TC3683EUA

Obsolete Device TC3682/TC3683/TC3684 Inverting Charge Pump Voltage Doublers with Active Low Shutdown Features • • • • • • • Small 8-Pin MSOP Package Operates from 1.8V to 5.5V 120 Ohms (typ) Output Resistance 99% Voltage Conversion Efficiency Only 3 External Capacitors Required Power-Saving Shutdown Mode Low Active Supply Current - 95μA (typ) for TC3682 - 225μA (typ) for TC3683 - 700μA (typ) for TC3684 • Fully Compatible with 1.8V Logic Systems General Description The TC3682/TC3683/TC3684 are CMOS charge pump converters that provide an inverted doubled output from a single positive supply. An on-board oscillator provides the clock and only three external capacitors are required for full circuit implementation. Switching frequencies are 12kHz for the TC3682, 35kHz for the TC3683, and 125kHz for the TC3684. When the SHDN pin is held at a logic low, the device goes into a very low power mode of operation consuming less than 1μA (typ) of supply current. Low output source impedance (typically 120Ω), provides output current up to 10mA. The TC3682/TC3683/ TC3684 feature a 1.8V to 5.5V operating voltage range and high efficiency, which make them an ideal choice for a wide variety of applications requiring a negative doubled voltage derived from a single positive supply (for example: generation of -7.2V from a +3.6V lithium cell or -10V generated from a +5V logic supply). The minimum external part count, small physical size and shutdown mode feature make this family of products useful for a wide variety of negative bias power supply applications. Operating Temp. Range -40°C to +85°C -40°C to +85°C -40°C to +85°C + C2 C2– Applications • • • • • LCD Panel Bias Cellular Phones PA Bias Pagers PDAs, Portable Data Loggers Battery-Powered Devices Device Selection Table Part Number Package Osc. Freq. (kHz) 12 35 125 Functional Block Diagram + C1 C1+ C1– C2+ VIN SHDN Input ON OFF TC3682EUA 8-Pin MSOP TC3683EUA 8-Pin MSOP TC3684EUA 8-Pin MSOP Package Type 8-Pin MSOP C1– C2+ C2– VOUT 1 2 3 4 8 SHDN C1+ VIN GND TC3682 TC3683 TC3684 VOUT GND VOUT = -(2 x VIN) –C OUT + TC3682 TC3683 TC3684 7 6 5 C1 must have a voltage rating ≥ VIN C2 and COUT must have a voltage rating ≥ 2VIN © 2005 Microchip Technology Inc. DS21556C-page 1 TC3682/TC3683/TC3684 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings* Input Voltage (VIN to GND)....................... +6.0V, -0.3V Output Voltage (VOUT to GND)............... -12.0V, +0.3V Current at VOUT Pin.............................................20mA Short-Circuit Duration VOUT to GND ..............Indefinite Power Dissipation (TA ≤ 70°C) 8-Pin MSOP .............................................320mW Operating Temperature Range.............-40°C to +85°C Storage Temperature (Unbiased) .......-65°C to +150°C *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. TC3682/TC3683/TC3684 ELECTRICAL SPECIFICATIONS Electrical Characteristics: TA = -40°C to +85°C, VIN = +5V, C1 = C2 = 3.3μF (TC3682), C1 = C2 = 1μF (TC3683), C1 = C2 = 0.33μF (TC3684), SHDN = GND, Typical values are at TA = +25°C Symbol IDD Parameter Supply Current Min — — — — 1.8 — 8.4 24.5 65 1.4 — 95 — — — — Typ 95 225 700 0.5 — — 12 35 125 — — 99 120 1800 600 200 Max 160 480 1500 2 — 5.5 15.6 45.5 170 — 0.4 — 170 — — — Units μA Device TC3682 TC3683 TC3684 All All All TC3682 TC3683 TC3684 All All All All TC3682 TC3683 TC3684 VIN = VMIN to VMAX VIN = VMIN to VMAX RLOAD = ∞ ILOAD = 0.5mA to 10mA (Note 1) RLOAD = 2kΩ Test Conditions SHDN = VIN SHDN = VIN SHDN = VIN SHDN = GND, VIN = +5V RLOAD = 1kΩ RLOAD = 1kΩ ISHDN VMIN VMAX FOSC Shutdown Supply Current Minimum Supply Voltage Maximum Supply Voltage Oscillator Frequency μA V V kHz VIH VIL VEFF ROUT TWK SHDN Input Logic High SHDN Input Logic Low Voltage Conversion Efficiency Output Resistance Wake-up Time From Shutdown Mode V V % Ω μsec Note 1: Capacitor contribution is approximately 20% of the output impedance (ESR = 1/ pump frequency x capacitance). DS21556C-page 2 © 2005 Microchip Technology Inc. TC3682/TC3683/TC3684 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: Pin No. (8-Pin MSOP) 1 2 3 4 5 6 7 8 PIN FUNCTION TABLE Symbol C1– C2+ C2– VOUT GND VIN C1+ SHDN Description C1 commutation capacitor negative terminal. C2 commutation capacitor positive terminal. C2 commutation capacitor negative terminal. Doubling inverting charge pump output (-2 x VIN). Ground. Positive power supply input. C1 commutation capacitor positive terminal. Shutdown input (active low). © 2005 Microchip Technology Inc. DS21556C-page 3 TC3682/TC3683/TC3684 3.0 DETAILED DESCRIPTION The TC3682/TC3683/TC3684 inverting charge pumps perform a -2x multiplication of the voltage applied to the VIN pin. Conversion is performed using two synchronous switching matrices and three external capacitors. When the shutdown input is held at a logic low, the device goes into a very low power mode of operation consuming less than 1μA of supply current. Figure 3-1 is a block diagram representation of the TC3682/TC3683/TC3684 