only. Refer to device programming specification. The address in the Table Pointer decides which rows will be erased. This bit is used only while accessing data EEPROM. bit 14 bit 13 bit 12 bit 11-7 bit 6 bit 5-0 Note 1: 2: 3: 4:  2011 Microchip Technology Inc. DS39995B-page 61 PIC24FV32KA304 FAMILY 5.5.1 PROGRAMMING ALGORITHM FOR FLASH PROGRAM MEMORY 4. 5. The user can program one row of Flash program memory at a time by erasing the programmable row. The general process is as follows: 1. 2. 3. Read a row of program memory (32 instructions) and store in data RAM. Update the program data in RAM with the desired new data. Erase a row (see Example 5-1): a) Set the NVMOP bits (NVMCON) to ‘011000’ to configure for row erase. Set the ERASE (NVMCON) and WREN (NVMCON) bits. b) Write the starting address of the block to be erased into the TBLPAG and W registers. c) Write 55h to NVMKEY. d) Write AAh to NVMKEY. e) Set the WR bit (NVMCON). The erase cycle begins and the CPU stalls for the duration of the erase cycle. When the erase is done, the WR bit is cleared automatically. Write the first 32 instructions from data RAM into the program memory buffers (see Example 5-1). Write the program block to Flash memory: a) Set the NVMOP bits to ‘011000’ to configure for row programming. Clear the ERASE bit and set the WREN bit. b) Write 55h to NVMKEY. c) Write AAh to NVMKEY. d) Set the WR bit. The programming cycle begins and the CPU stalls for the duration of the write cycle. When the write to Flash memory is done, the WR bit is cleared automatically. For protection against accidental operations, the write initiate sequence for NVMKEY must be used to allow any erase or program operation to proceed. After the programming command has been executed, the user must wait for the programming time until programming is complete. The two instructions following the start of the programming sequence should be NOPs, as shown in Example 5-5. EXAMPLE 5-1: ERASING A PROGRAM MEMORY ROW – ASSEMBLY LANGUAGE CODE ; ; Initialize NVMCON ; ; ; ; ; ; Set up NVMCON for row erase operation MOV #0x4058, W0 MOV W0, NVMCON ; Init pointer to row to be ERASED MOV #tblpage(PROG_ADDR), W0 MOV W0, TBLPAG MOV #tbloffset(PROG_ADDR), W0 TBLWTL W0, [W0] DISI #5 MOV MOV MOV MOV BSET NOP NOP #0x55, W0 W0, NVMKEY #0xAA, W1 W1, NVMKEY NVMCON, #WR Initialize PM Page Boundary SFR Initialize in-page EA[15:0] pointer Set base address of erase block Block all interrupts for next 5 instructions Write the 55 key Write the AA key Start the erase sequence Insert two NOPs after the erase command is asserted ; ; ; ; ; ; DS39995B-page 62  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY EXAMPLE 5-2: ERASING A PROGRAM MEMORY ROW – ‘C’ LANGUAGE CODE // C example using MPLAB C30 int __attribute__ ((space(auto_psv))) progAddr = &progAddr;// Global variable located in Pgm Memory unsigned int offset; //Set up pointer to the first memory location to be written TBLPAG = __builtin_tblpage(&progAddr); offset = &progAddr & 0xFFFF; __builtin_tblwtl(offset, 0x0000); NVMCON = 0x4058; asm("DISI #5"); __builtin_write_NVM(); // Initialize PM Page Boundary SFR // Initialize lower word of address // Set base address of erase block // with dummy latch write // Initialize NVMCON // // // // Block all interrupts for next 5 instructions C30 function to perform unlock sequence and set WR EXAMPLE 5-3: LOADING THE WRITE BUFFERS – ASSEMBLY LANGUAGE CODE ; Set up NVMCON for row programming operations MOV #0x4004, W0 ; MOV W0, NVMCON ; Initialize NVMCON ; Set up a pointer to the first program memory location to be written ; program memory selected, and writes enabled MOV #0x0000, W0 ; MOV W0, TBLPAG ; Initialize PM Page Boundary SFR MOV #0x6000, W0 ; An example program memory address ; Perform the TBLWT instructions to write the latches ; 0th_program_word MOV #LOW_WORD_0, W2 ; MOV #HIGH_BYTE_0, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 1st_program_word MOV #LOW_WORD_1, W2 ; MOV #HIGH_BYTE_1, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 2nd_program_word MOV #LOW_WORD_2, W2 ; MOV #HIGH_BYTE_2, W3 ; ; Write PM low word into program latch TBLWTL W2, [W0] ; Write PM high byte into program latch TBLWTH W3, [W0++] • • • ; 32nd_program_word MOV #LOW_WORD_31, W2 ; MOV #HIGH_BYTE_31, W3 ; ; Write PM low word into program latch TBLWTL W2, [W0] TBLWTH W3, [W0] ; Write PM high byte into program latch  2011 Microchip Technology Inc. DS39995B-page 63 PIC24FV32KA304 FAMILY EXAMPLE 5-4: LOADING THE WRITE BUFFERS – ‘C’ LANGUAGE CODE // C example using MPLAB C30 #define NUM_INSTRUCTION_PER_ROW 64 int __attribute__ ((space(auto_psv))) progAddr = &progAddr;// Global variable located in Pgm Memory unsigned int offset; unsigned int i; unsigned int progData[2*NUM_INSTRUCTION_PER_ROW]; // Buffer of data to write //Set up NVMCON for row programming NVMCON = 0x4001; // Initialize NVMCON //Set up pointer to the first memory location to be written TBLPAG = __builtin_tblpage(&progAddr); // Initialize PM Page Boundary SFR offset = &progAddr & 0xFFFF; // Initialize lower word of address //Perform TBLWT instructions to write necessary number of latches for(i=0; i < 2*NUM_INSTRUCTION_PER_ROW; i++) { __builtin_tblwtl(offset, progData[i++]); // Write to address low word __builtin_tblwth(offset, progData[i]); // Write to upper byte offset = offset + 2; // Increment address } EXAMPLE 5-5: DISI MOV MOV MOV MOV BSET NOP NOP BTSC BRA #5 INITIATING A PROGRAMMING SEQUENCE – ASSEMBLY LANGUAGE CODE ; Block all interrupts for next 5 instructions ; ; ; ; ; ; ; ; Write the 55 key Write the AA key Start the erase sequence 2 NOPs required after setting WR Wait for the sequence to be completed #0x55, W0 W0, NVMKEY #0xAA, W1 W1, NVMKEY NVMCON, #WR NVMCON, #15 $-2 EXAMPLE 5-6: INITIATING A PROGRAMMING SEQUENCE – ‘C’ LANGUAGE CODE // C example using MPLAB C30 asm("DISI #5"); __builtin_write_NVM(); // Block all interrupts for next 5 instructions // Perform unlock sequence and set WR DS39995B-page 64  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY EXAMPLE 5-7: ; Setup MOV MOV MOV MOV MOV TBLWTL TBLWTH ; Setup MOV MOV DISI MOV MOV MOV MOV BSET PROGRAMMING A SINGLE WORD OF FLASH PROGRAM MEMORY a pointer to data Program Memory #tblpage(PROG_ADDR), W0 ; W0, TBLPAG ;Initialize PM Page Boundary SFR #tbloffset(PROG_ADDR), W0 ;Initialize a register with program memory address #LOW_WORD_N, W2 ; #HIGH_BYTE_N, W3 ; W2, [W0] ; Write PM low word into program latch W3, [W0++] ; Write PM high byte into program latch NVMCON for programming one word to data Program Memory #0x4003, W0 ; W0, NVMCON ; Set NVMOP bits to 0011 #5 ; Disable interrupts while the KEY sequence is written #0x55, W0 ; Write the key sequence W0, NVMKEY #0xAA, W0 W0, NVMKEY NVMCON, #WR ; Start the write cycle  2011 Microchip Technology Inc. DS39995B-page 65 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 66  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 6.0 Note: DATA EEPROM MEMORY This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on Data EEPROM, refer to the “PIC24F Family Reference Manual”, S ection 5. “Data EEPROM” (DS39720). 6.1 NVMCON Register The NVMCON register (Register 6-1) is also the primary control register for data EEPROM program/erase operations. The upper byte contains the control bits used to start the program or erase cycle, and the flag bit to indicate if the operation was successfully performed. The lower byte of NVMCOM configures the type of NVM operation that will be performed. The data EEPROM memory is a Nonvolatile Memory (NVM), separate from the program and volatile data RAM. Data EEPROM memory is based on the same Flash technology as program memory, and is optimized for both long retention and a higher number of erase/write cycles. The data EEPROM is mapped to the top of the user program memory space, with the top address at program memory address, 7FFE00h to 7FFFFFh. The size of the data EEPROM is 256 words in PIC24FV32KA304 devices. The data EEPROM is organized as 16-bit wide memory. Each word is directly addressable, and is readable and writable during normal operation over the entire VDD range. Unlike the Flash program memory, normal program execution is not stopped during a data EEPROM program or erase operation. The data EEPROM programming operations are controlled using the three NVM Control registers: • NVMCON: Nonvolatile Memory Control Register • NVMKEY: Nonvolatile Memory Key Register • NVMADR: Nonvolatile Memory Address Register 6.2 NVMKEY Register The NVMKEY is a write-only register that is used to prevent accidental writes or erasures of data EEPROM locations. To start any programming or erase sequence, the following instructions must be executed first, in the exact order provided: 1. 2. Write 55h to NVMKEY. Write AAh to NVMKEY. After this sequence, a write will be allowed to the NVMCON register for one instruction cycle. In most cases, the user will simply need to set the WR bit in the NVMCON register to start the program or erase cycle. Interrupts should be disabled during the unlock sequence. The MPLAB® C30 C compiler provides a defined library procedure (builtin_write_NVM) to perform the unlock sequence. Example 6-1 illustrates how the unlock sequence can be performed with in-line assembly. EXAMPLE 6-1: DATA EEPROM UNLOCK SEQUENCE //Disable Interrupts For 5 instructions asm volatile("disi #5"); //Issue Unlock Sequence asm volatile("mov #0x55, W0 \n" "mov W0, NVMKEY \n" "mov #0xAA, W1 \n" "mov W1, NVMKEY \n"); // Perform Write/Erase operations asm volatile ("bset NVMCON, #WR \n" "nop \n" "nop \n");  2011 Microchip Technology Inc. DS39995B-page 67 PIC24FV32KA304 FAMILY REGISTER 6-1: R/S-0, HC WR bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 HC = Hardware Clearable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ S = Settable bit ‘0’ = Bit is cleared x = Bit is unknown R/W-0 ERASE R/W-0 NVMOP5 R/W-0 NVMOP4 R/W-0 NVMOP3 R/W-0 NVMOP2 R/W-0 NVMOP1 NVMCON: NONVOLATILE MEMORY CONTROL REGISTER R/W-0 WREN R/W-0 WRERR R/W-0 PGMONLY U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 NVMOP0 bit 0 WR: Write Control bit (program or erase) 1 = Initiates a data EEPROM erase or write cycle (can be set but not cleared in software) 0 = Write cycle is complete (cleared automatically by hardware) WREN: Write Enable bit (erase or program) 1 = Enable an erase or program operation 0 = No operation allowed (device clears this bit on completion of the write/erase operation) WRERR: Flash Error Flag bit 1 = A write operation is prematurely terminated (any MCLR or WDT Reset during programming operation) 0 = The write operation completed successfully PGMONLY: Program Only Enable bit 1 = Write operation is executed without erasing target address(es) first 0 = Automatic erase-before-write. Write operations are preceded automatically by an erase of target address(es). Unimplemented: Read as ‘0’ ERASE: Erase Operation Select bit 1 = Perform an erase operation when WR is set 0 = Perform a write operation when WR is set NVMOP: Programming Operation Command Byte bits Erase Operations (when ERASE bit is ‘1’): 011010 = Erase 8 words 011001 = Erase 4 words 011000 = Erase 1 word 0100xx = Erase entire data EEPROM Programming Operations (when ERASE bit is ‘0’): 001xx = Write 1 word bit 14 bit 13 bit 12 bit 11-7 bit 6 bit 5-0 DS39995B-page 68  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 6.3 NVM Address Register As with Flash program memory, the NVM Address Registers, NVMADRU and NVMADR, form the 24-bit Effective Address (EA) of the selected row or word for data EEPROM operations. The NVMADRU register is used to hold the upper 8 bits of the EA, while the NVMADR register is used to hold the lower 16 bits of the EA. These registers are not mapped into the Special Function Register (SFR) space; instead, they directly capture the EA of the last table write instruction that has been executed and selects the data EEPROM row to erase. Figure 6-1 depicts the program memory EA that is formed for programming and erase operations. Like program memory operations, the Least Significant bit (LSb) of NVMADR is restricted to even addresses. This is because any given address in the data EEPROM space consists of only the lower word of the program memory width; the upper word, including the uppermost “phantom byte”, are unavailable. This means that the LSb of a data EEPROM address will always be ‘0’. Similarly, the Most Significant bit (MSb) of NVMADRU is always ‘0’, since all addresses lie in the user program space. FIGURE 6-1: DATA EEPROM ADDRESSING WITH TBLPAG AND NVM ADDRESS REGISTERS 24-Bit PM Address 7Fh 0 TBLPAG xxxxh W Register EA 0 NVMADRU NVMADR 6.4 Data EEPROM Operations The EEPROM block is accessed using table read and write operations similar to those used for program memory. The TBLWTH and TBLRDH instructions are not required for data EEPROM operations since the memory is only 16 bits wide (data on the lower address is valid only). The following programming operations can be performed on the data EEPROM: • • • • Erase one, four or eight words Bulk erase the entire data EEPROM Write one word Read one word Note 1: Unexpected results will be obtained if the user attempts to read the EEPROM while a programming or erase operation is underway. 2: The C30 C compiler includes library procedures to automatically perform the table read and table write operations, manage the Table Pointer and write buffers, and unlock and initiate memory write sequences. This eliminates the need to create assembler macros or time critical routines in C for each application. The library procedures are used in the code examples detailed in the following sections. General descriptions of each process are provided for users who are not using the C30 compiler libraries.  2011 Microchip Technology Inc. DS39995B-page 69 PIC24FV32KA304 FAMILY 6.4.1 ERASE DATA EEPROM The data EEPROM can be fully erased, or can be partially erased, at three different sizes: one word, four words or eight words. The bits, NVMOP (NVMCON), decide the number of words to be erased. To erase partially from the data EEPROM, the following sequence must be followed: 1. 2. 3. 4. 5. 6. Configure NVMCON to erase the required number of words: one, four or eight. Load TBLPAG and WREG with the EEPROM address to be erased. Clear NVMIF status bit and enable the NVM interrupt (optional). Write the key sequence to NVMKEY. Set the WR bit to begin erase cycle. Either poll the WR bit or wait for the NVM interrupt (NVMIF set). A typical erase sequence is provided in Example 6-2. This example shows how to do a one-word erase. Similarly, a four-word erase and an eight-word erase can be done. This example uses C library procedures to manage the Table Pointer (builtin_tblpage and builtin_tbloffset) and the Erase Page Pointer (builtin_tblwtl). The memory unlock sequence (builtin_write_NVM) also sets the WR bit to initiate the operation and returns control when complete. EXAMPLE 6-2: SINGLE-WORD ERASE int __attribute__ ((space(eedata))) eeData = 0x1234; // Global variable located in EEPROM unsigned int offset; // Set up NVMCON to erase one word of data EEPROM NVMCON = 0x4058; // Set up a pointer to the EEPROM location to be erased TBLPAG = __builtin_tblpage(&eeData); // Initialize EE Data page pointer offset = __builtin_tbloffset(&eeData); // Initizlize lower word of address __builtin_tblwtl(offset, 0); // Write EEPROM data to write latch asm volatile ("disi #5"); __builtin_write_NVM(); while(NVMCONbits.WR=1); // // // // Disable Interrupts For 5 Instructions Issue Unlock Sequence & Start Write Cycle Optional: Poll WR bit to wait for write sequence to complete DS39995B-page 70  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 6.4.1.1 Data EEPROM Bulk Erase 6.4.2 SINGLE-WORD WRITE To erase the entire data EEPROM (bulk erase), the address registers do not need to be configured because this operation affects the entire data EEPROM. The following sequence helps in performing a bulk erase: 1. 2. 3. 4. 5. Configure NVMCON to Bulk Erase mode. Clear NVMIF status bit and enable NVM interrupt (optional). Write the key sequence to NVMKEY. Set the WR bit to begin erase cycle. Either poll the WR bit or wait for the NVM interrupt (NVMIF set). To write a single word in the data EEPROM, the following sequence must be followed: 1. Erase one data EEPROM word (as mentioned in the previous section) if PGMONLY bit (NVMCON) is set to ‘1’. Write the data word into the data EEPROM latch. Program the data word into the EEPROM: - Configure the NVMCON register to program one EEPROM word (NVMCON = 0001xx). - Clear NVMIF status bit and enable NVM interrupt (optional). - Write the key sequence to NVMKEY. - Set the WR bit to begin erase cycle. - Either poll the WR bit or wait for the NVM interrupt (NVMIF set). - To get cleared, wait until NVMIF is set. 2. 3. A typical bulk erase sequence is provided in Example 6-3. A typical single-word write sequence is provided in Example 6-4. EXAMPLE 6-3: DATA EEPROM BULK ERASE // Set up NVMCON to bulk erase the data EEPROM NVMCON = 0x4050; // Disable Interrupts For 5 Instructions asm volatile ("disi #5"); // Issue Unlock Sequence and Start Erase Cycle __builtin_write_NVM(); EXAMPLE 6-4: SINGLE-WORD WRITE TO DATA EEPROM // Global variable located in EEPROM // New data to write to EEPROM int __attribute__ ((space(eedata))) eeData = 0x1234; int newData; unsigned int offset; // Set up NVMCON to erase one word of data EEPROM NVMCON = 0x4004; // Set up a pointer to the EEPROM location to be erased TBLPAG = __builtin_tblpage(&eeData); // Initialize EE Data page pointer offset = __builtin_tbloffset(&eeData); // Initizlize lower word of address __builtin_tblwtl(offset, newData); // Write EEPROM data to write latch asm volatile ("disi #5"); __builtin_write_NVM(); while(NVMCONbits.WR=1); // // // // Disable Interrupts For 5 Instructions Issue Unlock Sequence & Start Write Cycle Optional: Poll WR bit to wait for write sequence to complete  2011 Microchip Technology Inc. DS39995B-page 71 PIC24FV32KA304 FAMILY 6.4.3 READING THE DATA EEPROM To read a word from data EEPROM, the table read instruction is used. Since the EEPROM array is only 16 bits wide, only the TBLRDL instruction is needed. The read operation is performed by loading TBLPAG and WREG with the address of the EEPROM location followed by a TBLRDL instruction. A typical read sequence, using the Table Pointer management (builtin_tblpage a nd builtin_tbloffset) and table read (builtin_tblrdl) procedures from the C30 compiler library, is provided in Example 6-5. Program Space Visibility (PSV) can also be used to read locations in the data EEPROM. EXAMPLE 6-5: READING THE DATA EEPROM USING THE TBLRD COMMAND // Global variable located in EEPROM int __attribute__ ((space(eedata))) eeData = 0x1234; int data; // Data read from EEPROM unsigned int offset; // Set TBLPAG offset data = up a pointer to the EEPROM location to be erased = __builtin_tblpage(&eeData); // Initialize EE Data page pointer = __builtin_tbloffset(&eeData); // Initizlize lower word of address __builtin_tblrdl(offset); // Write EEPROM data to write latch DS39995B-page 72  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 7.0 Note: RESETS This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on Resets, refer to the “PIC24F Family Reference Manual”, Section 40. “Reset with Programmable Brown-out Reset” (DS39728). Any active source of Reset will make the SYSRST signal active. Many registers associated with the CPU and peripherals are forced to a known Reset state. Most registers are unaffected by a Reset; their status is unknown on Power-on Reset (POR) and unchanged by all other Resets. Note: Refer to the specific peripheral or CPU section of this manual for register Reset states. The Reset module combines all Reset sources and controls the device Master Reset Signal, SYSRST. The following is a list of device Reset sources: • • • • • • • • • POR: Power-on Reset MCLR: Pin Reset SWR: RESET Instruction WDTR: Watchdog Timer Reset BOR: Brown-out Reset Low-Power BOR/Deep Sleep BOR TRAPR: Trap Conflict Reset IOPUWR: Illegal Opcode Reset UWR: Uninitialized W Register Reset All types of device Reset will set a corresponding status bit in the RCON register to indicate the type of Reset (see Register 7-1). A POR will clear all bits except for the BOR and POR bits (RCON) which are set. The user may set or clear any bit at any time during code execution. The RCON bits only serve as status bits. Setting a particular Reset status bit in software will not cause a device Reset to occur. The RCON register also has other bits associated with the Watchdog Timer (WDT) and device power-saving states. The function of these bits is discussed in other sections of this manual. Note: The status bits in the RCON register should be cleared after they are read so that the next RCON register value after a device Reset will be meaningful. A simplified block diagram of the Reset module is shown in Figure 7-1. FIGURE 7-1: RESET SYSTEM BLOCK DIAGRAM RESET Instruction Glitch Filter MCLR WDT Module Sleep or Idle VDD Rise Detect BOREN 00 01 10 11 VDD Brown-out Reset Enable Voltage Regulator (PIC24FV32KA3XX only) Configuration Mismatch Trap Conflict Illegal Opcode Uninitialized W Register POR SYSRST 0 RCON SLEEP 1 BOR  2011 Microchip Technology Inc. DS39995B-page 73 PIC24FV32KA304 FAMILY REGISTER 7-1: R/W-0, HS TRAPR bit 15 R/W-0, HS EXTR bit 7 RCON: RESET CONTROL REGISTER(1) R/W-0 SBOREN R/W-0 LVREN(3) U-0 — R/C-0, HS DPSLP R/W-0 CM R/W-0 PMSLP bit 8 R/W-1, HS POR bit 0 R/W-0, HS IOPUWR R/W-0, HS SWR R/W-0, HS SWDTEN(2) R/W-0, HS WDTO R/W-0, HS SLEEP R/W-0, HS IDLE R/W-1, HS BOR Legend: R = Readable bit -n = Value at POR bit 15 C = Clearable bit W = Writable bit ‘1’ = Bit is set HS = Hardware Settable bit U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 bit 7 bit 6 bit 5 TRAPR: Trap Reset Flag bit 1 = A Trap Conflict Reset has occurred 0 = A Trap Conflict Reset has not occurred IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit 1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an Address Pointer caused a Reset 0 = An illegal opcode or uninitialized W Reset has not occurred SBOREN: Software Enable/Disable of BOR bit 1 = BOR is turned on in software 0 = BOR is turned off in software LVREN: Low-Voltage Sleep Mode(3) 1 = Regulated voltage supply provided solely by the Low-Voltage Regulator (LVREG) during Sleep 0 = Regulated voltage supply provided by the main voltage regulator (HVREG) during Sleep(3) Unimplemented: Read as ‘0’ DPSLP: Deep Sleep Mode Flag bit 1 = Deep Sleep has occurred 0 = Deep Sleep has not occurred CM: Configuration Word Mismatch Reset Flag bit 1 = A Configuration Word Mismatch Reset has occurred 0 = A Configuration Word Mismatch Reset has not occurred PMSLP: Program Memory Power During Sleep bit 1 = Program memory bias voltage remains powered during Sleep 0 = Program memory bias voltage is powered down during Sleep and voltage regulator enters Standby mode EXTR: External Reset (MCLR) Pin bit 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred SWR: Software Reset (Instruction) Flag bit 1 = A RESET instruction has been executed 0 = A RESET instruction has not been executed SWDTEN: Software Enable/Disable of WDT bit(2) 1 = WDT is enabled 0 = WDT is disabled All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not cause a device Reset. If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the SWDTEN bit setting. On PIC24FV32KA3xx parts only, not used on PIC24F32KA3XX. Note 1: 2: 3: DS39995B-page 74  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 7-1: bit 4 RCON: RESET CONTROL REGISTER(1) (CONTINUED) bit 3 bit 2 bit 1 bit 0 WDTO: Watchdog Timer Time-out Flag bit 1 = WDT time-out has occurred 0 = WDT time-out has not occurred SLEEP: Wake-up from Sleep Flag bit 1 = Device has been in Sleep mode 0 = Device has not been in Sleep mode IDLE: Wake-up from Idle Flag bit 1 = Device has been in Idle mode 0 = Device has not been in Idle mode BOR: Brown-out Reset Flag bit 1 = A Brown-out Reset has occurred (the BOR is also set after a POR) 0 = A Brown-out Reset has not occurred POR: Power-on Reset Flag bit 1 = A Power-up Reset has occurred 0 = A Power-up Reset has not occurred All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not cause a device Reset. If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the SWDTEN bit setting. On PIC24FV32KA3xx parts only, not used on PIC24F32KA3XX. Note 1: 2: 3: TABLE 7-1: RESET FLAG BIT OPERATION Setting Event Trap Conflict Event Illegal Opcode or Uninitialized W Register Access Configuration Mismatch Reset MCLR Reset RESET Instruction WDT Time-out PWRSAV #SLEEP Instruction PWRSAV #IDLE Instruction POR, BOR POR PWRSAV #SLEEP instruction with DSCON set Clearing Event POR POR POR POR POR PWRSAV Instruction, POR POR POR — — POR Flag Bit TRAPR (RCON) IOPUWR (RCON) CM (RCON) EXTR (RCON) SWR (RCON) WDTO (RCON) SLEEP (RCON) IDLE (RCON) BOR (RCON) POR (RCON) DPSLP (RCON) Note: All Reset flag bits may be set or cleared by the user software. 7.1 Clock Source Selection at Reset TABLE 7-2: If clock switching is enabled, the system clock source at device Reset is chosen, as shown in Table 7-2. If clock switching is disabled, the system clock source is always selected according to the oscillator Configuration bits. For more information, see Section 9.0 “Oscillator Configuration”. OSCILLATOR SELECTION vs. TYPE OF RESET (CLOCK SWITCHING ENABLED) Clock Source Determinant FNOSC Configuration bits (FNOSC) COSC Control bits (OSCCON) Reset Type POR BOR MCLR WDTO SWR  2011 Microchip Technology Inc. DS39995B-page 75 PIC24FV32KA304 FAMILY 7.2 Device Reset Times The Reset times for various types of device Reset are summarized in Table 7-3. Note that the system Reset signal, SYSRST, is released after the POR and PWRT delay times expire. The time at which the device actually begins to execute code will also depend on the system oscillator delays, which include the Oscillator Start-up Timer (OST) and the PLL lock time. The OST and PLL lock times occur in parallel with the applicable SYSRST delay times. The FSCM delay determines the time at which the FSCM begins to monitor the system clock source after the SYSRST signal is released. TABLE 7-3: Reset Type POR(6) RESET DELAY TIMES FOR VARIOUS DEVICE RESETS Clock Source EC FRC, FRCDIV LPRC ECPLL FRCPLL XT, HS, SOSC XTPLL, HSPLL SYSRST Delay TPOR + TPWRT TPOR + TPWRT TPOR + TPWRT TPOR + TPWRT TPOR + TPWRT TPOR+ TPWRT TPOR + TPWRT TPWRT TPWRT TPWRT TPWRT TPWRT TPWRT TPWRT — System Clock Delay — TFRC TLPRC TLOCK TFRC + TLOCK TOST TOST + TLOCK — TFRC TLPRC TLOCK TFRC + TLOCK TOST TFRC + TLOCK — 1, 2 1, 2, 3 1, 2, 3 1, 2, 4 1, 2, 3, 4 1, 2, 5 1, 2, 4, 5 2 2, 3 2, 3 2, 4 2, 3, 4 2, 5 2, 3, 4 None Notes BOR EC FRC, FRCDIV LPRC ECPLL FRCPLL XT, HS, SOSC XTPLL, HSPLL All Others Note 1: 2: 3: 4: 5: 6: Any Clock TPOR = Power-on Reset delay. TPWRT = 64 ms nominal if the Power-up Timer is enabled; otherwise, it is zero. TFRC and TLPRC = RC Oscillator start-up times. TLOCK = PLL lock time. TOST = Oscillator Start-up Timer (OST). A 10-bit counter waits 1024 oscillator periods before releasing oscillator clock to the system. If Two-Speed Start-up is enabled, regardless of the primary oscillator selected, the device starts with FRC, and in such cases, FRC start-up time is valid. For detailed operating frequency and timing specifications, see Section 29.0 “Electrical Characteristics”. Note: DS39995B-page 76  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 7.2.1 POR AND LONG OSCILLATOR START-UP TIMES 7.5 Brown-out Reset (BOR) The oscillator start-up circuitry and its associated delay timers are not linked to the device Reset delays that occur at power-up. Some crystal circuits (especially low-frequency crystals) will have a relatively long start-up time. Therefore, one or more of the following conditions is possible after SYSRST is released: • The oscillator circuit has not begun to oscillate. • The Oscillator Start-up Timer (OST) has not expired (if a crystal oscillator is used). • The PLL has not achieved a lock (if PLL is used). The device will not begin to execute code until a valid clock source has been released to the system. Therefore, the oscillator and PLL start-up delays must be considered when the Reset delay time must be known. The PIC24FV32KA304 family devices implement a BOR circuit, which provides the user several configuration and power-saving options. The BOR is controlled by the BORV and BOREN Configuration bits (FPOR). There are a total of four BOR configurations, which are provided in Table 7-3. The BOR threshold is set by the BORV bits. If BOR is enabled (any values of BOREN, except ‘00’), any drop of VDD below the set threshold point will reset the device. The chip will remain in BOR until VDD rises above the threshold. If the Power-up Timer is enabled, it will be invoked after VDD rises above the threshold; then, it will keep the chip in Reset for an additional time delay, TPWRT, if VDD drops below the threshold while the power-up timer is running. The chip goes back into a BOR and the Power-up Timer will be initialized. Once VDD rises above the threshold, the Power-up Timer will execute the additional time delay. BOR and the Power-up Timer (PWRT) are independently configured. Enabling the BOR Reset does not automatically enable the PWRT. 7.2.2 FAIL-SAFE CLOCK MONITOR (FSCM) AND DEVICE RESETS If the FSCM is enabled, it will begin to monitor the system clock source when SYSRST is released. If a valid clock source is not available at this time, the device will automatically switch to the FRC Oscillator and the user can switch to the desired crystal oscillator in the Trap Service Routine (TSR). 7.5.1 SOFTWARE ENABLED BOR 7.3 Special Function Register Reset States Most of the Special Function Registers (SFRs) associated with the PIC24F CPU and peripherals are reset to a particular value at a device Reset. The SFRs are grouped by their peripheral or CPU function and their Reset values are specified in each section of this manual. The Reset value for each SFR does not depend on the type of Reset with the exception of four registers. The Reset value for the Reset Control register, RCON, will depend on the type of device Reset. The Reset value for the Oscillator Control register, OSCCON, will depend on the type of Reset and the programmed values of the FNOSC bits in the Flash Configuration Word (FOSCSEL); see Table 7-2. The RCFGCAL and NVMCON registers are only affected by a POR. When BOREN = 01, the BOR can be enabled or disabled by the user in software. This is done with the control bit, SBOREN (RCON). Setting SBOREN enables the BOR to function as previously described. Clearing the SBOREN disables the BOR entirely. The SBOREN bit operates only in this mode; otherwise, it is read as ‘0’. Placing BOR under software control gives the user the additional flexibility of tailoring the application to its environment without having to reprogram the device to change the BOR configuration. It also allows the user to tailor the incremental current that the BOR consumes. While the BOR current is typically very small, it may have some impact in low-power applications. Note: Even when the BOR is under software control, the BOR Reset voltage level is still set by the BORV Configuration bits. It can not be changed in software. 7.4 Deep Sleep BOR (DSBOR) Deep Sleep BOR is a very low-power BOR circuitry, used when the device is in Deep Sleep mode. Due to low current consumption, accuracy may vary. The DSBOR trip point is around 2.0V. DSBOR is enabled by configuring DSLPBOR (FDS) = 1. DSLPBOR will re-arm the POR to ensure the device will reset if VDD drops below the POR threshold.  2011 Microchip Technology Inc. DS39995B-page 77 PIC24FV32KA304 FAMILY 7.5.2 DETECTING BOR 7.5.3 DISABLING BOR IN SLEEP MODE When BOR is enabled, the BOR bit (RCON) is always reset to ‘1’ on any BOR or POR event. This makes it difficult to determine if a BOR event has occurred just by reading the state of BOR alone. A more reliable method is to simultaneously check the state of both POR and BOR. This assumes that the POR and BOR bits are reset to ‘0’ in the software immediately after any POR event. If the BOR bit is ‘1’ while POR is ‘0’, it can be reliably assumed that a BOR event has occurred. Note: Even when the device exits from Deep Sleep mode, both the POR and BOR are set. When BOREN = 10, BOR remains under hardware control and operates as previously described. However, whenever the device enters Sleep mode, BOR is automatically disabled. When the device returns to any other operating mode, BOR is automatically re-enabled. This mode allows for applications to recover from brown-out situations, while actively executing code when the device requires BOR protection the most. At the same time, it saves additional power in Sleep mode by eliminating the small incremental BOR current. Note: BOR levels differ depending on device type; PIC24FV32KA3XX devices are at different levels than those of PIC24F32KA3XX devices. See Section 29.0 “Electrical Characteristics” for BOR voltage levels. DS39995B-page 78  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 8.0 Note: INTERRUPT CONTROLLER This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the Interrupt Controller, refer to the “PIC24F Family Reference Manual”, Section 8. “Interrupts” (DS39707). 8.1.1 ALTERNATE INTERRUPT VECTOR TABLE (AIVT) The Alternate Interrupt Vector Table (AIVT) is located after the IVT, as shown in Figure 8-1. Access to the AIVT is provided by the ALTIVT control bit (INTCON2). If the ALTIVT bit is set, all interrupt and exception processes will use the alternate vectors instead of the default vectors. The alternate vectors are organized in the same manner as the default vectors. The AIVT supports emulation and debugging efforts by providing a means to switch between an application and a support environment without requiring the interrupt vectors to be reprogrammed. This feature also enables switching between applications for evaluation of different software algorithms at run-time. If the AIVT is not needed, the AIVT should be programmed with the same addresses used in the IVT. The PIC24F interrupt controller reduces the numerous peripheral interrupt request signals to a single interrupt request signal to the CPU. It has the following features: • Up to eight processor exceptions and software traps • Seven user-selectable priority levels • Interrupt Vector Table (IVT) with up to 118 vectors • Unique vector for each interrupt or exception source • Fixed priority within a specified user priority level • Alternate Interrupt Vector Table (AIVT) for debug support • Fixed interrupt entry and return latencies 8.2 Reset Sequence 8.1 Interrupt Vector (IVT) Table The IVT is shown in Figure 8-1. The IVT resides in the program memory, starting at location, 000004h. The IVT contains 126 vectors, consisting of eight non-maskable trap vectors, plus, up to 118 sources of interrupt. In general, each interrupt source has its own vector. Each interrupt vector contains a 24-bit wide address. The value programmed into each interrupt vector location is the starting address of the associated Interrupt Service Routine (ISR). Interrupt vectors are prioritized in terms of their natural priority; this is linked to their position in the vector table. All other things being equal, lower addresses have a higher natural priority. For example, the interrupt associated with vector 0 will take priority over interrupts at any other vector address. PIC24FV32KA304 family devices implement non-maskable traps and unique interrupts; these are summarized in Table 8-1 and Table 8-2. A device Reset is not a true exception, because the interrupt controller is not involved in the Reset process. The PIC24F devices clear their registers in response to a Reset, which forces the Program Counter (PC) to zero. The microcontroller then begins program execution at location, 000000h. The user programs a GOTO instruction at the Reset address, which redirects the program execution to the appropriate start-up routine. Note: Any unimplemented or unused vector locations in the IVT and AIVT should be programmed with the address of a default interrupt handler routine that contains a RESET instruction.  