SST39VF400A

2 Mbit / 4 Mbit / 8 Mbit (x16) Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet The SST39LF200A/400A/800A and SST39VF200A/400A/800A devices are 128K x16 / 256K x16 / 512K x16 CMOS Multi-Purpose Flash (MPF) manufactured with SST proprietary, high-performance CMOS SuperFlash technology. The split-gate cell design and thick oxide tunneling injector attain better reliability and manufacturability compared with alternate approaches. The SST39LF200A/400A/800A write (Program or Erase) with a 3.0-3.6V power supply. The SST39VF200A/400A/ 800A write (Program or Erase) with a 2.7-3.6V power supply. These devices conform to JEDEC standard pinouts for x16 memories. Features: • Organized as 128K x16 / 256K x16 / 512K x16 • Single Voltage Read and Write Operations – 3.0-3.6V for SST39LF200A/400A/800A – 2.7-3.6V for SST39VF200A/400A/800A • Fast Erase and Word-Program – Sector-Erase Time: 18 ms (typical) – Block-Erase Time: 18 ms (typical) – Chip-Erase Time: 70 ms (typical) – Word-Program Time: 14 µs (typical) – Chip Rewrite Time: 2 seconds (typical) for SST39LF/VF200A 4 seconds (typical) for SST39LF/VF400A 8 seconds (typical) for SST39LF/VF800A • Superior Reliability – Endurance: 100,000 Cycles (typical) – Greater than 100 years Data Retention • Low Power Consumption (typical values at 14 MHz) – Active Current: 9 mA (typical) – Standby Current: 3 µA (typical) • Automatic Write Timing – Internal VPP Generation • End-of-Write Detection – Toggle Bit – Data# Polling • Sector-Erase Capability – Uniform 2 KWord sectors • CMOS I/O Compatibility • JEDEC Standard – Flash EEPROM Pinouts and command sets • Block-Erase Capability – Uniform 32 KWord blocks • Fast Read Access Time – 55 ns for SST39LF200A/400A/800A – 70 ns for SST39VF200A/400A/800A • Packages Available – 48-lead TSOP (12mm x 20mm) – 48-ball TFBGA (6mm x 8mm) – 48-ball WFBGA (4mm x 6mm) – 48-bump XFLGA (4mm x 6mm) – 4 and 8Mbit • Latched Address and Data • All non-Pb (lead-free) devices are RoHS compliant ©2011 Silicon Storage Technology, Inc. www.microchip.com DS25001A 03/11 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Product Description The SST39LF200A/400A/800A and SST39VF200A/400A/800A devices are 128K x16 / 256K x16 / 512K x16 CMOS Multi-Purpose Flash (MPF) manufactured with SST proprietary, high-performance CMOS SuperFlash technology. The split-gate cell design and thick oxide tunneling injector attain better reliability and manufacturability compared with alternate approaches. The SST39LF200A/400A/800A write (Program or Erase) with a 3.0-3.6V power supply. The SST39VF200A/400A/800A write (Program or Erase) with a 2.7-3.6V power supply. These devices conform to JEDEC standard pinouts for x16 memories. Featuring high-performance Word-Program, the SST39LF200A/400A/800A and SST39VF200A/400A/ 800A devices provide a typical Word-Program time of 14 µsec. The devices use Toggle Bit or Data# Polling to detect the completion of the Program or Erase operation. To protect against inadvertent write, they have on-chip hardware and software data protection schemes. Designed, manufactured, and tested for a wide spectrum of applications, these devices are offered with a guaranteed typical endurance of 100,000 cycles. Data retention is rated at greater than 100 years. The SST39LF200A/400A/800A and SST39VF200A/400A/800A devices are suited for applications that require convenient and economical updating of program, configuration, or data memory. For all system applications, they significantly improve performance and reliability, while lowering power consumption. They inherently use less energy during Erase and Program than alternative flash technologies. When programming a flash device, the total energy consumed is a function of the applied voltage, current, and time of application. Since for any given voltage range, the SuperFlash technology uses less current to program and has a shorter erase time, the total energy consumed during any Erase or Program operation is less than alternative flash technologies. These devices also improve flexibility while lowering the cost for program, data, and configuration storage applications. The SuperFlash technology provides fixed Erase and Program times, independent of the number of Erase/Program