2011 Microchip Technology Inc. DS39995B-page 79 PIC24FV32KA304 FAMILY FIGURE 8-1: PIC24F INTERRUPT VECTOR TABLE Reset – GOTO Instruction Reset – GOTO Address Reserved Oscillator Fail Trap Vector Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 Interrupt Vector 1 — — — Interrupt Vector 52 Interrupt Vector 53 Interrupt Vector 54 — — — Interrupt Vector 116 Interrupt Vector 117 Reserved Reserved Reserved Oscillator Fail Trap Vector Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 Interrupt Vector 1 — — — Interrupt Vector 52 Interrupt Vector 53 Interrupt Vector 54 — — — Interrupt Vector 116 Interrupt Vector 117 Start of Code 000000h 000002h 000004h 000014h Decreasing Natural Order Priority 00007Ch 00007Eh 000080h Interrupt Vector Table (IVT)(1) 0000FCh 0000FEh 000100h 000102h 000114h Alternate Interrupt Vector Table (AIVT)(1) 00017Ch 00017Eh 000180h 0001FEh 000200h Note 1: See Table 8-2 for the interrupt vector list. DS39995B-page 80  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 8-1: 0 1 2 3 4 5 6 7 TRAP VECTOR DETAILS IVT Address 000004h 000006h 000008h 00000Ah 00000Ch 00000Eh 000010h 000012h AIVT Address 000104h 000106h 000108h 00010Ah 00010Ch 00010Eh 000110h 000112h Reserved Oscillator Failure Address Error Stack Error Math Error Reserved Reserved Reserved Trap Source Vector Number TABLE 8-2: IMPLEMENTED INTERRUPT VECTORS Vector Number IVT Address 13 18 67 77 0 20 29 17 16 50 49 1 5 37 19 72 15 2 6 25 62 9 10 32 33 3 7 8 27 28 65 11 12 66 30 31 80 00002Eh 000038h 00009Ah 0000AEh 000014h 00003Ch 00004Eh 000036h 000034h 000078h 000076h 000016h 00001Eh 00005Eh 00003Ah 0000A4h 000032h 000018h 000020h 000046h 000090h 000026h 000028h 000054h 000056h 00001Ah 000022h 000024h 00004Ah 00004Ch 000096h 00002Ah 00002Ch 000098h 000050h 000052h 0000B4h AIVT Address 00012Eh 000138h 00019Ah 0001AEh 000114h 00013Ch 00014Eh 000136h 000134h 000178h 000176h 000116h 00011Eh 00015Eh 00013Ah 0001A4h 000132h 000118h 000120h 000146h 000190h 000126h 000128h 000154h 000156h 00011Ah 000122h 000124h 00014Ah 00015Ch 000196h 00012Ah 00012Ch 000198h 000150h 000152h 0001B4h Interrupt Bit Locations Flag IFS0 IFS1 IFS4 IFS4 IFS0 IFS1 IFS1 IFS1 IFS1 IFS3 IFS3 IFS0 IFS0 IFS2 IFS1 IFS4 IFS0 IFS0 IFS0 IFS1 IFS3 IFS0 IFS0 IFS2 IFS2 IFS0 IFS0 IFS0 IFS1 IFS1 IFS4 IFS0 IFS0 IFS4 IFS1 IFS1 IFS5 Enable IEC0 IEC1 IEC4 IEC4 IEC0 IEC1 IEC1 IEC1 IEC1 IEC3 IEC3 IEC0 IEC0 IEC2 IEC1 IEC4 IEC0 IEC0 IEC0 IEC1 IEC3 IEC0 IEC0 IEC2 IEC2 IEC0 IEC0 IEC0 IEC1 IEC1 IEC4 IEC0 IEC0 IEC4 IEC1 IEC1 IEC5 Priority IPC3 IPC4 IPC16 IPC19 IPC0 IPC5 IPC7 IPC4 IPC4 IPC12 IPC12 IPC0 IPC1 IPC9 IPC4 IPC17 IPC3 IPC0 IPC1 IPC6 IPC15 IPC2 IPC2 IPC8 IPC8 IPC0 IPC1 IPC2 IPC6 IPC7 IPC16 IPC2 IPC3 IPC16 IPC7 IPC7 IPC20 Interrupt Source ADC1 Conversion Done Comparator Event CRC Generator CTMU External Interrupt 0 External Interrupt 1 External Interrupt 2 I2C1 Master Event I2C1 Slave Event I2C2 Master Event I2C2 Slave Event Input Capture 1 Input Capture 2 Input Capture 3 Input Change Notification HLVD (High/Low-Voltage Detect) NVM – NVM Write Complete Output Compare 1 Output Compare 2 Output Compare 3 Real-Time Clock/Calendar SPI1 Error SPI1 Event SPI2 Error SPI2 Event Timer1 Timer2 Timer3 Timer4 Timer5 UART1 Error UART1 Receiver UART1 Transmitter UART2 Error UART2 Receiver UART2 Transmitter Ultra Low-Power Wake-up  2011 Microchip Technology Inc. DS39995B-page 81 PIC24FV32KA304 FAMILY 8.3 Interrupt Control and Status Registers The INTTREG register contains the associated interrupt vector number and the new CPU interrupt priority level, which are latched into the Vector Number (VECNUM) and the Interrupt Level (ILR) bit fields in the INTTREG register. The new interrupt priority level is the priority of the pending interrupt. The interrupt sources are assigned to the IFSx, IECx and IPCx registers in the same sequence listed in Table 8-2. For example, the INT0 (External Interrupt 0) is depicted as having a vector number and a natural order priority of 0. The INT0IF status bit is found in IFS0, the INT0IE enable bit in IEC0 and the INT0IP priority bits are in the first position of IPC0 (IPC0). Although they are not specifically part of the interrupt control hardware, two of the CPU control registers contain bits that control interrupt functionality. The ALU STATUS register (SR) contains the IPL bits (SR). These indicate the current CPU interrupt priority level. The user may change the current CPU priority level by writing to the IPL bits. The CORCON register contains the IPL3 bit, which together with IPL, also indicates the current CPU priority level. IPL3 is a read-only bit so that the trap events cannot be masked by the user’s software. All interrupt registers are described in Register 8-1 through Register 8-33, in the following sections. The PIC24FV32KA304 family of devices implements a total of 22 registers for the interrupt controller: • • • • • INTCON1 INTCON2 IFS0, IFS1, IFS3 and IFS4 IEC0, IEC1, IEC3 and IEC4 IPC0 through IPC5, IPC7 and IPC15 through IPC19 • INTTREG Global interrupt control functions are controlled from INTCON1 and INTCON2. INTCON1 contains the Interrupt Nesting Disable (NSTDIS) bit, as well as the control and status flags for the processor trap sources. The INTCON2 register controls the external interrupt request signal behavior and the use of the AIV table. The IFSx registers maintain all of the interrupt request flags. Each source of interrupt has a status bit, which is set by the respective peripherals, or external signal, and is cleared via software. The IECx registers maintain all of the interrupt enable bits. These control bits are used to individually enable interrupts from the peripherals or external signals. The IPCx registers are used to set the interrupt priority level for each source of interrupt. Each user interrupt source can be assigned to one of eight priority levels. DS39995B-page 82  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-1: U-0 — bit 15 R/W-0, HSC IPL2 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-9 bit 7-5 HSC = Hardware Settable/Clearable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown (2,3) SR: ALU STATUS REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — R-0, HSC DC(1) bit 8 R/W-0, HSC IPL1(2,3) R/W-0, HSC IPL0(2,3) R-0, HSC RA(1) R/W-0, HSC N(1) R/W-0, HSC OV(1) R/W-0, HSC Z(1) R/W-0, HSC C(1) bit 0 Unimplemented: Read as ‘0’ IPL: CPU Interrupt Priority Level Status bits(2,3) 111 = CPU interrupt priority level is 7 (15); user interrupts disabled 110 = CPU interrupt priority level is 6 (14) 101 = CPU interrupt priority level is 5 (13) 100 = CPU interrupt priority level is 4 (12) 011 = CPU interrupt priority level is 3 (11) 010 = CPU interrupt priority level is 2 (10) 001 = CPU interrupt priority level is 1 (9) 000 = CPU interrupt priority level is 0 (8) See Register 3-1 for the description of these bits, which are not dedicated to interrupt control functions. The IPL bits are concatenated with the IPL3 bit (CORCON) to form the CPU interrupt priority level. The value in parentheses indicates the interrupt priority level if IPL3 = 1. The IPL Status bits are read-only when NSTDIS (INTCON1) = 1. Bit 8 and bits 4 through 0 are described in Section 3.0 “CPU”. Note 1: 2: 3: Note:  2011 Microchip Technology Inc. DS39995B-page 83 PIC24FV32KA304 FAMILY REGISTER 8-2: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-4 bit 3 C = Clearable bit W = Writable bit ‘1’ = Bit is set HSC = Hardware Settable/Clearable bit U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — R/C-0, HSC IPL3 (2) CORCON: CPU CONTROL REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 PSV (1) U-0 — U-0 — bit 0 Unimplemented: Read as ‘0’ IPL3: CPU Interrupt Priority Level Status bit(2) 1 = CPU interrupt priority level is greater than 7 0 = CPU interrupt priority level is 7 or less Unimplemented: Read as ‘0’ See Register 3-2 for the description of this bit, which is not dedicated to interrupt control functions. The IPL3 bit is concatenated with the IPL bits (SR) to form the CPU interrupt priority level. Bit 2 is described in Section 3.0 “CPU”. bit 1-0 Note 1: 2: Note: DS39995B-page 84  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-3: R/W-0 NSTDIS bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 HS = Hardware Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — R/W-0, HS MATHERR R/W-0, HS ADDRERR R/W-0, HS STKERR R/W-0, HS OSCFAIL U-0 — bit 0 INTCON1: INTERRUPT CONTROL REGISTER 1 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 NSTDIS: Interrupt Nesting Disable bit 1 = Interrupt nesting is disabled 0 = Interrupt nesting is enabled Unimplemented: Read as ‘0’ MATHERR: Arithmetic Error Trap Status bit 1 = Overflow trap has occurred 0 = Overflow trap has not occurred ADDRERR: Address Error Trap Status bit 1 = Address error trap has occurred 0 = Address error trap has not occurred STKERR: Stack Error Trap Status bit 1 = Stack error trap has occurred 0 = Stack error trap has not occurred OSCFAIL: Oscillator Failure Trap Status bit 1 = Oscillator failure trap has occurred 0 = Oscillator failure trap has not occurred Unimplemented: Read as ‘0’ bit 14-5 bit 4 bit 3 bit 2 bit 1 bit 0  2011 Microchip Technology Inc. DS39995B-page 85 PIC24FV32KA304 FAMILY REGISTER 8-4: R/W-0 ALTIVT bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 HSC = Hardware Settable/Clearable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — R/W-0 INT2EP R/W-0 INT1EP INTCON2: INTERRUPT CONTROL REGISTER2 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 INT0EP bit 0 DISI R-0, HSC ALTIVT: Enable Alternate Interrupt Vector Table bit 1 = Use Alternate Interrupt Vector Table 0 = Use standard (default) vector table DISI: DISI Instruction Status bit 1 = DISI instruction is active 0 = DISI instruction is not active Unimplemented: Read as ‘0’ INT2EP: External Interrupt 2 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge INT1EP: External Interrupt 1 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge INT0EP: External Interrupt 0 Edge Detect Polarity Select bit 1 = Interrupt on negative edge 0 = Interrupt on positive edge bit 14 bit 13-3 bit 2 bit 1 bit 0 DS39995B-page 86  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-5: R/W-0, HS NVMIF bit 15 R/W-0, HS T2IF bit 7 IFS0: INTERRUPT FLAG STATUS REGISTER 0 U-0 — R/W-0, HS AD1IF R/W-0, HS U1TXIF R/W-0, HS U1RXIF R/W-0, HS SPI1IF R/W-0, HS SPF1IF R/W-0, HS T3IF bit 8 R/W-0, HS INT0IF bit 0 R/W-0, HS OC2IF R/W-0, HS IC2IF U-0 — R/W-0, HS T1IF R/W-0, HS OC1IF R/W-0, HS IC1IF Legend: R = Readable bit -n = Value at POR bit 15 HS = Hardware Settable bit W = Writable bit U = Unimplemented bit, read as ‘0’ ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 NVMIF: NVM Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ AD1IF: A/D Conversion Complete Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred U1TXIF: UART1 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred U1RXIF: UART1 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred SPI1IF: SPI1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred SPF1IF: SPI1 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred T3IF: Timer3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred T2IF: Timer2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred OC2IF: Output Compare Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred IC2IF: Input Capture Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ T1IF: Timer1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred OC1IF: Output Compare Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred  2011 Microchip Technology Inc. DS39995B-page 87 PIC24FV32KA304 FAMILY REGISTER 8-5: bit 1 IFS0: INTERRUPT FLAG STATUS REGISTER 0 (CONTINUED) bit 0 IC1IF: Input Capture Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred INT0IF: External Interrupt 0 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred REGISTER 8-6: R/W-0, HS U2TXIF bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 IFS1: INTERRUPT FLAG STATUS REGISTER 1 R/W-0, HS INT2IF R/W-0, HS T5IF R/W-0, HS T4IF U-0 — R/W-0, HS OC3IF U-0 — bit 8 U-0 — U-0 — R/W-0, HS INT1IF R/W-0, HS CNIF R/W-0, HS CMIF R/W-0 MI2C1IF R/W-0 SI2C1IF bit 0 R/W-0, HS U2RXIF HS = Hardware Settable bit W = Writable bit U = Unimplemented bit, read as ‘0’ ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8-5 bit 4 bit 3 bit 2 U2TXIF: UART2 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred U2RXIF: UART2 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred INT2IF: External Interrupt 2 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred T5IF: Timer5 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred T4IF: Timer4 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ OC3IF: Output Compare Channel 3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ INT1IF: External Interrupt 1 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred CNIF: Input Change Notification Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred CMIF: Comparator Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS39995B-page 88  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-6: bit 1 IFS1: INTERRUPT FLAG STATUS REGISTER 1 (CONTINUED) bit 0 MI2C1IF: Master I2C1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred SI2C1IF: Slave I2C1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred REGISTER 8-7: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-6 bit 5 IFS2: INTERRUPT FLAG STATUS REGISTER 2 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 U-0 — R/W-0, HS IC3IF U-0 — U-0 — U-0 — R/W-0, HS SPI2IF R/W-0, HS SPF2IF bit 0 HS = Hardware Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown Unimplemented: Read as ‘0’ IC3IF: Input Capture Channel 3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ SPI2IF: SPI2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred SPF2IF: SPI2 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4-2 bit 1 bit 0  2011 Microchip Technology Inc. DS39995B-page 89 PIC24FV32KA304 FAMILY REGISTER 8-8: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14 HS = Hardware Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — R/W-0, HS MI2C2IF R/W-0, HS SI2C2IF U-0 — bit 0 IFS3: INTERRUPT FLAG STATUS REGISTER 3 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 RTCIF R/W-0, HS Unimplemented: Read as ‘0’ RTCIF: Real-Time Clock and Calendar Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ MI2C2IF: Master I2C2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred SI2C2IF: Slave I2C2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ bit 13-3 bit 2 bit 1 bit 0 DS39995B-page 90  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-9: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-14 bit 13 HS = Hardware Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — R/W-0, HS CRCIF R/W-0, HS U2ERIF R/W-0, HS U1ERIF U-0 — bit 0 IFS4: INTERRUPT FLAG STATUS REGISTER 4 U-0 — R/W-0, HS CTMUIF U-0 — U-0 — U-0 — U-0 — R/W-0, HS HLVDIF bit 8 Unimplemented: Read as ‘0’ CTMUIF: CTMU Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ HLVDIF: High/Low-Voltage Detect Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ CRCIF: CRC Generator Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred U2ERIF: UART2 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred U1ERIF: UART1 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred Unimplemented: Read as ‘0’ bit 12-9 bit 8 bit 7-4 bit 3 bit 2 bit 1 bit 0  2011 Microchip Technology Inc. DS39995B-page 91 PIC24FV32KA304 FAMILY REGISTER 8-10: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-1 bit 0 HS = Hardware Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — IFS5: INTERRUPT FLAG STATUS REGISTER 5 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0, HS ULPWUIF bit 0 Unimplemented: Read as ‘0’ ULPWUIF: Ultra Low-Power Wake-up Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS39995B-page 92  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-11: R/W-0 NVMIE bit 15 R/W-0 T2IE bit 7 IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 U-0 — R/W-0 AD1IE R/W-0 U1TXIE R/W-0 U1RXIE R/W-0 SPI1IE R/W-0 SPF1IE R/W-0 T3IE bit 8 R/W-0 INT0IE bit 0 R/W-0 OC2IE R/W-0 IC2IE U-0 — R/W-0 T1IE R/W-0 OC1IE R/W-0 IC1IE Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 NVMIE: NVM Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ AD1IE: A/D Conversion Complete Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled U1TXIE: UART1 Transmitter Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled U1RXIE: UART1 Receiver Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled SPI1IE: SPI1 Transfer Complete Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled SPF1IE: SPI1 Fault Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled T3IE: Timer3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled T2IE: Timer2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled OC2IE: Output Compare Channel 2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled IC2IE: Input Capture Channel 2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ T1IE: Timer1 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled OC1IE: Output Compare Channel 1 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled  2011 Microchip Technology Inc. DS39995B-page 93 PIC24FV32KA304 FAMILY REGISTER 8-11: bit 1 IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 bit 0 IC1IE: Input Capture Channel 1 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled INT0IE: External Interrupt 0 Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled REGISTER 8-12: R/W-0 U2TXIE bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 IEC1: INTERRUPT ENABLE CONTROL REGISTER 1 R/W-0 INT2IE R/W-0 T5IE R/W-0 T4IE U-0 — R/W-0 OC3IE U-0 — bit 8 U-0 — U-0 — R/W-0 INT1IE R/W-0 CNIE R/W-0 CMIE R/W-0 MI2C1IE R/W-0 SI2C1IE bit 0 R/W-0 U2RXIE W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8-5 bit 4 bit 3 bit 2 U2TXIE: UART2 Transmitter Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled U2RXIE: UART2 Receiver Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled INT2IE: External Interrupt 2 Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled T5IE: Timer5 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled T4IE: Timer4 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ OC3IE: Output Compare 3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ INT1IE: External Interrupt 1 Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled CNIE: Input Change Notification Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled CMIE: Comparator Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled DS39995B-page 94  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-12: bit 1 IEC1: INTERRUPT ENABLE CONTROL REGISTER 1 bit 0 MI2C1IE: Master I2C1 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled SI2C1IE: Slave I2C1 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled REGISTER 8-13: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-6 bit 5 IEC2: INTERRUPT ENABLE CONTROL REGISTER 2 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 U-0 — R/W-0 IC3IE U-0 — U-0 — U-0 — R/W-0 SPI2IE R/W-0 SPF2IE bit 0 HS = Hardware Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown Unimplemented: Read as ‘0’ IC3IE: Input Capture Channel 3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ SPI2IE: SPI2 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled SPF2IE: SPI2 Fault Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 4-2 bit 1 bit 0  2011 Microchip Technology Inc. DS39995B-page 95 PIC24FV32KA304 FAMILY REGISTER 8-14: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — R/W-0 MI2C2IE R/W-0 SI2C2IE U-0 — bit 0 IEC3: INTERRUPT ENABLE CONTROL REGISTER 3 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 RTCIE Unimplemented: Read as ‘0’ RTCIE: Real-Time Clock and Calendar Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ MI2C2IE: Master I2C2 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled SI2C2IE: Slave I2C2 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ bit 13-3 bit 2 bit 1 bit 0 DS39995B-page 96  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-15: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-14 bit 13 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — R/W-0 CRCIE R/W-0 U2ERIE R/W-0 U1ERIE U-0 — bit 0 IEC4: INTERRUPT ENABLE CONTROL REGISTER 4 U-0 — R/W-0 CTMUIE U-0 — U-0 — U-0 — U-0 — R/W-0 HLVDIE bit 8 Unimplemented: Read as ‘0’ CTMUIE: CTMU Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ HLVDIE: High/Low-Voltage Detect Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ CRCIE: CRC Generator Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled U2ERIE: UART2 Error Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled U1ERIE: UART1 Error Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled Unimplemented: Read as ‘0’ bit 12-9 bit 8 bit 7-4 bit 3 bit 2 bit 1 bit 0  2011 Microchip Technology Inc. DS39995B-page 97 PIC24FV32KA304 FAMILY REGISTER 8-16: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-1 bit 0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — IEC5: INTERRUPT ENABLE CONTROL REGISTER 5 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 ULPWUIE bit 0 Unimplemented: Read as ‘0’ ULPWUIE: Ultra Low-Power Wake-up Interrupt Enable Bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled DS39995B-page 98  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-17: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 IC1IP2 R/W-0 IC1IP1 R/W-0 IC1IP0 U-0 — R/W-1 INT0IP2 R/W-0 INT0IP1 IPC0: INTERRUPT PRIORITY CONTROL REGISTER 0 R/W-0 T1IP1 R/W-0 T1IP0 U-0 — R/W-1 OC1IP2 R/W-0 OC1IP1 R/W-0 OC1IP0 bit 8 R/W-0 INT0IP0 bit 0 R/W-1 T1IP2 Unimplemented: Read as ‘0’ T1IP: Timer1 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 bit 10-8 Unimplemented: Read as ‘0’ OC1IP: Output Compare Channel 1 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 bit 6-4 Unimplemented: Read as ‘0’ IC1IP: Input Capture Channel 1 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 bit 2-0 Unimplemented: Read as ‘0’ INT0IP: External Interrupt 0 Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011 Microchip Technology Inc. DS39995B-page 99 PIC24FV32KA304 FAMILY REGISTER 8-18: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 IC2IP2 R/W-0 IC2IP1 R/W-0 IC2IP0 U-0 — U-0 — U-0 — U-0 — bit 0 IPC1: INTERRUPT PRIORITY CONTROL REGISTER 1 R/W-0 T2IP1 R/W-0 T2IP0 U-0 — R/W-1 OC2IP2 R/W-0 OC2IP1 R/W-0 OC2IP0 bit 8 R/W-1 T2IP2 Unimplemented: Read as ‘0’ T2IP: Timer2 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 bit 10-8 Unimplemented: Read as ‘0’ OC2IP: Output Compare Channel 2 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 bit 6-4 Unimplemented: Read as ‘0’ IC2IP: Input Capture Channel 2 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39995B-page 100  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-19: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 SPF1IP2 R/W-0 SPF1IP1 R/W-0 SPF1IP0 U-0 — R/W-1 T3IP2 R/W-0 T3IP1 IPC2: INTERRUPT PRIORITY CONTROL REGISTER 2 R/W-0 U1RXIP1 R/W-0 U1RXIP0 U-0 — R/W-1 SPI1IP2 R/W-0 SPI1IP1 R/W-0 SPI1IP0 bit 8 R/W-0 T3IP0 bit 0 R/W-1 U1RXIP2 Unimplemented: Read as ‘0’ U1RXIP: UART1 Receiver Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 bit 10-8 Unimplemented: Read as ‘0’ SPI1IP: SPI1 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 bit 6-4 Unimplemented: Read as ‘0’ SPF1IP: SPI1 Fault Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 bit 2-0 Unimplemented: Read as ‘0’ T3IP: Timer3 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011 Microchip Technology Inc. DS39995B-page 101 PIC24FV32KA304 FAMILY REGISTER 8-20: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 AD1IP2 R/W-0 AD1IP1 R/W-0 AD1IP0 U-0 — R/W-1 U1TXIP2 R/W-0 U1TXIP1 IPC3: INTERRUPT PRIORITY CONTROL REGISTER 3 R/W-0 NVMIP1 R/W-0 NVMIP0 U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 U1TXIP0 bit 0 R/W-1 NVMIP2 Unimplemented: Read as ‘0’ NVMIP: NVM Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11-7 bit 6-4 Unimplemented: Read as ‘0’ AD1IP: A/D Conversion Complete Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 bit 2-0 Unimplemented: Read as ‘0’ U1TXIP: UART1 Transmitter Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled DS39995B-page 102  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-21: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 MI2C1P2 R/W-0 MI2C1P1 R/W-0 MI2C1P0 U-0 — R/W-1 SI2C1P2 R/W-0 SI2C1P1 IPC4: INTERRUPT PRIORITY CONTROL REGISTER 4 R/W-0 CNIP1 R/W-0 CNIP0 U-0 — R/W-1 CMIP2 R/W-0 CMIP1 R/W-0 CMIP0 bit 8 R/W-0 SI2C1P0 bit 0 R/W-1 CNIP2 Unimplemented: Read as ‘0’ CNIP: Input Change Notification Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 bit 10-8 Unimplemented: Read as ‘0’ CMIP: Comparator Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 bit 6-4 Unimplemented: Read as ‘0’ MI2C1P: Master I2C1 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 bit 2-0 Unimplemented: Read as ‘0’ SI2C1P: Slave I2C1 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011 Microchip Technology Inc. DS39995B-page 103 PIC24FV32KA304 FAMILY REGISTER 8-22: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-3 bit 2-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — R/W-1 INT1IP2 R/W-0 INT1IP1 IPC5: INTERRUPT PRIORITY CONTROL REGISTER 5 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 INT1IP0 bit 0 Unimplemented: Read as ‘0’ INT1IP: External Interrupt 1 Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled DS39995B-page 104  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-23: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 OC3IP2 R/W-0 OC3IP1 R/W-0 OC3IP0 U-0 — U-0 — U-0 — U-0 — bit 0 IPC6: INTERRUPT PRIORITY CONTROL REGISTER 6 R/W-0 T4IP1 R/W-0 T4IP0 U-0 — U-0 — U-0 — U-0 — bit 8 R/W-1 T4IP2 Unimplemented: Read as ‘0’ T4IP: Timer4 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11-7 bit 6-4 Unimplemented: Read as ‘0’ OC3IP: Output Compare Channel 3 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2011 Microchip Technology Inc. DS39995B-page 105 PIC24FV32KA304 FAMILY REGISTER 8-24: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 INT2IP2 R/W-0 INT2IP1 R/W-0 INT2IP0 U-0 — R/W-1 T5IP2 R/W-0 T5IP1 IPC7: INTERRUPT PRIORITY CONTROL REGISTER 7 R/W-0 U2TXIP1 R/W-0 U2TXIP0 U-0 — R/W-1 U2RXIP2 R/W-0 U2RXIP1 R/W-0 U2RXIP0 bit 8 R/W-0 T5IP0 bit 0 R/W-1 U2TXIP2 Unimplemented: Read as ‘0’ U2TXIP: UART2 Transmitter Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 bit 10-8 Unimplemented: Read as ‘0’ U2RXIP: UART2 Receiver Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 bit 6-4 Unimplemented: Read as ‘0’ INT2IP: External Interrupt 2 Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 bit 2-0 Unimplemented: Read as ‘0’ T5IP: Timer5 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled DS39995B-page 106  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-25: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-7 bit 6-4 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 SPI2IP2 R/W-0 SPI2IP1 R/W-0 SPI2IP0 U-0 — R/W-1 SPF2IP2 R/W-0 SPF2IP1 IPC8: INTERRUPT PRIORITY CONTROL REGISTER 8 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 SPF2IP0 bit 0 Unimplemented: Read as ‘0’ SPI2IP: SPI2 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 bit 2-0 Unimplemented: Read as ‘0’ SPF2IP: SPI2 Fault Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011 Microchip Technology Inc. DS39995B-page 107 PIC24FV32KA304 FAMILY REGISTER 8-26: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-7 bit 6-4 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 IC3IP2 R/W-0 IC3IP1 R/W-0 IC3IP0 U-0 — U-0 — U-0 — U-0 — bit 0 IPC9: INTERRUPT PRIORITY CONTROL REGISTER 9 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 Unimplemented: Read as ‘0’ IC3IP: Input Capture Channel 3 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39995B-page 108  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-27: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-11 bit 10-8 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 SI2C2IP2 R/W-0 SI2C2IP1 R/W-0 SI2C2IP0 U-0 — U-0 — U-0 — U-0 — bit 0 IPC12: INTERRUPT PRIORITY CONTROL REGISTER 12 U-0 — U-0 — U-0 — U-0 — R/W-1 MI2C2IP2 R/W-0 MI2C2IP1 R/W-0 MI2C2IP0 bit 8 Unimplemented: Read as ‘0’ MI2C2IP : Master I2C2 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 bit 6-4 Unimplemented: Read as ‘0’ SI2C2IP: Slave I2C2 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2011 Microchip Technology Inc. DS39995B-page 109 PIC24FV32KA304 FAMILY REGISTER 8-28: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-11 bit 10-8 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 0 IPC15: INTERRUPT PRIORITY CONTROL REGISTER 15 U-0 — U-0 — U-0 — U-0 — R/W-1 RTCIP2 R/W-0 RTCIP1 R/W-0 RTCIP0 bit 8 Unimplemented: Read as ‘0’ RTCIP: Real-Time Clock and Calendar Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7-0 Unimplemented: Read as ‘0’ DS39995B-page 110  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-29: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-12 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-1 U1ERIP2 R/W-0 U1ERIP1 R/W-0 U1ERIP0 U-0 — U-0 — U-0 — U-0 — bit 0 IPC16: INTERRUPT PRIORITY CONTROL REGISTER 16 R/W-0 CRCIP1 R/W-0 CRCIP0 U-0 — R/W-1 U2ERIP2 R/W-0 U2ERIP1 R/W-0 U2ERIP0 bit 8 R/W-1 CRCIP2 Unimplemented: Read as ‘0’ CRCIP: CRC Generator Error Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 bit 10-8 Unimplemented: Read as ‘0’ U2ERIP: UART2 Error Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 bit 6-4 Unimplemented: Read as ‘0’ U1ERIP: UART1 Error Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2011 Microchip Technology Inc. DS39995B-page 111 PIC24FV32KA304 FAMILY REGISTER 8-30: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-3 bit 2-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — R/W-1 HLVDIP2 R/W-0 HLVDIP1 IPC18: INTERRUPT PRIORITY CONTROL REGISTER 18 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 HLVDIP0 bit 0 Unimplemented: Read as ‘0’ HLVDIP: High/Low-Voltage Detect Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled REGISTER 8-31: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-7 bit 6-4 IPC19: INTERRUPT PRIORITY CONTROL REGISTER 19 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-1 CTMUIP2 R/W-0 CTMUIP1 R/W-0 CTMUIP0 U-0 — U-0 — U-0 — U-0 — bit 0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown Unimplemented: Read as ‘0’ CTMUIP: CTMU Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS39995B-page 112  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 8-32: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-3 bit 6-4 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — R/W-1 ULPWUIP2 R/W-0 ULPWUIP1 IPC20: INTERRUPT PRIORITY CONTROL REGISTER 20 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 ULPWUIP0 bit 0 Unimplemented: Read as ‘0’ ULPWUIP: Ultra Low-Power Wake-up Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011 Microchip Technology Inc. DS39995B-page 113 PIC24FV32KA304 FAMILY REGISTER 8-33: R-0 CPUIRQ bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R-0 VECNUM6 R-0 VECNUM5 R-0 VECNUM4 R-0 VECNUM3 R-0 VECNUM2 R-0 VECNUM1 R-0 VECNUM0 bit 0 INTTREG: INTERRUPT CONTROL AND STATUS REGISTER U-0 — R/W-0 VHOLD U-0 — R-0 ILR3 R-0 ILR2 R-0 ILR1 R-0 ILR0 bit 8 CPUIRQ: Interrupt Request from Interrupt Controller CPU bit 1 = An interrupt request has occurred but has not yet been Acknowledged by the CPU (this will happen when the CPU priority is higher than the interrupt priority) 0 = No interrupt request is left unacknowledged Unimplemented: Read as ‘0’ VHOLD: Vector Hold bit Allows vector number capture and changes what Interrupt is stored in the VECNUM bit. 1 = VECNUM will contain the value of the highest priority pending interrupt, instead of the current interrupt 0 = VECNUM will contain the value of the last Acknowledged interrupt (last interrupt that has occurred with higher priority than the CPU, even if other interrupts are pending) Unimplemented: Read as ‘0’ ILR: New CPU Interrupt Priority Level bits 1111 = CPU interrupt priority level is 15 • • • bit 14 bit 13 bit 12 bit 11-8 0001 = CPU interrupt priority level is 1 0000 = CPU interrupt priority level is 0 bit 7 bit 6-0 Unimplemented: Read as ‘0’ VECNUM: Vector Number of Pending Interrupt bits 0111111 = Interrupt vector pending is number 135 • • • 0000001 = Interrupt vector pending is number 9 0000000 = Interrupt vector pending is number 8 DS39995B-page 114  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 8.4 8.4.1 1. 2. Interrupt Setup Procedures INITIALIZATION 8.4.3 TRAP SERVICE ROUTINE (TSR) To configure an interrupt source: Set the NSTDIS Control bit (INTCON1) if nested interrupts are not desired. Select the user-assigned priority level for the interrupt source by writing the control bits in the appropriate IPCx register. The priority level will depend on the specific application and type of interrupt source. If multiple priority levels are not desired, the IPCx register control bits for all enabled interrupt sources may be programmed to the same non-zero value. Note: At a device Reset, the IPCx registers are initialized, such that all user interrupt sources are assigned to Priority Level 4. A Trap Service Routine (TSR) is coded like an ISR, except that the appropriate trap status flag in the INTCON1 register must be cleared to avoid re-entry into the TSR. 8.4.4 INTERRUPT DISABLE All user interrupts can be disabled using the following procedure: 1. 2. Push the current SR value onto the software stack using the PUSH instruction. Force the CPU to Priority Level 7 by inclusive ORing the value, OEh with SRL. To enable user interrupts, the POP instruction may be used to restore the previous SR value. Only user interrupts with a priority level of 7 or less can be disabled. Trap sources (Level 8-15) cannot be disabled. The DISI instruction provides a convenient way to disable interrupts of Priority Levels 1-6 for a fixed period. Level 7 interrupt sources are not disabled by the DISI instruction. 3. 4. Clear the interrupt flag status bit associated with the peripheral in the associated IFSx register. Enable the interrupt source by setting the interrupt enable control bit associated with the source in the appropriate IECx register. 8.4.2 INTERRUPT SERVICE ROUTINE The method that is used to declare an ISR and initialize the IVT with the correct vector address depends on the programming language (i.e., C or assembler) and the language development toolsuite that is used to develop the application. In general, the user must clear the interrupt flag in the appropriate IFSx register for the source of the interrupt that the ISR handles. Otherwise, the ISR will be re-entered immediately after exiting the routine. If the ISR is coded in assembly language, it must be terminated using a RETFIE instruction to unstack the saved PC value, SRL value and old CPU priority level.  2011 Microchip Technology Inc. DS39995B-page 115 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 116  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 9.0 Note: OSCILLATOR CONFIGURATION This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on Oscillator Configuration, refer to the “PIC24F Family Reference Manual”, Section 38. “Oscillator with 500 kHz Low-Power FRC” (DS39726). • Software-controllable switching between various clock sources. • Software-controllable postscaler for selective clocking of CPU for system power savings. • System frequency range declaration bits for EC mode. When using an external clock source, the current consumption is reduced by setting the declaration bits to the expected frequency range. • A Fail-Safe Clock Monitor (FSCM) that detects clock failure and permits safe application recovery or shutdown. A simplified diagram of the oscillator system is shown in Figure 9-1. The oscillator system for the PIC24FV32KA304 family of devices has the following features: • A total of five external and internal oscillator options as clock sources, providing 11 different clock modes. • On-chip 4x Phase Locked Loop (PLL) to boost internal operating frequency on select internal and external oscillator sources. FIGURE 9-1: PIC24FV32KA304 FAMILY CLOCK DIAGRAM Primary Oscillator OSCO XT, HS, EC REFOCON Reference Clock Generator REFO OSCI 4 x PLL 8 MHz 4 MHz XTPLL, HSPLL ECPLL,FRCPLL 8 MHz FRC Oscillator 500 kHz LPFRC Oscillator Postscaler FRCDIV Peripherals CLKDIV FRC CLKO 31 kHz (nominal) Postscaler LPRC Oscillator LPRC CPU Secondary Oscillator SOSCO SOSCEN Enable Oscillator SOSC CLKDIV Clock Control Logic Fail-Safe Clock Monitor SOSCI WDT, PWRT, DSWDT Clock Source Option for Other Modules  2011 Microchip Technology Inc. DS39995B-page 117 PIC24FV32KA304 FAMILY 9.1 CPU Clocking Scheme 9.2 Initial Configuration on POR The system clock source can be provided by one of four sources: • Primary Oscillator (POSC) on the OSCI and OSCO pins • Secondary Oscillator (SOSC) on the SOSCI and SOSCO pins The PIC24FV32KA304 family devices consist of two types of secondary oscillator: - High-Power Secondary Oscillator - Low-Power Secondary Oscillator These can be selected by using the SOSCSEL (FOSC) bit. • Fast Internal RC (FRC) Oscillator - 8 MHz FRC Oscillator - 500 kHz Lower Power FRC Oscillator • Low-Power Internal RC (LPRC) Oscillator with two modes: - High-Power/High Accuracy mode - Low-Power/Low Accuracy mode The primary oscillator and 8 MHz FRC sources have the option of using the internal 4x PLL. The frequency of the FRC clock source can optionally be reduced by the programmable clock divider. The selected clock source generates the processor and peripheral clock sources. The processor clock source is divided by two to produce the internal instruction cycle clock, FCY. In this document, the instruction cycle clock is also denoted by FOSC/2. The internal instruction cycle clock, FOSC/2, can be provided on the OSCO I/O pin for some operating modes of the primary oscillator. The oscillator source (and operating mode) that is used at a device Power-on Reset (POR) event is selected using Configuration bit settings. The oscillator Configuration bit settings are located in the Configuration registers in the program memory (For more information, see Section 26.1 “Configuration Bits”). The Primary Oscillator Configuration bits, POSCMD (FOSC), and the Initial Oscillator Select Configuration bits, FNOSC (FOSCSEL), select the oscillator source that is used at a POR. The FRC Primary Oscillator with Postscaler (FRCDIV) is the default (unprogrammed) selection. The secondary oscillator, or one of the internal oscillators, may be chosen by programming these bit locations. The EC mode frequency range Configuration bits, POSCFREQ (FOSC), optimize power consumption when running in EC mode. The default configuration is “frequency range is greater than 8 MHz”. The Configuration bits allow users to choose between the various clock modes, shown in Table 9-1. 