cycles that have occurred. Therefore the system software or hardware does not have to be modified or de-rated as is necessary with alternative flash technologies, whose Erase and Program times increase with accumulated Erase/Program cycles. To meet surface mount requirements, the SST39LF200A/400A/800A and SST39VF200A/400A/800A are offered in 48-lead TSOP packages and 48-ball TFBGA packages as well as Micro-Packages. See Figures 2, 3, and 4 for pin assignments. © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 2 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Block Diagram X-Decoder SuperFlash Memory Memory Address Address Buffer Latches Y-Decoder CE# OE# WE# DQ15 - DQ0 1117 B1.2 Control Logic I/O Buffers and Data Latches Figure 1: Functional Block Diagram Pin Assignments 800A A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE# NC NC NC NC A18 A17 A7 A6 A5 A4 A3 A2 A1 400A A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE# NC NC NC NC NC A17 A7 A6 A5 A4 A3 A2 A1 SST39LF/VF200A A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE# NC NC NC NC NC NC A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 SST39LF/VF200A 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VDD DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 400A A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VDD DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 800A A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VDD DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 Standard Pinout Top View Die Up 1117 48-tsop P01.3 Figure 2: Pin Assignments for 48-Lead TSOP © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 3 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TOP VIEW (balls facing down) SST39LF/VF200A 6 5 4 3 2 1 A13 A12 A14 A9 A8 A10 NC NC A6 A2 A15 A16 NC DQ15 VSS A11 DQ7 DQ14 DQ13 DQ6 NC DQ5 DQ12 VDD DQ4 1117 48-tfbga P02 2.0 WE# NC NC A7 A3 NC NC A4 NC DQ2 DQ10 DQ11 DQ3 A5 A1 DQ0 DQ8 DQ9 DQ1 A0 CE# OE# VSS A TOP VIEW (balls facing down) B C D E F G H TOP VIEW (balls facing down) SST39LF/VF400A SST39LF/VF800A 6 5 4 3 2 1 A13 A12 A14 A9 A8 A10 NC NC A6 A2 A15 A16 NC DQ15 VSS A11 DQ7 DQ14 DQ13 DQ6 NC DQ5 DQ12 VDD DQ4 1117 48-tfbga P02 4.0 6 5 4 3 2 1 A13 A12 A14 A9 A8 A10 NC A18 A6 A2 A15 A16 NC DQ15 VSS A11 DQ7 DQ14 DQ13 DQ6 NC DQ5 DQ12 VDD DQ4 1117 48-tfbga P02 8.0 WE# NC NC A7 A3 NC A17 A4 WE# NC NC A7 A3 NC A17 A4 NC DQ2 DQ10 DQ11 DQ3 A5 A1 DQ0 DQ8 DQ9 DQ1 A0 CE# OE# VSS NC DQ2 DQ10 DQ11 DQ3 A5 A1 DQ0 DQ8 DQ9 DQ1 A0 CE# OE# VSS A B C D E F G H A B C D E F G H Figure 3: Pin Assignments for 48-Ball TFBGA © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 4 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TOP VIEW (balls facing down) SST39VF200A 6 A2 A4 A3 A5 A6 A7 NC NC NC NC NC WE# NC NC A9 A10 A8 A11 A13 A12 A14 A15 5 A1 4 A0 3 CE# DQ8 DQ10 OE# DQ9 NC NC DQ4 DQ11 A16 DQ5 DQ6 DQ7 1117 48-xflga P03 2.0 2 VSS 1 DQ0 DQ1 DQ2 DQ3 VDD DQ12 DQ13 DQ14 DQ15 VSS A B C D E F G H J K L TOP VIEW (balls facing down) SST39LF/VF400A 6 A2 A4 A3 A5 A6 A7 NC A17 NC NC NC WE# NC NC A9 A10 A8 A11 A13 A12 A14 A15 5 A1 4 A0 3 CE# DQ8 DQ10 OE# DQ9 NC NC DQ4 DQ11 A16 DQ5 DQ6 DQ7 1117 48-xflga P03 4.0 1117 48-xflga P03 8.0 2 VSS 1 DQ0 DQ1 DQ2 DQ3 VDD DQ12 DQ13 DQ14 DQ15 VSS A B C D E F G H J K L TOP VIEW (balls facing down) SST39LF/VF800A 6 A2 A4 A3 A5 A6 A7 A18 A17 NC NC NC WE# NC NC A9 A10 A8 A11 A13 A12 A14 A15 5 A1 4 A0 3 CE# DQ8 DQ10 OE# DQ9 NC NC DQ4 DQ11 A16 DQ5 DQ6 DQ7 2 VSS 1 DQ0 DQ1 DQ2 DQ3 VDD DQ12 DQ13 DQ14 DQ15 VSS A B C D E F G H J K L Figure 4: Pin Assignments for 48-Ball WFBGA and 48-Bump XFLGA © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 5 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Table 1: Pin Description Symbol AMS1-A0 Pin Name Address Inputs Functions To provide memory addresses. During Sector-Erase AMS-A11 address lines will select the sector. During Block-Erase AMS-A15 address lines will select the block. DQ15-DQ0 Data Input/output To output data during Read cycles and receive input data during Write cycles. Data is internally latched during a Write cycle. The outputs are in tri-state when OE# or CE# is high. Chip Enable Output Enable Write Enable Power Supply Ground No Connection Unconnected pins. T1.2 25001 CE# OE# WE# VDD VSS NC To activate the device when CE# is low. To gate the data output buffers. To control the Write operations. To provide power supply voltage: 3.0-3.6V for SST39LF200A/400A/800A 2.7-3.6V for SST39VF200A/400A/800A 1. AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A, and A18 for SST39LF/VF800A © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 6 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Device Operation Commands are used to initiate the memory operation functions of the device. Commands are written to the device using standard microprocessor write sequences. A command is written by asserting WE# low while keeping CE# low. The address bus is latched on the falling edge of WE# or CE#, whichever occurs last. The data bus is latched on the rising edge of WE# or CE#, whichever occurs first. Read The Read operation of the SST39LF200A/400A/800A and SST39VF200A/400A/800A is controlled by CE# and OE#, both have to be low for the system to obtain data from the outputs. CE# is used for device selection. When CE# is high, the chip is deselected and only standby power is consumed. OE# is the output control and is used to gate data from the output pins. The data bus is in high impedance state when either CE# or OE# is high. Refer to the Read cycle timing diagram for further details (Figure 5). Word-Program Operation The SST39LF200A/400A/800A and SST39VF200A/400A/800A are programmed on a word-by-word basis. Before programming, the sector where the word exists must be fully erased. The Program operation is accomplished in three steps. The first step is the three-byte load sequence for Software Data Protection. The second step is to load word address and word data. During the Word-Program operation, the addresses are latched on the falling edge of either CE# or WE#, whichever occurs last. The data is latched on the rising edge of either CE# or WE#, whichever occurs first. The third step is the internal Program operation which is initiated after the rising edge of the fourth WE# or CE#, whichever occurs first. The Program operation, once initiated, will be completed within 20 µs. See Figures 6 and 7 for WE# and CE# controlled Program operation timing diagrams and Figure 18 for flowcharts. During the Program operation, the only valid reads are Data# Polling and Toggle Bit. During the internal Program operation, the host is free to perform additional tasks. Any commands issued during the internal Program operation are ignored. Sector/Block-Erase Operation The Sector- (or Block-) Erase operation allows the system to erase the device on a sector-by-sector (or block-by-block) basis. The SST39LF200A/400A/800A and SST39VF200A/400A/800A offers both Sector-Erase and Block-Erase mode. The sector architecture is based on uniform sector size of 2 KWord. The Block-Erase mode is based on uniform block size of 32 KWord. The Sector-Erase operation is initiated by executing a six-byte command sequence with Sector-Erase command (30H) and sector address (SA) in the last bus cycle. The Block-Erase operation is initiated by executing a six-byte command sequence with Block-Erase command (50H) and block address (BA) in the last bus cycle. The sector or block address is latched on the falling edge of the sixth WE# pulse, while the command (30H or 50H) is latched on the rising edge of the sixth WE# pulse. The internal Erase operation begins after the sixth WE# pulse. The End-of-Erase operation can be determined using either Data# Polling or Toggle Bit methods. See Figures 11 and 12 for timing waveforms. Any commands issued during the Sector- or Block-Erase operation are ignored. Chip-Erase Operation The SST39LF200A/400A/800A and SST39VF200A/400A/800A provide a Chip-Erase operation, which allows the user to erase the entire memory array to the “1” state. This is useful when the entire device must be quickly erased. © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 7 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet The Chip-Erase operation is initiated by executing a six-byte command sequence with Chip-Erase command (10H) at address 5555H in the last byte sequence. The Erase operation begins with the rising edge of the sixth WE# or CE#, whichever occurs first. During the Erase operation, the only valid read