9.2.1 CLOCK SWITCHING MODE CONFIGURATION BITS The FCKSM Configuration bits (FOSC) are used jointly to configure device clock switching and the FSCM. Clock switching is enabled only when FCKSM1 is programmed (‘0’). The FSCM is enabled only when FCKSM are both programmed (‘00’). TABLE 9-1: CONFIGURATION BIT VALUES FOR CLOCK SELECTION Oscillator Mode Oscillator Source Internal Internal Internal Secondary Primary Primary Primary Primary Primary Internal Internal POSCMD 11 11 11 00 10 00 10 01 00 11 11 FNOSC 111 110 101 100 011 011 010 010 010 001 000 1 1 Notes 1, 2 1 1 1 8 MHz FRC Oscillator with Postscaler (FRCDIV) 500 kHz FRC Oscillator with Postscaler (LPFRCDIV) Low-Power RC Oscillator (LPRC) Secondary (Timer1) Oscillator (SOSC) Primary Oscillator (HS) with PLL Module (HSPLL) Primary Oscillator (EC) with PLL Module (ECPLL) Primary Oscillator (HS) Primary Oscillator (XT) Primary Oscillator (EC) 8 MHz FRC Oscillator with PLL Module (FRCPLL) 8 MHz FRC Oscillator (FRC) Note 1: 2: OSCO pin function is determined by the OSCIOFNC Configuration bit. This is the default oscillator mode for an unprogrammed (erased) device. DS39995B-page 118  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 9.3 Control Registers The operation of the oscillator is controlled by three Special Function Registers (SFRs): • OSCCON • CLKDIV • OSCTUN The OSCCON register (Register 9-1) is the main control register for the oscillator. It controls clock source switching and allows the monitoring of clock sources. The Clock Divider register (Register 9-2) controls the features associated with Doze mode, as well as the postscaler for the FRC oscillator. The FRC Oscillator Tune register (Register 9-3) allows the user to fine tune the FRC oscillator over a range of approximately ±5.25%. Each bit increment or decrement changes the factory calibrated frequency of the FRC oscillator by a fixed amount. REGISTER 9-1: U-0 — bit 15 R/SO-0, HSC CLKLOCK bit 7 Legend: OSCCON: OSCILLATOR CONTROL REGISTER R-0, HSC COSC2 R-0, HSC COSC1 R-0, HSC COSC0 U-0 — R/W-x(1) NOSC2 R/W-x(1) NOSC1 R/W-x(1) NOSC0 bit 8 U-0 — R-0, HSC(2) LOCK U-0 — R/CO-0, HS CF R/W-0(3) SOSCDRV R/W-0 SOSCEN R/W-0 OSWEN bit 0 HSC = Hardware Settable/Clearable bit CO = Clearable Only bit W = Writable bit ‘1’ = Bit is set SO = Settable Only bit U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown HS = Hardware Settable bit R = Readable bit -n = Value at POR bit 15 bit 14-12 Unimplemented: Read as ‘0’ COSC: Current Oscillator Selection bits 111 = 8 MHz Fast RC Oscillator with Postscaler (FRCDIV) 110 = 500 kHz Low-Power Fast RC Oscillator (FRC) with Postscaler (LPFRCDIV) 101 = Low-Power RC Oscillator (LPRC) 100 = Secondary Oscillator (SOSC) 011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = 8 MHz FRC Oscillator with Postscaler and PLL module (FRCPLL) 000 = 8 MHz FRC Oscillator (FRC) Unimplemented: Read as ‘0’ NOSC: New Oscillator Selection bits(1) 111 = 8 MHz Fast RC Oscillator with Postscaler (FRCDIV) 110 = 500 kHz Low-Power Fast RC Oscillator (FRC) with Postscaler (LPFRCDIV) 101 = Low-Power RC Oscillator (LPRC) 100 = Secondary Oscillator (SOSC) 011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = 8 MHz FRC Oscillator with Postscaler and PLL module (FRCPLL) 000 = 8 MHz FRC Oscillator (FRC) Reset values for these bits are determined by the FNOSC Configuration bits. Also resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected. When SOSC is selected to run from a digital clock input, rather than an external crystal (SOSCSRC = 0), this bit has no effect. bit 11 bit 10-8 Note 1: 2: 3:  2011 Microchip Technology Inc. DS39995B-page 119 PIC24FV32KA304 FAMILY REGISTER 9-1: bit 7 OSCCON: OSCILLATOR CONTROL REGISTER (CONTINUED) CLKLOCK: Clock Selection Lock Enabled bit If FSCM is enabled (FCKSM1 = 1): 1 = Clock and PLL selections are locked 0 = Clock and PLL selections are not locked and may be modified by setting the OSWEN bit If FSCM is disabled (FCKSM1 = 0): Clock and PLL selections are never locked and may be modified by setting the OSWEN bit. Unimplemented: Read as ‘0’ LOCK: PLL Lock Status bit(2) 1 = PLL module is in lock or PLL module start-up timer is satisfied 0 = PLL module is out of lock, PLL start-up timer is running or PLL is disabled Unimplemented: Read as ‘0’ CF: Clock Fail Detect bit 1 = FSCM has detected a clock failure 0 = No clock failure has been detected SOSCDRV: Secondary Oscillator Drive Strength bit(3) 1 = High-power SOSC circuit selected 0 = Low/high-power select is done via the SOSCSRC Configuration bit SOSCEN: 32 kHz Secondary Oscillator (SOSC) Enable bit 1 = Enable secondary oscillator 0 = Disable secondary oscillator OSWEN: Oscillator Switch Enable bit 1 = Initiate an oscillator switch to clock source specified by NOSC bits 0 = Oscillator switch is complete Reset values for these bits are determined by the FNOSC Configuration bits. Also resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected. When SOSC is selected to run from a digital clock input, rather than an external crystal (SOSCSRC = 0), this bit has no effect. bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Note 1: 2: 3: DS39995B-page 120  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 9-2: R/W-0 ROI bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 0 CLKDIV: CLOCK DIVIDER REGISTER R/W-0 DOZE2 R/W-1 DOZE1 R/W-1 DOZE0 R/W-0 DOZEN(1) R/W-0 RCDIV2 R/W-0 RCDIV1 R/W-1 RCDIV0 bit 8 ROI: Recover on Interrupt bit 1 = Interrupts clear the DOZEN bit, and reset the CPU and peripheral clock ratio to 1:1 0 = Interrupts have no effect on the DOZEN bit DOZE: CPU and Peripheral Clock Ratio Select bits 111 = 1:128 110 = 1:64 101 = 1:32 100 = 1:16 011 = 1:8 010 = 1:4 001 = 1:2 000 = 1:1 DOZEN: DOZE Enable bit(1) 1 = DOZE bits specify the CPU and peripheral clock ratio 0 = CPU and peripheral clock ratio set to 1:1 RCDIV: FRC Postscaler Select bits When OSCCON (COSC) = 111: 111 = 31.25 kHz (divide by 256) 110 = 125 kHz (divide by 64) 101 = 250 kHz (divide by 32) 100 = 500 kHz (divide by 16) 011 = 1 MHz (divide by 8) 010 = 2 MHz (divide by 4) 001 = 4 MHz (divide by 2) (default) 000 = 8 MHz (divide by 1) When OSCCON (COSC) = 110: 111 = 1.95 kHz (divide by 256) 110 = 7.81 kHz (divide by 64) 101 = 15.62 kHz (divide by 32) 100 = 31.25 kHz (divide by 16) 011 = 62.5 kHz (divide by 8) 010 = 125 kHz (divide by 4) 001 = 250 kHz (divide by 2) (default) 000 = 500 kHz (divide by 1) Unimplemented: Read as ‘0’ This bit is automatically cleared when the ROI bit is set and an interrupt occurs. bit 14-12 bit 11 bit 10-8 bit 7-0 Note 1:  2011 Microchip Technology Inc. DS39995B-page 121 PIC24FV32KA304 FAMILY REGISTER 9-3: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-6 bit 5-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — R/W-0 TUN5(1) R/W-0 TUN4(1) R/W-0 TUN3(1) R/W-0 TUN2(1) R/W-0 TUN1(1) OSCTUN: FRC OSCILLATOR TUNE REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 TUN0(1) bit 0 Unimplemented: Read as ‘0’ TUN: FRC Oscillator Tuning bits(1) 011111 = Maximum frequency deviation 011110 • • • 000001 000000 = Center frequency, oscillator is running at factory calibrated frequency 111111 • • • 100001 100000 = Minimum frequency deviation Note 1: Increments or decrements of TUN may not change the FRC frequency in equal steps over the FRC tuning range and may not be monotonic. DS39995B-page 122  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 9.4 Clock Switching Operation With few limitations, applications are free to switch between any of the four clock sources (POSC, SOSC, FRC and LPRC) under software control and at any time. To limit the possible side effects that could result from this flexibility, PIC24F devices have a safeguard lock built into the switching process. Note: The Primary Oscillator mode has three different submodes (XT, HS and EC), which are determined by the POSCMDx Configuration bits. While an application can switch to and from Primary Oscillator mode in software, it cannot switch between the different primary submodes without reprogramming the device. Once the basic sequence is completed, the system clock hardware responds automatically, as follows: 1. The clock switching hardware compares the COSCx bits with the new value of the NOSCx bits. If they are the same, then the clock switch is a redundant operation. In this case, the OSWEN bit is cleared automatically and the clock switch is aborted. If a valid clock switch has been initiated, the LOCK (OSCCON) and CF (OSCCON) bits are cleared. The new oscillator is turned on by the hardware if it is not currently running. If a crystal oscillator must be turned on, the hardware will wait until the OST expires. If the new source is using the PLL, then the hardware waits until a PLL lock is detected (LOCK = 1). The hardware waits for 10 clock cycles from the new clock source and then performs the clock switch. The hardware clears the OSWEN bit to indicate a successful clock transition. In addition, the NOSCx bits value is transferred to the COSCx bits. The old clock source is turned off at this time, with the exception of LPRC (if WDT, FSCM or RTCC with LPRC as clock source are enabled) or SOSC (if SOSCEN remains enabled). Note 1: The processor will continue to execute code throughout the clock switching sequence. Timing-sensitive code should not be executed during this time. 2: Direct clock switches between any Primary Oscillator mode with PLL and FRCPLL mode are not permitted. This applies to clock switches in either direction. In these instances, the application must switch to FRC mode as a transition clock source between the two PLL modes. 2. 3. 9.4.1 ENABLING CLOCK SWITCHING To enable clock switching, the FCKSM1 Configuration bit in the FOSC Configuration register must be programmed to ‘0’. (Refer to Section 26.0 “Special Features” for further details.) If the FCKSM1 Configuration bit is unprogrammed (‘1’), the clock switching function and FSCM function are disabled. This is the default setting. The NOSCx control bits (OSCCON) do not control the clock selection when clock switching is disabled. However, the COSCx bits (OSCCON) will reflect the clock source selected by the FNOSCx Configuration bits. The OSWEN control bit (OSCCON) has no effect when clock switching is disabled; it is held at ‘0’ at all times. 4. 5. 6. 9.4.2 OSCILLATOR SWITCHING SEQUENCE At a minimum, performing a clock switch requires this basic sequence: 1. If desired, read the COSCx bits (OSCCON), to determine the current oscillator source. Perform the unlock sequence to allow a write to the OSCCON register high byte. Write the appropriate value to the NOSCx bits (OSCCON) for the new oscillator source. Perform the unlock sequence to allow a write to the OSCCON register low byte. Set the OSWEN bit to initiate the oscillator switch. 2. 3. 4. 5.  2011 Microchip Technology Inc. DS39995B-page 123 PIC24FV32KA304 FAMILY The following code sequence for a clock switch is recommended: 1. 2. Disable interrupts during the OSCCON register unlock and write sequence. Execute the unlock sequence for the OSCCON high byte by writing 78h and 9Ah to OSCCON in two back-to-back instructions. Write new oscillator source to the NOSCx bits in the instruction immediately following the unlock sequence. Execute the unlock sequence for the OSCCON low byte by writing 46h and 57h to OSCCON in two back-to-back instructions. Set the OSWEN bit in the instruction immediately following the unlock sequence. Continue to execute code that is not clock-sensitive (optional). Invoke an appropriate amount of software delay (cycle counting) to allow the selected oscillator and/or PLL to start and stabilize. Check to see if OSWEN is ‘0’. If it is, the switch was successful. If OSWEN is still set, then check the LOCK bit to determine the cause of failure. 9.5 Reference Clock Output 3. In addition to the CLKO output (FOSC/2) available in certain oscillator modes, the device clock in the PIC24FV32KA304 family devices can also be configured to provide a reference clock output signal to a port pin. This feature is available in all oscillator configurations and allows the user to select a greater range of clock submultiples to drive external devices in the application. This reference clock output is controlled by the REFOCON register (Register 9-4). Setting the ROEN bit (REFOCON) makes the clock signal available on the REFO pin. The RODIV bits (REFOCON) enable the selection of 16 different clock divider options. The ROSSLP and ROSEL bits (REFOCON) control the availability of the reference output during Sleep mode. The ROSEL bit determines if the oscillator on OSC1 and OSC2, or the current system clock source, is used for the reference clock output. The ROSSLP bit determines if the reference source is available on REFO when the device is in Sleep mode. To use the reference clock output in Sleep mode, both the ROSSLP and ROSEL bits must be set. The device clock must also be configured for one of the primary modes (EC, HS or XT); otherwise, if the ROSEL bit is not also set, the oscillator on OSC1 and OSC2 will be powered down when the device enters Sleep mode. Clearing the ROSEL bit allows the reference output frequency to change as the system clock changes during any clock switches. 4. 5. 6. 7. 8. The core sequence for unlocking the OSCCON register and initiating a clock switch is shown in Example 9-1. EXAMPLE 9-1: BASIC CODE SEQUENCE FOR CLOCK SWITCHING ;Place the new oscillator selection in W0 ;OSCCONH (high byte) Unlock Sequence MOV #OSCCONH, w1 MOV #0x78, w2 MOV #0x9A, w3 MOV.b w2, [w1] MOV.b w3, [w1] ;Set new oscillator selection MOV.b WREG, OSCCONH ;OSCCONL (low byte) unlock sequence MOV #OSCCONL, w1 MOV #0x46, w2 MOV #0x57, w3 MOV.b w2, [w1] MOV.b w3, [w1] ;Start oscillator switch operation BSET OSCCON,#0 DS39995B-page 124  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 9-4: R/W-0 ROEN bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 0 REFOCON: REFERENCE OSCILLATOR CONTROL REGISTER U-0 — R/W-0 ROSSLP R/W-0 ROSEL R/W-0 RODIV3 R/W-0 RODIV2 R/W-0 RODIV1 R/W-0 RODIV0 bit 8 ROEN: Reference Oscillator Output Enable bit 1 = Reference oscillator enabled on REFO pin 0 = Reference oscillator disabled Unimplemented: Read as ‘0’ ROSSLP: Reference Oscillator Output Stop in Sleep bit 1 = Reference oscillator continues to run in Sleep 0 = Reference oscillator is disabled in Sleep ROSEL: Reference Oscillator Source Select bit 1 = Primary oscillator used as the base clock(1) 0 = System clock used as the base clock; base clock reflects any clock switching of the device RODIV: Reference Oscillator Divisor Select bits 1111 = Base clock value divided by 32,768 1110 = Base clock value divided by 16,384 1101 = Base clock value divided by 8,192 1100 = Base clock value divided by 4,096 1011 = Base clock value divided by 2,048 1010 = Base clock value divided by 1,024 1001 = Base clock value divided by 512 1000 = Base clock value divided by 256 0111 = Base clock value divided by 128 0110 = Base clock value divided by 64 0101 = Base clock value divided by 32 0100 = Base clock value divided by 16 0011 = Base clock value divided by 8 0010 = Base clock value divided by 4 0001 = Base clock value divided by 2 0000 = Base clock value Unimplemented: Read as ‘0’ The crystal oscillator must be enabled using the FOSC bits; the crystal maintains the operation in Sleep mode. bit 14 bit 13 bit 12 bit 11-8 bit 7-0 Note 1:  2011 Microchip Technology Inc. DS39995B-page 125 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 126  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 10.0 Note: POWER-SAVING FEATURES This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information, refer to the “PIC24F Family Reference Manual”, ”Section 39. Power-Saving Features with Deep Sleep” (DS39727). The assembly syntax of the PWRSAV instruction is shown in Example 10-1. Note: SLEEP_MODE and IDLE_MODE are constants defined in the assembler include file for the selected device. The PIC24FV32KA304 family of devices provides the ability to manage power consumption by selectively managing clocking to the CPU and the peripherals. In general, a lower clock frequency and a reduction in the number of circuits being clocked constitutes lower consumed power. All PIC24F devices manage power consumption in four different ways: • Clock frequency • Instruction-based Sleep, Idle and Deep Sleep modes • Software Controlled Doze mode • Selective peripheral control in software Combinations of these methods can be used to selectively tailor an application’s power consumption, while still maintaining critical application features, such as timing-sensitive communications. Sleep and Idle modes can be exited as a result of an enabled interrupt, WDT time-out or a device Reset. When the device exits these modes, it is said to “wake-up”. 10.2.1 SLEEP MODE Sleep mode includes these features: • The system clock source is shut down. If an on-chip oscillator is used, it is turned off. • The device current consumption will be reduced to a minimum provided that no I/O pin is sourcing current. • The I/O pin directions and states are frozen. • The Fail-Safe Clock Monitor does not operate during Sleep mode since the system clock source is disabled. • The LPRC clock will continue to run in Sleep mode if the WDT or RTCC with LPRC as clock source is enabled. • The WDT, if enabled, is automatically cleared prior to entering Sleep mode. • Some device features, or peripherals, may continue to operate in Sleep mode. This includes items, such as the input change notification on the I/O ports, or peripherals that use an external clock input. Any peripheral that requires the system clock source for its operation will be disabled in Sleep mode. The device will wake-up from Sleep mode on any of these events: • On any interrupt source that is individually enabled • On any form of device Reset • On a WDT time-out On wake-up from Sleep, the processor will restart with the same clock source that was active when Sleep mode was entered. 10.1 Clock Frequency and Clock Switching PIC24F devices allow for a wide range of clock frequencies to be selected under application control. If the system clock configuration is not locked, users can choose low-power or high-precision oscillators by simply changing the NOSC bits. The process of changing a system clock during operation, as well as limitations to the process, are discussed in more detail in Section 9.0 “Oscillator Configuration”. 10.2 Instruction-Based Power-Saving Modes PIC24F devices have two special power-saving modes that are entered through the execution of a special PWRSAV instruction. Sleep mode stops clock operation and halts all code execution; Idle mode halts the CPU and code execution, but allows peripheral modules to continue operation. Deep Sleep mode stops clock operation, code execution and all peripherals except RTCC and DSWDT. It also freezes I/O states and removes power to SRAM and Flash memory. EXAMPLE 10-1: PWRSAV PWRSAV BSET PWRSAV PWRSAV INSTRUCTION SYNTAX ; ; ; ; Put the device into SLEEP mode Put the device into IDLE mode Enable Deep Sleep Put the device into Deep SLEEP mode #SLEEP_MODE #IDLE_MODE DSCON, #DSEN #SLEEP_MODE  2011 Microchip Technology Inc. DS39995B-page 127 PIC24FV32KA304 FAMILY 10.2.2 IDLE MODE 10.2.4.1 Entering Deep Sleep Mode Idle mode has these features: • The CPU will stop executing instructions. • The WDT is automatically cleared. • The system clock source remains active. By default, all peripheral modules continue to operate normally from the system clock source, but can also be selectively disabled (see Section 10.6 “Selective Peripheral Module Control”). • If the WDT or FSCM is enabled, the LPRC will also remain active. The device will wake from Idle mode on any of these events: • Any interrupt that is individually enabled • Any device Reset • A WDT time-out On wake-up from Idle, the clock is re-applied to the CPU and instruction execution begins immediately, starting with the instruction following the PWRSAV instruction or the first instruction in the ISR. Deep Sleep mode is entered by setting the DSEN bit in the DSCON register, and then executing a Sleep command (PWRSAV #SLEEP_MODE). An unlock sequence is required to set the DSEN bit. Once the DSEN bit has been set, there is no time limit before the SLEEP command can be executed. The DSEN bit is automatically cleared when exiting the Deep Sleep mode. Note: To re-enter Deep Sleep after a Deep Sleep wake-up, allow a delay of at least 3 TCY after clearing the RELEASE bit. The sequence to enter Deep Sleep mode is: 1. If the application requires the Deep Sleep WDT, enable it and configure its clock source. For more information on Deep Sleep WDT, see Section 10.2.4.5 “Deep Sleep WDT”. If the application requires Deep Sleep BOR, enable it by programming the DSLPBOR Configuration bit (FDS). If the application requires wake-up from Deep Sleep on RTCC alarm, enable and configure the RTCC module For more information on RTCC, see Section 19.0 “Real-Time Clock and Calendar (RTCC)”. If needed, save any critical application context data by writing it to the DSGPR0 and DSGPR1 registers (optional). Enable Deep Sleep mode by setting the DSEN bit (DSCON). Note: 6. An unlock sequence is required to set the DSEN bit. 2. 10.2.3 INTERRUPTS COINCIDENT WITH POWER SAVE INSTRUCTIONS 3. Any interrupt that coincides with the execution of a PWRSAV instruction will be held off until entry into Sleep or Idle mode has completed. The device will then wake-up from Sleep or Idle mode. 4. 10.2.4 DEEP SLEEP MODE 5. In PIC24FV32KA304 family devices, Deep Sleep mode is intended to provide the lowest levels of power consumption available without requiring the use of external switches to completely remove all power from the device. Entry into Deep Sleep mode is completely under software control. Exit from Deep Sleep mode can be triggered from any of the following events: • • • • • • POR event MCLR event RTCC alarm (If the RTCC is present) External Interrupt 0 Deep Sleep Watchdog Timer (DSWDT) time-out Ultra Low-Power Wake-up (ULPWU) Event Enter Deep Sleep mode by issuing a PWRSAV #0 instruction. Any time the DSEN bit is set, all bits in the DSWAKE register will be automatically cleared. To set the DSEN bit, the unlock sequence in Example 10-2 is required: EXAMPLE 10-2: THE UNLOCK SEQUENCE //Disable Interrupts For 5 instructions asm volatile(“disi #5”); //Issue Unlock Sequence asm volatile mov #0x55, W0; mov W0, NVMKEY; mov #0xAA, W1; mov W1, NVMKEY; bset DSCON, #DSEN In Deep Sleep mode, it is possible to keep the device Real-Time Clock and Calendar (RTCC) running without the loss of clock cycles. The device has a dedicated Deep Sleep Brown-out Reset (DSBOR) and a Deep Sleep Watchdog Timer Reset (DSWDT) for monitoring voltage and time-out events. The DSBOR and DSWDT are independent of the standard BOR and WDT used with other power-managed modes (Sleep, Idle and Doze). DS39995B-page 128  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 10.2.4.2 Exiting Deep Sleep Mode Deep Sleep mode exits on any one of the following events: • POR event on VDD supply. If there is no DSBOR circuit to re-arm the VDD supply POR circuit, the external VDD supply must be lowered to the natural arming voltage of the POR circuit. • DSWDT time-out. When the DSWDT timer times out, the device exits Deep Sleep. • RTCC alarm (if RTCEN = 1). • Assertion (‘0’) of the MCLR pin. • Assertion of the INT0 pin (if the interrupt was enabled before Deep Sleep mode was entered). The polarity configuration is used to determine the assertion level (‘0’ or ‘1’) of the pin that will cause an exit from Deep Sleep mode. Exiting from Deep Sleep mode requires a change on the INT0 pin while in Deep Sleep mode. Note: Any interrupt pending when entering Deep Sleep mode is cleared. Applications which require critical data to be saved prior to Deep Sleep may use the Deep Sleep General Purpose registers, DSGPR0 and DSGPR1 or data EEPROM (if available). Unlike other SFRs, the contents of these registers are preserved while the device is in Deep Sleep mode. After exiting Deep Sleep, software can restore the data by reading the registers and clearing the RELEASE bit (DSCON). 10.2.4.4 I/O Pins During Deep Sleep During Deep Sleep, the general purpose I/O pins retain their previous states and the Secondary Oscillator (SOSC) will remain running, if enabled. Pins that are configured as inputs (TRISx bit set), prior to entry into Deep Sleep, remain high-impedance during Deep Sleep. Pins that are configured as outputs (TRISx bit clear), prior to entry into Deep Sleep, remain as output pins during Deep Sleep. While in this mode, they continue to drive the output level determined by their corresponding LATx bit at the time of entry into Deep Sleep. Once the device wakes back up, all I/O pins continue to maintain their previous states, even after the device has finished the POR sequence and is executing application code again. Pins configured as inputs during Deep Sleep remain high-impedance and pins configured as outputs continue to drive their previous value. After waking up, the TRIS and LAT registers, and the SOSCEN bit (OSCCON) are reset. If firmware modifies any of these bits or registers, the I/O will not immediately go to the newly configured states. Once the firmware clears the RELEASE bit (DSCON), the I/O pins are “released”. This causes the I/O pins to take the states configured by their respective TRIS and LAT bit values. This means that keeping the SOSC running after waking up requires the SOSCEN bit to be set before clearing RELEASE. If the Deep Sleep BOR (DSBOR) is enabled, and a DSBOR or a true POR event occurs during Deep Sleep, the I/O pins will be immediately released, similar to clearing the RELEASE bit. All previous state information will be lost, including the general purpose DSGPR0 and DSGPR1 contents. If a MCLR Reset event occurs during Deep Sleep, the DSGPRx, DSCON and DSWAKE registers will remain valid, and the RELEASE bit will remain set. The state of the SOSC will also be retained. The I/O pins, however, will be reset to their MCLR Reset state. Since RELEASE is still set, changes to the SOSCEN bit (OSCCON) cannot take effect until the RELEASE bit is cleared. In all other Deep Sleep wake-up cases, application firmware must clear the RELEASE bit in order to reconfigure the I/O pins. Exiting Deep Sleep mode generally does not retain the state of the device and is equivalent to a Power-on Reset (POR) of the device. Exceptions to this include the RTCC (if present), which remains operational through the wake-up, the DSGPRx registers and DSWDT. Wake-up events that occur after Deep Sleep exits but before the POR sequence completes are ignored and are not be captured in the DSWAKE register. The sequence for exiting Deep Sleep mode is: 1. After a wake-up event, the device exits Deep Sleep and performs a POR. The DSEN bit is cleared automatically. Code execution resumes at the Reset vector. To determine if the device exited Deep Sleep, read the Deep Sleep bit, DPSLP (RCON). This bit will be set if there was an exit from Deep Sleep mode. If the bit is set, clear it. Determine the wake-up source by reading the DSWAKE register. Determine if a DSBOR event occurred during Deep Sleep mode by reading the DSBOR bit (DSCON). If application context data has been saved, read it back from the DSGPR0 and DSGPR1 registers. Clear the RELEASE bit (DSCON). 2. 3. 4. 5. 6. 10.2.4.3 Saving Context Data with the DSGPR0/DSGPR1 Registers As exiting Deep Sleep mode causes a POR, most Special Function Registers reset to their default POR values. In addition, because VCORE power is not supplied in Deep Sleep mode, information in data RAM may be lost when exiting this mode.  2011 Microchip Technology Inc. DS39995B-page 129 PIC24FV32KA304 FAMILY 10.2.4.5 Deep Sleep WDT 10.2.4.8 Power-on Resets (PORs) To enable the DSWDT in Deep Sleep mode, program the Configuration bit, DSWDTEN (FDS). The device Watchdog Timer (WDT) need not be enabled for the DSWDT to function. Entry into Deep Sleep mode automatically resets the DSWDT. The DSWDT clock source is selected by the DSWCKSEL Configuration bit (FDS). The postscaler options are programmed by the DSWDTPS Configuration bits (FDS). The minimum time-out period that can be achieved is 2.1 ms and the maximum is 25.7 days. For more details on the FDS Configuration register and DSWDT configuration options, refer to Section 26.0 “Special Features”. VDD voltage is monitored to produce PORs. Since exiting from Deep Sleep functionally looks like a POR, the technique described in Section 10.2.4.7 “Checking and Clearing the Status of Deep Sleep” should be used to distinguish between Deep Sleep and a true POR event. When a true POR occurs, the entire device, including all Deep Sleep logic (Deep Sleep registers: RTCC, DSWDT, etc.) is reset. 10.2.4.9 Summary of Deep Sleep Sequence To review, these are the necessary steps involved in invoking and exiting Deep Sleep mode: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Device exits Reset and begins to execute its application code. If DSWDT functionality is required, program the appropriate Configuration bit. Select the appropriate clock(s) for the DSWDT and RTCC (optional). Enable and configure the DSWDT (optional). Enable and configure the RTCC (optional). Write context data to the DSGPRx registers (optional). Enable the INT0 interrupt (optional). Set the DSEN bit in the DSCON register. Enter Deep Sleep by issuing a PWRSV #SLEEP_MODE command. Device exits Deep Sleep when a wake-up event occurs. The DSEN bit is automatically cleared. Read and clear the DPSLP status bit in RCON, and the DSWAKE status bits. Read the DSGPRx registers (optional). Once all state related configurations are complete, clear the RELEASE bit. Application resumes normal operation. 10.2.4.6 Switching Clocks in Deep Sleep Mode Both the RTCC and the DSWDT may run from either SOSC or the LPRC clock source. This allows both the RTCC and DSWDT to run without requiring both the LPRC and SOSC to be enabled together, reducing power consumption. Running the RTCC from LPRC will result in a loss of accuracy in the RTCC of approximately 5 to 10%. If a more accurate RTCC is required, it must be run from the SOSC clock source. The RTCC clock source is selected with the RTCOSC Configuration bit (FDS). Under certain circumstances, it is possible for the DSWDT clock source to be off when entering Deep Sleep mode. In this case, the clock source is turned on automatically (if DSWDT is enabled), without the need for software intervention. However, this can cause a delay in the start of the DSWDT counters. In order to avoid this delay when using SOSC as a clock source, the application can activate SOSC prior to entering Deep Sleep mode. 10.2.4.7 Checking and Clearing the Status of Deep Sleep Upon entry into Deep Sleep mode, the status bit, DPSLP (RCON), becomes set and must be cleared by the software. On power-up, the software should read this status bit to determine if the Reset was due to an exit from Deep Sleep mode and clear the bit if it is set. Of the four possible combinations of DPSLP and POR bit states, three cases can be considered: • Both the DPSLP and POR bits are cleared. In this case, the Reset was due to some event other than a Deep Sleep mode exit. • The DPSLP bit is clear, but the POR bit is set. This is a normal POR. • Both the DPSLP and POR bits are set. This means that Deep Sleep mode was entered, the device was powered down and Deep Sleep mode was exited. DS39995B-page 130  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 10-1: R/W-0 DSEN bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 C = Clearable bit W = Writable bit ‘1’ = Bit is set HS = Hardware Settable bit U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — R/W-0 ULPWUDIS R/W-0 DSBOR (2) DSCON: DEEP SLEEP CONTROL REGISTER(1) U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0 RTCCWDIS bit 8 R/C-0, HS RELEASE bit 0 — U-0 DSEN: Deep Sleep Enable bit 1 = Enters Deep Sleep on execution of PWRSAV #0 0 = Enters normal Sleep on execution of PWRSAV #0 Unimplemented: Read as ‘0’ RTCCWDIS: RTCC Wake-up Disable bit 1 = Wake-up from Deep Sleep with RTCC disabled 0 = Wake-up from Deep Sleep with RTCC enabled Unimplemented: Read as ‘0’ ULPWUDIS: ULPWU Wake-up Disable bit 1 = Wake-up from Deep Sleep with ULPWU disabled 0 = Wake-up from Deep Sleep with ULPWU enabled DSBOR: Deep Sleep BOR Event bit(2) 1 = The DSBOR was active and a BOR event was detected during Deep Sleep 0 = The DSBOR was not active, or was active but did not detect a BOR event during Deep Sleep RELEASE: I/O Pin State Release bit 1 = Upon waking from Deep Sleep, I/O pins maintain their previous states to Deep Sleep entry 0 = Release I/O pins from their state previous to Deep Sleep entry, and allow their respective TRIS and LAT bits to control their states All register bits are reset only in the case of a POR event outside of Deep Sleep mode. Unlike all other events, a Deep Sleep BOR event will NOT cause a wake-up from Deep Sleep; this re-arms POR. bit 14-9 bit 8 bit 7-3 bit 2 bit 1 bit 0 Note 1: 2:  2011 Microchip Technology Inc. DS39995B-page 131 PIC24FV32KA304 FAMILY REGISTER 10-2: U-0 — bit 15 R/W-0, HS DSFLT bit 7 Legend: R = Readable bit -n = Value at POR bit 15-9 bit 8 HS = Hardware Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — R/W-0, HS DSWDT R/W-0, HS DSRTCC R/W-0, HS DSMCLR U-0 — — DSWAKE: DEEP SLEEP WAKE-UP SOURCE REGISTER(1) U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0, HS DSINT0 bit 8 R/W-0, HS DSPOR(2,3) bit 0 U-0 Unimplemented: Read as ‘0’ DSINT0: Interrupt-on-Change bit 1 = Interrupt-on-change was asserted during Deep Sleep 0 = Interrupt-on-change was not asserted during Deep Sleep DSFLT: Deep Sleep Fault Detect bit 1 = A Fault occurred during Deep Sleep and some Deep Sleep configuration settings may have been corrupted 0 = No Fault was detected during Deep Sleep Unimplemented: Read as ‘0’ DSWDT: Deep Sleep Watchdog Timer Time-out bit 1 = The Deep Sleep Watchdog Timer timed out during Deep Sleep 0 = The Deep Sleep Watchdog Timer did not time out during Deep Sleep DSRTCC: Real-Time Clock and Calendar (RTCC) Alarm bit 1 = The Real-Time Clock and Calendar triggered an alarm during Deep Sleep 0 = The Real-Time Clock and Calendar did not trigger an alarm during Deep Sleep DSMCLR: MCLR Event bit 1 = The MCLR pin was active and was asserted during Deep Sleep 0 = The MCLR pin was not active, or was active, but not asserted during Deep Sleep Unimplemented: Read as ‘0’ DSPOR: Power-on Reset Event bit(2,3) 1 = The VDD supply POR circuit was active and a POR event was detected 0 = The VDD supply POR circuit was not active, or was active but did not detect a POR event All register bits are cleared when the DSEN (DSCON) bit is set. All register bits are reset only in the case of a POR event outside of Deep Sleep mode, except bit, DSPOR, which does not reset on a POR event that is caused due to a Deep Sleep exit. Unlike the other bits in this register, this bit can be set outside of Deep Sleep. bit 7 bit 6-5 bit 4 bit 3 bit 2 bit 1 bit 0 Note 1: 2: 3: DS39995B-page 132  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 10.3 Ultra Low-Power Wake-up EXAMPLE 10-3: The Ultra Low-Power Wake-up (ULPWU) on pin, RB0, allows a slow falling voltage to generate an interrupt without excess current consumption. To use this feature: 1. 2. 3. 4. 5. Charge the capacitor on RB0 by configuring the RB0 pin to an output and setting it to ‘1’. Stop charging the capacitor by configuring RB0 as an input. Discharge the capacitor by setting the ULPEN and ULPSINK bits in the ULPWCON register. Configure Sleep mode. Enter Sleep mode. ULTRA LOW-POWER WAKE-UP INITIALIZATION //******************************* // 1. Charge the capacitor on RB0 //******************************* TRISBbits.TRISB0 = 0; LATBbits.LATB0 = 1; for(i = 0; i < 10000; i++) Nop(); //***************************** //2. Stop Charging the capacitor // on RB0 //***************************** TRISBbits.TRISB0 = 1; //***************************** //3. Enable ULPWU Interrupt //***************************** IFS5bits.ULPWUIF = 0; IEC5bits.ULPWUIE = 1; IPC21bits.ULPWUIP = 0x7; //***************************** //4. Enable the Ultra Low Power // // Wakeup module and allow capacitor discharge When the voltage on RB0 drops below VIL, the device wakes up and executes the next instruction. This feature provides a low-power technique for periodically waking up the device from Sleep mode. The time-out is dependent on the discharge time of the RC circuit on RB0. When the ULPWU module wakes the device from Sleep mode, the ULPWUIF bit (IFS5) is set. Software can check this bit upon wake-up to determine the wake-up source. See Example 10-3 for initializing the ULPWU module //***************************** ULPWCONbits.ULPEN = 1; ULPWCONbit.ULPSINK = 1; //***************************** //5. Enter Sleep Mode //***************************** Sleep(); //for sleep, execution will //resume here A series resistor, between RB0 and the external capacitor, provides overcurrent protection for the RB0/AN0/ULPWU pin and enables software calibration of the time-out (see Figure 10-1). FIGURE 10-1: RB0 SERIAL RESISTOR R1 C1 A timer can be used to measure the charge time and discharge time of the capacitor. The charge time can then be adjusted to provide the desired delay in Sleep. This technique compensates for the affects of temperature, voltage and component accuracy. The peripheral can also be configured as a simple, programmable Low-Voltage Detect (LVD) or temperature sensor.  2011 Microchip Technology Inc. DS39995B-page 133 PIC24FV32KA304 FAMILY REGISTER 10-3: R/W-0 ULPEN bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 0 — ULPWCON: ULPWU CONTROL REGISTER(1) R/W-0 ULPSIDL U-0 — U-0 — U-0 — U-0 — R/W-0 ULPSINK bit 8 U-0 ULPEN: ULPWU Module Enable bit 1 = Module is enabled 0 = Module is disabled Unimplemented: Read as ‘0’ ULPSIDL: ULPWU Stop in Idle Select bit 1 = Discontinue module operation when the device enters Idle mode 0 = Continue module operation in Idle mode Unimplemented: Read as ‘0’ ULPSINK: ULPWU Current Sink Enable bit 1 = Current sink is enabled 0 = Current sink is disabled Unimplemented: Read as ‘0’ bit 14 bit 13 bit 12-9 bit 8 bit 7-0 DS39995B-page 134  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 10.4 Voltage Regulator-Based Power-Saving Features 10.4.3 SLEEP (STANDBY) MODE In Sleep mode, the device is in Sleep and the main HVREG is providing a regulated voltage at a reduced (standby) supply current. This mode provides for limited functionality due to the reduced supply current. It consumes less power than Fast Wake-up Sleep mode, but requires a longer time to wake-up from Sleep. PIC24FV32KA304 series devices have a voltage regulator that has the ability to alter functionality to provide power savings. The on board regulator is made up of two basic modules: the High-Voltage Regulator (HVREG) and the Low-Voltage Regulator (LVREG). With the combination of HVREG and LVREG, the following power modes are available: 10.4.4 LOW-VOLTAGE SLEEP MODE 10.4.1 RUN MODE In Run mode, the main HVREG is providing a regulated voltage with enough current to supply a device running at full speed, and the device is not in Sleep or Deep Sleep Mode. The LVREG may or may not be running, but is unused. 