is Toggle Bit or Data# Polling. See Table 4 for the command sequence, Figure 10 for timing diagram, and Figure 21 for the flowchart. Any commands issued during the Chip-Erase operation are ignored. Write Operation Status Detection The SST39LF200A/400A/800A and SST39VF200A/400A/800A provide two software means to detect the completion of a write (Program or Erase) cycle, in order to optimize the system write cycle time. The software detection includes two status bits: Data# Polling (DQ7) and Toggle Bit (DQ6). The End-ofWrite detection mode is enabled after the rising edge of WE#, which initiates the internal Program or Erase operation. The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a Data# Polling or Toggle Bit read may be simultaneous with the completion of the write cycle. If this occurs, the system may possibly get an erroneous result, i.e., valid data may appear to conflict with either DQ7 or DQ6. In order to prevent spurious rejection, if an erroneous result occurs, the software routine should include a loop to read the accessed location an additional two (2) times. If both reads are valid, then the device has completed the write cycle, otherwise the rejection is valid. Data# Polling (DQ7) When the SST39LF200A/400A/800A and SST39VF200A/400A/800A are in the internal Program operation, any attempt to read DQ7 will produce the complement of the true data. Once the Program operation is completed, DQ7 will produce true data. Note that even though DQ7 may have valid data immediately following the completion of an internal Write operation, the remaining data outputs may still be invalid: valid data on the entire data bus will appear in subsequent successive Read cycles after an interval of 1 µs. During internal Erase operation, any attempt to read DQ7 will produce a ‘0’. Once the internal Erase operation is completed, DQ7 will produce a ‘1’. The Data# Polling is valid after the rising edge of fourth WE# (or CE#) pulse for Program operation. For Sector-, Block- or Chip-Erase, the Data# Polling is valid after the rising edge of sixth WE# (or CE#) pulse. See Figure 8 for Data# Polling timing diagram and Figure 19 for a flowchart. Toggle Bit (DQ6) During the internal Program or Erase operation, any consecutive attempts to read DQ6 will produce alternating 1s and 0s, i.e., toggling between 1 and 0. When the internal Program or Erase operation is completed, the DQ6 bit will stop toggling. The device is then ready for the next operation. The Toggle Bit is valid after the rising edge of fourth WE# (or CE#) pulse for Program operation. For Sector-, Blockor Chip-Erase, the Toggle Bit is valid after the rising edge of sixth WE# (or CE#) pulse. See Figure 9 for Toggle Bit timing diagram and Figure 19 for a flowchart. Data Protection The SST39LF200A/400A/800A and SST39VF200A/400A/800A provide both hardware and software features to protect nonvolatile data from inadvertent writes. © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 8 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Hardware Data Protection Noise/Glitch Protection: A WE# or CE# pulse of less than 5 ns will not initiate a write cycle. VDD Power Up/Down Detection: The Write operation is inhibited when VDD is less than 1.5V. Write Inhibit Mode: Forcing OE# low, CE# high, or WE# high will inhibit the Write operation. This prevents inadvertent writes during power-up or power-down. Software Data Protection (SDP) The SST39LF200A/400A/800A and SST39VF200A/400A/800A provide the JEDEC approved Software Data Protection scheme for all data alteration operations, i.e., Program and Erase. Any Program operation requires the inclusion of the three-byte sequence. The three-byte load sequence is used to initiate the Program operation, providing optimal protection from inadvertent Write operations, e.g., during the system power-up or power-down. Any Erase operation requires the inclusion of six-byte sequence. This group of devices are shipped with the Software Data Protection permanently enabled. See Table 4 for the specific software command codes. During SDP command sequence, invalid commands will abort the device to Read mode within TRC. The contents of DQ15-DQ8 can be VIL or VIH, but no other value, during any SDP command sequence. Common