10.4.2 FAST WAKE-UP SLEEP MODE In Fast Wake-up Sleep mode, the device is in Sleep, but the main HVREG is still providing the regulated voltage at full supply current. This mode consumes the most power in Sleep, but provides the fastest wake-up from Sleep. In Low-Voltage Sleep mode, the device is in Sleep and all regulated voltage is provided solely by the LVREG. Consequently, this mode provides the lowest Sleep power consumption, but is also the most limited in terms of how much functionality can be enabled while in this mode. The low-voltage Sleep wake-up time is longer than Sleep mode due to the extra time required to raise the VCORE supply rail back to normal regulated levels. Note: The PIC24F32KA30X family parts do not have any internal voltage regulation, and therefore do not support Low-Voltage Sleep mode. 10.4.5 DEEP SLEEP MODE In Deep Sleep mode, both the main HVREG and LVREG are shut down, providing the lowest possible device power consumption. However, this mode provides no retention or functionality of the device and has the longest wake-up time.  2011 Microchip Technology Inc. DS39995B-page 135 PIC24FV32KA304 FAMILY TABLE 10-1: LVRCFG bit (FPOR) 0 0 VOLTAGE REGULATION CONFIGURATION SETTINGS FOR PIC24FV32KA304 DEVICES LVREN bit (RCON 0 0 PMSLP bit (RCON) 1 0 Power Mode During Sleep Sleep Sleep (Standby) LVREG is unused HVREG goes to Low-Power Standby mode during Sleep LVREG is unused HVREG is off during Sleep LVREG is enabled and provides Sleep voltage regulation LVREG is disabled at all times HVREG goes to Low-Power Standby mode during Sleep LVREG is disabled at all times Description Fast Wake-up HVREG mode (normal) is unchanged during Sleep 0 1 0 Low Voltage Sleep 1 1 X X 1 0 Fast Wake-up HVREG mode (normal) is unchanged during Sleep Sleep Sleep (Standby) DS39995B-page 136  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 10.5 Doze Mode 10.6 Generally, changing clock speed and invoking one of the power-saving modes are the preferred strategies for reducing power consumption. There may be circumstances, however, where this is not practical. For example, it may be necessary for an application to maintain uninterrupted synchronous communication, even while it is doing nothing else. Reducing system clock speed may introduce communication errors, while using a power-saving mode may stop communications completely. Doze mode is a simple and effective alternative method to reduce power consumption while the device is still executing code. In this mode, the system clock continues to operate from the same source and at the same speed. Peripheral modules continue to be clocked at the same speed, while the CPU clock speed is reduced. Synchronization between the two clock domains is maintained, allowing the peripherals to access the SFRs while the CPU executes code at a slower rate. Doze mode is enabled by setting the DOZEN bit (CLKDIV). The ratio between peripheral and core clock speed is determined by the DOZE bits (CLKDIV). There are eight possible configurations, from 1:1 to 1:128, with 1:1 being the default. It is also possible to use Doze mode to selectively reduce power consumption in event driven applications. This allows clock-sensitive functions, such as synchronous communications, to continue without interruption. Meanwhile, the CPU Idles, waiting for something to invoke an interrupt routine. Enabling the automatic return to full-speed CPU operation on interrupts is enabled by setting the ROI bit (CLKDIV). By default, interrupt events have no effect on Doze mode operation. Selective Peripheral Module Control Idle and Doze modes allow users to substantially reduce power consumption by slowing or stopping the CPU clock. Even so, peripheral modules still remain clocked, and thus, consume power. There may be cases where the application needs what these modes do not provide: the allocation of power resources to CPU processing, with minimal power consumption from the peripherals. PIC24F devices address this requirement by allowing peripheral modules to be selectively disabled, reducing or eliminating their power consumption. This can be done with two control bits: • The Peripheral Enable bit, generically named, “XXXEN”, located in the module’s main control SFR. • The Peripheral Module Disable (PMD) bit, generically named, “XXXMD”, located in one of the PMD Control registers. Both bits have similar functions in enabling or disabling its associated module. Setting the PMD bit for a module disables all clock sources to that module, reducing its power consumption to an absolute minimum. In this state, the control and status registers associated with the peripheral will also be disabled, so writes to those registers will have no effect, and read values will be invalid. Many peripheral modules have a corresponding PMD bit. In contrast, disabling a module by clearing its XXXEN bit, disables its functionality, but leaves its registers available to be read and written to. Power consumption is reduced, but not by as much as the PMD bits are used. Most peripheral modules have an enable bit; exceptions include capture, compare and RTCC. To achieve more selective power savings, peripheral modules can also be selectively disabled when the device enters Idle mode. This is done through the control bit of the generic name format, “XXXIDL”. By default, all modules that can operate during Idle mode will do so. Using the disable on Idle feature disables the module while in Idle mode, allowing further reduction of power consumption during Idle mode, enhancing power savings for extremely critical power applications.  2011 Microchip Technology Inc. DS39995B-page 137 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 138  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 11.0 Note: I/O PORTS This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the I/O Ports, refer to the “PIC24F Family Reference Manual”, Section 12. “I/O Ports with Peripheral Pin Select (PPS)” (DS39711). Note that the PIC24FV32KA304 family devices do not support Peripheral Pin Select features. When a peripheral is enabled and the peripheral is actively driving an associated pin, the use of the pin as a general purpose output pin is disabled. The I/O pin may be read, but the output driver for the parallel port bit will be disabled. If a peripheral is enabled, but the peripheral is not actively driving a pin, that pin may be driven by a port. All port pins have three registers directly associated with their operation as digital I/O. The Data Direction register (TRISx) determines whether the pin is an input or an output. If the data direction bit is a ‘1’, then the pin is an input. All port pins are defined as inputs after a Reset. Reads from the Data Latch register (LATx), read the latch. Writes to the latch, write the latch. Reads from the port (PORTx), read the port pins, while writes to the port pins, write the latch. Any bit and its associated data and control registers that are not valid for a particular device will be disabled. That means the corresponding LATx and TRISx registers, and the port pin will read as zeros. When a pin is shared with another peripheral or function that is defined as an input only, it is nevertheless regarded as a dedicated port because there is no other competing source of outputs. Note: The I/O pins retain their state during Deep Sleep. They will retain this state at wake-up until the software restore bit (RELEASE) is cleared. All of the device pins (except VDD and VSS) are shared between the peripherals and the parallel I/O ports. All I/O input ports feature Schmitt Trigger inputs for improved noise immunity. 11.1 Parallel I/O (PIO) Ports A parallel I/O port that shares a pin with a peripheral is, in general, subservient to the peripheral. The peripheral’s output buffer data and control signals are provided to a pair of multiplexers. The multiplexers select whether the peripheral or the associated port has ownership of the output data and control signals of the I/O pin. The logic also prevents “loop through”, in which a port’s digital output can drive the input of a peripheral that shares the same pin. Figure 11-1 illustrates how ports are shared with other peripherals and the associated I/O pin to which they are connected. FIGURE 11-1: BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE Peripheral Module Peripheral Input Data Peripheral Module Enable Peripheral Output Enable Peripheral Output Data I/O 1 0 1 0 Output Enable Output Multiplexers PIO Module Read TRIS Output Data Data Bus WR TRIS D CK Q I/O Pin TRIS Latch D WR LAT + WR PORT CK Data Latch Read LAT Input Data Read PORT Q  2011 Microchip Technology Inc. DS39995B-page 139 PIC24FV32KA304 FAMILY 11.1.1 OPEN-DRAIN CONFIGURATION In addition to the PORT, LAT and TRIS registers for data control, each port pin can also be individually configured for either digital or open-drain output. This is controlled by the Open-Drain Control register, ODCx, associated with each port. Setting any of the bits configures the corresponding pin to act as an open-drain output. The maximum open-drain voltage allowed is the same as the maximum VIH specification. When reading the PORT register, all pins configured as analog input channels will read as cleared (a low level). Analog levels on any pin that is defined as a digital input (including the ANx pins) may cause the input buffer to consume current that exceeds the device specifications. 11.2.1 ANALOG SELECTION REGISTER 11.2 Configuring Analog Port Pins I/O pins with shared analog functionality, such as ADC inputs and comparator inputs, must have their digital inputs shut off when analog functionality is used. Note that analog functionality includes an analog voltage being applied to the pin externally. To allow for analog control, the ANSx registers are provided. There is one ANS register for each port (ANSA, ANSB and ANSC). Within each ANSx register, there is a bit for each pin that shares analog functionality with the digital I/O functionality. If a particular pin does not have an analog function, that bit is unimplemented. See Register 11-1 to Register 11-3 for implementation. The use of the ANS and TRIS registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bit set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. REGISTER 11-1: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-4 bit 3-0 ANSA: ANALOG SELECTION (PORTA) U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 U-0 — U-0 — U-0 — R/W-1 ANSA3 R/W-1 ANSA2 R/W-1 ANSA1 R/W-1 ANSA0 bit 0 U = Unimplemented bit, read as ‘0’ W = Writable bit ‘1’ = Bit is set HSC = Hardware Settable/Clearable bit ‘0’ = Bit is cleared x = Bit is unknown Unimplemented: Read as ‘0’ ANSA: Analog Select Control bits 1 = Digital input buffer is not active (use for analog input) 0 = Digital input buffer is active DS39995B-page 140  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 11-2: R/W-1 ANSB15 bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-12 U = Unimplemented bit, read as ‘0’ W = Writable bit ‘1’ = Bit is set HSC = Hardware Settable/Clearable bit ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — R/W-1 ANSB4 R/W-1 ANSB3(1) R/W-1 ANSB2 R/W-1 ANSB1 ANSB: ANALOG SELECTION (PORTB) R/W-1 ANSB13 R/W-1 ANSB12 U-0 — U-0 — U-0 — U-0 — bit 8 R/W-1 ANSB0 bit 0 R/W-1 ANSB14 ANSB: Analog Select Control bits 1 = Digital input buffer is not active (use for analog input) 0 = Digital input buffer is active Unimplemented: Read as ‘0’ ANSB: Analog Select Control bits 1 = Digital input buffer is not active (use for analog input) 0 = Digital input buffer is active Not available on 20-pin devices. bit 11-5 bit 4-0 Note 1: REGISTER 11-3: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-3 bit 2-0 ANSC ANALOG SELECTION (PORTC) U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 U-0 — U-0 — U-0 — U-0 — R/W-1 ANSC2(1) R/W-1 ANSC1(1) R/W-1 ANSC0(1) bit 0 U = Unimplemented bit, read as ‘0’ W = Writable bit ‘1’ = Bit is set HSC = Hardware Settable/Clearable bit ‘0’ = Bit is cleared x = Bit is unknown Unimplemented: Read as ‘0’ ANSC: Analog Select Control bits 1 = Digital Input Buffer Not Active (Use for Analog Input) 0 = Digital Input Buffer Active Not available on 20-pin or 28-pin devices. Note 1:  2011 Microchip Technology Inc. DS39995B-page 141 PIC24FV32KA304 FAMILY 11.2.2 I/O PORT WRITE/READ TIMING One instruction cycle is required between a port direction change or port write operation and a read operation of the same port. Typically, this instruction would be a NOP. On any pin, only the pull-up resistor or the pull-down resistor should be enabled, but not both of them. If the push button or the keypad is connected to VDD, enable the pull-down, or if they are connected to VSS, enable the pull-up resistors. The pull-ups are enabled separately using the CNPU1 and CNPU2 registers, which contain the control bits for each of the CN pins. Setting any of the control bits enables the weak pull-ups for the corresponding pins. The pull-downs are enabled separately, using the CNPD1 and CNPD2 registers, which contain the control bits for each of the CN pins. Setting any of the control bits enables the weak pull-downs for the corresponding pins. When the internal pull-up is selected, the pin uses VDD as the pull-up source voltage. When the internal pull-down is selected, the pins are pulled down to VSS by an internal resistor. Make sure that there is no external pull-up source/pull-down sink when the internal pull-ups/pull-downs are enabled. Note: Pull-ups and pull-downs on change notification pins should always be disabled whenever the port pin is configured as a digital output. 11.3 Input Change Notification The input change notification function of the I/O ports allows the PIC24FV32KA304 family of devices to generate interrupt requests to the processor in response to a Change-of-State (COS) on selected input pins. This feature is capable of detecting input change of states, even in Sleep mode, when the clocks are disabled. Depending on the device pin count, there are up to 23 external signals (CN0 through CN22) that may be selected (enabled) for generating an interrupt request on a Change-of-State. There are six control registers associated with the CN module. The CNEN1 and CNEN2 registers contain the interrupt enable control bits for each of the CN input pins. Setting any of these bits enables a CN interrupt for the corresponding pins. Each CN pin also has a weak pull-up/pull-down connected to it. The pull-ups act as a current source that is connected to the pin. The pull-downs act as a current sink to eliminate the need for external resistors when push button or keypad devices are connected. EXAMPLE 11-1: MOV MOV NOP; BTSS 0xFF00, W0; W0, TRISB; PORTB, #13; PORT WRITE/READ EXAMPLE //Configure PORTB as inputs and PORTB as outputs //Delay 1 cycle //Next Instruction Equivalent ‘C’ Code TRISB = 0xFF00; NOP(); if(PORTBbits.RB13 == 1) { } //Configure PORTB as inputs and PORTB as outputs //Delay 1 cycle // execute following code if PORTB pin 13 is set. DS39995B-page 142  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 12.0 Note: TIMER1 This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on Timers, refer to the “PIC24F Family Reference Manual”, Section 14. “Timers” (DS39704). Figure 12-1 illustrates a block diagram of the 16-bit Timer1 module. To configure Timer1 for operation: 1. 2. 3. 4. 5. 6. Set the TON bit (= 1). Select the timer prescaler ratio using the TCKPS bits. Set the Clock and Gating modes using the TCS and TGATE bits. Set or clear the TSYNC bit to configure synchronous or asynchronous operation. Load the timer period value into the PR1 register. If interrupts are required, set the interrupt enable bit, T1IE. Use the priority bits, T1IP, to set the interrupt priority. The Timer1 module is a 16-bit timer which can serve as the time counter for the Real-Time Clock (RTC), or operate as a free-running, interval timer/counter. Timer1 can operate in three modes: • 16-bit Timer • 16-bit Synchronous Counter • 16-bit Asynchronous Counter Timer1 also supports these features: • Timer Gate Operation • Selectable Prescaler Settings • Timer Operation During CPU Idle and Sleep modes • Interrupt on 16-bit Period Register Match or Falling Edge of External Gate Signal FIGURE 12-1: 16-BIT TIMER1 MODULE BLOCK DIAGRAM TCKPS SOSCO/ T1CK SOSCEN SOSCI Gate Sync TCY TGATE TON 1x 2 Prescaler 1, 8, 64, 256 01 00 TGATE TCS 1 Set T1IF 0 Reset Q Q D CK 0 TMR1 1 Comparator TSYNC Sync Equal PR1  2011 Microchip Technology Inc. DS39995B-page 143 PIC24FV32KA304 FAMILY REGISTER 12-1: R/W-0 TON bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 TGATE R/W-0 TCKPS1 R/W-0 TCKPS0 U-0 — R/W-0 TSYNC R/W-0 TCS U-0 — bit 0 T1CON: TIMER1 CONTROL REGISTER U-0 — R/W-0 TSIDL U-0 — U-0 — U-0 — R/W-0 T1ECS1(1) R/W-0 T1ECS0(1) bit 8 TON: Timer1 On bit 1 = Starts 16-bit Timer1 0 = Stops 16-bit Timer1 Unimplemented: Read as ‘0’ TSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode Unimplemented: Read as ‘0’ T1ECS : Timer1 Extended Clock Select bits(1) 11 = Reserved; do not use 10 = Timer1 uses LPRC as the clock source 01 = Timer1 uses External Clock from T1CK 00 = Timer1 uses Secondary Oscillator (SOSC) as the clock source Unimplemented: Read as ‘0’ TGATE: Timer1 Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation is enabled 0 = Gated time accumulation is disabled TCKPS: Timer1 Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 Unimplemented: Read as ‘0’ TSYNC: Timer1 External Clock Input Synchronization Select bit When TCS = 1: 1 = Synchronize external clock input 0 = Do not synchronize external clock input When TCS = 0: This bit is ignored. TCS: Timer1 Clock Source Select bit 1 = Timer1 clock source selected by T1ECS 0 = Internal clock (FOSC/2) Unimplemented: Read as ‘0’ The T1ECS bits are valid only when TCS = 1. bit 14 bit 13 bit 12-10 bit 9-8 bit 7 bit 6 bit 5-4 bit 3 bit 2 bit 1 bit 0 Note 1: DS39995B-page 144  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 13.0 Note: TIMER2/3 AND TIMER4/5 This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on Timers, refer to the “PIC24F Family Reference Manual”, Section 14. “Timers” (DS39704). To configure Timer2/3 or Timer4/5 for 32-bit operation: 1. 2. 3. 4. Set the T32 bit (T2CON or T4CON = 1). Select the prescaler ratio for Timer2 or Timer4 using the TCKPS bits. Set the Clock and Gating modes using the TCS and TGATE bits. Load the timer period value. PR3 (or PR5) will contain the most significant word of the value while PR2 (or PR4) contains the least significant word. If interrupts are required, set the interrupt enable bit, TxIE. Use the priority bits, TxIP, to set the interrupt priority. Set the TON bit (TxCON = 1). The Timer2/3 and Timer4/5 modules are 32-bit timers, which can also be configured as four independent,16-bit timers with selectable operating modes. As a 32-bit timer, Timer2/3 or Timer4/5 operate in three modes: • Two independent 16-bit timers (Timer2 and Timer3) with all 16-bit operating modes (except Asynchronous Counter mode) • Single 32-bit timer • Single 32-bit synchronous counter They also support these features: • Timer gate operation • Selectable prescaler settings • Timer operation during Idle and Sleep modes • Interrupt on a 32-bit Period register match • ADC Event Trigger Individually, all four of the 16-bit timers can function as synchronous timers or counters. They also offer the features listed above, except for the ADC event trigger (this is implemented only with Timer3). The operating modes and enabled features are determined by setting the appropriate bit(s) in the T2CON, T3CON, T4CON, and T5CON registers. T2CON,T3CON, T4CON, and T5CON are provided in generic form in Register 13-1 and Register 13-2, respectively. For 32-bit timer/counter operation, Timer2/Timer4 is the least significant word (lsw) and Timer3/Timer5 is the most significant word (msw) of the 32-bit timer. Note: For 32-bit operation, T3CON or T5CON control bits are ignored. Only T2CON or T4CON control bits are used for setup and control. Timer2 or Timer4 clock and gate inputs are utilized for the 32-bit timer modules, but an interrupt is generated with the Timer3 or Timer5 interrupt flags. 5. 6. The timer value, at any point, is stored in the register pair, TMR3:TMR2 (or TMR5:TMR4). TMR3 (TMR5) always contains the most significant word of the count, while TMR2 (TMR4) contains the least significant word. To configure any of the timers for individual 16-bit operation: 1. Clear the T32 bit corresponding to that timer (T2CON for Timer2 and Timer3 or T4CON for Timer4 and Timer5). Select the timer prescaler ratio using the TCKPS bits. Set the Clock and Gating modes using the TCS and TGATE bits. Load the timer period value into the PRx register. If interrupts are required, set the interrupt enable bit, TxIE; use the priority bits, TxIP, to set the interrupt priority. Set the TON bit (TxCON = 1). 2. 3. 4. 5. 6.  2011 Microchip Technology Inc. DS39995B-page 145 PIC24FV32KA304 FAMILY FIGURE 13-1: TIMER2/3 AND TIMER4/5 (32-BIT) BLOCK DIAGRAM TCKPS 2 Prescaler 1, 8, 64, 256 T2CK (T4CK) Gate Sync TCY TGATE TON 1x 01 00 TGATE TCS 1 Set T3IF (T5IF) 0 PR3 (PR5) ADC Event Trigger(2) Equal MSB Reset 16 Read TMR2 (TMR4) (1) Q Q D CK PR2 (PR4) Comparator LSB TMR3 (TMR5) TMR2 (TMR4) Sync Write TMR2 (TMR4)(1) 16 TMR3HLD (TMR5HLD) 16 Data Bus Note 1: 2: The 32-bit Timer Configuration bit, T32, must be set for 32-bit timer/counter operation. All control bits are respective to the T2CON and T4CON registers. The ADC event trigger is available only on Timer2/3 in 32-bit mode and Timer3 in 16-bit mode. DS39995B-page 146  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY FIGURE 13-2: TIMER2 AND TIMER4 (16-BIT SYNCHRONOUS) BLOCK DIAGRAM TCKPS T2CK (T4CK) Gate Sync TGATE TCY 1 Set T2IF (T4IF) 0 Reset Q Q D CK TON 1x Prescaler 1, 8, 64, 256 2 01 00 TCS TGATE TMR2 (TMR4) Sync Equal Comparator PR2 (PR4) FIGURE 13-3: TIMER3 AND TIMER5 (16-BIT ASYNCHRONOUS) BLOCK DIAGRAM TON TCKPS 2 Prescaler 1, 8, 64, 256 T3CK (T5CK) Sync 1x 01 00 TCY Set T3IF (T5IF) 1 0 Reset Q Q D CK TCS TGATE TGATE TMR3 (TMR5) ADC Event Trigger(1) Equal Comparator PR3 (PR5) Note 1: The ADC event trigger is available only on Timer3.  2011 Microchip Technology Inc. DS39995B-page 147 PIC24FV32KA304 FAMILY REGISTER 13-1: R/W-0 TON bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 TGATE R/W-0 TCKPS1 R/W-0 TCKPS0 R/W-0 T32 (1) TxCON: TIMER2 AND TIMER4 CONTROL REGISTER U-0 — R/W-0 TSIDL U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 U-0 — R/W-0 TCS U-0 — bit 0 TON: Timer2 On bit When TxCON = 1: 1 = Starts 32-bit Timerx/y 0 = Stops 32-bit Timerx/y When TxCON = 0: 1 = Starts 16-bit Timerx 0 = Stops 16-bit Timerx Unimplemented: Read as ‘0’ TSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode Unimplemented: Read as ‘0’ TGATE: Timerx Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation is enabled 0 = Gated time accumulation is disabled TCKPS: Timerx Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 T32: 32-Bit Timer Mode Select bit(1) 1 = Timer2 and Timer3 or Timer4 and Timer5 form a single 32-bit timer 0 = Timer2 and Timer3 or Timer4 and Timer5 act as two 16-bit timers Unimplemented: Read as ‘0’ TCS: Timerx Clock Source Select bit 1 = External clock from pin, TxCK (on the rising edge) 0 = Internal clock (FOSC/2) Unimplemented: Read as ‘0’ In 32-bit mode, the T3CON or T5CON control bits do not affect 32-bit timer operation. bit 14 bit 13 bit 12-7 bit 6 bit 5-4 bit 3 bit 2 bit 1 bit 0 Note 1: DS39995B-page 148  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 13-2: R/W-0 TON(1) bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 TGATE(1) R/W-0 TCKPS1(1) R/W-0 TCKPS0(1) U-0 — U-0 — R/W-0 TCS(1) U-0 — bit 0 TyCON: TIMER3 AND TIMER5 CONTROL REGISTER U-0 — R/W-0 TSIDL(1) U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 TON: Timery On bit(1) 1 = Starts 16-bit Timery 0 = Stops 16-bit Timery Unimplemented: Read as ‘0’ TSIDL: Stop in Idle Mode bit(1) 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode Unimplemented: Read as ‘0’ TGATE: Timery Gated Time Accumulation Enable bit(1) When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation is enabled 0 = Gated time accumulation is disabled TCKPS: Timery Input Clock Prescale Select bits(1) 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 Unimplemented: Read as ‘0’ TCS: Timery Clock Source Select bit(1) 1 = External clock from the T3CK pin (on the rising edge) 0 = Internal clock (FOSC/2) Unimplemented: Read as ‘0’ When 32-bit operation is enabled (TxCON = 1), these bits have no effect on Timery operation. All timer functions are set through TxCON. bit 14 bit 13 bit 12-7 bit 6 bit 5-4 bit 3-2 bit 1 bit 0 Note 1:  2011 Microchip Technology Inc. DS39995B-page 149 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 150  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 14.0 Note: INPUT CAPTURE WITH DEDICATED TIMERS This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information, refer to the “PIC24F Family Reference Manual”, Section 34. “Input Capture with Dedicated Timer” (DS39722). 14.1 14.1.1 General Operating Modes SYNCHRONOUS AND TRIGGER MODES All devices in the PIC24FV32KA304 family features 3 independent input capture modules. Each of the modules offers a wide range of configuration and operating options for capturing external pulse events and generating interrupts. Key features of the input capture module include: • Hardware-configurable for 32-bit operation in all modes by cascading two adjacent modules • Synchronous and Trigger modes of output compare operation, with up to 20 user-selectable trigger/sync sources available • A 4-level FIFO buffer for capturing and holding timer values for several events • Configurable interrupt generation • Up to 6 clock sources available for each module, driving a separate internal 16-bit counter The module is controlled through two registers: ICxCON1 (Register 14-1) and ICxCON2 (Register 14-2). A general block diagram of the module is shown in Figure 14-1. By default, the input capture module operates in a free-running mode. The internal 16-bit counter, ICxTMR, counts up continuously, wrapping around from FFFFh to 0000h on each overflow, with its period synchronized to the selected external clock source. When a capture event occurs, the current 16-bit value of the internal counter is written to the FIFO buffer. In Synchronous mode, the module begins capturing events on the ICx pin as soon as its selected clock source is enabled. Whenever an event occurs on the selected sync source, the internal counter is reset. In Trigger mode, the module waits for a Sync event from another internal module to occur before allowing the internal counter to run. Standard, free-running operation is selected by setting the SYNCSEL bits to ‘00000’ and clearing the ICTRIG bit (ICxCON2). Synchronous and Trigger modes are selected any time the SYNCSEL bits are set to any value except ‘00000’. The ICTRIG bit selects either Synchronous or Trigger mode; setting the bit selects Trigger mode operation. In both modes, the SYNCSEL bits determine the sync/trigger source. When the SYNCSEL bits are set to ‘00000’ and ICTRIG is set, the module operates in Software Trigger mode. In this case, capture operations are started by manually setting the TRIGSTAT bit (ICxCON2). FIGURE 14-1: INPUT CAPTURE BLOCK DIAGRAM ICM ICI Event and Interrupt Logic Set ICxIF ICx Pin Prescaler Counter 1:1/4/16 ICTSEL Edge Detect Logic and Clock Synchronizer IC Clock Sources Clock Select Increment ICxTMR 16 4-Level FIFO Buffer 16 Trigger and Sync Logic Trigger and Sync Sources Reset 16 ICxBUF SYNCSEL Trigger ICOV, ICBNE System Bus  2011 Microchip Technology Inc. DS39995B-page 151 PIC24FV32KA304 FAMILY 14.1.2 CASCADED (32-BIT) MODE By default, each module operates independently with its own 16-bit timer. To increase resolution, adjacent even and odd modules can be configured to function as a single 32-bit module. (For example, Modules 1 and 2 are paired, as are Modules 3 and 4, and so on.) The odd-numbered module (ICx) provides the Least Significant 16 bits of the 32-bit register pairs, and the even module (ICy) provides the Most Significant 16 bits. Wrap arounds of the ICx registers cause an increment of their corresponding ICy registers. Cascaded operation is configured in hardware by setting the IC32 bit (ICxCON2) for both modules. For 32-bit cascaded operations, the setup procedure is slightly different: 1. Set the IC32 bits for both modules (ICyCON2 and (ICxCON2), enabling the even-numbered module first. This ensures the modules will start functioning in unison. Set the ICTSEL and SYNCSEL bits for both modules to select the same sync/trigger and time base source. Set the even module first, then the odd module. Both modules must use the same ICTSEL and SYNCSEL settings. Clear the ICTRIG bit of the even module (ICyCON2). This forces the module to run in Synchronous mode with the odd module, regardless of its trigger setting. Use the odd module’s ICI bits (ICxCON1) to the desired interrupt frequency. Use the ICTRIG bit of the odd module (ICxCON2) to configure Trigger or Synchronous mode operation. Note: For Synchronous mode operation, enable the sync source as the last step. Both input capture modules are held in Reset until the sync source is enabled. 2. 3. 14.2 Capture Operations 4. 5. The input capture module can be configured to capture timer values and generate interrupts on rising edges on ICx, or all transitions on ICx. Captures can be configured to occur on all rising edges or just some (every 4th or 16th). Interrupts can be independently configured to generate on each event or a subset of events. To set up the module for capture operations: 1. 2. If Synchronous mode is to be used, disable the sync source before proceeding. Make sure that any previous data has been removed from the FIFO by reading ICxBUF until the ICBNE bit (ICxCON1) is cleared. Set the SYNCSEL bits (ICxCON2) to the desired sync/trigger source. Set the ICTSEL bits (ICxCON1) for the desired clock source. If the desired clock source is running, set the ICTSEL bits before the input capture module is enabled for proper synchronization with the desired clock source. Set the ICI bits (ICxCON1) to the desired interrupt frequency. Select Synchronous or Trigger mode operation: a) Check that the SYNCSEL bits are not set to ‘00000’. b) For Synchronous mode, clear the ICTRIG bit (ICxCON2). c) For Trigger mode, set ICTRIG and clear the TRIGSTAT bit (ICxCON2). Set the ICM bits (ICxCON1) to the desired operational mode. Enable the selected trigger/sync source. 6. Use the ICM bits of the odd module (ICxCON1) to set the desired capture mode. 3. 4. The module is ready to capture events when the time base and the trigger/sync source are enabled. When the ICBNE bit (ICxCON1) becomes set, at least one capture value is available in the FIFO. Read input capture values from the FIFO until the ICBNE clears to ‘0’. For 32-bit operation, read both the ICxBUF and ICyBUF for the full 32-bit timer value (ICxBUF for the lsw, ICyBUF for the msw). At least one capture value is available in the FIFO buffer when the odd module’s ICBNE bit (ICxCON1) becomes set. Continue to read the buffer registers until ICBNE is cleared (performed automatically by hardware). 5. 6. 7. 8. DS39995B-page 152  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 14-1: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-14 bit 13 HCS = Hardware Clearable/Settable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 ICI1 R/W-0 ICI0 R-0, HCS ICOV R-0, HCS ICBNE R/W-0 ICM2(1) R/W-0 ICM1(1) ICxCON1: INPUT CAPTURE x CONTROL REGISTER 1 U-0 — R/W-0 ICSIDL R/W-0 ICTSEL2 R/W-0 ICTSEL1 R/W-0 ICTSEL0 U-0 — U-0 — bit 8 R/W-0 ICM0(1) bit 0 Unimplemented: Read as ‘0’ ICSIDL: Input Capture x Module Stop in Idle Control bit 1 = Input capture module halts in CPU Idle mode 0 = Input capture module continues to operate in CPU Idle mode ICTSEL: Input Capture Timer Select bits 111 = System clock (FOSC/2) 110 = Reserved 101 = Reserved 100 = Timer1 011 = Timer5 010 = Timer4 001 = Timer2 000 = Timer3 Unimplemented: Read as ‘0’ ICI: Select Number of Captures per Interrupt bits 11 = Interrupt on every fourth capture event 10 = Interrupt on every third capture event 01 = Interrupt on every second capture event 00 = Interrupt on every capture event ICOV: Input Capture x Overflow Status Flag bit (read-only) 1 = Input capture overflow occurred 0 = No input capture overflow occurred ICBNE: Input Capture x Buffer Empty Status bit (read-only) 1 = Input capture buffer is not empty, at least one more capture value can be read 0 = Input capture buffer is empty ICM: Input Capture Mode Select bits(1) 111 = Interrupt mode: input capture functions as interrupt pin only when device is in Sleep or Idle mode (rising edge detect only, all other control bits are not applicable) 110 = Unused (module disabled) 101 = Prescaler Capture mode: capture on every 16th rising edge 100 = Prescaler Capture mode: capture on every 4th rising edge 011 = Simple Capture mode: capture on every rising edge 010 = Simple Capture mode: capture on every falling edge 001 = Edge Detect Capture mode: capture on every edge (rising and falling); ICI 7, or 16 when PLEN 7. CRCFUL: FIFO Full bit 1 = FIFO is full 0 = FIFO is not full CRCMPT: FIFO Empty Bit 1 = FIFO is empty 0 = FIFO is not empty CRCISEL: CRC interrupt Selection bit 1 = Interrupt on FIFO is empty; CRC calculation is not complete 0 = Interrupt on shift is complete and CRCWDAT result is ready CRCGO: Start CRC bit 1 = Start CRC serial shifter 0 = CRC serial shifter is turned off LENDIAN: Data Shift Direction Select bit 1 = Data word is shifted into the CRC, starting with the LSb (little endian) 0 = Data word is shifted into the CRC, starting with the MSb (big endian) Unimplemented: Read as ‘0’ bit 14 bit 13 bit 12-8 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2-0 DS39995B-page 206  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 20-2: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-13 bit 12-8 bit 7-5 bit 4-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — R/W-0 PLEN4 R/W-0 PLEN3 R/W-0 PLEN2 R/W-0 PLEN1 CRCCON2: CRC CONTROL REGISTER 2 U-0 — U-0 — R/W-0 DWIDTH4 R/W-0 DWIDTH3 R/W-0 DWIDTH2 R/W-0 DWIDTH1 R/W-0 DWIDTH0 bit 8 R/W-0 PLEN0 bit 0 Unimplemented: Read as ‘0’ DWIDTH: Data Width Select bits Defines the width of the data word (Data Word Width = (DWIDTH) + 1). Unimplemented: Read as ‘0’ PLEN: Polynomial Length Select bits Defines the length of the CRC polynomial (Polynomial Length = (PLEN) + 1). REGISTER 20-3: R/W-0 X15 bit 15 R/W-0 X7 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-1 bit 0 CRCXORL: CRC XOR POLYNOMIAL REGISTER, LOW BYTE R/W-0 X13 R/W-0 X12 R/W-0 X11 R/W-0 X10 R/W-0 X9 R/W-0 X8 bit 8 X14 R/W-0 R/W-0 X6 R/W-0 X5 R/W-0 X4 R/W-0 X3 R/W-0 X2 R/W-0 X1 U-0 — bit 0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown X: XOR of Polynomial Term Xn Enable bits Unimplemented: Read as ‘0’  2011 Microchip Technology Inc. DS39995B-page 207 PIC24FV32KA304 FAMILY REGISTER 20-4: R/W-0 X31 bit 15 R/W-0 X23 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 X22 R/W-0 X21 R/W-0 X20 R/W-0 X19 R/W-0 X18 R/W-0 X17 CRCXORH: CRC XOR POLYNOMIAL REGISTER, HIGH BYTE R/W-0 X29 R/W-0 X28 R/W-0 X27 R/W-0 X26 R/W-0 X25 R/W-0 X24 bit 8 R/W-0 X16 bit 0 X30 R/W-0 X: XOR of Polynomial Term Xn Enable bits DS39995B-page 208  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 21.0 Note: HIGH/LOW-VOLTAGE DETECT (HLVD) This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the High/Low-Voltage Detect, refer to the “PIC24F Family Reference Manual”, Section 36. “High-Level Integration with Programmable High/Low-Voltage Detect (HLVD)” (DS39725). An interrupt flag is set if the device experiences an excursion past the trip point in the direction of change. If the interrupt is enabled, the program execution will branch to the interrupt vector address and the software can then respond to the interrupt. The HLVD Control register (see Register 21-1) completely controls the operation of the HLVD module. This allows the circuitry to be “turned off” by the user under software control, which minimizes the current consumption for the device. The High/Low-Voltage Detect module (HLVD) is a programmable circuit that allows the user to specify both the device voltage trip point and the direction of change. FIGURE 21-1: HIGH/LOW-VOLTAGE DETECT (HLVD) MODULE BLOCK DIAGRAM VDD Externally Generated Trip Point HLVDIN VDD HLVDL HLVDEN 16-to-1 MUX VDIR - Set HLVDIF Internal Voltage Reference 1.024V Typical HLVDEN  2011 Microchip Technology Inc. DS39995B-page 209 PIC24FV32KA304 FAMILY REGISTER 21-1: R/W-0 HLVDEN bit 15 R/W-0 VDIR bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 BGVST R/W-0 IRVST U-0 — R/W-0 HLVDL3 R/W-0 HLVDL2 R/W-0 HLVDL1 HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER U-0 — R/W-0 HLSIDL U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 HLVDL0 bit 0 HLVDEN: High/Low-Voltage Detect Power Enable bit 1 = HLVD is enabled 0 = HLVD is disabled Unimplemented: Read as ‘0’ HLSIDL: HLVD Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode Unimplemented: Read as ‘0’ VDIR: Voltage Change Direction Select bit 1 = Event occurs when voltage equals or exceeds trip point (HLVDL) 0 = Event occurs when voltage equals or falls below trip point (HLVDL) BGVST: Band Gap Voltage Stable Flag bit 1 = Indicates that the band gap voltage is stable 0 = Indicates that the band gap voltage is unstable IRVST: Internal Reference Voltage Stable Flag bit 1 = Indicates that the internal reference voltage is stable and the high-voltage detect logic generates the interrupt flag at the specified voltage range 0 = Indicates that the internal reference voltage is unstable and the high-voltage detect logic will not generate the interrupt flag at the specified voltage range, and the HLVD interrupt should not be enabled Unimplemented: Read as ‘0’ HLVDL: High/Low-Voltage Detection Limit bits 1111 = External analog input is used (input comes from the HLVDIN pin) 1110 = Trip point 1(1) 1101 = Trip point 2(1) 1100 = Trip point 3(1) . . . 0000 = Trip point 15(1) For the actual trip point, see Section 29.0 “Electrical Characteristics”. bit 14 bit 13 bit 12-8 bit 7 bit 6 bit 5 bit 4 bit 3-0 Note 1: DS39995B-page 210  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 22.0 Note: 12-BIT A/D CONVERTER WITH THRESHOLD DETECT This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the 12-Bit A/D Converter with Threshold Detect, refer to the “PIC24F Family Reference Manual”, Section 51. “12-Bit A/D Converter with Threshold Detect” (DS39739). The 12-bit A/D Converter module is an enhanced version of the 10-bit module offered in some PIC24 devices. Both modules are Successive Approximation Register (SAR) converters at their cores, surrounded by a range of hardware features for flexible configuration. This version of the module extends functionality by providing 12-bit resolution, a wider range of automatic sampling options and tighter integration with other analog modules, such as the CTMU and a configurable results buffer. This module also includes a unique Threshold Detect feature that allows the module itself to make simple decisions based on the conversion results. A simplified block diagram for the module is illustrated in Figure 22-1. The PIC24F 12-bit A/D Converter has the following key features: • Successive Approximation Register (SAR) Conversion • Conversion Speeds of up to 100 ksps • Up to 32 Analog Input Channels (Internal and External) • Multiple Internal Reference Input Channels • External Voltage Reference Input Pins • Unipolar Differential Sample-and-Hold (S/H) Amplifier • Automated Threshold Scan and Compare Operation to Pre-Evaluate Conversion Results • Selectable Conversion Trigger Source • Fixed-Length (one word per channel), Configurable Conversion Result Buffer • Four Options for Results Alignment • Configurable Interrupt Generation • Operation During CPU Sleep and Idle modes  2011 Microchip Technology Inc. DS39995B-page 211 PIC24FV32KA304 FAMILY FIGURE 22-1: 12-BIT A/D CONVERTER BLOCK DIAGRAM Internal Data Bus AVDD VR Select AVSS VREF+ VREFVBG VINH AN0 AN1 AN2 AN3 AN4 AN5 MUX A AN6 AN7 AN8 AN9 VINL VINH Data Formatting 12-Bit SAR Conversion Logic VINL S/H VRVR+ VR+ 16 VRComparator DAC ADC1BUF0: ADC1BUF17 AD1CON1 AD1CON2 AD1CON3 AD1CON5 AD1CHS AD1CHITL AN14 AN15 CTMU Temp. Sensor CTMU VBG 0.785 * VDD 0.215 * VDD AVDD AVss MUX B VINH AD1CHITH AD1CSSL AD1CSSH VINL Sample Control Input MUX Control Pin Config. Control Control Logic Conversion Control DS39995B-page 212  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY To perform an A/D conversion: 1. Configure the A/D module: a) Configure port pins as analog inputs and/or select band gap reference inputs (ANS, ANS). b) Select voltage reference source to match expected range on analog inputs (AD1CON2). c) Select the analog conversion clock to match the desired data rate with the processor clock (AD1CON3). d) Select the appropriate sample/conversion sequence (AD1CON1 and AD1CON3). e) Select how conversion results are presented in the buffer (AD1CON1). f) Select interrupt rate (AD1CON2). g) Turn on A/D module (AD1CON1). Configure A/D interrupt (if required): a) Clear the AD1IF bit. b) Select A/D interrupt priority. a) b) Enable auto-scan (ASEN bit (AD1CON)). Select the Compare mode “Greater Than, Less Than or Windowed” (CM bits (AD1CON5)). Select the threshold compare channels to be scanned (ADCSSH, ADCSSL). If the CTMU is required as a current source for a threshold compare channel, enable the corresponding CTMU channel (ADCCTMUENH, ADCCTMUENL). Write the threshold values into the corresponding ADC1BUFn registers. Turn on the A/D module (AD1CON1). If performing an A/D sample and conversion using Threshold Detect in Sleep Mode, the RC A/D clock source must be selected before entering into Sleep mode. c) d) e) f) Note: 2. 3. Configure A/D interrupt (OPTIONAL): a) Clear the AD1IF bit. b) Select A/D interrupt priority. To perform an A/D sample and conversion using Threshold Detect scanning: 1. Configure the A/D module: a) Configure port pins as analog inputs (ANS, ANS). b) Select voltage reference source to match expected range on analog inputs (AD1CON2). c) Select the analog conversion clock to match the desired data rate with the processor clock (AD1CON3). d) Select the appropriate sample/conversion sequence (AD1CON1, AD1CON3). e) Select how the conversion results are presented in the buffer (AD1CON1). f) Select interrupt rate (AD1CON2). Configure the Threshold compare channels: 2.  2011 Microchip Technology Inc. DS39995B-page 213 PIC24FV32KA304 FAMILY 22.1 A/D Control Registers The 12-bit A/D Converter module uses up to 43 registers for its operation. All registers are mapped in the data memory space. indicate if a match condition has occurred. AD1CHITL is always implemented, whereas AD1CHITH may not be implemented in devices with 16 or fewer channels. The AD1CSSH/L registers (Register 22-8 and Register 22-9) select the channels to be included for sequential scanning. The AD1CTMENH/L registers (Register 22-10 and Register 22-11) select the channel(s) to be used by the CTMU during conversions. Selecting a particular channel allows the A/D Converter to control the CTMU (particularly, its current source) and read its data through that channel. AD1CTMENL is always implemented, whereas AD1CTMENH may not be implemented in devices with 16 or fewer channels. 22.1.1 CONTROL REGISTERS Depending on the specific device, the module has up to eleven control and status registers: • • • • • • AD1CON1: A/D Control Register 1 AD1CON2: A/D Control Register 2 AD1CON3: A/D Control Register 3 AD1CON5: A/D Control Register 5 AD1CHS: A/D Sample Select Register AD1CHITH and AD1CHITL: A/D Scan Compare Hit Registers • AD1CSSL and AD1CSSH: A/D Input Scan Select Registers • AD1CTMENH and AD1CTMENL: CTMU Enable Registers The AD1CON1, AD1CON2 and AD1CON3 registers (Register 22-1, Register 22-2 and Register 22-3) control the overall operation of the A/D module. This includes enabling the module, configuring the conversion clock and voltage reference sources, selecting the sampling and conversion triggers, and manually controlling the sample/convert sequences. The AD1CON5 register (Register 22-4) specifically controls features of the Threshold Detect operation, including its function in power-saving modes. The AD1CHS register (Register 22-5) selects the input channels to be connected to the S/H amplifier. It also allows the choice of input multiplexers and the selection of a reference source for differential sampling. The AD1CHITH and AD1CHITL registers (Register 22-6 and Register 22-7) are semaphore registers used with Threshold Detect operations. The status of individual bits, or bit pairs in some cases, 22.1.2 A/D RESULT BUFFERS The module incorporates a multi-word, dual port RAM, called ADC1BUF. The buffer is composed of at least the same number of word locations as there are external analog channels for a particular device, with a maximum number of 32. The number of buffer addresses is always even. Each of the locations is mapped into the data memory space and is separately addressable. The buffer locations are referred to as ADC1BUF0 through ADC1BUFn (up to 31). The A/D result buffers are both readable and writable. When the module is active (AD1CON = 1), the buffers are read-only, and store the results of A/D conversions. When the module is inactive (AD1CON = 0), the buffers are both readable and writable. In this state, writing to a buffer location programs a conversion threshold for Threshold Detect operations. Buffer contents are not cleared when the module is deactivated with the ADON bit (AD1CON1). Conversion results and any programmed threshold values are maintained when ADON is set or cleared. DS39995B-page 214  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 22-1: R/W-0 ADON bit 15 R/W-0 SSRC3 bit 7 Legend: C = Clearable bit R = Readable bit -n = Value at POR bit 15 U = Unimplemented bit, read as ‘0’ r = Reserved bit W = Writable bit ‘1’ = Bit is set HSC = Hardware Settable/Clearable bit ‘0’ = Bit is cleared x = Bit is unknown R/W-0 SSRC2 R/W-0 SSRC1 R/W-0 SSRC0 U-0 — R/W-0 ASAM R/W-0 HSC SAMP AD1CON1: A/D CONTROL REGISTER 1 U-0 — R/W-0 ADSIDL U-0 — U-0 — r-0 — R/W-0 FORM1 R/W-0 FORM0 bit 8 R/C-0 HSC DONE bit 0 ADON: A/D Operating Mode bit 1 = A/D Converter module is operating 0 = A/D Converter is off Unimplemented: Read as ‘0’ ADSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode Unimplemented: Read as ‘0’ Reserved: Maintain as ‘1’ FORM: Data Output Format bits (see formats following) 11 = Fractional result, signed, left-justified 10 = Absolute fractional result, unsigned, left-justified 01 = Decimal result, signed, right-justified 00 = Absolute decimal result, unsigned, right-justified SSRC: Sample Clock Source Select bits 1111 = Not available; do not use    bit 14 bit 13 bit 12-11 bit 10 bit 9-8 bit 7-4 1000 = Not available; do not use 0111 = Internal counter ends sampling and starts conversion (auto-convert) 0110 = Not Available; do not use 0101 = Timer1 event ends sampling and starts conversion 0100 = CTMU event ends sampling and starts conversion 0011 = Timer5 event ends sampling and starts conversion 0010 = Timer3 event ends sampling and starts conversion 0001 = INT0 event ends sampling and starts conversion 0000 = Clearing the SAMP bit in software ends sampling and begins conversion bit 3 bit 2 Unimplemented: Read as ‘0’ ASAM: A/D Sample Auto-Start bit 1 = Sampling begins immediately after last conversion; SAMP bit is auto-set 0 = Sampling begins when SAMP bit is manually set SAMP: A/D Sample Enable bit 1 = A/D Sample-and-Hold amplifiers are sampling 0 = A/D Sample-and-Hold are holding DONE: A/D Conversion Status bit 1 = A/D conversion cycle is completed 0 = A/D conversion cycle is not started or in progress bit 1 bit 0  2011 Microchip Technology Inc. DS39995B-page 215 PIC24FV32KA304 FAMILY REGISTER 22-2: R/W-0 PVCFG1 bit 15 R/W-0 BUFS(1) bit 7 Legend: R = Readable bit -n = Value at POR bit 15-14 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 SMPI4 R/W-0 SMPI3 R/W-0 SMPI2 R/W-0 SMPI1 R/W-0 SMPI0 R/W-0 BUFM(1) AD1CON2: A/D CONTROL REGISTER 2 R/W-0 NVCFG0 R/W-0 OFFCAL R/W-0 BUFREGEN R/W-0 CSCNA U-0 — U-0 — bit 8 R/W-0 ALTS bit 0 R/W-0 PVCFG0 PVCFG: Converter Positive Voltage Reference Configuration bits 11 = Internal VRH2 10 = Internal VRH1 01 = External VREF+ 00 = AVDD NVCFG0: Converter Negative Voltage Reference Configuration bits 1 = External VREF0 = AVSS OFFCAL: Offset Calibration Mode Select bit 1 = Inverting and non-inverting inputs of channel Sample-and-Hold are connected to AVSS 0 = Inverting and non-inverting inputs of channel Sample-and-Hold are connected to normal inputs BUFREGEN: A/D Buffer Register Enable bit 1 = Conversion result is loaded into buffer location determined by the converted channel 0 = A/D result buffer is treated as a FIFO CSCNA: Scan Input Selections for CH0+ During SAMPLE A bit 1 = Scan inputs 0 = Do not scan inputs Unimplemented: Read as ‘0’ BUFS: Buffer Fill Status bit(1) 1 = A/D is filling the upper half of the buffer; user should access data in the lower half 0 = A/D is filling the lower half of the buffer; user should access data in the upper half SMPI: Interrupt Sample Rate Select bits 11111 = Interrupts at the completion of conversion for each 32nd sample 11110 = Interrupts at the completion of conversion for each 31st sample    bit 13 bit 12 bit 11 bit 10 bit 9-8 bit 7 bit 6-2 00001 = Interrupts at the completion of conversion for every other sample 00000 = Interrupts at the completion of conversion for each sample bit 1 BUFM: Buffer Fill Mode Select bit(1) 1 = Starts buffer filling at AD1BUF0 on first interrupt and AD1BUF(n/2) on next interrupt (Split Buffer mode) 0 = Starts filling buffer at address, ADCBUF0, and each sequential address on successive interrupts (FIFO mode) ALTS: Alternate Input Sample Mode Select bit 1 = Uses channel input selects for SAMPLE A on first sample and SAMPLE B on next sample 0 = Always uses channel input selects for SAMPLE A Only applicable when the buffer is used in FIFO mode (BUFREGEN = 0). In addition, BUFS is only used when BUFM = 1. bit 0 Note 1: DS39995B-page 216  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 22-3: R/W-0 ADRC bit 15 R/W-0 ADCS7 bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 ADCS6 R/W-0 ADCS5 R/W-0 ADCS4 R/W-0 ADCS3 R/W-0 ADCS2 R/W-0 ADCS1 AD1CON3: A/D CONTROL REGISTER 3 R-0 U-0 — R/W-0 SAMC4 R/W-0 SAMC3 R/W-0 SAMC2 R/W-0 SAMC1 R/W-0 SAMC0 bit 8 R/W-0 ADCS0 bit 0 EXTSAM ADRC: A/D Conversion Clock Source bit 1 = RC clock 0 = Clock derived from system clock EXTSAM: Extended Sampling Time bit 1 = A/D is still sampling after SAMP = 0 0 = A/D is finished sampling Reserved: Maintain as ‘0’ SAMC: Auto-Sample Time Select bits 11111 = 31 TAD    bit 14 bit 13 bit 12-8 00001 = 1 TAD 00000 = 0 TAD bit 7-0 ADCS: A/D Conversion Clock Select bits 11111111-01000000 = Reserved 00111111 = 64·TCY = TAD    00000001 = 2·TCY = TAD 00000000 = TCY = TAD  2011 Microchip Technology Inc. DS39995B-page 217 PIC24FV32KA304 FAMILY REGISTER 22-4: R/W-0 ASEN bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — R/W-0 WM1 R/W-0 WM0 R/W-0 CM1 AD1CON5: A/D CONTROL REGISTER 5 R/W-0 CTMREQ R/W-0 BGREQ R/W-0 VRSREQ U-0 — R/W-0 ASINT1 R/W-0 ASINT0 bit 8 R/W-0 CM0 bit 0 R/W-0 LPEN ASEN: Auto-Scan Enable bit 1 = Auto-scan is enabled 0 = Auto-scan is disabled LPEN: Low-Power Enable bit 1 = Return to Low-Power mode after scan 0 = Remain in Full-Power mode after scan CTMREQ: CTMU Request bit 1 = CTMU is enabled when the ADC is enabled and active 0 = CTMU is not enabled by the ADC BGREQ: Band Gap Request bit 1 = Band gap is enabled when the ADC is enabled and active 0 = Band gap is not enabled by the ADC VRSREQ: VREG Scan Request bit 1 = On-chip regulator is enabled when the ADC is enabled and active 0 = On-chip regulator is not enabled by the ADC Unimplemented: Read as ‘0’ ASINT: Auto-Scan (Threshold Detect) Interrupt Mode bits 11 = Interrupt after Threshold Detect sequence completed and valid compare has occurred 10 = Interrupt after valid compare has occurred 01 = Interrupt after Threshold Detect sequence completed 00 = No interrupt Unimplemented: Read as ‘0’ WM: Write Mode bits 11 = Reserved 10 = Auto-compare only (conversion results are not saved, but interrupts are generated when a valid match, as defined by CM and ASINT bits, occurs) 01 = Convert and save (conversion results are saved to locations as determined by register bits when a match, as defined by CM bits, occurs) 00 = Legacy operation (conversion data saved to location determined by buffer register bits) CM: Compare Mode bits 11 = Outside Window mode (valid match occurs if the conversion result is outside of the window defined by the corresponding buffer pair) 10 = Inside Window mode (valid match occurs if the conversion result is inside the window defined by the corresponding buffer pair) 01 = Greater Than mode (valid match occurs if the result is greater than value in the corresponding buffer register) 00 = Less Than mode (valid match occurs if the result is less than value in the corresponding buffer register) bit 14 bit 13 bit 12 bit 11 bit 10 bit 9-8 bit 7-4 bit 3-2 bit 1-0 DS39995B-page 218  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 22-5: R/W-0 CH0NB2 bit 15 R/W-0 CH0NA2 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-13 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 CH0NA1 R/W-0 CH0NA0 R/W-0 CH0SA4 R/W-0 CH0SA3 R/W-0 CH0SA2 R/W-0 CH0SA1 AD1CHS: A/D SAMPLE SELECT REGISTER R/W-0 CH0NB0 R/W-0 CH0SB4 R/W-0 CH0SB3 R/W-0 CH0SB2 R/W-0 CH0SB1 R/W-0 CH0SB0 bit 8 R/W-0 CH0SA0 bit 0 R/W-0 CH0NB1 CH0NB: Sample B Channel 0 Negative Input Select bits 111 = AN6(1) 110 = AN5(2) 101 = AN4 100 = AN3 011 = AN2 010 = AN1 001 = AN0 000 = AVSS CH0SB: S/H Amplifier Positive Input Select for MUX B Multiplexer Setting bits 11111 = Unimplemented, do not use 11101 = AVDD(3) 11101 = AVSS(3) 11100 = Upper guardband rail (0.785 * VDD) 11011 = Lower guardband rail (0.215 * VDD) 11010 = Internal Band Gap Reference (VBG)(3) 11001-10010 = Unimplemented, do not use 10001 = No channels connected, all inputs floating (used for CTMU) 10000 = No channels connected, all inputs floating (used for CTMU Temperature Sensor input) 01111 = AN15 01110 = AN14 01101 = AN13 01100 = AN12 01011 = AN11 01010 = AN10 01001 = AN9 01000 = AN8(1) 00111 = AN7(1) 00110 = AN6(1) 00101 = AN5(2) 00100 = AN4 00011 = AN3 00010 = AN2 00001 = AN1 00000 = AN0 CH0NA: Sample A Channel 0 Negative Input Select bits Same definitions as for CHONB. CH0SA: Sample A Channel 0 Positive Input Select bits Same definitions as for CHONA. Implemented on 44-pin devices only. Implemented on 28-pin and 44-pin devices only. Actual band gap value used for this input is selected by the PVCFG bits (AD1CON2). bit 12-8 bit 7-5 bit 4-0 Note 1: 2: 3:  2011 Microchip Technology Inc. DS39995B-page 219 PIC24FV32KA304 FAMILY REGISTER 22-6: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-2 bit 1-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0 CHH17 AD1CHITH: A/D SCAN COMPARE HIT REGISTER (HIGH WORD)(1) U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 CHH16 bit 0 Unimplemented: Read as ‘0’. CHH: A/D Compare Hit bits If CM = 11: 1 = A/D Result Buffer x has been written with data or a match has occurred 0 = A/D Result Buffer x has not been written with data For all other values of CM: 1 = A match has occurred on A/D Result Channel x 0 =No match has occurred on A/D Result Channel x Unimplemented channels are read as ‘0’. Note 1: REGISTER 22-7: R/W-0 CHH15 bit 15 R/W-0 CHH7 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-0 AD1CHITL: A/D SCAN COMPARE HIT REGISTER (LOW WORD)(1) R/W-0 CHH13 R/W-0 CHH12 R/W-0 CHH11 R/W-0 CHH10 R/W-0 CHH9 R/W-0 CHH8 bit 8 R/W-0 CHH14 R/W-0 CHH6 R/W-0 CHH5 R/W-0 CHH4 R/W-0 CHH3 R/W-0 CHH2 R/W-0 CHH1 R/W-0 CHH0 bit 0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown CHH: A/D Compare Hit bits If CM = 11: 1 = A/D Result Buffer x has been written with data or a match has occurred 0 = A/D Result Buffer x has not been written with data For all other values of CM: 1 = A match has occurred on A/D Result Channel n 0 = No match has occurred on A/D Result Channel n Unimplemented channels are read as ‘0’. Note 1: DS39995B-page 220  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 22-8: U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 bit 14-10 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0 CSS17 AD1CSSH: A/D INPUT SCAN SELECT REGISTER (HIGH WORD)(1) R/W-0 CSS29 R/W-0 CSS28 R/W-0 CSS27 R/W-0 CSS26 U-0 — U-0 — bit 8 R/W-0 CSS16 bit 0 R/W-0 CSS30 Unimplemented: Read as ‘0’ CSS: A/D Input Scan Selection bits 1 = Include corresponding channel for input scan 0 = Skip channel for input scan Unimplemented: Read as ‘0’ CSS: A/D Input Scan Selection bits 1 = Include corresponding channel for input scan 0 = Skip channel for input scan Unimplemented channels are read as ‘0’. Do not select unimplemented channels for sampling as indeterminate results may be produced. bit 9-2 bit 1-0 Note 1: REGISTER 22-9: R/W-0 CSS15 bit 15 R/W-0 CSS7 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-0 AD1CSSL: A/D INPUT SCAN SELECT REGISTER (LOW WORD)(1) R/W-0 CSS13 R/W-0 CSS12 R/W-0 CSS11 R/W-0 CSS10 R/W-0 CSS9 R/W-0 CSS8 bit 8 R/W-0 CSS14 R/W-0 CSS6 R/W-0 CSS5 R/W-0 CSS4 R/W-0 CSS3 R/W-0 CSS2 R/W-0 CSS1 R/W-0 CSS0 bit 0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown CSS: A/D Input Scan Selection bits 1 = Include corresponding ANx input for scan 0 = Skip channel for input scan Unimplemented channels are read as ‘0’. Do not select unimplemented channels for sampling as indeterminate results may be produced. Note 1:  2011 Microchip Technology Inc. DS39995B-page 221 PIC24FV32KA304 FAMILY REGISTER 22-10: AD1CTMENH: CTMU ENABLE REGISTER (HIGH WORD)(1) U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-2 bit 1-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — R/W-0 CTMEN17 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 CTMEN16 bit 0 Unimplemented: Read as ‘0’. CTMEN: CTMU Enabled During Conversion bits 1 = CTMU is enabled and connected to the selected channel during conversion 0 =CTMU is not connected to this channel Unimplemented channels are read as ‘0’. Note 1: REGISTER 22-11: AD1CTMENL: CTMU ENABLE REGISTER (LOW WORD)(1) R/W-0 CTMEN15 bit 15 R/W-0 CTMEN7 bit 7 Legend: R = Readable bit -n = Value at POR bit 15-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 CTMEN6 R/W-0 CTMEN5 R/W-0 CTMEN4 R/W-0 CTMEN3 R/W-0 CTMEN2 R/W-0 CTMEN1 R/W-0 CTMEN14 R/W-0 CTMEN13 R/W-0 CTMEN12 R/W-0 CTMUEN11 R/W-0 CTMEN10 R/W-0 CTMEN9 R/W-0 CTMEN8 bit 8 R/W-0 CTMEN0 bit 0 CTMEN: CTMU Enabled During Conversion bits 1 = CTMU is enabled and connected to the selected channel during conversion 0 = CTMU is not connected to this channel Unimplemented channels are read as ‘0’. Note 1: DS39995B-page 222  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 22.2 A/D Sampling Requirements The analog input model of the 12-bit A/D Converter is shown in Figure 22-2. The total sampling time for the A/D is a function of the holding capacitor charge time. For the A/D Converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the voltage level on the analog input pin. The source impedance (RS), the interconnect impedance (RIC) and the internal sampling switch (RSS) impedance combine to directly affect the time required to charge CHOLD. The combined impedance of the analog sources must, therefore, be small enough to fully charge the holding capacitor within the chosen sample time. To minimize the effects of pin leakage currents on the accuracy of the A/D Converter, the maximum recommended source impedance, RS, is 2.5 k. After the analog input channel is selected (changed), this sampling function must be completed prior to starting the conversion. The internal holding capacitor will be in a discharged state prior to each sample operation. At least 1 TAD time period should be allowed between conversions for the sample time. For more details, see Section 29.0 “Electrical Characteristics”. EQUATION 22-1: A/D CONVERSION CLOCK PERIOD T AD = T CY  ADCS + 1  ADCS = T AD – 1 --------T CY Note: Based on TCY = 2/FOSC; Doze mode and PLL are disabled. FIGURE 22-2: 12-BIT A/D CONVERTER ANALOG INPUT MODEL RIC  250 Rs VA ANx Sampling Switch RSS RSS  3 k CHOLD = 4.4 pF VSS CPIN ILEAKAGE 500 nA Legend: CPIN = Input Capacitance = Threshold Voltage VT ILEAKAGE = Leakage Current at the pin due to various junctions RIC = Interconnect Resistance RSS = Sampling Switch Resistance CHOLD = Sample-and-Hold Capacitance (from DAC) Note: CPIN value depends on device package and is not tested. Effect of CPIN negligible if Rs  5 k.  2011 Microchip Technology Inc. DS39995B-page 223 PIC24FV32KA304 FAMILY 22.3 Transfer Function The transfer functions of the A/D Converter in 12-bit resolution are shown in Figure 22-3. The difference of the input voltages, (VINH – VINL), is compared to the reference, ((VR+) – (VR-)). • The first code transition occurs when the input voltage is ((VR+) – (VR-))/4096 or 1.0 LSb. • The 0000 0000 0001 code is centered at VR- + (1.5 * ((VR+) – (VR-))/4096). • The 0010 0000 0000 code is centered at VREFL + (2048.5 * ((VR+) – (VR-))/4096). • An input voltage less than VR- + (((VR-) – (VR-))/4096) converts as 0000 0000 0000. • An input voltage greater than (VR-) + (1023 ((VR+) – (VR-))/4096) converts as 1111 1111 1111. FIGURE 22-3: Output Code (Binary (Decimal)) 12-BIT A/D TRANSFER FUNCTION 1111 1111 1111 (4095) 1111 1111 1110 (4094) 0010 0000 0011 (2051) 0010 0000 0010 (2050) 0010 0000 0001 (2049) 0010 0000 0000 (2048) 0001 1111 1111 (2047) 0001 1111 1110 (2046) 0001 1111 1101 (2045) 0000 0000 0001 (1) 0000 0000 0000 (0) 2048 * (VR+ – VR-) 4095 * (VR+ – VR-) (VINH – VINL) 0 VRVR+ – VR4096 VR+ 4096 Voltage Level VR- + VR-+ 4096 DS39995B-page 224  2011 Microchip Technology Inc. VR- + PIC24FV32KA304 FAMILY 23.0 Note: COMPARATOR MODULE This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the Comparator module, refer to the “PIC24F Family Reference Manual”, Section 46. “Scalable Comparator Module” (DS39734). The comparator outputs may be directly connected to the CxOUT pins. When the respective COE equals ‘1’, the I/O pad logic makes the unsynchronized output of the comparator available on the pin. A simplified block diagram of the module is shown in Figure 23-1. Diagrams of the possible individual comparator configurations are shown in Figure 23-2. Each comparator has its own control register, CMxCON (Register 23-1), for enabling and configuring its operation. The output and event status of all three comparators is provided in the CMSTAT register (Register 23-2). The comparator module provides three dual input comparators. The inputs to the comparator can be configured to use any one of four external analog inputs, as well as a voltage reference input from either the internal band gap reference, divided by 2 (VBG/2), or the comparator voltage reference generator. FIGURE 23-1: CCH CREF COMPARATOR MODULE BLOCK DIAGRAM EVPOL Trigger/Interrupt Logic CEVT COE CXINB CXINC CXIND VBG/2 Input Select Logic VINVIN+ C1 CPOL COUT C1OUT Pin CPOL VINVIN+ C2 Trigger/Interrupt Logic CEVT COE COUT C2OUT Pin EVPOL Trigger/Interrupt Logic CEVT COE CXINA CVREF CPOL VINVIN+ C3 COUT C3OUT Pin  2011 Microchip Technology Inc. DS39995B-page 225 PIC24FV32KA304 FAMILY FIGURE 23-2: INDIVIDUAL COMPARATOR CONFIGURATIONS Comparator Off CON = 0, CREF = x, CCH = xx VINVIN+ COE - Cx Off (Read as ‘0’) CxOUT Pin Comparator CxINB > CxINA Compare CON = 1, CREF = 0, CCH = 00 VINVIN+ COE Comparator CxINC > CxINA Compare CON = 1, CREF = 0, CCH = 01 VINVIN+ COE CXINB CXINA - Cx CxOUT Pin CXINC CXINA - Cx CxOUT Pin Comparator CxIND > CxINA Compare CON = 1, CREF = 0, CCH = 10 VINVIN+ Comparator VBG > CxINA Compare CON = 1, CREF = 0, CCH = 11 COE CXIND CXINA Cx VBG/2 CxOUT Pin CXINA VINVIN+ COE Cx CxOUT Pin Comparator CxINB > CVREF Compare CON = 1, CREF = 1, CCH = 00 VINVIN+ COE Comparator CxINC > CVREF Compare CON = 1, CREF = 1, CCH = 01 VINVIN+ COE CXINB CVREF Cx CxOUT Pin CXINC CVREF - Cx CxOUT Pin Comparator CxIND > CVREF Compare CON = 1, CREF = 1, CCH = 10 VINVIN+ Comparator VBG > CVREF Compare CON = 1, CREF = 1, CCH = 11 COE VINVIN+ CXIND CVREF Cx VBG/2 CxOUT Pin CVREF Cx COE CxOUT Pin DS39995B-page 226  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 23-1: R/W-0 CON bit 15 R/W-0 EVPOL1 bit 7 CMxCON: COMPARATOR x CONTROL REGISTERS R/W-0 CPOL R/W-0 CLPWR U-0 — U-0 — R/W-0 CEVT R-0 COUT bit 8 R/W-0 CCH0 bit 0 R/W-0 COE R/W-0 EVPOL0 U-0 — R/W-0 CREF U-0 — U-0 — R/W-0 CCH1 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 14 bit 13 bit 12 bit 11-10 bit 9 bit 8 bit 7-6 bit 5 CON: Comparator Enable bit 1 = Comparator is enabled 0 = Comparator is disabled COE: Comparator Output Enable bit 1 = Comparator output is present on the CxOUT pin 0 = Comparator output is internal only CPOL: Comparator Output Polarity Select bit 1 = Comparator output is inverted 0 = Comparator output is not inverted CLPWR: Comparator Low-Power Mode Select bit 1 = Comparator operates in Low-Power mode 0 = Comparator does not operate in Low-Power mode Unimplemented: Read as ‘0’ CEVT: Comparator Event bit 1 = Comparator event defined by EVPOL has occurred; subsequent triggers and interrupts are disabled until the bit is cleared 0 = Comparator event has not occurred COUT: Comparator Output bit When CPOL = 0: 1 = VIN+ > VIN0 = VIN+ < VINWhen CPOL = 1: 1 = VIN+ < VIN0 = VIN+ > VINEVPOL: Trigger/Event/Interrupt Polarity Select bits 11 = Trigger/event/interrupt generated on any change of the comparator output (while CEVT = 0) 10 = Trigger/event/interrupt generated on transition of the comparator output: If CPOL = 0 (non-inverted polarity): High-to-low transition only. If CPOL = 1 (inverted polarity): Low-to-high transition only. 01 = Trigger/event/interrupt generated on transition of comparator output If CPOL = 0 (non-inverted polarity): Low-to-high transition only. If CPOL = 1 (inverted polarity): High-to-low transition only. 00 = Trigger/event/interrupt generation is disabled Unimplemented: Read as ‘0’  2011 Microchip Technology Inc. DS39995B-page 227 PIC24FV32KA304 FAMILY REGISTER 23-1: bit 4 CMxCON: COMPARATOR x CONTROL REGISTERS (CONTINUED) bit 3-2 bit 1-0 CREF: Comparator Reference Select bits (non-inverting input) 1 = Non-inverting input connects to internal CVREF voltage 0 = Non-inverting input connects to CxINA pin Unimplemented: Read as ‘0’ CCH: Comparator Channel Select bits 11 = Inverting input of comparator connects to VBG/2 10 = Inverting input of comparator connects to CxIND pin 01 = Inverting input of comparator connects to CxINC pin 00 = Inverting input of comparator connects to CxINB pin REGISTER 23-2: R/W-0 CMIDL bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 CMSTAT: COMPARATOR MODULE STATUS REGISTER U-0 — U-0 — U-0 — U-0 — R-0, HSC C3EVT R-0, HSC C2EVT R-0, HSC C1EVT bit 8 U-0 — U-0 — U-0 — U-0 — R-0, HSC C3OUT R-0, HSC C2OUT R-0, HSC C1OUT bit 0 HSC = Hardware Settable/Clearable bit W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown CMIDL: Comparator Stop in Idle Mode bit 1 = Discontinue operation of all comparators when device enters Idle mode 0 = Continue operation of all enabled comparators in Idle mode Unimplemented: Read as ‘0’ C3EVT: Comparator 3 Event Status bit (read-only) Shows the current event status of Comparator 2 (CM3CON). C2EVT: Comparator 2 Event Status bit (read-only) Shows the current event status of Comparator 2 (CM2CON). C1EVT: Comparator 1 Event Status bit (read-only) Shows the current event status of Comparator 1 (CM1CON). Unimplemented: Read as ‘0’ C3OUT: Comparator 3 Output Status bit (read-only) Shows the current output of Comparator 3 (CM3CON). C2OUT: Comparator 2 Output Status bit (read-only) Shows the current output of Comparator 2 (CM2CON). C1OUT: Comparator 1 Output Status bit (read-only) Shows the current output of Comparator 1 (CM1CON). bit 14-11 bit 10 bit 9 bit 8 bit 7-3 bit 2 bit 1 bit 0 DS39995B-page 228  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 24.0 Note: COMPARATOR VOLTAGE REFERENCE This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the Comparator Voltage Reference, refer to the “PIC24F Family Reference Manual”, Section 20. “Comparator Module Voltage Reference Module” (DS39709). 24.1 Configuring the Comparator Voltage Reference The comparator voltage reference module is controlled through the CVRCON register (Register 24-1). The comparator voltage reference provides a range of output voltages, with 32 distinct levels. The comparator voltage reference supply voltage can come from either VDD and VSS, or the external VREF+ and VREF-. The voltage source is selected by the CVRSS bit (CVRCON). The settling time of the comparator voltage reference must be considered when changing the CVREF output. FIGURE 24-1: COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM VREF+ AVDD CVRSS = 1 CVRSS = 0 8R CVR CVREN R R R 32-to-1 MUX R 32 Steps CVREF R R R 8R VREFCVRSS = 1 CVRSS = 0 AVSS  2011 Microchip Technology Inc. DS39995B-page 229 PIC24FV32KA304 FAMILY REGISTER 24-1: U-0 — bit 15 R/W-0 CVREN bit 7 Legend: R = Readable bit -n = Value at POR bit 15-8 bit 7 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 CVROE R/W-0 CVRSS R/W-0 CVR4 R/W-0 CVR3 R/W-0 CVR2 R/W-0 CVR1 CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 8 R/W-0 CVR0 bit 0 Unimplemented: Read as ‘0’ CVREN: Comparator Voltage Reference Enable bit 1 = CVREF circuit powered on 0 = CVREF circuit powered down CVROE: Comparator VREF Output Enable bit 1 = CVREF voltage level is output on CVREF pin 0 = CVREF voltage level is disconnected from CVREF pin CVRSS: Comparator VREF Source Selection bit 1 = Comparator reference source, CVRSRC = VREF+ – VREF0 = Comparator reference source, CVRSRC = AVDD – AVSS CVR: Comparator VREF Value Selection 0 ≤ CVR ≤ 31 bits When CVRSS = 1: CVREF = (VREF-) + (CVR/32) • (VREF+ – VREF-) When CVRSS = 0: CVREF = (AVSS) + (CVR/32) • (AVDD – AVSS) bit 6 bit 5 bit 4-0 DS39995B-page 230  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 25.0 Note: CHARGE TIME MEASUREMENT UNIT (CTMU) This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the Charge Measurement Unit, refer to the “PIC24F Family Reference Manual”, Section 53. “Charge Time Measurement Unit (CTMU) with Threshold Detect” (DS39743). 25.1 Measuring Capacitance The CTMU module measures capacitance by generating an output pulse with a width equal to the time between edge events on two separate input channels. The pulse edge events to both input channels can be selected from four sources: two internal peripheral modules (OC1 and Timer1) and up to 13 external pins (CTED1 through CTED13). This pulse is used with the module’s precision current source to calculate capacitance according to the relationship: The Charge Time Measurement Unit (CTMU) is a flexible analog module that provides charge measurement, accurate differential time measurement between pulse sources and asynchronous pulse generation. Its key features include: • • • • Thirteen external edge input trigger sources Polarity control for each edge source Control of edge sequence Control of response to edge levels or edge transitions • Time measurement resolution of one nanosecond • Accurate current source suitable for capacitive measurement Together with other on-chip analog modules, the CTMU can be used to precisely measure time, measure capacitance, measure relative changes in capacitance, or generate output pulses that are independent of the system clock. The CTMU module is ideal for interfacing with capacitive-based touch sensors. The CTMU is controlled through three registers: CTMUCON1, CTMUCON2 and CTMUICON. CTMUCON1 enables the module and controls the mode of operation of the CTMU, as well as controlling edge sequencing. CTMUCON2 controls edge source selection and edge source polarity selection. The CTMUICON register selects the current range of current source and trims the current. EQUATION 25-1: dV I = C  -----dT For capacitance measurements, the A/D Converter samples an external capacitor (CAPP) on one of its input channels after the CTMU output’s pulse. A precision resistor (RPR) provides current source calibration on a second A/D channel. After the pulse ends, the converter determines the voltage on the capacitor. The actual calculation of capacitance is performed in software by the application. Figure 25-1 illustrates the external connections used for capacitance measurements, and how the CTMU and A/D modules are related in this application. This example also shows the edge events coming from Timer1, but other configurations using external edge sources are possible. A detailed discussion on measuring capacitance and time with the CTMU module is provided in the “PIC24F Family Reference Manual”.  2011 Microchip Technology Inc. DS39995B-page 231 PIC24FV32KA304 FAMILY FIGURE 25-1: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR CAPACITANCE MEASUREMENT PIC24F Device Timer1 CTMU EDG1 EDG2 Output Pulse A/D Converter ANx ANY Current Source CAPP RPR DS39995B-page 232  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 25.2 Measuring Time Time measurements on the pulse width can be similarly performed using the A/D module’s internal capacitor (CAD) and a precision resistor for current calibration. Figure 25-2 displays the external connections used for time measurements, and how the CTMU and A/D modules are related in this application. This example also shows both edge events coming from the external CTED pins, but other configurations using internal edge sources are possible. When the module is configured for pulse generation delay by setting the TGEN bit (CTMUCON), the internal current source is connected to the B input of Comparator 2. A capacitor (CDELAY) is connected to the Comparator 2 pin, C2INB, and the comparator voltage reference, CVREF, is connected to C2INA. CVREF is then configured for a specific trip point. The module begins to charge CDELAY when an edge event is detected. When CDELAY charges above the CVREF trip point, a pulse is output on CTPLS. The length of the pulse delay is determined by the value of CDELAY and the CVREF trip point. Figure 25-3 illustrates the external connections for pulse generation, as well as the relationship of the different analog modules required. While CTED1 is shown as the input pulse source, other options are available. A detailed discussion on pulse generation with the CTMU module is provided in the “PIC24F Family Reference Manual”. 25.3 Pulse Generation and Delay The CTMU module can also generate an output pulse with edges that are not synchronous with the device’s system clock. More specifically, it can generate a pulse with a programmable delay from an edge event input to the module. FIGURE 25-2: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR TIME MEASUREMENT PIC24F Device CTMU CTEDX CTEDX EDG1 EDG2 Output Pulse A/D Converter CAD RPR Current Source ANx FIGURE 25-3: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR PULSE DELAY GENERATION PIC24F Device CTEDX EDG1 CTMU CTPLS Current Source Comparator C2INB C2 CDELAY CVREF  2011 Microchip Technology Inc. DS39995B-page 233 PIC24FV32KA304 FAMILY REGISTER 25-1: R/W-0 CTMUEN bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 0 CTMUCON1: CTMU CONTROL REGISTER 1 U-0 — R/W-0 CTMUSIDL R/W-0 TGEN R/W-0 EDGEN R/W-0 EDGSEQEN R/W-0 IDISSEN R/W-0 CTTRIG bit 8 CTMUEN: CTMU Enable bit 1 = Module is enabled 0 = Module is disabled Unimplemented: Read as ‘0’ CTMUSIDL: Stop in Idle Mode bit 1 = Discontinue module operation when device enters Idle mode 0 = Continue module operation in Idle mode TGEN: Time Generation Enable bit 1 = Enables edge delay generation 0 = Disables edge delay generation EDGEN: Edge Enable bit 1 = Edges are not blocked 0 = Edges are blocked EDGSEQEN: Edge Sequence Enable bit 1 = Edge 1 event must occur before Edge 2 event can occur 0 = No edge sequence is needed IDISSEN: Analog Current Source Control bit 1 = Analog current source output is grounded 0 = Analog current source output is not grounded CTTRIG: Trigger Control bit 1 = Trigger output is enabled 0 = Trigger output is disabled Unimplemented: Read as ‘0’ bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 bit 7-0 DS39995B-page 234  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 25-2: R/W-0 EDG1EDGE bit 15 R/W-0 EDG2EDGE bit 7 Legend: R = Readable bit -n = Value at POR bit 15 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R/W-0 EDG2POL R/W-0 EDG2SEL3 R/W-0 EDG2SEL2 R/W-0 EDG2SEL1 R/W-0 EDG2SEL0 U-0 — U-0 — bit 0 CTMUCON2: CTMU CONTROL REGISTER 2 R/W-0 EDG1SEL3 R/W-0 EDG1SEL2 R/W-0 EDG1SEL1 R/W-0 EDG1SEL0 R/W-0 EDG2 R/W-0 EDG1 bit 8 R/W-0 EDG1POL EDG1EDGE: Edge 1 Edge-Sensitive Select bit 1 = Input is edge-sensitive 0 = Input is level-sensitive EDG1POL: Edge 1 Polarity Select bit 1 = Edge 1 is programmed for a positive edge response 0 = Edge 1 is programmed for a negative edge response EDG1SEL: Edge 1 Source Select bits 1111 = Edge 1 source is Comparator 3 output 1110 = Edge 1 source is Comparator 2 output 1101 = Edge 1 source is Comparator 1 output 1100 = Edge 1 source is IC3 1011 = Edge 1 source is IC2 1010 = Edge 1 source is IC1 1001 = Edge 1 source is CTED8 1000 = Edge 1 source is CTED7 0111 = Edge 1 source is CTED6 0110 = Edge 1 source is CTED5 0101 = Edge 1 source is CTED4 0100 = Edge 1 source is CTED3(2) 0011 = Edge 1 source is CTED1 0010 = Edge 1 source is CTED2 0001 = Edge 1 source is OC1 0000 = Edge 1 source is Timer1 EDG2: Edge 2 Status bit Indicates the status of Edge 2 and can be written to control current source. 1 = Edge 2 has occurred 0 = Edge 2 has not occurred EDG1: Edge 1 Status bit Indicates the status of Edge 1 and can be written to control current source. 1 = Edge 1 has occurred 0 = Edge 1 has not occurred EDG2EDGE: Edge 2 Edge-Sensitive Select bit 1 = Input is edge-sensitive 0 = Input is level-sensitive Edge sources, CTED11 and CTED12, are not available on PIC24FV32KA302 devices. Edge sources, CTED3,CTED11, CTED12 and CTED13, are not available on PIC24FV32KA301 devices. bit 14 bit 13-10 bit 9 bit 8 bit 7 Note 1: 2:  2011 Microchip Technology Inc. DS39995B-page 235 PIC24FV32KA304 FAMILY REGISTER 25-2: bit 6 CTMUCON2: CTMU CONTROL REGISTER 2 (CONTINUED) EDG2POL: Edge 2 Polarity Select bit 1 = Edge 2 is programmed for a positive edge 0 = Edge 2 is programmed for a negative edge EDG2SEL: Edge 2 Source Select bits 1111 = Edge 2 source is Comparator 3 output 1110 = Edge 2 source is Comparator 2 output 1101 = Edge 2 source is Comparator 1 output 1100 = Unimplemented; do not use 1011 = Edge 2 source is IC3 1010 = Edge 2 source is IC2 1001 = Edge 2 source is IC1 1000 = Edge 2 source is CTED13(2) 0111 = Edge 2 source is CTED12(1,2) 0110 = Edge 2 source is CTED11(1,2) 0101 = Edge 2 source is CTED10 0100 = Edge 2 source is CTED9 0011 = Edge 2 source is CTED1 0010 = Edge 2 source is CTED2 0001 = Edge 2 source is OC1 0000 = Edge 2 source is Timer1 Unimplemented: Read as ‘0’ Edge sources, CTED11 and CTED12, are not available on PIC24FV32KA302 devices. Edge sources, CTED3,CTED11, CTED12 and CTED13, are not available on PIC24FV32KA301 devices. bit 5-2 bit 1-0 Note 1: 2: DS39995B-page 236  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 25-3: R/W-0 ITRIM5 bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 15-10 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 0 CTMUICON: CTMU CURRENT CONTROL REGISTER R/W-0 ITRIM3 R/W-0 ITRIM2 R/W-0 ITRIM1 R/W-0 ITRIM0 R/W-0 IRNG1 R/W-0 IRNG0 bit 8 R/W-0 ITRIM4 ITRIM: Current Source Trim bits 011111 = Maximum positive change from nominal current 011110 . . . 000001 = Minimum positive change from nominal current 000000 = Nominal current output specified by IRNG 111111 = Minimum negative change from nominal current . . . 