Flash Memory Interface (CFI) The SST39LF200A/400A/800A and SST39VF200A/400A/800A also contain the CFI information to describe the characteristics of the device. In order to enter the CFI Query mode, the system must write three-byte sequence, same as Software ID Entry command with 98H (CFI Query command) to address 5555H in the last byte sequence. Once the device enters the CFI Query mode, the system can read CFI data at the addresses given in Tables 5 through 9. The system must write the CFI Exit command to return to Read mode from the CFI Query mode. Product Identification The Product Identification mode identifies the devices as the SST39LF/VF200A, SST39LF/VF400A and SST39LF/VF800A and manufacturer as SST. This mode may be accessed by software operations. Users may use the Software Product Identification operation to identify the part (i.e., using the device ID) when using multiple manufacturers in the same socket. For details, see Table 4 for software operation, Figure 13 for the Software ID Entry and Read timing diagram, and Figure 20 for the Software ID Entry command sequence flowchart. Table 2: Product Identification Address Manufacturer’s ID Device ID SST39LF/VF200A SST39LF/VF400A SST39LF/VF800A 0001H 0001H 0001H 2789H 2780H 2781H T2.3 25001 Data 00BFH 0000H © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 9 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Product Identification Mode Exit/CFI Mode Exit In order to return to the standard Read mode, the Software Product Identification mode must be exited. Exit is accomplished by issuing the Software ID Exit command sequence, which returns the device to the Read mode. This command may also be used to reset the device to the Read mode after any inadvertent transient condition that apparently causes the device to behave abnormally, e.g., not read correctly. Please note that the Software ID Exit/CFI Exit command is ignored during an internal Program or Erase operation. See Table 4 for software command codes, Figure 15 for timing waveform, and Figure 20 for a flowchart. Operations Table 3: Operation Modes Selection Mode Read Program Erase Standby Write Inhibit Product Identification Software Mode VIL VIL VIH See Table 4 T3.4 25001 CE# VIL VIL VIL VIH X X OE# VIL VIH VIH X VIL X WE# VIH VIL VIL X X VIH DQ DOUT DIN X1 High Z High Z/ DOUT High Z/ DOUT Address AIN AIN Sector or Block address, XXH for Chip-Erase X X X 1. X can be VIL or VIH, but no other value. Table 4: Software Command Sequence Command Sequence 1st Bus Write Cycle Addr 1 2nd Bus Write Cycle Data Addr1 2AAAH 2AAAH 2AAAH 2AAAH 2AAAH 2AAAH 2 3rd Bus Write Cycle Addr 1 4th Bus Write Cycle Addr 1 5th Bus Write Cycle Data Addr1 2AAAH 2AAAH 2AAAH 2 6th Bus Write Cycle Addr 1 Data 2 Data 2 Data 2 Data 2 Word-Program Sector-Erase Block-Erase Chip-Erase Software ID Entry5,6 CFI Query Entry5 Software ID Exit7/ CFI Exit 5555H AAH 5555H AAH 5555H AAH 5555H AAH 5555H AAH 5555H AAH XXH F0H 55H 55H 55H 55H 55H 55H 5555H 5555H 5555H 5555H 5555H 5555H A0H 80H 80H 80H 90H 98H WA3 5555H 5555H 5555H Data AAH AAH AAH 55H 55H 55H SAX4 BAX4 5555H 30H 50H 10H Software ID Exit7/ 5555H AAH CFI Exit 2AAAH 55H 5555H F0H T4.3 25001 1. Address format A14-A0 (Hex), Addresses AMS-A15 can be VIL or VIH, but no other value, for the Command sequence. AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A, and A18 for SST39LF/VF800A 2. DQ15-DQ8 can be VIL or VIH, but no other value, for the Command sequence 3. WA = Program word address © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 10 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet 4. SAX for Sector-Erase; uses AMS-A11 address lines BAX for Block-Erase; uses AMS-A15 address lines 5. The device does not remain in Software Product ID mode if powered down. SST Manufacturer’s ID = 00BFH, is read with A0 = 0, 6. With AMS-A1 = 0; SST39LF/VF200A Device ID = 2789H, is read with A0 = 1. SST39LF/VF400A Device ID = 2780H, is read with A0 = 1. SST39LF/VF800A Device ID = 2781H, is read with A0 = 1. 