100010 100001 = Maximum negative change from nominal current IRNG: Current Source Range Select bits 11 = 100 x Base Current 10 = 10 × Base Current 01 = Base Current Level (0.55 µA nominal) 00 = 1000 x Base Current Unimplemented: Read as ‘0’ bit 9-8 bit 7-0  2011 Microchip Technology Inc. DS39995B-page 237 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 238  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 26.0 Note: SPECIAL FEATURES This data sheet summarizes the features of this group of PIC24F devices. It is not intended to be a comprehensive reference source. For more information on the Watchdog Timer, High-Level Device Integration and Programming Diagnostics, refer to the individual sections of the “PIC24F Family Reference Manual” provided below: • Section 9. “Watchdog Timer (WDT)” (DS39697) • Section 36. “High-Level Integration with Programmable High/LowVoltage Detect (HLVD)” (DS39725) • Section 33. “Programming and Diagnostics” (DS39716) 26.1 Configuration Bits The Configuration bits can be programmed (read as ‘0’), or left unprogrammed (read as ‘1’), to select various device configurations. These bits are mapped starting at program memory location, F80000h. A complete list is provided in Table 26-1. A detailed explanation of the various bit functions is provided in Register 26-1 through Register 26-8. The address, F80000h, is beyond the user program memory space. In fact, it belongs to the configuration memory space (800000h-FFFFFFh), which can only be accessed using table reads and table writes. TABLE 26-1: Configuration Register FBS FGS FOSCSEL FOSC FWDT FPOR FICD FDS CONFIGURATION REGISTERS LOCATIONS Address F80000 F80004 F80006 F80008 F8000A F8000C F8000E F80010 PIC24FV32KA304 family devices include several features intended to maximize application flexibility and reliability, and minimize cost through elimination of external components. These are: • • • • • Flexible Configuration Watchdog Timer (WDT) Code Protection In-Circuit Serial Programming™ (ICSP™) In-Circuit Emulation REGISTER 26-1: U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 7-4 bit 3-1 FBS: BOOT SEGMENT CONFIGURATION REGISTER U-0 — U-0 — U-0 — R/W-1 BSS2 R/W-1 BSS1 R/W-1 BSS0 R/W-1 BWRP bit 0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown Unimplemented: Read as ‘0’ BSS: Boot Segment Program Flash Code Protection bits 111 = No boot program Flash segment 011 = Reserved 110 = Standard security, boot program Flash segment starts at 200h, ends at 000AFEh 010 = High-security boot program Flash segment starts at 200h, ends at 000AFEh 101 = Standard security, boot program Flash segment starts at 200h, ends at 0015FEh(1) 001 = High-security, boot program Flash segment starts at 200h, ends at 0015FEh(1) 100 = Standard security; boot program Flash segment starts at 200h, ends at 002BFEh(1) 000 = High-security; boot program Flash segment starts at 200h, ends at 002BFEh(1) BWRP: Boot Segment Program Flash Write Protection bit 1 = Boot segment may be written 0 = Boot segment is write-protected This selection should not be used in PIC24FV16KA3XX devices. bit 0 Note 1:  2011 Microchip Technology Inc. DS39995B-page 239 PIC24FV32KA304 FAMILY REGISTER 26-2: U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 7-2 bit 1 C = Clearable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown FGS: GENERAL SEGMENT CONFIGURATION REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — R/C-1 GSS0 R/C-1 GWRP bit 0 Unimplemented: Read as ‘0’ GSS0: General Segment Code Flash Code Protection bit 1 = No protection 0 = Standard security is enabled GWRP: General Segment Code Flash Write Protection bit 1 = General segment may be written 0 = General segment is write-protected bit 0 REGISTER 26-3: R/P-1 IESO bit 7 Legend: R = Readable bit -n = Value at POR bit 7 FOSCSEL: OSCILLATOR SELECTION CONFIGURATION REGISTER R/P-1 SOSCSRC U-0 — U-0 — R/P-1 FNOSC2 R/P-1 FNOSC1 R/P-1 FNOSC0 bit 0 R/P-1 LPRCSEL P = Programmable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown IESO: Internal External Switchover bit 1 = Internal External Switchover mode is enabled (Two-Speed Start-up is enabled) 0 = Internal External Switchover mode is disabled (Two-Speed Start-up is disabled) LPRCSEL: Internal LPRC Oscillator Power Select bit 1 = High-Power/High-Accuracy mode 0 = Low-Power/Low-Accuracy mode SOSCSRC: Secondary Oscillator Clock Source Configuration bit 1 = SOSC analog crystal function is available on the SOSCI/SOSCO pins 0 = SOSC crystal is disabled; digital SCLKI function is selected on SOSCO pin Unimplemented: Read as ‘0’ FNOSC: Oscillator Selection bits 000 = Fast RC Oscillator (FRC) 001 = Fast RC Oscillator with divide-by-N with PLL module (FRCDIV+PLL) 010 = Primary Oscillator (XT, HS, EC) 011 = Primary Oscillator with PLL module (HS+PLL, EC+PLL) 100 = Secondary Oscillator (SOSC) 101 = Low-Power RC Oscillator (LPRC) 110 = 500 kHz Low-Power FRC Oscillator with divide-by-N (LPFRCDIV) 111 = 8 MHz FRC Oscillator with divide-by-N (FRCDIV) bit 6 bit 5 bit 4-3 bit 2-0 DS39995B-page 240  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 26-4: R/P-1 FCKSM1 bit 7 Legend: R = Readable bit -n = Value at POR bit 7-6 P = Programmable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown FOSC: OSCILLATOR CONFIGURATION REGISTER R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 POSCMD1 R/P-1 POSCMD0 bit 0 SOSCSEL POSCFREQ1 POSCFREQ0 OSCIOFNC R/P-1 FCKSM0 FCKSM: Clock Switching and Monitor Selection Configuration bits 1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled 01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled 00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled SOSCSEL: Secondary Oscillator Power Selection Configuration bit 1 = Secondary oscillator is configured for high-power operation 0 = Secondary oscillator is configured for low-power operation POSCFREQ: Primary Oscillator Frequency Range Configuration bits 11 = Primary oscillator/external clock input frequency is greater than 8 MHz 10 = Primary oscillator/external clock input frequency is between 100 kHz and 8 MHz 01 = Primary oscillator/external clock input frequency is less than 100 kHz 00 = Reserved; do not use OSCIOFNC: CLKO Enable Configuration bit 1 = CLKO output signal active on the OSCO pin; primary oscillator must be disabled or configured for the External Clock mode (EC) for the CLKO to be active (POSCMD = 11 or 00) 0 = CLKO output disabled POSCMD: Primary Oscillator Configuration bits 11 = Primary Oscillator mode is disabled 10 = HS Oscillator mode is selected 01 = XT Oscillator mode is selected 00 = External Clock mode is selected bit 5 bit 4-3 bit 2 bit 1-0  2011 Microchip Technology Inc. DS39995B-page 241 PIC24FV32KA304 FAMILY REGISTER 26-5: R/P-1 FWDTEN1 bit 7 Legend: R = Readable bit -n = Value at POR bit 7,5 P = Programmable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown FWDT: WATCHDOG TIMER CONFIGURATION REGISTER R/P-1 FWDTEN0 R/P-1 FWPSA R/P-1 WDTPS3 R/P-1 WDTPS2 R/P-1 WDTPS1 R/P-1 WDTPS0 bit 0 R/P-1 WINDIS FWDTEN: Watchdog Timer Enable bit 11 = WDT is enabled in hardware 10 = WDT is controlled with the SWDTEN bit setting 01 = WDT is enabled only while device is active; WDT is disabled in Sleep; SWDTEN bit is disabled 00 = WDT is disabled in hardware; SWDTEN bit is disabled WINDIS: Windowed Watchdog Timer Disable bit 1 = Standard WDT is selected; windowed WDT is disabled 0 = Windowed WDT is enabled; note that executing a CLRWDT instruction while the WDT is disabled in hardware and software (FWDTEN = 00 and RCON bit, SWDTEN = 0) will not cause a device Reset FWPSA: WDT Prescaler bit 1 = WDT prescaler ratio of 1:128 0 = WDT prescaler ratio of 1:32 WDTPS: Watchdog Timer Postscale Select bits 1111 = 1:32,768 1110 = 1:16,384 1101 = 1:8,192 1100 = 1:4,096 1011 = 1:2,048 1010 = 1:1,024 1001 = 1:512 1000 = 1:256 0111 = 1:128 0110 = 1:64 0101 = 1:32 0100 = 1:16 0011 = 1:8 0010 = 1:4 0001 = 1:2 0000 = 1:1 bit 6 bit 4 bit 3-0 DS39995B-page 242  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 26-6: R/P-1 MCLRE(2) bit 7 Legend: R = Readable bit -n = Value at POR bit 7 P = Programmable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown FPOR: RESET CONFIGURATION REGISTER R/P-1 BORV0(3) R/P-1 I2C1SEL(1) R/P-1 PWRTEN R/P-1 LVRCFG(1) R/P-1 BOREN1 R/P-1 BOREN0 bit 0 R/P-1 BORV1(3) MCLRE: MCLR Pin Enable bit(2) 1 = MCLR pin is enabled; RA5 input pin is disabled 0 = RA5 input pin is enabled; MCLR is disabled BORV: Brown-out Reset Enable bits(3) 11 = Brown-out Reset set to lowest voltage 10 = Brown-out Reset 01 = Brown-out Reset set to highest voltage 00 = Downside protection on POR is enabled – “zero-power” is selected I2C1SEL: Alternate I2C1 Pin Mapping bit(1) 1 = Default location for SCL1/SDA1 pins 0 = Alternate location for SCL1/SDA1 pins PWRTEN: Power-up Timer Enable bit 1 = PWRT is enabled 0 = PWRT is disabled LVRCFG: Low-Voltage Regulator Configuration bit(1) 1 = Low-voltage regulator is not available 0 = Low-voltage regulator is available and controlled by the LVREN bit (RCON) during Sleep BOREN: Brown-out Reset Enable bits 11 = Brown-out Reset is enabled in hardware; SBOREN bit is disabled 10 = Brown-out Reset is enabled only while device is active and disabled in Sleep; SBOREN bit is disabled 01 = Brown-out Reset is controlled with the SBOREN bit setting 00 = Brown-out Reset is disabled in hardware; SBOREN bit is disabled This setting only applies to the “FV” devices. This bit is reserved and should be maintained as ‘1’ on “F” devices. The MCLRE fuse can only be changed when using the VPP-Based ICSP™ mode entry. This prevents a user from accidentally locking out the device from the low-voltage test entry. Refer to Section 29.0 “Electrical Characteristics” for BOR voltages. bit 6-5 bit 4 bit 3 bit 2 bit 1-0 Note 1: 2: 3:  2011 Microchip Technology Inc. DS39995B-page 243 PIC24FV32KA304 FAMILY REGISTER 26-7: R/P-1 DEBUG bit 7 Legend: R = Readable bit -n = Value at POR bit 7 — FICD: IN-CIRCUIT DEBUGGER CONFIGURATION REGISTER U-0 U-0 — U-0 — U-0 — U-0 — R/P-1 FICD1 R/P-1 FICD0 bit 0 P = Programmable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown bit 6-2 bit 1-0 DEBUG: Background Debugger Enable bit 1 = Background debugger is disabled 0 = Background debugger functions are enabled Unimplemented: Read as ‘0’ FICD ICD Pin Select bits 11 = PGEC1/PGED1 are used for programming and debugging the device 10 = PGEC2/PGED2 are used for programming and debugging the device 01 = PGEC3/PGED3 are used for programming and debugging the device 00 = Reserved; do not use DS39995B-page 244  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 26-8: R/P-1 DSWDTEN bit 7 Legend: R = Readable bit -n = Value at POR bit 7 P = Programmable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown FDS: DEEP SLEEP CONFIGURATION REGISTER U-0 — R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 bit 0 DSWDTOSC DSWDTPS3 DSWDTPS2 DSWDTPS1 DSWDTPS0 R/P-1 DSBOREN DSWDTEN: Deep Sleep Watchdog Timer Enable bit 1 = DSWDT is enabled 0 = DSWDT is disabled DSBOREN: Deep Sleep/Low-Power BOR Enable bit (does not affect operation in non Deep Sleep modes) 1 = Deep Sleep BOR is enabled in Deep Sleep 0 = Deep Sleep BOR is disabled in Deep Sleep Unimplemented: Read as ‘0’ DSWDTOSC: DSWDT Reference Clock Select bit 1 = DSWDT uses LPRC as reference clock 0 = DSWDT uses SOSC as reference clock DSWDTPS: Deep Sleep Watchdog Timer Postscale Select bits The DSWDT prescaler is 32; this creates an approximate base time unit of 1 ms. 1111 = 1:2,147,483,648 (25.7 days) nominal 1110 = 1:536,870,912 (6.4 days) nominal 1101 = 1:134,217,728 (38.5 hours) nominal 1100 = 1:33,554,432 (9.6 hours) nominal 1011 = 1:8,388,608 (2.4 hours) nominal 1010 = 1:2,097,152 (36 minutes) nominal 1001 = 1:524,288 (9 minutes) nominal 1000 = 1:131,072 (135 seconds) nominal 0111 = 1:32,768 (34 seconds) nominal 0110 = 1:8,192 (8.5 seconds) nominal 0101 = 1:2,048 (2.1 seconds) nominal 0100 = 1:512 (528 ms) nominal 0011 = 1:128 (132 ms) nominal 0010 = 1:32 (33 ms) nominal 0001 = 1:8 (8.3 ms) nominal 0000 = 1:2 (2.1 ms) nominal bit 6 bit 5 bit 4 bit 3-0  2011 Microchip Technology Inc. DS39995B-page 245 PIC24FV32KA304 FAMILY REGISTER 26-9: U-0 — bit 23 R FAMID7 bit 15 R DEV7 bit 7 Legend: R = Readable bit -n = Value at POR bit 23-16 bit 15-8 bit 7-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown R DEV6 R DEV5 R DEV4 R DEV3 R DEV2 R DEV1 R DEV0 bit 0 R FAMID6 R FAMID5 R FAMID4 R FAMID3 R FAMID2 R FAMID1 R FAMID0 bit 8 DEVID: DEVICE ID REGISTER U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 16 Unimplemented: Read as ‘0’ FAMID: Device Family Identifier bits 01000101 = PIC24FV32KA304 family DEV: Individual Device Identifier bits 00010111 = PIC24FV32KA304 00000111 = PIC24FV16KA304 00010011 = PIC24FV32KA302 00000011 = PIC24FV16KA302 00011001 = PIC24FV32KA301 00001001 = PIC24FV16KA301 00010110 = PIC24F32KA304 00000110 = PIC24F16KA304 00010010 = PIC24F32KA302 00000010 = PIC24F16KA302 00011000 = PIC24F32KA301 00001000 = PIC24F16KA301 DS39995B-page 246  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY REGISTER 26-10: DEVREV: DEVICE REVISION REGISTER U-0 — bit 23 U-0 — bit 15 U-0 — bit 7 Legend: R = Readable bit -n = Value at POR bit 23-4 bit 3-0 W = Writable bit ‘1’ = Bit is set U = Unimplemented bit, read as ‘0’ ‘0’ = Bit is cleared x = Bit is unknown U-0 — U-0 — U-0 — R REV3 R REV2 R REV1 R REV0 bit 0 U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — U-0 — bit 16 U-0 — bit 8 Unimplemented: Read as ‘0’ REV: Minor Revision Identifier bits  2011 Microchip Technology Inc. DS39995B-page 247 PIC24FV32KA304 FAMILY 26.2 On-Chip Voltage Regulator FIGURE 26-1: All of the PIC24FV32KA304 family of devices power their core digital logic at a nominal 3.0V. This may create an issue for designs that are required to operate at a higher typical voltage, as high as 5.0V. To simplify system design, all devices in the ‘‘FV’’ family incorporate an on-chip regulator that allows the device to run its core logic from VDD. The regulator is always enabled and provides power to the core from the other VDD pins. A low-ESR capacitor (such as ceramic) must be connected to the VCAP pin (Figure 26-1). This helps to maintain the stability of the regulator. The recommended value for the filter capacitor is provided in Section 29.1 “DC Characteristics”. In all of the PIC24FJ64GA family of devices, the regulator is disabled. For the ‘‘F’’ devices, the VDDCORE and VDD pins are internally tied together to operate at an overall lower allowable voltage range (1.8-3.6V). Refer to Figure 26-1 for possible configurations. CONNECTIONS FOR THE ON-CHIP REGULATOR 5.0V PIC24FV32KA304 VDD Regulator Enabled: VCAP CEFC (10 F typ) VSS Note 1: These are typical operating voltages. Refer to Section 29.0 “Electrical Characteristics” for the full operating ranges of VDD and VDDCORE. 26.2.2 ON-CHIP REGULATOR AND POR 26.2.1 VOLTAGE REGULATOR TRACKING MODE AND LOW-VOLTAGE DETECTION For PIC24FV32KA304 devices, it takes approximately 1 s for it to generate output. During this time, designated as TPM, code execution is disabled. TPM is applied every time the device resumes operation after any power-down, including Sleep mode. For all PIC24FV32KA304 devices, the on-chip regulator provides a constant voltage of 3.0V nominal to the digital core logic. The regulator can provide this level from a VDD of about 3.0V, all the way up to the device’s VDDMAX. It does not have the capability to boost VDD levels below 3.0V. In order to prevent “brown out” conditions when the voltage drops too low for the regulator, the regulator enters Tracking mode. In Tracking mode, the regulator output follows VDD with a typical voltage drop of 100 mV. When the device enters Tracking mode, it is no longer possible to operate at full speed. To provide information about when the device enters Tracking mode, the on-chip regulator includes a simple, High/Low-Voltage Detect (HLVD) circuit. When VDD drops below full-speed operating voltage, the circuit sets the High/Low-Voltage Detect Interrupt Flag, HLVDIF (IFS4). This can be used to generate an interrupt and put the application into a low-power operational mode or trigger an orderly shutdown. High/Low-Voltage Detection is only available for ‘‘FV’’ parts. 26.3 Watchdog Timer (WDT) For the PIC24FV32KA304 family of devices, the WDT is driven by the LPRC oscillator. When the WDT is enabled, the clock source is also enabled. The nominal WDT clock source from LPRC is 31 kHz. This feeds a prescaler that can be configured for either 5-bit (divide-by-32) or 7-bit (divide-by-128) operation. The prescaler is set by the FWPSA Configuration bit. With a 31 kHz input, the prescaler yields a nominal WDT time-out period (TWDT) of 1 ms in 5-bit mode or 4 ms in 7-bit mode. A variable postscaler divides down the WDT prescaler output and allows for a wide range of time-out periods. The postscaler is controlled by the Configuration bits, WDTPS (FWDT), which allow the selection of a total of 16 settings, from 1:1 to 1:32,768. Using the prescaler and postscaler time-out periods, ranging from 1 ms to 131 seconds, can be achieved. DS39995B-page 248  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY The WDT, prescaler and postscaler are reset: • On any device Reset • On the completion of a clock switch, whether invoked by software (i.e., setting the OSWEN bit after changing the NOSC bits) or by hardware (i.e., Fail-Safe Clock Monitor) • When a PWRSAV instruction is executed (i.e., Sleep or Idle mode is entered) • When the device exits Sleep or Idle mode to resume normal operation • By a CLRWDT instruction during normal execution If the WDT is enabled in hardware (FWDTEN = 11), it will continue to run during Sleep or Idle modes. When the WDT time-out occurs, the device will wake and code execution will continue from where the PWRSAV instruction was executed. The corresponding SLEEP or IDLE bits (RCON) will need to be cleared in software after the device wakes up. The WDT Flag bit, WDTO (RCON), is not automatically cleared following a WDT time-out. To detect subsequent WDT events, the flag must be cleared in software. Note: The CLRWDT and PWRSAV instructions clear the prescaler and postscaler counts when executed. 26.3.1 WINDOWED OPERATION The Watchdog Timer has an optional Fixed Window mode of operation. In this Windowed mode, CLRWDT instructions can only reset the WDT during the last 1/4 of the programmed WDT period. A CLRWDT instruction executed before that window causes a WDT Reset, similar to a WDT time-out. Windowed WDT mode is enabled by programming the Configuration bit, WINDIS (FWDT), to ‘0’. 26.3.2 CONTROL REGISTER The WDT is enabled or disabled by the FWDTEN Configuration bits. When both the FWDTEN Configuration bits are set, the WDT is always enabled. The WDT can be optionally controlled in software when the FWDTEN Configuration bits have been programmed to ‘10’. The WDT is enabled in software by setting the SWDTEN control bit (RCON). The SWDTEN control bit is cleared on any device Reset. The software WDT option allows the user to enable the WDT for critical code segments, and disable the WDT during non-critical segments, for maximum power savings. When the FWTEN bits are set to ‘01’, the WDT is enabled only in Run and Idle modes, and is disabled in Sleep. Software control of the WDT SWDTEN bit (RCON) is disabled with this setting. FIGURE 26-2: SWDTEN FWDTEN WDT BLOCK DIAGRAM LPRC Control FWPSA Prescaler (5-Bit/7-Bit) 31 kHz 1 ms/4 ms WDT Counter WDTPS Postscaler 1:1 to 1:32.768 WDT Overflow Reset Wake from Sleep LPRC Input All Device Resets Transition to New Clock Source Exit Sleep or Idle Mode CLRWDT Instr. PWRSAV Instr. Sleep or Idle Mode  2011 Microchip Technology Inc. DS39995B-page 249 PIC24FV32KA304 FAMILY 26.4 Deep Sleep Watchdog Timer (DSWDT) 26.6 In-Circuit Serial Programming PIC24FV32KA304 family microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock (PGECx) and data (PGEDx) and three other lines for power, ground and the programming voltage. This allows customers to manufacture boards with unprogrammed devices and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. In PIC24FV32KA304 family devices, in addition to the WDT module, a DSWDT module is present which runs while the device is in Deep Sleep, if enabled. It is driven by either the SOSC or LPRC oscillator. The clock source is selected by the Configuration bit, DSWCKSEL (FDS). The DSWDT can be configured to generate a time-out at 2.1 ms to 25.7 days by selecting the respective postscaler. The postscaler can be selected by the Configuration bits, DSWDTPS (FDS). When the DSWDT is enabled, the clock source is also enabled. DSWDT is one of the sources that can wake-up the device from Deep Sleep mode. 26.7 In-Circuit Debugger 26.5 Program Verification and Code Protection When MPLAB® ICD 3, MPLAB REAL ICE™ or PICkit™ 3 is selected as a debugger, the in-circuit debugging functionality is enabled. This function allows simple debugging functions when used with MPLAB IDE. Debugging functionality is controlled through the PGECx and PGEDx pins. To use the in-circuit debugger function of the device, the design must implement ICSP connections to MCLR, VDD, VSS, PGECx, PGEDx and the pin pair. In addition, when the feature is enabled, some of the resources are not available for general use. These resources include the first 80 bytes of data RAM and two I/O pins. For all devices in the PIC24FV32KA304 family, code protection for the boot segment is controlled by the Configuration bit, BSS0, and the general segment by the Configuration bit, GSS0. These bits inhibit external reads and writes to the program memory space This has no direct effect in normal execution mode. Write protection is controlled by bit, BWRP, for the boot segment and bit, GWRP, for the general segment in the Configuration Word. When these bits are programmed to ‘0’, internal write and erase operations to program memory are blocked. DS39995B-page 250  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 27.0 DEVELOPMENT SUPPORT 27.1 The PIC® microcontrollers and dsPIC® digital signal controllers are supported with a full range of software and hardware development tools: • Integrated Development Environment - MPLAB® IDE Software • Compilers/Assemblers/Linkers - MPLAB C Compiler for Various Device Families - HI-TECH C for Various Device Families - MPASMTM Assembler - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB Assembler/Linker/Librarian for Various Device Families • Simulators - MPLAB SIM Software Simulator • Emulators - MPLAB REAL ICE™ In-Circuit Emulator • In-Circuit Debuggers - MPLAB ICD 3 - PICkit™ 3 Debug Express • Device Programmers - PICkit™ 2 Programmer - MPLAB PM3 Device Programmer • Low-Cost Demonstration/Development Boards, Evaluation Kits, and Starter Kits MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16/32-bit microcontroller market. The MPLAB IDE is a Windows® operating system-based application that contains: • A single graphical interface to all debugging tools - Simulator - Programmer (sold separately) - In-Circuit Emulator (sold separately) - In-Circuit Debugger (sold separately) • A full-featured editor with color-coded context • A multiple project manager • Customizable data windows with direct edit of contents • High-level source code debugging • Mouse over variable inspection • Drag and drop variables from source to watch windows • Extensive on-line help • Integration of select third party tools, such as IAR C Compilers The MPLAB IDE allows you to: • Edit your source files (either C or assembly) • One-touch compile or assemble, and download to emulator and simulator tools (automatically updates all project information) • Debug using: - Source files (C or assembly) - Mixed C and assembly - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power.  2011 Microchip Technology Inc. DS39995B-page 251 PIC24FV32KA304 FAMILY 27.2 MPLAB C Compilers for Various Device Families 27.5 MPLINK Object Linker/ MPLIB Object Librarian The MPLAB C Compiler code development systems are complete ANSI C compilers for Microchip’s PIC18, PIC24 and PIC32 families of microcontrollers and the dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler and the MPLAB C18 C Compiler. It can link relocatable objects from precompiled libraries, using directives from a linker script. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: • Efficient linking of single libraries instead of many smaller files • Enhanced code maintainability by grouping related modules together • Flexible creation of libraries with easy module listing, replacement, deletion and extraction 27.3 HI-TECH C for Various Device Families The HI-TECH C Compiler code development systems are complete ANSI C compilers for Microchip’s PIC family of microcontrollers and the dsPIC family of digital signal controllers. These compilers provide powerful integration capabilities, omniscient code generation and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple platforms. 27.6 MPLAB Assembler, Linker and Librarian for Various Device Families 27.4 MPASM Assembler The MPASM Assembler is a full-featured, universal macro assembler for PIC10/12/16/18 MCUs. The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel® standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM Assembler features include: • Integration into MPLAB IDE projects • User-defined macros to streamline assembly code • Conditional assembly for multi-purpose source files • Directives that allow complete control over the assembly process MPLAB Assembler produces relocatable machine code from symbolic assembly language for PIC24, PIC32 and dsPIC devices. MPLAB C Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: • • • • • • Support for the entire device instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility DS39995B-page 252  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 27.7 MPLAB SIM Software Simulator 27.9 The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC® DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB SIM Software Simulator fully supports symbolic debugging using the MPLAB C Compilers, and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool. MPLAB ICD 3 In-Circuit Debugger System MPLAB ICD 3 In-Circuit Debugger System is Microchip’s most cost effective high-speed hardware debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU) devices. It debugs and programs PIC® Flash microcontrollers and dsPIC® DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated Development Environment (IDE). The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer’s PC using a high-speed USB 2.0 interface and is connected to the target with a connector compatible with the MPLAB ICD 2 or MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3 supports all MPLAB ICD 2 headers. 27.8 MPLAB REAL ICE In-Circuit Emulator System 27.10 PICkit 3 In-Circuit Debugger/ Programmer and PICkit 3 Debug Express The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer’s PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming™. The PICkit 3 Debug Express include the PICkit 3, demo board and microcontroller, hookup cables and CDROM with user’s guide, lessons, tutorial, compiler and MPLAB IDE software. MPLAB REAL ICE In-Circuit Emulator System is Microchip’s next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs PIC® Flash MCUs and dsPIC® Flash DSCs with the easy-to-use, powerful graphical user interface of the MPLAB Integrated Development Environment (IDE), included with each kit. The emulator is connected to the design engineer’s PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal (LVDS) interconnection (CAT5). The emulator is field upgradable through future firmware downloads in MPLAB IDE. In upcoming releases of MPLAB IDE, new devices will be supported, and new features will be added. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, run-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables.  2011 Microchip Technology Inc. DS39995B-page 253 PIC24FV32KA304 FAMILY 27.11 PICkit 2 Development Programmer/Debugger and PICkit 2 Debug Express The PICkit™ 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash families of microcontrollers. The full featured Windows® programming interface supports baseline (PIC10F, PIC12F5xx, PIC16F5xx), midrange (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. With Microchip’s powerful MPLAB Integrated Development Environment (IDE) the PICkit™ 2 enables in-circuit debugging on most PIC® microcontrollers. In-Circuit-Debugging runs, halts and single steps the program while the PIC microcontroller is embedded in the application. When halted at a breakpoint, the file registers can be examined and modified. The PICkit 2 Debug Express include the PICkit 2, demo board and microcontroller, hookup cables and CDROM with user’s guide, lessons, tutorial, compiler and MPLAB IDE software. 27.13 Demonstration/Development Boards, Evaluation Kits, and Starter Kits A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for adding custom circuitry and provide application firmware and source code for examination and modification. The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstration software for analog filter design, KEELOQ® security ICs, CAN, IrDA®, PowerSmart battery management, SEEVAL® evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Also available are starter kits that contain everything needed to experience the specified device. This usually includes a single application and debug capability, all on one board. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. 27.12 MPLAB PM3 Device Programmer The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages and a modular, detachable socket assembly to support various package types. The ICSP™ cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an MMC card for file storage and data applications. DS39995B-page 254  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 28.0 Note: INSTRUCTION SET SUMMARY This chapter is a brief summary of the PIC24F instruction set architecture and is not intended to be a comprehensive reference source. The literal instructions that involve data movement may use some of the following operands: • A literal value to be loaded into a W register or file register (specified by the value of ‘k’) • The W register or file register where the literal value is to be loaded (specified by ‘Wb’ or ‘f’) However, literal instructions that involve arithmetic or logical operations use some of the following operands: • The first source operand, which is a register ‘Wb’ without any address modifier • The second source operand, which is a literal value • The destination of the result (only if not the same as the first source operand), which is typically a register ‘Wd’ with or without an address modifier The control instructions may use some of the following operands: • A program memory address • The mode of the table read and table write instructions All instructions are a single word, except for certain double-word instructions, which were made double-word instructions so that all of the required information is available in these 48 bits. In the second word, the 8 MSbs are ‘0’s. If this second word is executed as an instruction (by itself), it will execute as a NOP. Most single-word instructions are executed in a single instruction cycle, unless a conditional test is true or the Program Counter (PC) is changed as a result of the instruction. In these cases, the execution takes two instruction cycles, with the additional instruction cycle(s) executed as a NOP. Notable exceptions are the BRA (unconditional/computed branch), indirect CALL/GOTO, all table reads and writes, and RETURN/RETFIE instructions, which are single-word instructions but take two or three cycles. Certain instructions that involve skipping over the subsequent instruction require either two or three cycles if the skip is performed, depending on whether the instruction being skipped is a single-word or two-word instruction. Moreover, double-word moves require two cycles. The double-word instructions execute in two instruction cycles. The PIC24F instruction set adds many enhancements to the previous PIC® MCU instruction sets, while maintaining an easy migration from previous PIC MCU instruction sets. Most instructions are a single program memory word. Only three instructions require two program memory locations. Each single-word instruction is a 24-bit word divided into an 8-bit opcode, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. The instruction set is highly orthogonal and is grouped into four basic categories: • • • • Word or byte-oriented operations Bit-oriented operations Literal operations Control operations Table 28-1 lists the general symbols used in describing the instructions. The PIC24F instruction set summary in Table 28-2 lists all the instructions, along with the status flags affected by each instruction. Most word or byte-oriented W register instructions (including barrel shift instructions) have three operands: • The first source operand, which is typically a register ‘Wb’ without any address modifier • The second source operand, which is typically a register ‘Ws’ with or without an address modifier • The destination of the result, which is typically a register ‘Wd’ with or without an address modifier However, word or byte-oriented file register instructions have two operands: • The file register specified by the value, ‘f’ • The destination, which could either be the file register, ‘f’, or the W0 register, which is denoted as ‘WREG’ Most bit-oriented instructions (including rotate/shift instructions) have two operands: simple • The W register (with or without an address modifier) or file register (specified by the value of ‘Ws’ or ‘f’) • The bit in the W register or file register (specified by a literal value or indirectly by the contents of register ‘Wb’)  2011 Microchip Technology Inc. DS39995B-page 255 PIC24FV32KA304 FAMILY TABLE 28-1: Field #text (text) [text] {} .b .d .S .w bit4 C, DC, N, OV, Z Expr f lit1 lit4 lit5 lit8 lit10 lit14 lit16 lit23 None PC Slit10 Slit16 Slit6 Wb Wd Wdo Wm,Wn Wn Wnd Wns WREG Ws Wso Means literal defined by “text” Means “content of text” Means “the location addressed by text” Optional field or operation Register bit field Byte mode selection Double-Word mode selection Shadow register select Word mode selection (default) 4-bit bit selection field (used in word addressed instructions) {0...15} MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero Absolute address, label or expression (resolved by the linker) File register address {0000h...1FFFh} 1-bit unsigned literal {0,1} 4-bit unsigned literal {0...15} 5-bit unsigned literal {0...31} 8-bit unsigned literal {0...255} 10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode 14-bit unsigned literal {0...16384} 16-bit unsigned literal {0...65535} 23-bit unsigned literal {0...8388608}; LSB must be ‘0’ Field does not require an entry, may be blank Program Counter 10-bit signed literal {-512...511} 16-bit signed literal {-32768...32767} 6-bit signed literal {-16...16} Base W register {W0..W15} Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] } Destination W register  { Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] } Dividend, Divisor working register pair (direct addressing) One of 16 working registers {W0..W15} One of 16 destination working registers {W0..W15} One of 16 source working registers {W0..W15} W0 (working register used in File register instructions) Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] } Source W register { Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] } SYMBOLS USED IN OPCODE DESCRIPTIONS Description DS39995B-page 256  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 28-2: Assembly Mnemonic ADD ADD ADD ADD ADD ADD ADDC ADDC ADDC ADDC ADDC ADDC AND AND AND AND AND AND ASR ASR ASR ASR ASR ASR BCLR BCLR BCLR BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BRA BSET BSET BSET BSW BSW.C BSW.Z BTG BTG BTG BTSC BTSC BTSC f f,WREG #lit10,Wn Wb,Ws,Wd Wb,#lit5,Wd f f,WREG #lit10,Wn Wb,Ws,Wd Wb,#lit5,Wd f f,WREG #lit10,Wn Wb,Ws,Wd Wb,#lit5,Wd f f,WREG Ws,Wd Wb,Wns,Wnd Wb,#lit5,Wnd f,#bit4 Ws,#bit4 C,Expr GE,Expr GEU,Expr GT,Expr GTU,Expr LE,Expr LEU,Expr LT,Expr LTU,Expr N,Expr NC,Expr NN,Expr NOV,Expr NZ,Expr OV,Expr Expr Z,Expr Wn f,#bit4 Ws,#bit4 Ws,Wb Ws,Wb f,#bit4 Ws,#bit4 f,#bit4 Ws,#bit4 INSTRUCTION SET OVERVIEW Assembly Syntax f = f + WREG WREG = f + WREG Wd = lit10 + Wd Wd = Wb + Ws Wd = Wb + lit5 f = f + WREG + (C) WREG = f + WREG + (C) Wd = lit10 + Wd + (C) Wd = Wb + Ws + (C) Wd = Wb + lit5 + (C) f = f .AND. WREG WREG = f .AND. WREG Wd = lit10 .AND. Wd Wd = Wb .AND. Ws Wd = Wb .AND. lit5 f = Arithmetic Right Shift f WREG = Arithmetic Right Shift f Wd = Arithmetic Right Shift Ws Wnd = Arithmetic Right Shift Wb by Wns Wnd = Arithmetic Right Shift Wb by lit5 Bit Clear f Bit Clear Ws Branch if Carry Branch if Greater than or Equal Branch if Unsigned Greater than or Equal Branch if Greater than Branch if Unsigned Greater than Branch if Less than or Equal Branch if Unsigned Less than or Equal Branch if Less than Branch if Unsigned Less than Branch if Negative Branch if Not Carry Branch if Not Negative Branch if Not Overflow Branch if Not Zero Branch if Overflow Branch Unconditionally Branch if Zero Computed Branch Bit Set f Bit Set Ws Write C bit to Ws Write Z bit to Ws Bit Toggle f Bit Toggle Ws Bit Test f, Skip if Clear Bit Test Ws, Skip if Clear Description # of Words 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 # of Cycles 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 2 1 (2) 2 1 1 1 1 1 1 Status Flags Affected C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z N, Z N, Z N, Z N, Z N, Z C, N, OV, Z C, N, OV, Z C, N, OV, Z N, Z N, Z None None None None None None None None None None None None None None None None None None None None None None None None None None 1 None (2 or 3) 1 None (2 or 3)  2011 Microchip Technology Inc. DS39995B-page 257 PIC24FV32KA304 FAMILY TABLE 28-2: Assembly Mnemonic BTSS BTSS BTSS BTST BTST BTST.C BTST.Z BTST.C BTST.Z BTSTS BTSTS BTSTS.C BTSTS.Z CALL CALL CALL CLR CLR CLR CLR CLRWDT COM CLRWDT COM COM COM CP CP CP CP CP0 CP0 CP0 CPB CPB CPB CPB CPSEQ CPSGT CPSLT CPSNE DAW DEC CPSEQ CPSGT CPSLT CPSNE DAW DEC DEC DEC DEC2 DEC2 DEC2 DEC2 DISI DIV DISI DIV.SW DIV.SD DIV.UW DIV.UD EXCH FF1L FF1R EXCH FF1L FF1R f f,WREG Ws,Wd f Wb,#lit5 Wb,Ws f Ws f Wb,#lit5 Wb,Ws Wb,Wn Wb,Wn Wb,Wn Wb,Wn Wn f f,WREG Ws,Wd f f,WREG Ws,Wd #lit14 Wm,Wn Wm,Wn Wm,Wn Wm,Wn Wns,Wnd Ws,Wnd Ws,Wnd INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Syntax f,#bit4 Ws,#bit4 f,#bit4 Ws,#bit4 Ws,#bit4 Ws,Wb Ws,Wb f,#bit4 Ws,#bit4 Ws,#bit4 lit23 Wn f WREG Ws Description Bit Test f, Skip if Set Bit Test Ws, Skip if Set Bit Test f Bit Test Ws to C Bit Test Ws to Z Bit Test Ws to C Bit Test Ws to Z Bit Test then Set f Bit Test Ws to C, then Set Bit Test Ws to Z, then Set Call Subroutine Call Indirect Subroutine f = 0x0000 WREG = 0x0000 Ws = 0x0000 Clear Watchdog Timer f=f WREG = f Wd = Ws Compare f with WREG Compare Wb with lit5 Compare Wb with Ws (Wb – Ws) Compare f with 0x0000 Compare Ws with 0x0000 Compare f with WREG, with Borrow Compare Wb with lit5, with Borrow Compare Wb with Ws, with Borrow (Wb – Ws – C) Compare Wb with Wn, Skip if = Compare Wb with Wn, Skip if > Compare Wb with Wn, Skip if < Compare Wb with Wn, Skip if  Wn = Decimal Adjust Wn f = f –1 WREG = f –1 Wd = Ws – 1 f=f–2 WREG = f – 2 Wd = Ws – 2 Disable Interrupts for k Instruction Cycles Signed 16/16-bit Integer Divide Signed 32/16-bit Integer Divide Unsigned 16/16-bit Integer Divide Unsigned 32/16-bit Integer Divide Swap Wns with Wnd Find First One from Left (MSb) Side Find First One from Right (LSb) Side # of Words 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 # of Cycles Status Flags Affected 1 None (2 or 3) 1 None (2 or 3) 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Z C Z C Z Z C Z None None None None None WDTO, Sleep N, Z N, Z N, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z 1 None (2 or 3) 1 None (2 or 3) 1 None (2 or 3) 1 None (2 or 3) 1 1 1 1 1 1 1 1 18 18 18 18 1 1 1 C C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z None N, Z, C, OV N, Z, C, OV N, Z, C, OV N, Z, C, OV None C C DS39995B-page 258  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 28-2: Assembly Mnemonic GOTO GOTO GOTO INC INC INC INC INC2 INC2 INC2 INC2 IOR IOR IOR IOR IOR IOR LNK LSR LNK LSR LSR LSR LSR LSR MOV MOV MOV MOV MOV MOV MOV.b MOV MOV MOV MOV MOV.D MOV.D MUL MUL.SS MUL.SU MUL.US MUL.UU MUL.SU MUL.UU MUL NEG NEG NEG NEG NOP NOP NOPR POP POP POP POP.D POP.S PUSH PUSH PUSH PUSH.D PUSH.S f Wso Wns f Wdo Wnd INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Syntax Expr Wn f f,WREG Ws,Wd f f,WREG Ws,Wd f f,WREG #lit10,Wn Wb,Ws,Wd Wb,#lit5,Wd #lit14 f f,WREG Ws,Wd Wb,Wns,Wnd Wb,#lit5,Wnd f,Wn [Wns+Slit10],Wnd f f,WREG #lit16,Wn #lit8,Wn Wn,f Wns,[Wns+Slit10] Wso,Wdo WREG,f Wns,Wd Ws,Wnd Wb,Ws,Wnd Wb,Ws,Wnd Wb,Ws,Wnd Wb,Ws,Wnd Wb,#lit5,Wnd Wb,#lit5,Wnd f f f,WREG Ws,Wd Go to Address Go to Indirect f=f+1 WREG = f + 1 Wd = Ws + 1 f=f+2 WREG = f + 2 Wd = Ws + 2 f = f .IOR. WREG WREG = f .IOR. WREG Wd = lit10 .IOR. Wd Wd = Wb .IOR. Ws Wd = Wb .IOR. lit5 Link Frame Pointer f = Logical Right Shift f WREG = Logical Right Shift f Wd = Logical Right Shift Ws Wnd = Logical Right Shift Wb by Wns Wnd = Logical Right Shift Wb by lit5 Move f to Wn Move [Wns+Slit10] to Wnd Move f to f Move f to WREG Move 16-bit Literal to Wn Move 8-bit Literal to Wn Move Wn to f Move Wns to [Wns+Slit10] Move Ws to Wd Move WREG to f Move Double from W(ns):W(ns+1) to Wd Move Double from Ws to W(nd+1):W(nd) {Wnd+1, Wnd} = Signed(Wb) * Signed(Ws) {Wnd+1, Wnd} = Signed(Wb) * Unsigned(Ws) {Wnd+1, Wnd} = Unsigned(Wb) * Signed(Ws) {Wnd+1, Wnd} = Unsigned(Wb) * Unsigned(Ws) {Wnd+1, Wnd} = Signed(Wb) * Unsigned(lit5) {Wnd+1, Wnd} = Unsigned(Wb) * Unsigned(lit5) W3:W2 = f * WREG f=f+1 WREG = f + 1 Wd = Ws + 1 No Operation No Operation Pop f from Top-of-Stack (TOS) Pop from Top-of-Stack (TOS) to Wdo Pop from Top-of-Stack (TOS) to W(nd):W(nd+1) Pop Shadow Registers Push f to Top-of-Stack (TOS) Push Wso to Top-of-Stack (TOS) Push W(ns):W(ns+1) to Top-of-Stack (TOS) Push Shadow Registers Description # of Words 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 # of Cycles 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 Status Flags Affected None None C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z N, Z N, Z N, Z N, Z N, Z None C, N, OV, Z C, N, OV, Z C, N, OV, Z N, Z N, Z None None N, Z N, Z None None None None None N, Z None None None None None None None None None C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z None None None None None All None None None None  2011 Microchip Technology Inc. DS39995B-page 259 PIC24FV32KA304 FAMILY TABLE 28-2: Assembly Mnemonic PWRSAV RCALL PWRSAV RCALL RCALL REPEAT REPEAT REPEAT RESET RETFIE RETLW RETURN RLC RESET RETFIE RETLW RETURN RLC RLC RLC RLNC RLNC RLNC RLNC RRC RRC RRC RRC RRNC RRNC RRNC RRNC SE SETM SE SETM SETM SETM SL SL SL SL SL SL SUB SUB SUB SUB SUB SUB SUBB SUBB SUBB SUBB SUBB SUBB SUBR SUBR SUBR SUBR SUBR SUBBR SUBBR SUBBR SUBBR SUBBR SWAP SWAP.b SWAP TBLRDH TBLRDH f f,WREG Ws,Wd f f,WREG Ws,Wd f f,WREG Ws,Wd f f,WREG Ws,Wd Ws,Wnd f WREG Ws f f,WREG Ws,Wd Wb,Wns,Wnd Wb,#lit5,Wnd f f,WREG #lit10,Wn Wb,Ws,Wd Wb,#lit5,Wd f f,WREG #lit10,Wn Wb,Ws,Wd Wb,#lit5,Wd f f,WREG Wb,Ws,Wd Wb,#lit5,Wd f f,WREG Wb,Ws,Wd Wb,#lit5,Wd Wn Wn Ws,Wd #lit10,Wn INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Syntax #lit1 Expr Wn #lit14 Wn Description Go into Sleep or Idle mode Relative Call Computed Call Repeat Next Instruction lit14 + 1 times Repeat Next Instruction (Wn) + 1 times Software Device Reset Return from Interrupt Return with Literal in Wn Return from Subroutine f = Rotate Left through Carry f WREG = Rotate Left through Carry f Wd = Rotate Left through Carry Ws f = Rotate Left (No Carry) f WREG = Rotate Left (No Carry) f Wd = Rotate Left (No Carry) Ws f = Rotate Right through Carry f WREG = Rotate Right through Carry f Wd = Rotate Right through Carry Ws f = Rotate Right (No Carry) f WREG = Rotate Right (No Carry) f Wd = Rotate Right (No Carry) Ws Wnd = Sign-Extended Ws f = FFFFh WREG = FFFFh Ws = FFFFh f = Left Shift f WREG = Left Shift f Wd = Left Shift Ws Wnd = Left Shift Wb by Wns Wnd = Left Shift Wb by lit5 f = f – WREG WREG = f – WREG Wn = Wn – lit10 Wd = Wb – Ws Wd = Wb – lit5 f = f – WREG – (C) WREG = f – WREG – (C) Wn = Wn – lit10 – (C) Wd = Wb – Ws – (C) Wd = Wb – lit5 – (C) f = WREG – f WREG = WREG – f Wd = Ws – Wb Wd = lit5 – Wb f = WREG – f – (C) WREG = WREG – f – (C) Wd = Ws – Wb – (C) Wd = lit5 – Wb – (C) Wn = Nibble Swap Wn Wn = Byte Swap Wn Read Prog to Wd # of Words 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 # of Cycles 1 2 2 1 1 1 3 (2) 3 (2) 3 (2) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 Status Flags Affected WDTO, Sleep None None None None None None None None C, N, Z C, N, Z C, N, Z N, Z N, Z N, Z C, N, Z C, N, Z C, N, Z N, Z N, Z N, Z C, N, Z None None None C, N, OV, Z C, N, OV, Z C, N, OV, Z N, Z N, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z C, DC, N, OV, Z None None None DS39995B-page 260  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 28-2: Assembly Mnemonic TBLRDL TBLWTH TBLWTL ULNK XOR TBLRDL TBLWTH TBLWTL ULNK XOR XOR XOR XOR XOR ZE ZE f f,WREG #lit10,Wn Wb,Ws,Wd Wb,#lit5,Wd Ws,Wnd INSTRUCTION SET OVERVIEW (CONTINUED) Assembly Syntax Ws,Wd Ws,Wd Ws,Wd Description Read Prog to Wd Write Ws to Prog Write Ws to Prog Unlink Frame Pointer f = f .XOR. WREG WREG = f .XOR. WREG Wd = lit10 .XOR. Wd Wd = Wb .XOR. Ws Wd = Wb .XOR. lit5 Wnd = Zero-Extend Ws # of Words 1 1 1 1 1 1 1 1 1 1 # of Cycles 2 2 2 1 1 1 1 1 1 1 Status Flags Affected None None None None N, Z N, Z N, Z N, Z N, Z C, Z, N  2011 Microchip Technology Inc. DS39995B-page 261 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 262  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 29.0 ELECTRICAL CHARACTERISTICS This section provides an overview of the PIC24FV32KA304 family electrical characteristics. Additional information will be provided in future revisions of this document as it becomes available. Absolute maximum ratings for the PIC24FV32KA304 family are listed below. Exposure to these maximum rating conditions for extended periods may affect device reliability. Functional operation of the device at these, or any other conditions above the parameters indicated in the operation listings of this specification, is not implied. Absolute Maximum Ratings(†) Ambient temperature under bias.............................................................................................................-40°C to +125°C Storage temperature .............................................................................................................................. -65°C to +150°C Voltage on VDD with respect to VSS (PIC24FVXXKA30X) ....................................................................... -0.3V to +6.5V Voltage on VDD with respect to VSS (PIC24FXXKA30X) .......................................................................... -0.3V to +4.5V Voltage on any combined analog and digital pin, with respect to VSS ........................................... -0.3V to (VDD + 0.3V) Voltage on any digital only pin with respect to VSS ....................................................................... -0.3V to (VDD + 0.3V) Voltage on MCLR/VPP pin with respect to VSS ......................................................................................... -0.3V to +9.0V Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin(1) ...........................................................................................................................250 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk by all ports .......................................................................................................................200 mA Maximum current sourced by all ports(1) ...............................................................................................................200 mA Note 1: Maximum allowable current is a function of device maximum power dissipation (see Table 29-1). NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.  2011 Microchip Technology Inc. DS39995B-page 263 PIC24FV32KA304 FAMILY 29.1 DC Characteristics PIC24FV32KA304 VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL) FIGURE 29-1: 5.5V 3.20V Voltage (VDD) 5.5V 3.20V 2.00V 8 MHz Frequency Note: 32 MHz For frequencies between 8 MHz and 32 MHz, FMAX = 20 MHz *(VDD – 2.0) + 8 MHz. FIGURE 29-2: PIC24F32KA304 FAMILY VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL) 3.60V 3.00V Voltage (VDD) 3.60V 3.00V 1.80V 8 MHz Frequency Note: 32 MHz For frequencies between 8 MHz and 32 MHz, FMAX = 20 MHz * (VDD – 1.8) + 8 MHz. DS39995B-page 264  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-1: THERMAL OPERATING CONDITIONS Rating Operating Junction Temperature Range Operating Ambient Temperature Range Power Dissipation: Internal Chip Power Dissipation: PINT = VDD x (IDD –  IOH) I/O Pin Power Dissipation: PI/O =  ({VDD – VOH} x IOH) +  (VOL x IOL) Maximum Allowed Power Dissipation PDMAX (TJ – TA)/JA W Symbol TJ TA Min -40 -40 Typ — — Max +125 +85 Unit °C °C PD PINT + PI/O W TABLE 29-2: THERMAL PACKAGING CHARACTERISTICS Characteristic Symbol JA JA JA JA JA JA JA JA JA JA Typ 62.4 60 108 71 75 80.2 43 32 29 — Max — — — — — — — — — — Unit °C/W °C/W °C/W °C/W °C/W °C/W °C/W °C/W °C/W °C/W Notes 1 1 1 1 1 1 1 1 1 1 Package Thermal Resistance, 20-Pin SPDIP Package Thermal Resistance, 28-Pin SPDIP Package Thermal Resistance, 20-Pin SSOP Package Thermal Resistance, 28-Pin SSOP Package Thermal Resistance, 20-Pin SOIC Package Thermal Resistance, 28-Pin SOIC Package Thermal Resistance, 20-Pin QFN Package Thermal Resistance, 28-Pin QFN Package Thermal Resistance, 44-Pin QFN Package Thermal Resistance, 48-Pin UQFN Note 1: Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations. TABLE 29-3: DC CHARACTERISTICS: TEMPERATURE AND VOLTAGE SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min 1.8 2.0 1.5 VSS Typ(1) — — — — Max Units 3.6 5.5V — 0.7 V V V V Conditions For F devices For FV devices DC CHARACTERISTICS Para m No. DC10 DC12 DC16 Symbol VDD VDR VPOR Characteristic Supply Voltage RAM Data Retention Voltage(2) VDD Start Voltage to Ensure Internal Power-on Reset Signal VDD Rise Rate to Ensure Internal Power-on Reset Signal DC17 SVDD 0.05 — — V/ms 0-3.3V in 0.1s 0-2.5V in 60 ms Note 1: 2: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. This is the limit to which VDD can be lowered without losing RAM data.  2011 Microchip Technology Inc. DS39995B-page 265 PIC24FV32KA304 FAMILY TABLE 29-4: HIGH/LOW–VOLTAGE DETECT CHARACTERISTICS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Param Symbol No. DC18 VHLVD Characteristic HLVD Voltage on VDD HLVDL = 0000(2) Transition HLVDL = 0001 HLVDL = 0010 HLVDL = 0011 HLVDL = 0100 HLVDL = 0101 HLVDL = 0110 HLVDL = 0111 HLVDL = 1000 HLVDL = 1001 HLVDL = 1010 (1) Min — 1.88 2.09 2.25 2.35 2.55 2.80 2.95 3.09 3.27 3.46 3.62 3.91 4.18 4.49 Typ — — — — — — — — — — — — — — — Max 1.90 2.13 2.35 2.53 2.62 2.84 3.10 3.25 3.41 3.59 3.79 4.01 4.26 4.55 4.87 Units V V V V V V V V V V V V V V V Conditions HLVDL = 1011(1) HLVDL = 1100 HLVDL = Note 1: 2: (1) HLVDL = 1101(1) 1110(1) These trip points should not be used on PIC24F32KA304 devices. This trip point should not be used on PIC24FVXXKA30X devices. TABLE 29-5: BOR TRIP POINTS 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX -40°C  TA  +85°C for Industrial Characteristic BOR Voltage on VDD Transition BORV = 00 BORV = 01 BORV = 10 BORV = 11 BORV = 11 Min — 2.90 2.53 1.75 1.95 Typ — 3 2.7 Max Units — 3.38 3.07 — V V V V Note 2 Note 3 Conditions Valid for LPBOR and DSBOR, Note 1 Standard Operating Conditions: Operating temperature Param Sym No. DC19 1.85 2.05 2.05 2.16 Note 1: 2: 3: LPBOR re-arms the POR circuit but does not cause a BOR. Valid for PIC24F (3.3V) devices. Valid for PIC24FV (5V) devices. DS39995B-page 266  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-6: DC CHARACTERISTICS: OPERATING CURRENT (IDD) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical Max Units Conditions DC CHARACTERISTICS Parameter No. Device IDD Current DC20 — -40°C DC20a — +25°C 269.00 µA 2.0V DC20b — +60°C DC20c 450.00 +85°C PIC24FV32KA3XX DC20d — -40°C DC20e — +25°C 465.00 µA 5.0V DC20f — +60°C DC20g 830.00 +85°C 0.5 MIPS, FOSC = 1 MHz DC20h — -40°C DC20i — +25°C 200.00 µA 1.8V DC20j — +60°C DC20k 330.00 +85°C PIC24F32KA3XX DC20l — -40°C DC20m — +25°C 410.00 µA 3.3V DC20n — +60°C DC20o 750.00 +85°C DC22 — -40°C DC22a — +25°C 490.00 µA 2.0V DC22b — +60°C DC22c — +85°C PIC24FV32KA3XX DC22d — -40°C DC22e — +25°C 880.00 µA 5.0V DC22f — +60°C DC22g — +85°C 1 MIPS, FOSC = 2 MHz DC22h — -40°C DC22i — +25°C 407.00 µA 1.8V DC22j — +60°C DC22k — +85°C PIC24F32KA3XX DC22l — -40°C DC22m — +25°C 800.00 µA 3.3V DC22n — +60°C DC22o — +85°C Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices.  2011 Microchip Technology Inc. DS39995B-page 267 PIC24FV32KA304 FAMILY TABLE 29-6: DC CHARACTERISTICS: OPERATING CURRENT (IDD) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical Max Units Conditions DC CHARACTERISTICS Parameter No. Device IDD Current (Continued) DC24 — -40°C DC24a — +25°C PIC24FV32KA3XX 13.00 mA 5.0V DC24b — +60°C DC24c 20.00 +85°C 16 MIPS, FOSC = 32 MHz DC24d — -40°C DC24e — +25°C PIC24F32KA3XX 12.00 mA 3.3V DC24f — +60°C DC24g 18.00 +85°C DC26 — -40°C DC26a — +25°C 2.00 mA 2.0V DC26b — +60°C DC26c — +85°C PIC24FV32KA3XX DC26d — -40°C DC26e — +25°C 3.50 mA 5.0V DC26f — +60°C DC26g — +85°C FRC (4 MIPS), FOSC = 8 MHz DC26h — -40°C DC26i — +25°C 1.80 mA 1.8V DC26j — +60°C DC26k — +85°C PIC24F32KA3XX DC26l — -40°C DC26m — +25°C 3.40 mA 3.3V DC26n — +60°C DC26o — +85°C DC30 — -40°C DC30a — +25°C 48.00 µA 2.0V DC30b — +60°C DC30c 250.00 +85°C PIC24FV32KA3XX DC30d — -40°C DC30e — +25°C 75.00 µA 5.0V DC30f — +60°C LPRC DC30g 275.00 +85°C (15.5 KIPS), DC30h — -40°C FOSC = 31 kHz DC30i — +25°C 8.10 µA 1.8V DC30j — +60°C DC30k 28.00 +85°C PIC24F32KA3XX DC30l — -40°C DC30m — +25°C 13.50 µA 3.3V DC30n — +60°C DC30o 55.00 +85°C Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices. DS39995B-page 268  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-7: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical Max Units Conditions DC CHARACTERISTICS Parameter No. Idle Current (IIDLE) DC40 DC40a DC40b DC40c DC40d DC40e DC40f DC40g DC40h DC40i DC40j DC40k DC40l DC40m DC40n DC40o DC42 DC42a DC42b DC42c DC42d DC42e DC42f DC42g DC42h DC42i DC42j DC42k DC42l DC42m DC42n DC42o DC44 DC44a DC44b DC44c DC44d DC44e DC44f DC44g PIC24F32KA3XX 2.90 PIC24FV32KA3XX 3.10 PIC24F32KA3XX 180.00 95.00 PIC24FV32KA3XX 260.00 165.00 PIC24F32KA3XX 90.00 50.00 PIC24FV32KA3XX 160.00 120.00 — — — 200.00 — — — 430.00 — — — 100.00 — — — 370.00 — — — — — — — — — — — — — — — — — — — 6.50 — — — 6.00 mA mA µA µA µA µA µA µA µA µA -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C 3.3V 5.0V 16 MIPS, FOSC = 32 MHz 3.3V 1.8V 5.0V 1 MIPS, FOSC = 2 MHz 2.0V 3.3V 1.8V 5.0V 0.5 MIPS, FOSC = 1 MHz 2.0V Device Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices.  2011 Microchip Technology Inc. DS39995B-page 269 PIC24FV32KA304 FAMILY TABLE 29-7: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical Max Units Conditions DC CHARACTERISTICS Parameter No. DC46 DC46a DC46b DC46c DC46d DC46e DC46f DC46g DC46h DC46i DC46j DC46k DC46l DC46m DC46n DC46o DC50 DC50a DC50b DC50c DC50d DC50e DC50f DC50g DC50h DC50i DC50j DC50k DC50l DC50m DC50n DC50o PIC24F32KA3XX 4.00 2.20 PIC24FV32KA3XX 70.00 60.00 PIC24F32KA3XX 1.00 0.55 PIC24FV32KA3XX 1.00 0.65 Device Idle Current (IIDLE) (Continued) — — — — — — — — — — — — — — — — — — — 200.00 — — — 225.00 — — — 18.00 — — — 40.00 µA µA µA µA mA mA mA mA -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C 3.3V 1.8V 5.0V LPRC (15.5 KIPS), FOSC = 31 kHz 2.0V 3.3V 1.8V 5.0V FRC (4 MIPS), FOSC = 8 MHz 2.0V Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices. DS39995B-page 270  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical(1) Max Units Conditions DC CHARACTERISTICS Parameter No. DC60 DC60a DC60b DC60c DC60d DC60e DC60f DC60g DC60h DC60i DC60j DC60k DC60l DC60m DC60n DC60o DC61 DC61a DC61b DC61c DC61d DC61e DC61f DC61g PIC24FV32KA3XX 0.35 0.25 PIC24F32KA3XX 0.040 0.025 PIC24FV32KA3XX 6.00 6.00 Device Power-Down Current (IPD) — 8.00 8.50 9.00 — 8.00 9.00 10.00 — 0.80 1.50 2.00 — 1.00 2.00 3.00 — — — — — — — 3.00 µA µA µA µA µA µA -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C 5.0V 2.0V Low-Voltage Sleep Mode(2) 3.3V 1.8V 5.0V Sleep Mode(2) 2.0V Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, 25°C (PIC24F32KA3XX); 5.0V, 25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’, and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: Current applies to Sleep only. 5: Current applies to Sleep and Deep Sleep. 6: Current applies to Deep Sleep only.  2011 Microchip Technology Inc. DS39995B-page 271 PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical(1) Max Units Conditions DC CHARACTERISTICS Parameter No. DC70 DC70a DC70b DC70c DC70d DC70e DC70f DC70g DC70h DC70i DC70j DC70k DC70l DC70m DC70n DC70o PIC24F32KA3XX 0.08 0.02 PIC24FV32KA3XX 0.10 0.03 Device Power-Down Current (IPD) (Continued) — — — — — — — 1.20 – — — — — — — 1.20 µA µA µA µA -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C 3.3V 1.8V 5.0V Deep Sleep Mode 2.0V Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, 25°C (PIC24F32KA3XX); 5.0V, 25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’, and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: Current applies to Sleep only. 5: Current applies to Sleep and Deep Sleep. 6: Current applies to Deep Sleep only. DS39995B-page 272  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical(1) Max Units Conditions DC CHARACTERISTICS Parameter No. DC71 DC71a DC71b DC71c DC71d DC71e DC71f DC71g DC71h DC71i DC71j DC71k DC71l DC71m DC71n DC71o DC72 DC72a DC72b DC72c DC72d DC72e DC72f DC72g DC72h DC72i DC72j DC72k DC72l DC72m DC72n DC72o PIC24F32KA3XX 1.00 0.70 PIC24FV32KA3XX 1.50 0.80 PIC24F32KA3XX 0.70 0.50 PIC24FV32KA3XX 0.70 0.50 Device Power-Down Current (IPD) (Continued) — — — — — — — 1.5 — — — — — — — 1.5 — — — — — — — 2.0 — — — — — — — 1.5 µA µA µA µA µA µA µA µA -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C 3.3V 1.8V 5.0V 32 kHz Crystal with RTCC, DSWDT or Timer1: SOSC; (SOSCSEL = 0)(3,5) 2.0V 3.3V 1.8V 5.0V Watchdog Timer Current: WDT(3,4) 2.0V Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, 25°C (PIC24F32KA3XX); 5.0V, 25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’, and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: Current applies to Sleep only. 5: Current applies to Sleep and Deep Sleep. 6: Current applies to Deep Sleep only.  2011 Microchip Technology Inc. DS39995B-page 273 PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical(1) Max Units Conditions DC CHARACTERISTICS Parameter No. DC75 DC75a DC75b DC75c DC75d DC75e DC75f DC75g DC75h DC75i DC75j DC75k DC75l DC75m DC75n DC75o DC76 DC76a DC76b DC76c DC76d DC76e DC76f DC76g DC76h DC76i DC76j DC76k DC76l DC76m DC76n DC76o PIC24F32KA3XX 6.00 5.60 PIC24FV32KA3XX 6.50 5.60 PIC24F32KA3XX 7.50 4.90 PIC24FV32KA3XX 8.10 5.40 Device Power-Down Current (IPD) (Continued) — — — — — — — 14.00 — — — — — — — 14.00 — — — — — — — 11.20 — — — — — — — 11.20 µA µA µA µA µA µA µA µA -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C 3.3V 1.8V 5.0V BOR(3,4) 2.0V 3.3V 1.8V 5.0V HLVD(3,4) 2.0V Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, 25°C (PIC24F32KA3XX); 5.0V, 25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’, and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: Current applies to Sleep only. 5: Current applies to Sleep and Deep Sleep. 6: Current applies to Deep Sleep only. DS39995B-page 274  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Typical(1) Max Units Conditions DC CHARACTERISTICS Parameter No. DC78 DC78a DC78b DC78c DC78d DC78e DC78f DC78g DC78h DC78i DC78j DC78k DC78l DC78m DC78n DC78o DC80 DC80a DC80b DC80c DC80d DC80e DC80f DC80g DC80h DC80i DC80j DC80k DC80l DC80m DC80n DC80o PIC24F32KA3XX 0.35 0.20 PIC24FV32KA3XX 0.70 0.20 PIC24F32KA3XX 0.05 0.03 PIC24FV32KA3XX 0.05 0.03 Device Power-Down Current (IPD) (Continued) — — — — — — — 0.20 — — — — — — — 0.20 — — — — — — — 1.5 — — — — — — — 0.8 µA µA µA µA µA µA µA µA -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C -40°C +25°C +60°C +85°C 3.3V 1.8V 5.0V Deep Sleep WDT: DSWDT (LPRC)(3,6) 2.0V 3.3V 1.8V 5.0V LPBOR/Deep Sleep BOR(3,5) 2.0V Legend: Unshaded rows are PIC24F32KA3XX devices, and shaded rows are PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, 25°C (PIC24F32KA3XX); 5.0V, 25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’, and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: Current applies to Sleep only. 5: Current applies to Sleep and Deep Sleep. 6: Current applies to Deep Sleep only.  2011 Microchip Technology Inc. DS39995B-page 275 PIC24FV32KA304 FAMILY TABLE 29-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min — VSS VSS VSS VSS VSS VSS — 0.8 VDD 0.8 VDD 0.8 VDD 0.7 VDD 0.7 VDD 0.7 VDD 0.7 VDD 2.1 50 Typ(1) — — — — — — — — — — — — — — — — 250 Max — 0.2 VDD 0.2 VDD 0.2 VDD 0.2 VDD 0.3 VDD 0.8 — VDD VDD VDD VDD VDD VDD VDD VDD 500 Units — V V V V V V — V V V V V V V V A 2.5V  VPIN  VDD VDD = 3.3V, VPIN = VSS SMBus disabled SMBus enabled Conditions DC CHARACTERISTICS Param No. DI10 DI15 DI16 DI17 DI18 DI19 VIH DI20 Sym VIL Characteristic Input Low Voltage(4) I/O Pins MCLR OSCI (XT mode) OSCI (HS mode) I/O Pins with I2C™ Buffer I/O Pins with SMBus Buffer Input High Voltage(4) I/O Pins: with Analog Functions Digital Only MCLR OSCI (XT mode) OSCI (HS mode) I/O Pins with I2C Buffer: with Analog Functions Digital Only I/O Pins with SMBus DI25 DI26 DI27 DI28 DI29 DI30 IIL DI50 DI55 DI56 Note 1: 2: ICNPU CNx Pull-up Current Input Leakage Current(2,3) I/O Ports MCLR OSCI — — — 0.05 — — 0.1 0.1 5 A A A VSS  VPIN  VDD, Pin at high-impedance VSS VPIN VDD VSS VPIN VDD, XT and HS modes 3: 4: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. Refer to Table 1-3 for I/O pin buffer types. DS39995B-page 276  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS DC CHARACTERISTICS Param No. DO10 Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min — — — — DO16 OSC2/CLKO — — — VOH DO20 Output High Voltage All I/O Pins 3.8 3 1.6 DO26 OSC2/CLKO 3.8 3 1.6 Note 1: — — — — — — — — — — — — V V V V V V IOH = -3.5 mA IOH = -3.0 mA IOH = -1.0 mA IOH = -2.0 mA IOH = -1.0 mA IOH = -0.5 mA VDD = 4.5V VDD = 3.6V VDD = 2.0V VDD = 4.5V VDD = 3.6V VDD = 2.0V Typ(1) — — — — — — — 0.4 0.4 0.4 0.4 0.4 0.4 V V V V V V IOL = 8.0 mA IOL = 4.0 mA IOL = 3.5 mA IOL = 2.0 mA IOL = 1.2 mA IOL = 0.4 mA VDD = 4.5V VDD = 3.6V VDD = 2.0V VDD = 4.5V VDD = 3.6V VDD = 2.0V Max Units Conditions Sym VOL Characteristic Output Low Voltage All I/O Pins Data in “Typ” column is at 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. TABLE 29-11: DC CHARACTERISTICS: PROGRAM MEMORY DC CHARACTERISTICS Param No. D130 D131 Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min Typ(1) Max Units Conditions Sym Characteristic Program Flash Memory EP VPR Cell Endurance VDD for Read Self-Timed Write Cycle Time 10,000(2) VMIN — 40 — — — 2 — 10 — 3.6 — — — E/W V ms Year mA Provided no other specifications are violated VMIN = Minimum operating voltage D133A TIW D134 D135 Note 1: 2: TRETD Characteristic Retention IDDP Supply Current During Programming Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Self-write and block erase.  2011 Microchip Technology Inc. DS39995B-page 277 PIC24FV32KA304 FAMILY TABLE 29-12: DC CHARACTERISTICS: DATA EEPROM MEMORY DC CHARACTERISTICS Param No. D140 D141 D143A D143B Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min Typ(1) Max Units Conditions Sym Characteristic Data EEPROM Memory EPD VPRD TIWD TREF Cell Endurance VDD for Read Self-Timed Write Cycle Time Number of Total Write/Erase Cycles Before Refresh 100,000 VMIN — — — — 4 10M — 3.6 — — E/W V ms E/W VMIN = Minimum operating voltage D144 D145 Note 1: TRETDD Characteristic Retention IDDPD Supply Current during Programming 40 — — 7 — — Year mA Provided no other specifications are violated Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. TABLE 29-13: COMPARATOR DC SPECIFICATIONS Operating Conditions: 2.0V < VDD < 3.6V, -40°C < TA < +85°C (unless otherwise stated) Param No. D300 D301 D302 Symbol VIOFF VICM CMRR Characteristic Input Offset Voltage* Input Common Mode Voltage* Common Mode Rejection Ratio* Min — 0 55 Typ 20 — — Max 40 VDD — Units mV V dB Comments * Parameters are characterized but not tested. TABLE 29-14: COMPARATOR VOLTAGE REFERENCE DC SPECIFICATIONS Operating Conditions: 2.0V < VDD < 3.6V, -40°C < TA < +85°C (unless otherwise stated) Param No. VRD310 VRD311 VRD312 Symbol CVRES CVRAA CVRUR Characteristic Resolution Absolute Accuracy Unit Resistor Value (R) Min — — — Typ — — 2k Max VDD/32 AVDD – 1.5 — Units LSb LSb  Comments DS39995B-page 278  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-15: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS Operating Conditions: -40°C < TA < +85°C (unless otherwise stated) Param Symbol No. VBG TBG VRGOUT CEFC Characteristics Band Gap Reference Voltage Band Gap Reference Start-up Time Regulator Output Voltage External Filter Capacitor Value Min 0.973 — 3.1 4.7 Typ 1.024 1 3.3 10 Max 1.075 — 3.6 — Units V ms V F Series resistance < 3 Ohm recommended; < 5 Ohm required. Comments VLVR Low-Voltage Regulator Output Voltage — 2.6 — V TABLE 29-16: CTMU CURRENT SOURCE SPECIFICATIONS DC CHARACTERISTICS Param No. Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min — — — — — — Typ(1) Max 550 5.5 55 550 .76 3 — — — — — — Units nA A A A V mV/°C Comments CTMUICON = 00 CTMUICON = 01 CTMUICON = 10 CTMUICON = 11, Note 2 2.5V < VDD < VDDMAX Conditions Sym Characteristic IOUT1 CTMU Current Source, Base Range IOUT2 CTMU Current Source, 10x Range IOUT3 CTMU Current Source, 100x Range IOUT4 CTMU Current Source, 1000x Range VF V Note 1: 2: Temperature Diode Forward Voltage Voltage Change per Degree Celsius Nominal value at center point of current trim range (CTMUICON = 000000). On PIC24F32KA parts, the current output is limited to the typ. current value when IOT4 is chosen. Do not use this current range with temperature sensing diode.  2011 Microchip Technology Inc. DS39995B-page 279 PIC24FV32KA304 FAMILY 29.2 AC Characteristics and Timing Parameters The information contained in this section defines the PIC24FV32KA304 family AC characteristics and timing parameters. TABLE 29-17: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC AC CHARACTERISTICS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature-40°C  TA  +85°C for Industrial Operating voltage VDD range as described in Section 29.1 “DC Characteristics”. FIGURE 29-3: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 2 – for OSCO Load Condition 1 – for all pins except OSCO VDD/2 RL Pin VSS CL Pin VSS CL RL = 464 CL = 50 pF for all pins except OSCO 15 pF for OSCO output TABLE 29-18: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS Param Symbol No. DO50 COSC2 Characteristic OSCO/CLKO pin Min — Typ(1) — Max 15 Units pF Conditions In XT and HS modes when external clock is used to drive OSCI EC mode In I2C™ mode DO56 DO58 Note 1: CIO CB All I/O Pins and OSCO SCLx, SDAx — — — — 50 400 pF pF Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. DS39995B-page 280  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY FIGURE 29-4: Q4 EXTERNAL CLOCK TIMING Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 OSCI OS20 OS25 OS30 OS30 OS31 OS31 CLKO OS40 OS41 TABLE 29-19: EXTERNAL CLOCK TIMING REQUIREMENTS AC CHARACTERISTICS Param Sym No. OS10 Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min DC 4 0.2 4 4 31 — 62.5 0.45 x TOSC — — — Typ(1) — — — — — — — — — — 6 6 Max 32 8 4 25 8 33 — DC — 20 10 10 Units MHz MHz MHz MHz MHz kHz — ns ns ns ns ns EC EC EC ECPLL XT HS XTPLL SOSC See Parameter OS10 for FOSC value Conditions Characteristic FOSC External CLKI Frequency (External clocks allowed only in EC mode) Oscillator Frequency OS20 OS25 OS30 OS31 OS40 OS41 TOSC TOSC = 1/FOSC TCY Instruction Cycle Time(2) TosL, External Clock in (OSCI) TosH High or Low Time TosR, External Clock in (OSCI) TosF Rise or Fall Time TckR TckF CLKO Rise Time(3) CLKO Fall Time(3) Note 1: 2: 3: Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “Min.” values with an external clock applied to the OSCI/CLKI pin. When an external clock input is used, the “Max.” cycle time limit is “DC” (no clock) for all devices. Measurements are taken in EC mode. The CLKO signal is measured on the OSCO pin. CLKO is low for the Q1-Q2 period (1/2 TCY) and high for the Q3-Q4 period (1/2 TCY).  2011 Microchip Technology Inc. DS39995B-page 281 PIC24FV32KA304 FAMILY TABLE 29-20: PLL CLOCK TIMING SPECIFICATIONS AC CHARACTERISTICS Param No. OS50 OS51 OS52 OS53 Note 1: 2: Characteristic(1) PLL Input Frequency Range PLL Output Frequency Range Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min 4 16 — -2 Typ(2) — — 1 1 Max 8 32 2 2 Units MHz MHz ms % Measured over 100 ms period Conditions ECPLL, HSPLL modes, -40°C  TA  +85°C -40°C  TA  +85°C Sym FPLLI FSYS TLOCK PLL Start-up Time (Lock Time) DCLK CLKO Stability (Jitter) These parameters are characterized but not tested in manufacturing. Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only and are not tested. TABLE 29-21: AC CHARACTERISTICS: INTERNAL FRC ACCURACY AC CHARACTERISTICS Param No. F20 Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min Typ Max Units Conditions Characteristic Internal FRC Accuracy @ 8 MHz(1) FRC -2 -5 — — +2 +5 % % +25°C 3.0V  VDD  3.6V, F Device 3.2V  VDD  5.5V, FV Device -40°C  TA +85°C 1.8V  VDD  3.6V, F Device 2.0V  VDD  5.5V, FV Device Note 1: Frequency calibrated at 25°C and 3.3V. OSCTUN bits can be used to compensate for temperature drift. TABLE 29-22: AC CHARACTERISTICS: INTERNAL RC ACCURACY AC CHARACTERISTICS Param No. F21 Note 1: Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min Typ Max Units Conditions Characteristic LPRC @ 31 kHz(1) -15 — 15 % Change of LPRC frequency as VDD changes. TABLE 29-23: INTERNAL RC OSCILLATOR SPECIFICATIONS AC CHARACTERISTICS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Min — — Typ 5 70 Max — — Units s s Conditions Param No. Sym TFRC Characteristic(1) FRC Start-up Time TLPRC LPRC Start-up Time DS39995B-page 282  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY FIGURE 29-5: CLKO AND I/O TIMING CHARACTERISTICS I/O Pin (Input) DI35 DI40 I/O Pin (Output) Old Value DO31 DO32 Note: Refer to Figure 29-3 for load conditions. New Value TABLE 29-24: CLKO AND I/O TIMING REQUIREMENTS AC CHARACTERISTICS Param No. DO31 DO32 DI35 DI40 Note 1: Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Min — — 20 2 Typ(1) 10 10 — — Max 25 25 — — Units ns ns ns TCY Conditions Sym TIOR TIOF TINP TRBP Characteristic Port Output Rise Time Port Output Fall Time INTx pin High or Low Time (output) CNx High or Low Time (input) Data in “Typ” column is at 3.3V, 25°C (PIC24F32KA3XX); 5.0V, 25°C (PIC24FV32KA3XX), unless otherwise stated.  2011 Microchip Technology Inc. DS39995B-page 283 PIC24FV32KA304 FAMILY TABLE 29-25: COMPARATOR TIMINGS Param No. 300 301 * Note 1: Symbol TRESP TMC2OV Characteristic Response Time*(1) Comparator Mode Change to Output Valid* Min — — Typ 150 — Max 400 10 Units ns s Comments Parameters are characterized but not tested. Response time measured with one comparator input at (VDD – 1.5)/2, while the other input transitions from VSS to VDD. TABLE 29-26: COMPARATOR VOLTAGE REFERENCE SETTLING TIME SPECIFICATIONS Param No. VR310 Note 1: Symbol TSET Characteristic Settling Time(1) Min — Typ — Max 10 Units s Comments Settling time measured while CVRSS = 1 and CVR bits transition from ‘0000’ to ‘1111’. DS39995B-page 284  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-27: ADC MODULE SPECIFICATIONS AC CHARACTERISTICS Param No. AD01 Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Characteristic Min. Typ Max. Units Conditions Symbol Device Supply AVDD Module VDD Supply Greater of VDD – 0.3 or 1.8 VSS – 0.3 AVSS + 1.7 AVSS AVSS – 0.3 — Lesser of VDD + 0.3 or 3.6 VSS + 0.3 AVDD AVDD – 1.7 AVDD + 0.3 V AD02 AD05 AD06 AD07 AVSS VREFH VREFL VREF Module VSS Supply Reference Voltage High Reference Voltage Low Absolute Reference Voltage Full-Scale Input Span Absolute Input Voltage Absolute VINL Input Voltage Recommended Impedance of Analog Voltage Source Resolution Integral Nonlinearity Differential Nonlinearity Gain Error Offset Error Monotonicity(1) — — — — V V V V Reference Inputs Analog Input AD10 AD11 AD12 AD17 VINH-VINL VIN VINL RIN VREFL AVSS – 0.3 AVSS – 0.3 — — — — VREFH AVDD + 0.3 AVDD/2 2.5K V V V  12-bit (Note 2) ADC Accuracy AD20b NR AD21b INL AD22b DNL AD23b GERR AD24b EOFF AD25b Note 1: 2: — — — — — — 12 ±1 ±1 ±1 ±1 — — ±9 ±5 ±9 ±5 — bits LSb LSb LSb LSb — VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V Guaranteed The ADC conversion result never decreases with an increase in the input voltage. Measurements are taken with external VREF+ and VREF- used as the ADC voltage reference.  2011 Microchip Technology Inc. DS39995B-page 285 PIC24FV32KA304 FAMILY TABLE 29-28: ADC CONVERSION TIMING REQUIREMENTS(1) AC CHARACTERISTICS Param Symbol No. AD50 AD51 TAD TRC Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial Characteristic Min. Typ Max. Units Conditions Clock Parameters ADC Clock Period ADC Internal RC Oscillator Period Conversion Time Throughput Rate Sample Time Acquisition Time Switching Time from Convert to Sample Discharge Time Sample Start Delay from Setting Sample bit (SAMP) 75 — — 250 — — ns ns TCY = 75 ns, AD1CON3 in default state Conversion Rate AD55 AD56 AD57 AD58 AD59 AD60 AD61 Note 1: 2: 3: TCONV FCNV TSAMP TACQ TSWC TDIS TPSS — — — 750 — 0.5 2 12 — 1 — — — — — 100 — — (Note 3) — 3 TAD TAD TAD ksps TAD ns (Note 2) AVDD  2.7V Clock Parameters Because the sample caps will eventually lose charge, clock rates below 10 kHz can affect linearity performance, especially at elevated temperatures. The time for the holding capacitor to acquire the “New” input voltage when the voltage changes full scale after the conversion (VDD to VSS or VSS to VDD). On the following cycle of the device clock. DS39995B-page 286  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY TABLE 29-29: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER, AND BROWN-OUT RESET TIMING REQUIREMENTS Standard Operating Conditions: AC CHARACTERISTICS Operating temperature Param Symbol No. SY10 SY11 SY12 SY13 TmcL TPWRT TPOR TIOZ Characteristic MCLR Pulse Width (low) Power-up Timer Period Power-on Reset Delay I/O High-Impedance from MCLR Low or Watchdog Timer Reset Watchdog Timer Time-out Period Brown-out Reset Pulse Width Internal State Reset Time PLL Start-up Time Oscillator Start-up Time Wake-up from Deep Sleep Time Program Memory Wake-up Time Low-Voltage Regulator Wake-up Time Min. 2 50 1 — Typ(1) — 64 5 — Max. — 90 10 100 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX -40°C  TA  +85°C for Industrial Units s ms s ns Conditions SY20 SY25 SY45 SY55 SY65 SY70 TWDT TBOR TRST TLOCK TOST TDSWU 0.85 3.4 1 — — — — 1.0 4.0 — 5 100 1024 100 1.15 4.6 — — — — — ms ms s s s TOSC s 1.32 prescaler 1:128 prescaler Based on full discharge of 10 F capacitor on VCAP. Includes TPOR and TRST Sleep wake-up with PMSLP = 0 SY71 SY72 Note 1: TPM TLVR — — 1 250 — — s s Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.  2011 Microchip Technology Inc. DS39995B-page 287 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 288  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 30.0 30.1 PACKAGING INFORMATION Package Marking Information 20-Lead PDIP (300 mil) Example PIC24FV32KA301 -I/P e3 1010017 28-Lead SPDIP (.300”) Example PIC24FV32KA302 -I/SP e3 1010017 20-Lead SSOP (5.30 mm) Example PIC24FV32KA 301-I/SS e3 1010017 28-Lead SSOP (5.30 mm) Example PIC24FV32KA 302-I/SS e3 1010017 Legend: XX...X Y YY WW NNN * e3 Product-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( ) e3 can be found on the outer packaging for this package. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  2011 Microchip Technology Inc. DS39995B-page 289 PIC24FV32KA304 FAMILY 20-Lead SOIC (7.50 mm) Example PIC24FV32KA301 -I/SO e3 1010017 28-Lead SOIC (7.50 mm) Example PIC24FV32KA302 -I/SO e3 1010017 28-Lead QFN (6x6 mm) Example PIC24FV32KA 302-I/ML e3 1010017 DS39995B-page 290  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY 44-Lead QFN (8x8x0.9 mm) Example PIC24FV32KA 304-I/ML e3 1010017 44-Lead TQFP (10x10x1 mm) Example PIC24FV32KA 304-I/PT e3 1010017 48-Lead UQFN (6x6x0.5 mm) Example PIC24FV32KA 304-I/MV e3 1010017  2011 Microchip Technology Inc. DS39995B-page 291 PIC24FV32KA304 FAMILY 30.2 Package Details The following sections give the technical details of the packages. /HDG 3ODVWLF 'XDO ,Q /LQH 3 ± 1RWH PLO %RG\ >3',3@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ N NOTE 1 E1 1 2 3 D E A2 L A c A1 b1 b e 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 7RS WR 6HDWLQJ 3ODQH 0ROGHG 3DFNDJH 7KLFNQHVV %DVH WR 6HDWLQJ 3ODQH 6KRXOGHU WR 6KRXOGHU :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK 7LS WR 6HDWLQJ 3ODQH /HDG 7KLFNQHVV 8SSHU /HDG :LGWK /RZHU /HDG :LGWK 2YHUDOO 5RZ 6SDFLQJ † 1 H $ $ $ ( ( ' / F E E H% ± ± ± %6& ± 0,1 ,1&+(6 120 0$; eB ± ± 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD † 6LJQLILFDQW &KDUDFWHULVWLF 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV SHU VLGH 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & % DS39995B-page 292  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY /HDG 6NLQQ\ 3ODVWLF 'XDO ,Q /LQH 63 ± 1RWH PLO %RG\ >63',3@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ N NOTE 1 E1 1 23 D E A A2 L c A1 b1 b e eB 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 7RS WR 6HDWLQJ 3ODQH 0ROGHG 3DFNDJH 7KLFNQHVV %DVH WR 6HDWLQJ 3ODQH 6KRXOGHU WR 6KRXOGHU :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK 7LS WR 6HDWLQJ 3ODQH /HDG 7KLFNQHVV 8SSHU /HDG :LGWK /RZHU /HDG :LGWK 2YHUDOO 5RZ 6SDFLQJ † 1 H $ $ $ ( ( ' / F E E H% ± 0,1 ,1&+(6 120 %6& ± ± ± 0$; ± ± 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD † 6LJQLILFDQW &KDUDFWHULVWLF 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV SHU VLGH 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & %  2011 Microchip Technology Inc. DS39995B-page 293 PIC24FV32KA304 FAMILY /HDG 3ODVWLF 6KULQN 6PDOO 2XWOLQH 66 ± 1RWH PP %RG\ >6623@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ D N E E1 NOTE 1 12 e b c A A2 φ A1 L1 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 0ROGHG 3DFNDJH 7KLFNQHVV 6WDQGRII 2YHUDOO :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK )RRW /HQJWK )RRWSULQW /HDG 7KLFNQHVV )RRW $QJOH /HDG :LGWK 1 H $ $ $ ( ( ' / / F I E ƒ 5() ± ƒ ± ƒ ± ± ± %6& ± 0,1 0,//,0(7(56 120 0$; L 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ PP SHU VLGH 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & % DS39995B-page 294  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011 Microchip Technology Inc. DS39995B-page 295 PIC24FV32KA304 FAMILY /HDG 3ODVWLF 6KULQN 6PDOO 2XWOLQH 66 ± 1RWH PP %RG\ >6623@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ D N E E1 12 NOTE 1 b e c A A2 φ L1 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 0ROGHG 3DFNDJH 7KLFNQHVV 6WDQGRII 2YHUDOO :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK )RRW /HQJWK )RRWSULQW /HDG 7KLFNQHVV )RRW $QJOH /HDG :LGWK 1 H $ $ $ ( ( ' / / F I E ƒ 5() ± ƒ ± ƒ ± ± ± %6& ± 0,1 0,//,0(7(56 120 0$; A1 L 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ PP SHU VLGH 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & % DS39995B-page 296  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011 Microchip Technology Inc. DS39995B-page 297 PIC24FV32KA304 FAMILY /HDG 3ODVWLF 6PDOO 2XWOLQH 62 ± :LGH 1RWH PP %RG\ >62,&@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ D N E E1 NOTE 1 123 b α h A A2 φ c h e L A1 L1 β 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 0ROGHG 3DFNDJH 7KLFNQHVV 6WDQGRII † 2YHUDOO :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK &KDPIHU RSWLRQDO )RRW /HQJWK )RRWSULQW )RRW $QJOH /HDG 7KLFNQHVV /HDG :LGWK 0ROG 'UDIW $QJOH 7RS 0ROG 'UDIW $QJOH %RWWRP 1 H $ $ $ ( ( ' K / / I F E D E ƒ ƒ ƒ ± 0,1 0,//,0(7(56 120 %6& ± ± ± %6& %6& %6& ± ± 5() ± ± ± ± ± ƒ ƒ ± 0$; ƒ 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD † 6LJQLILFDQW &KDUDFWHULVWLF 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ PP SHU VLGH 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & % DS39995B-page 298  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011 Microchip Technology Inc. DS39995B-page 299 PIC24FV32KA304 FAMILY /HDG 3ODVWLF 6PDOO 2XWOLQH 62 ± :LGH 1RWH PP %RG\ >62,&@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ D N E E1 NOTE 1 123 e b h h φ c α A A2 L A1 L1 β 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 0ROGHG 3DFNDJH 7KLFNQHVV 6WDQGRII † 2YHUDOO :LGWK 0ROGHG 3DFNDJH :LGWK 2YHUDOO /HQJWK &KDPIHU RSWLRQDO )RRW /HQJWK )RRWSULQW )RRW $QJOH 7RS /HDG 7KLFNQHVV /HDG :LGWK 0ROG 'UDIW $QJOH 7RS 0ROG 'UDIW $QJOH %RWWRP 1 H $ $ $ ( ( ' K / / I F E D E ƒ ƒ ƒ ± 0,1 0,//,0(7(56 120 %6& ± ± ± %6& %6& %6& ± ± 5() ± ± ± ± ± ƒ ƒ ± 0$; ƒ 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD † 6LJQLILFDQW &KDUDFWHULVWLF 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & PP SHU VLGH % DS39995B-page 300  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011 Microchip Technology Inc. DS39995B-page 301 PIC24FV32KA304 FAMILY /HDG 3ODVWLF 4XDG )ODW 1R /HDG 3DFNDJH 0/ ± [ PP %RG\ >4)1@ ZLWK PP &RQWDFW /HQJWK 1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ D D2 EXPOSED PAD e E E2 2 1 2 1 N NOTE 1 TOP VIEW BOTTOM VIEW L K b N A A3 A1 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 6WDQGRII &RQWDFW 7KLFNQHVV 2YHUDOO :LGWK ([SRVHG 3DG :LGWK 2YHUDOO /HQJWK ([SRVHG 3DG /HQJWK &RQWDFW :LGWK &RQWDFW /HQJWK 1 H $ $ $ ( ( ' ' E / ± %6& 5() %6& %6& 0,1 0,//,0(7(56 120 0$; &RQWDFW WR ([SRVHG 3DG . ± 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 3DFNDJH LV VDZ VLQJXODWHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & % DS39995B-page 302  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY /HDG 3ODVWLF 4XDG )ODW 1R /HDG 3DFNDJH 0/ ± [ PP %RG\ >4)1@ ZLWK PP &RQWDFW /HQJWK 1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ  2011 Microchip Technology Inc. DS39995B-page 303 PIC24FV32KA304 FAMILY /HDG 3ODVWLF 4XDG )ODW 1R /HDG 3DFNDJH 0/ ± [ PP %RG\ >4)1@ 1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ D2 D EXPOSED PAD e E E2 b 2 1 N TOP VIEW NOTE 1 2 1 N L BOTTOM VIEW K A A3 A1 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI 3LQV 3LWFK 2YHUDOO +HLJKW 6WDQGRII &RQWDFW 7KLFNQHVV 2YHUDOO :LGWK ([SRVHG 3DG :LGWK 2YHUDOO /HQJWK ([SRVHG 3DG /HQJWK &RQWDFW :LGWK &RQWDFW /HQJWK 1 H $ $ $ ( ( ' ' E / ± %6& 5() %6& %6& 0,1 0,//,0(7(56 120 0$; &RQWDFW WR ([SRVHG 3DG . ± 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD 3DFNDJH LV VDZ VLQJXODWHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & % DS39995B-page 304  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY /HDG 3ODVWLF 4XDG )ODW 1R /HDG 3DFNDJH 0/ ± [ PP %RG\ >4)1@ 1RWH )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ  2011 Microchip Technology Inc. DS39995B-page 305 PIC24FV32KA304 FAMILY /HDG 3ODVWLF 7KLQ 4XDG )ODWSDFN 37 ± 1RWH [ [ PP %RG\ PP >74)3@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ D D1 E e E1 N b NOTE 1 123 φ NOTE 2 A c α β A1 L L1 A2 8QLWV 'LPHQVLRQ /LPLWV 1XPEHU RI /HDGV /HDG 3LWFK 2YHUDOO +HLJKW 0ROGHG 3DFNDJH 7KLFNQHVV 6WDQGRII )RRW /HQJWK )RRWSULQW )RRW $QJOH 2YHUDOO :LGWK 2YHUDOO /HQJWK 0ROGHG 3DFNDJH :LGWK 0ROGHG 3DFNDJH /HQJWK /HDG 7KLFNQHVV /HDG :LGWK 0ROG 'UDIW $QJOH 7RS 0ROG 'UDIW $QJOH %RWWRP 1 H $ $ $ / / I ( ' ( ' F E D E ƒ ƒ ƒ ± 0,1 0,//,0(7(56 120 %6& ± ± 5() ƒ %6& %6& %6& %6& ± ƒ ƒ ƒ ƒ ƒ 0$; 1RWHV 3LQ YLVXDO LQGH[ IHDWXUH PD\ YDU\ EXW PXVW EH ORFDWHG ZLWKLQ WKH KDWFKHG DUHD &KDPIHUV DW FRUQHUV DUH RSWLRQDO VL]H PD\ YDU\ 'LPHQVLRQV ' DQG ( GR QRW LQFOXGH PROG IODVK RU SURWUXVLRQV 0ROG IODVK RU SURWUXVLRQV VKDOO QRW H[FHHG 'LPHQVLRQLQJ DQG WROHUDQFLQJ SHU $60( < 0 %6& %DVLF 'LPHQVLRQ 7KHRUHWLFDOO\ H[DFW YDOXH VKRZQ ZLWKRXW WROHUDQFHV 5() 5HIHUHQFH 'LPHQVLRQ XVXDOO\ ZLWKRXW WROHUDQFH IRU LQIRUPDWLRQ SXUSRVHV RQO\ PP SHU VLGH 0LFURFKLS 7HFKQRORJ\ 'UDZLQJ & % DS39995B-page 306  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY /HDG 3ODVWLF 7KLQ 4XDG )ODWSDFN 37 ± 1RWH [ [ PP %RG\ PP >74)3@ )RU WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ  2011 Microchip Technology Inc. DS39995B-page 307 PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS39995B-page 308  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011 Microchip Technology Inc. DS39995B-page 309 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 310  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY APPENDIX A: REVISION HISTORY Revision A (March 2011) Original data sheet for the PIC24FV32KA304 family of devices. Revision B (April 2011) Section 25.0 “Charge Time Measurement Unit (CTMU)” was revised to change the description of the IRNG bits in CTMUICON (Register 25-3). Setting ‘01’ is the base current level (0.55 A nominal) and setting ‘00’ is 1000x base current. Section 29.0 “Electrical Characteristics” was revised to change the following typical IPD specifications: • • • • DC20h/i/j/k from 204 A to 200 A DC60h/i/j/k from 0.15 A to 0.025 A DC60l/m/n/o from 0.25 A to 0.040 A DC72h/i/j/k from 0.80 A to 0.70 A  2011 Microchip Technology Inc. DS39995B-page 311 PIC24FV32KA304 FAMILY NOTES: DS39995B-page 312  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY INDEX A A/D Control Registers ..................................................... 214 AD1CHITH/L .................................................... 214 AD1CHS .......................................................... 214 AD1CON1 ........................................................ 214 AD1CON2 ........................................................ 214 AD1CON3 ........................................................ 214 AD1CON5 ........................................................ 214 AD1CSSL/H ..................................................... 214 AD1CTMENH/L ............................................... 214 Conversion Timing Requirements .................... 286, 288 Module Specifications .............................................. 285 Result Buffers .......................................................... 214 Sampling Requirements ........................................... 223 Transfer Function ..................................................... 224 AC Characteristics Capacitive Loading Requirements on Output Pins ...................................................... 280 Comparator .............................................................. 284 Comparator Voltage Reference Settling Time ......... 284 Internal RC Accuracy ............................................... 282 Internal RC Oscillator Specifications ........................ 282 Load Conditions and Requirements ......................... 280 Temperature and Voltage Specifications ................. 280 Assembler MPASM Assembler .................................................. 252 Output Compare (Double-Buffered, 16-Bit PWM Mode) .......................................... 158 PIC24F CPU Core ..................................................... 32 PIC24FV32KA304 Family (General) ......................... 17 PSV Operation ........................................................... 57 Reset System ............................................................ 73 RTCC ....................................................................... 189 Serial Resistor ......................................................... 133 Shared I/O Port Structure ........................................ 139 Simplified UART ...................................................... 181 SPIx Module (Enhanced Buffer Mode) .................... 167 SPIx Module (Standard Buffer Mode) ...................... 166 System Clock ........................................................... 117 Table Register Addressing ........................................ 59 Timer2/3, Timer4/5 (32-Bit) ..................................... 146 Watchdog Timer (WDT) ........................................... 249 Brown-out Reset Trip Points ............................................................... 266 C C Compilers MPLAB C18 ............................................................. 252 Charge Time Measurement Unit. See CTMU. Code Examples Data EEPROM Bulk Erase ........................................ 71 Data EEPROM Unlock Sequence ............................. 67 Erasing a Program Memory Row, ‘C’ Language Code ............................................ 63 Erasing a Program Memory Row, Assembly Language Code ................................................. 62 I/O Port Write/Read ................................................. 142 Initiating a Programming Sequence, ‘C’ Language Code ............................................ 64 Initiating a Programming Sequence, Assembly Language Code ................................ 64 Loading the Write Buffers, ‘C’ Language Code ......... 64 Loading the Write Buffers, Assembly Language Code ................................................. 63 Programming a Single Word of Flash Program Memory ............................................... 65 PWRSAV Instruction Syntax ................................... 127 Reading the Data EEPROM Using the TBLRD Command ............................................. 72 Sequence for Clock Switching ................................. 124 Setting the RTCWREN Bit ....................................... 190 Single-Word Erase .................................................... 70 Single-Word Write to Data EEPROM ........................ 71 Ultra Low-Power Wake-up Initialization ................... 133 Unlock Sequence .................................................... 128 Code Protection ............................................................... 250 Comparator ...................................................................... 225 Comparator Voltage Reference ....................................... 229 Configuring .............................................................. 229 Configuration Bits ............................................................ 239 Core Features .................................................................... 13 CPU ALU ............................................................................ 35 Control Registers ....................................................... 34 Core Registers ........................................................... 32 Programmer’s Model ................................................. 31 B Baud Rate Generator Setting as a Bus Master ........................................... 175 Block Diagrams 12-Bit A/D Converter ................................................ 212 12-Bit A/D Converter Analog Input Model ................ 223 16-Bit Asynchronous Timer3 and Timer5 ................ 147 16-Bit Synchronous Timer2 and Timer4 .................. 147 16-Bit Timer1 ........................................................... 143 Accessing Program Memory with Table Instructions ........................................................ 56 CALL Stack Frame ..................................................... 53 Comparator Module ................................................. 225 Comparator Voltage Reference ............................... 229 CPU Programmer’s Model ......................................... 33 CRC Module ............................................................ 203 CRC Shift Engine ..................................................... 203 CTMU Connections and Internal Configuration for Capacitance Measurement ......................... 232 CTMU Typical Connections and Internal Configuration for Pulse Delay Generation ....... 233 CTMU Typical Connections and Internal Configuration for Time Measurement .............. 233 Data Access From Program Space Address Generation ......................................................... 54 Data EEPROM Addressing with TBLPAG and NVM Registers ................................................... 69 High/Low-Voltage Detect (HLVD) ............................ 209 I2C Module ............................................................... 174 Individual Comparator Configurations ...................... 226 Input Capture ........................................................... 151 On-Chip Regulator Connections .............................. 248 Output Compare (16-Bit Mode) ................................ 156  2011 Microchip Technology Inc. DS39995B-page 313 PIC24FV32KA304 FAMILY CRC Registers .................................................................. 205 Typical Operation ..................................................... 205 User Interface .......................................................... 204 Data ................................................................. 204 Data Shift Direction .......................................... 205 Interrupt Operation ........................................... 205 Polynomial ....................................................... 204 CTMU Measuring Capacitance ........................................... 231 Measuring Time ....................................................... 233 Pulse Generation and Delay .................................... 233 Customer Change Notification Service ............................ 317 Customer Notification Service .......................................... 317 Customer Support ............................................................ 317 Errata ................................................................................. 11 Examples Baud Rate Error Calculation (BRGH = 0) ................ 182 F Flash Program Memory Control Registers ....................................................... 60 Enhanced ICSP Operation ........................................ 60 Programming Algorithm ............................................. 62 Programming Operations ........................................... 60 RTSP Operation ........................................................ 60 Table Instructions ...................................................... 59 H High/Low-Voltage Detect (HLVD) .................................... 209 D Data EEPROM Memory ..................................................... 67 Erasing ....................................................................... 70 Operations ................................................................. 69 Programming Bulk Erase .......................................................... 71 Reading Data EEPROM .................................... 72 Single-Word Write .............................................. 71 Programming Control Registers NVMADR(U) ...................................................... 69 NVMCON ........................................................... 67 NVMKEY ............................................................ 67 Data Memory Address Space ........................................................... 39 Memory Map .............................................................. 39 Near Data Space ....................................................... 40 Organization ............................................................... 40 SFR Space ................................................................. 40 Software Stack ........................................................... 53 Space Width ............................................................... 39 DC Characteristics Comparator .............................................................. 278 Comparator Voltage Reference ............................... 278 CTMU Current Source ............................................. 279 Data EEPROM Memory ........................................... 278 High/Low-Voltage Detect ......................................... 266 I/O Pin Input Specifications ...................................... 276 I/O Pin Output Specifications ................................... 277 Idle Current (IIDLE) ................................................... 269 Internal Voltage Regulator Specifications ................ 279 Operating Current (IDD) ............................................ 267 Power-Down Current (IPD) ....................................... 271 Program Memory ..................................................... 277 Temperature and Voltage Specifications ................. 265 Development Support ...................................................... 251 Device Features (Summary) ........................................ 15, 16 I I/O Ports Analog Port Configuration ........................................ 140 Analog Selection Registers ...................................... 140 Input Change Notification ........................................ 142 Open-Drain Configuration ........................................ 140 Parallel (PIO) ........................................................... 139 I2C Clock Rates ............................................................. 175 Communicating as Master in Single Master Environment .................................................... 173 Pin Remapping Options ........................................... 173 Reserved Addresses ............................................... 175 Slave Address Masking ........................................... 175 In-Circuit Debugger .......................................................... 250 In-Circuit Serial Programming (ICSP) .............................. 250 Input Capture 32-Bit Mode ............................................................. 152 Operations ............................................................... 152 Synchronous and Trigger Modes ............................. 151 Input Capture with Dedicated Timers .............................. 151 Instruction Set Opcode Symbols ..................................................... 256 Overview .................................................................. 257 Summary ................................................................. 255 Internet Address .............................................................. 317 Interrupts Alternate Interrupt Vector Table (AIVT) ..................... 79 Control and Status Registers ..................................... 82 Implemented Vectors ................................................. 81 Interrupt Vector Table (IVT) ....................................... 79 Reset Sequence ........................................................ 79 Setup Procedures .................................................... 115 Trap Vectors .............................................................. 81 Vector Table .............................................................. 80 M Microchip Internet Web Site ............................................. 317 MPLAB ASM30 Assembler, Linker, Librarian .................. 252 MPLAB Integrated Development Environment Software .................................................................. 251 MPLAB PM3 Device Programmer ................................... 254 MPLAB REAL ICE In-Circuit Emulator System ............... 253 MPLINK Object Linker/MPLIB Object Librarian ............... 252 E Electrical Characteristics Absolute Maximum Ratings ..................................... 263 Thermal Operating Conditions ................................. 265 Thermal Packaging Characteristics ......................... 265 V/F Graphs ............................................................... 264 Equations Baud Rate Reload Calculation ................................. 175 Calculating the PWM Period .................................... 159 Calculation for Maximum PWM Resolution .............. 159 Device and SPI Clock Speed Relationship .............. 172 PWM Period and Duty Cycle Calculations ............... 159 UART Baud Rate with BRGH = 0 ............................ 182 UART Baud Rate with BRGH = 1 ............................ 182 DS39995B-page 314 N Near Data Space ............................................................... 40  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY O On-Chip Voltage Regulator .............................................. 248 Oscillator Configuration Clock Switching ........................................................ 123 Sequence ......................................................... 123 Configuration Values for Clock Selection ................. 118 CPU Clocking Scheme ............................................ 118 Initial Configuration on POR .................................... 118 Reference Clock Output ........................................... 124 Output Compare 32-Bit Mode .............................................................. 155 Operations ............................................................... 157 Subcycle Resolution ................................................ 160 Synchronous and Trigger Modes ............................. 155 I2C ............................................................................. 46 ICN ............................................................................ 42 Input Capture ............................................................. 44 Interrupt Controller ..................................................... 43 NVM ........................................................................... 52 Output Compare ........................................................ 45 Pad Configuration ...................................................... 48 PMD ........................................................................... 52 PORTA ...................................................................... 47 PORTB ...................................................................... 47 PORTC ...................................................................... 48 Real-Time Clock and Calendar (RTCC) .................... 50 SPI ............................................................................. 47 Timer ......................................................................... 44 UART ......................................................................... 46 Ultra Low-Power Wake-up ......................................... 52 Registers AD1CHITH (A/D Scan Compare Hit, High Word) ...................................................... 220 AD1CHITH (A/D Scan Compare Hit, Low Word) ..... 220 AD1CHS (A/D Sample Select) ................................ 219 AD1CON1 (A/D Control 1) ....................................... 215 AD1CON2 (A/D Control 2) ....................................... 216 AD1CON3 (A/D Control 3) ....................................... 217 AD1CON5 (A/D Control 5) ....................................... 218 AD1CTMENH (CTMU Enable, High Word) ............. 222 AD1CTMENL (CTMU Enable, Low Word) ............... 222 ADCSSH (A/D Input Scan Select, High Word) ........ 221 ADCSSL (A/D Input Scan Select, Low Word) ......... 221 ALCFGRPT (Alarm Configuration) .......................... 194 ALMINSEC (Alarm Minutes and Seconds Value) .............................................................. 198 ALMTHDY (Alarm Month and Day Value) ............... 197 ALWDHR (Alarm Weekday and Hours Value) ........ 197 ANSA (Analog Selection, PORTA) .......................... 140 ANSB (Analog Selection, PORTB) .......................... 141 ANSC (Analog Selection, PORTC) .......................... 141 CLKDIV (Clock Divider) ........................................... 121 CMSTAT (Comparator Status) ................................ 228 CMxCON (Comparator x Control) ........................... 227 CORCON (CPU Control) ........................................... 35 CORCON (CPU Core Control) .................................. 84 CRCCON1 (CRC Control 1) .................................... 206 CRCCON2 (CRC Control 2) .................................... 207 CRCXORH (CRC XOR Polynomial, High Byte) ...... 208 CRCXORL (CRC XOR Polynomial, Low Byte) ........ 207 CTMUCON (CTMU Control 1) ................................. 234 CTMUCON2 (CTMU Control 2) ............................... 235 CTMUICON (CTMU Current Control) ...................... 237 CVRCON (Comparator Voltage Reference Control) .......................................... 230 DEVID (Device ID) ................................................... 246 DEVREV (Device Revision) ..................................... 247 DSCON (Deep Sleep Control) ................................. 131 DSWAKE (Deep Sleep Wake-up Source) ............... 132 FBS (Boot Segment Configuration) ......................... 239 FDS (Deep Sleep Configuration) ............................. 245 FGS (General Segment Configuration) ................... 240 FICD (In-Circuit Debugger Configuration) ............... 244 FOSC (Oscillator Configuration) .............................. 241 FOSCSEL (Oscillator Selection Configuration) ....... 240 FPOR (Reset Configuration) ................................... 243 FWDT (Watchdog Timer Configuration) .................. 242 HLVDCON (High/Low-Voltage Detect Control) ....... 210 I2CxMSK (I2Cx Slave Mode Address Mask) ........... 180 P Packaging Details ...................................................................... 292 Marking .................................................................... 289 Pinout Descriptions ............................................................ 18 Power-Saving ................................................................... 137 Power-Saving Features ................................................... 127 Clock Frequency, Clock Switching ........................... 127 Coincident Interrupts ................................................ 128 Instruction-Based Modes ......................................... 127 Deep Sleep ...................................................... 128 Idle ................................................................... 128 Sleep ................................................................ 127 Selective Peripheral Control .................................... 137 Ultra Low-Power Wake-up ....................................... 133 Voltage Regulator-Based ......................................... 135 Deep Sleep Mode ............................................ 135 Fast Wake-up Sleep Mode .............................. 135 Retention Sleep Mode ..................................... 135 Run Mode ........................................................ 135 Sleep (Standby) Mode ..................................... 135 Product Identification System .......................................... 319 Program and Data Memory Access Using Table Instructions ................................ 55 Program Space Visibility ............................................ 57 Program and Data Memory Spaces Addressing ................................................................. 53 Interfacing .................................................................. 53 Program Memory Address Space ........................................................... 37 Device Configuration Words ...................................... 38 Hard Memory Vectors ................................................ 38 Memory Map .............................................................. 37 Organization ............................................................... 38 Program Verification ........................................................ 250 Pulse-Width Modulation (PWM) Mode ............................. 158 Pulse-Width Modulation. See PWM. PWM Duty Cycle and Period ............................................. 159 R Reader Response ............................................................ 318 Register Maps A/D Converter (ADC) ................................................. 49 Analog Select ............................................................. 50 Clock Control ............................................................. 51 CPU Core ................................................................... 41 CRC ........................................................................... 51 CTMU ......................................................................... 50 Deep Sleep ................................................................ 51  2011 Microchip Technology Inc. DS39995B-page 315 PIC24FV32KA304 FAMILY I2CxSTAT (I2Cx Status) .......................................... 178 I2CxxCON (I2Cx Control) ........................................ 176 ICxCON1 (Input Capture x Control 1) ...................... 153 ICxCON2 (Input Capture x Control 2) ...................... 154 IEC0 (Interrupt Enable Control 0) .............................. 93 IEC1 (Interrupt Enable Control 1) .............................. 94 IEC2 (Interrupt Enable Control 2) .............................. 95 IEC3 (Interrupt Enable Control 3) .............................. 96 IEC4 (Interrupt Enable Control 4) .............................. 97 IEC5 (Interrupt Enable Control 5) .............................. 98 IFS0 (Interrupt Flag Status 0) .................................... 87 IFS1 (Interrupt Flag Status 1) .................................... 88 IFS2 (Interrupt Flag Status 2) .................................... 89 IFS3 (Interrupt Flag Status 3) .................................... 90 IFS4 (Interrupt Flag Status 4) .................................... 91 IFS5 (Interrupt Flag Status 5) .................................... 92 INTCON1 (Interrupt Control 1) ................................... 85 INTTREG (Interrupt Control and Status) .................. 114 IPC0 (Interrupt Priority Control 0) .............................. 99 IPC1 (Interrupt Priority Control 1) ............................ 100 IPC12 (Interrupt Priority Control 12) ........................ 109 IPC120 (Interrupt Priority Control 20) ...................... 113 IPC15 (Interrupt Priority Control 15) ........................ 110 IPC16 (Interrupt Priority Control 16) ........................ 111 IPC18 (Interrupt Priority Control 18) ........................ 112 IPC2 (Interrupt Priority Control 2) ............................ 101 IPC3 (Interrupt Priority Control 3) ............................ 102 IPC4 (Interrupt Priority Control 4) ............................ 103 IPC5 (Interrupt Priority Control 5) ............................ 104 IPC6 (Interrupt Priority Control 6) ............................ 105 IPC7 (Interrupt Priority Control 7) ............................ 106 IPC8 (Interrupt Priority Control 8) ............................ 107 IPC9 (Interrupt Priority Control 9) ............................ 108 MINSEC (RTCC Minutes and Seconds Value) ........ 196 MTHDY (RTCC Month and Day Value) ................... 195 NVMCON (Flash Memory Control) ............................ 61 NVMCON (Nonvolatile Memory Control) ................... 68 OCxCON1 (Output Compare x Control 1) ............... 161 OCxCON2 (Output Compare x Control 2) ............... 163 OSCCON (Oscillator Control) .................................. 119 OSCTUN (FRC Oscillator Tune) .............................. 122 PADCFG1 (Pad Configuration Control) ................... 180 RCFGCAL (RTCC Calibration and Configuration) .................................................. 191 RCON (Reset Control) ............................................... 74 REFOCON (Reference Oscillator Control) ............... 125 RTCCSWT (Control/Sample Window Timer) ........... 199 RTCPWC (RTCC Configuration 2) .......................... 193 SPIxCON1 (SPIx Control 1) ..................................... 170 SPIxCON2 (SPIx Control 2) ..................................... 171 SPIxSTAT (SPIx Status and Control) ...................... 168 SR (ALU STATUS) .............................................. 34, 83 T1CON (Timer1 Control) .......................................... 144 TxCON (Timer2/4 Control) ....................................... 148 TyCON (Timer3/5 Control) ....................................... 149 ULPWCON (ULPWU Control) .................................. 134 UxMODE (UARTx Mode) ......................................... 184 UxRXREG (UARTx Receive) ................................... 188 UxSTA (UARTx Status and Control) ........................ 186 UxTXREG (UARTx Transmit) .................................. 188 WKDYHR (RTCC Weekday and Hours Value) ........ 196 YEAR (RTCC Year Value) ....................................... 195 Resets Brown-out Reset (BOR) ............................................. 77 Clock Source Selection .............................................. 75 Deep Sleep BOR (DSBOR) ....................................... 77 Delay Times ............................................................... 76 Device Times ............................................................. 76 RCON Flag Operation ............................................... 75 SFR States ................................................................ 77 Revision History ............................................................... 311 RTCC ............................................................................... 189 Alarm Configuration ................................................. 200 Alarm Mask Settings (figure) ................................... 201 Calibration ............................................................... 200 Module Registers ..................................................... 190 Mapping ........................................................... 190 Clock Source Selection ........................... 190 Write Lock ........................................................ 190 Source Clock ........................................................... 189 S Serial Peripheral Interface. See SPI. SFR Space ........................................................................ 40 Software Simulator (MPLAB SIM) ................................... 253 Software Stack ................................................................... 53 T Timer1 .............................................................................. 143 Timer2/3 ........................................................................... 145 Timer2/3 and Timer4/5 .................................................... 145 Timing Diagrams CLKO and I/O Timing .............................................. 283 External Clock .......................................................... 281 Timing Requirements CLKO and I/O .......................................................... 283 External Clock .......................................................... 281 PLL Clock Specifications ......................................... 282 U UART ............................................................................... 181 Baud Rate Generator (BRG) ................................... 182 Break and Sync Transmit Sequence ....................... 183 IrDA Support ............................................................ 183 Operation of UxCTS and UxRTS Control Pins ........ 183 Receiving in 8-Bit or 9-Bit Data Mode ...................... 183 Transmitting in 8-Bit Data Mode .............................. 183 Transmitting in 9-Bit Data Mode .............................. 183 W Watchdog Timer Deep Sleep (DSWDT) ............................................. 250 Watchdog Timer (WDT) ................................................... 248 Windowed Operation ............................................... 249 WWW Address ................................................................ 317 WWW, On-Line Support .................................................... 11 DS39995B-page 316  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY THE MICROCHIP WEB SITE Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: • Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software • General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • • • • • Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://microchip.com/support CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under “Support”, click on “Customer Change Notification” and follow the registration instructions.  2011 Microchip Technology Inc. DS39995B-page 317 PIC24FV32KA304 FAMILY READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. TO: RE: Technical Publications Manager Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y N Literature Number: DS39995B FAX: (______) _________ - _________ Device: PIC24FV32KA304 Family Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS39995B-page 318  2011 Microchip Technology Inc. PIC24FV32KA304 FAMILY PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PIC 24 FV 32 KA3 04 T - I / PT - XXX Microchip Trademark Architecture Flash Memory Family Program Memory Size (KB) Product Group Pin Count Tape and Reel Flag (if applicable) Temperature Range Package Pattern b) Examples: a) PIC24FV32KA304-I/ML: Wide voltage range, General Purpose, 32 -Kbyte program memory, 44-pin, Industrial temp, QFN package PIC24F16KA302-I/SS: Standard voltage range, General Purpose, 16-Kbyte program memory, 28-pin, Industrial temp, SSOP package Architecture Flash Memory Family 24 F FV = 16-bit modified Harvard without DSP = Standard voltage range Flash program memory = Wide voltage range Flash program memory Product Group Pin Count KA3 = General purpose microcontrollers 01 02 04 I SP SO SS ML P PT = 20-pin = 28-pin = 44-pin = -40C to +85C (Industrial) = = = = = = SPDIP SOIC SSOP QFN PDIP TQFP Temperature Range Package Pattern Three-digit QTP, SQTP, Code or Special Requirements (blank otherwise) ES = Engineering Sample  2011 Microchip Technology Inc. DS39995B-page 319 Worldwide Sales and Service AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 ASIA/PACIFIC India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-213-7830 Fax: 886-7-330-9305 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 02/18/11 DS39995B-page 320  2011 Microchip Technology Inc.