7. Both Software ID Exit operations are equivalent Table 5: CFI Query Identification String1 for SST39LF200A/400A/800A and SST39VF200A/400A/800A Address 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH Data 0051H 0052H 0059H 0001H 0007H 0000H 0000H 0000H 0000H 0000H 0000H Data Query Unique ASCII string “QRY” Primary OEM command set Address for Primary Extended Table Alternate OEM command set (00H = none exists) Address for Alternate OEM extended Table (00H = none exits) T5.0 25001 1. Refer to CFI publication 100 for more details. Table 6: System Interface Information for SST39LF200A/400A/800A and SST39VF200A/ 400A/800A Address 1BH 1CH 1DH 1EH 1FH 20H 21H 22H 23H 24H 25H 26H Data 0027H1 0030H1 0036H 0000H 0000H 0004H 0000H 0004H 0006H 0001H 0000H 0001H 0001H Data VDD Min (Program/Erase) DQ7-DQ4: Volts, DQ3-DQ0: 100 millivolts VDD Max (Program/Erase) DQ7-DQ4: Volts, DQ3-DQ0: 100 millivolts VPP min (00H = no VPP pin) VPP max (00H = no VPP pin) Typical time out for Word-Program 2N µs (24 = 16 µs) Typical time out for min size buffer program 2N µs (00H = not supported) Typical time out for individual Sector/Block-Erase 2N ms (24 = 16 ms) Typical time out for Chip-Erase 2N ms (26 = 64 ms) Maximum time out for Word-Program 2N times typical (21 x 24 = 32 µs) Maximum time out for buffer program 2N times typical Maximum time out for individual Sector/Block-Erase 2N times typical (21 x 24 = 32 ms) Maximum time out for Chip-Erase 2N times typical (21 x 26 = 128 ms) T6.2 25001 1. 0030H for SST39LF200A/400A/800A and 0027H for SST39VF200A/400A/800A © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 11 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Table 7: Device Geometry Information for SST39LF/VF200A Address 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H Data 0012H 0001H 0000H 0000H 0002H 003FH 0000H 0010H 0000H 0003H 0000H 0000H 0001H Data Device size = 2N Byte (12H = 18; 218 = 256 KByte) Flash Device Interface description; 0001H = x16-only asynchronous interface Maximum number of bytes in multi-byte write = 2N (00H = not supported) Number of Erase Sector/Block sizes supported by device Sector Information (y + 1 = Number of sectors; z x 256B = sector size) y = 63 + 1 = 64 sectors (003FH = 63) z = 16 x 256 Bytes = 4 KByte/sector (0010H = 16) Block Information (y + 1 = Number of blocks; z x 256B = block size) y = 3 + 1 = 4 blocks (0003H = 3) z = 256 x 256 Bytes = 64 KByte/block (0100H = 256) T7.2 25001 Table 8: Device Geometry Information for SST39LF/VF400A Address 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H Data 0013H 0001H 0000H 0000H 0000H 0002H 007FH 0000H 0010H 0000H 0007H 0000H 0000H 0001H Data Device size = 2N Byte (13H = 19; 219 = 512 KByte) Flash Device Interface description; 0001H = x16-only asynchronous interface Maximum number of bytes in multi-byte write = 2N (00H = not supported) Number of Erase Sector/Block sizes supported by device Sector Information (y + 1 = Number of sectors; z x 256B = sector size) y = 127 + 1 = 128 sectors (007FH = 127) z = 16 x 256 Bytes = 4 KByte/sector (0010H = 16) Block Information (y + 1 = Number of blocks; z x 256B = block size) y = 7 + 1 = 8 blocks (0007H = 7) z = 256 x 256 Bytes = 64 KByte/block (0100H = 256) T8.1 25001 © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 12 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Table 9: Device Geometry Information for SST39LF/VF800A Address 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H Data 0014H 0001H 0000H 0000H 0000H 0002H 00FFH 0000H 0010H 0000H 000FH 0000H 0000H 0001H Data Device size = 2N Bytes (14H = 20; 220 = 1 MByte) Flash Device Interface description; 0001H = x16-only asynchronous interface Maximum number of bytes in multi-byte write = 2N (00H = not supported) Number of Erase Sector/Block sizes supported by device Sector Information (y + 1 = Number of sectors; z x 256B = sector size) y = 255 + 1 = 256 sectors (00FFH = 255) z = 16 x 256 Bytes = 4 KByte/sector (0010H = 16) Block Information (y + 1 = Number of blocks; z x 256B = block size) y = 15 + 1 = 16 blocks (000FH = 15) z = 256 x 256 Bytes = 64 KByte/block (0100H = 256) T9.0 25001 © 2011 Silicon Storage Technology, Inc. DS25001A 03/11 13 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash A Microchip Technology Company SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.) Temperature Under Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C D. C. Voltage on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V Transient Voltage (