architecture. The first switching stage inverts the voltage present at VIN and the second stage uses the ‘-VIN’ output generated from the first stage to produce the ‘-2X’ output function from the second stage switching matrix. Each device contains an on-board oscillator that synchronously controls the operation of the charge pump switching matrices. The TC3682 synchronously switches at 12kHz, the TC3683 synchronously switches at 35kHz, and the TC3684 synchronously switches at 125kHz. The different oscillator frequencies for this device family allow the user to trade-off capacitor size versus supply current. Faster oscillators can use smaller external capacitors, but will consume more supply current (see Section 1.0 Electrical Characteristics). When the shutdown input is in a low state, the oscillator and both switch matrices are powered off placing the TC3682/TC3683/TC3684 in the shutdown mode. When the VIN supply input is powered from an external battery, the shutdown mode minimizes power consumption, which in turn will extend the life of the battery. FIGURE 3-1: TC3682/TC3683/TC3684 ARCHITECTURE VIN + C1 Switch Matrix (1st Stage) + ENABLE -VIN COUT1 Oscillator ENABLE + C2 Switch Matrix (2nd Stage) -2VIN COUT2 + ENABLE SHDN DS21556C-page 4 © 2005 Microchip Technology Inc. TC3682/TC3683/TC3684 4.0 4.1 APPLICATIONS INFORMATION Output Voltage Considerations 4.3 Input Supply Bypassing The TC3682/TC3683/TC3684 perform inverting voltage conversions but do not provide any type of regulation. The output voltage will droop in a linear manner with respect to the output load current. The value of the equivalent output resistance of the ‘-VIN’ output is approximately 50Ω nominal at +25°C and VIN = +5V. The value of the ‘-2VIN’ output is approximately 140Ω nominal at +25°C and VIN = +5V. In this particular case, ‘-VIN’ is approximately -5V and ‘-2VIN’ is approximately -10V at very light loads and each stage will droop according to the equation below: VDROOP = IOUT x ROUT The VIN input should be capacitively bypassed to reduce AC impedance and minimize noise effects due to the switching internal to the device. It is recommended that a large value capacitor (at least equal to C1) be connected from VIN to GND for optimal circuit performance. 4.4 Shutdown Input The TC3682/TC3683/TC3684 is enabled when SHDN is high, and disabled when SHDN is low. This input cannot be allowed to float. (If SHDN is not required, see the TC2682/TC2683/TC2684 data sheet.) The SHDN input should be limited to 0.3V above VIN. 4.2 Capacitor Selection 4.5 Inverting Voltage Doubler In order to maintain the lowest output resistance and output ripple voltage, it is recommended that low ESR capacitors be used. Additionally, larger values of C1 and C2 will lower the output resistance and larger values of COUT will reduce output ripple. Note: For proper charge pump operation, C1 must have a voltage rating greater than or equal to VIN, while C2 and COUT must have a voltage rating greater than or equal to 2VIN. The most common application for the TC3682/TC3683/ TC3684 devices is the inverting voltage doubler (Figure 4-1). This application uses three external capacitors: C1, C2 and COUT. Note: A power supply bypass capacitor is recommended. The output is equal to -2VIN plus any voltage drops due to loading. Refer to Table 4-1 and Table 4-2 for capacitor selection guidelines. Table 4-1 shows various values of C1/C2 and the corresponding output resistance values for VIN = 5V @ +25°C. Table 4-2 shows the output voltage ripple for various values of COUT (again assuming VIN = 5V @ +25°C). The VRIPPLE values assume a 1mA output load current and a 0.1Ω ESRCOUT. FIGURE 4-1: VIN CIN INVERTING VOLTAGE DOUBLER TEST CIRCUIT + 6 VIN 8 SHDN + C1 7 C1+ 1 TABLE 4-1: C1, C2 (μF) 0.33 1 3.3 OUTPUT RESISTANCE VS. C1/C2 (ESR = 0.1Ω) TC3682 ROUT(Ω) 633 262 120 TC3683 ROUT(Ω) 184 120 95 TC3684 ROUT(Ω) 120 102 84 + C2 TC3682 TC3683 2 C2+ TC3684 C1– -2VIN 3 C2– GND 5 4 COUT + RL VOUT Device TC3682 TC3683 TC3684 CIN 3.3μF 1μF 0.33μF C1 3.3μF 1μF 0.33μF C2 3.3μF 1μF 0.33μF COUT 3.3μF 1μF 0.33μF TABLE 4-2: OUTPUT VOLTAGE RIPPLE VS. COUT (ESR = 0.1Ω) IOUT = 1mA TC3682 VRIPPLE (mV) 192 63 17 TC3683 VRIPPLE (mV) 60 21 8 TC3684 VRIPPLE (mV) 27 16 7 4.6 Layout Considerations COUT (μF) 0.33 1 3.3 As with any switching power supply circuit, good layout practice is recommended. Mount components as close together as possible to minimize stray inductance and capacitance. Also use a large ground plane to minimize noise leakage into other circuitry. © 2005 Microchip Technology Inc. DS21556C-page 5 TC3682/TC3683/TC3684 5.0 5.1 PACKAGING INFORMATION Package Marking Information Package marking data not available at this time. 5.2 Taping Form Component Taping Orientation for 8-Pin MSOP Devices User Direction of Feed PIN 1 P Standard Reel Component Orientation for TR Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 8-Pin MSOP 12 mm 8 mm 2500 13 in 5.3 Package Dimensions 8-Pin MSOP PIN 1 .122 (3.10) .114 (2.90) .197 (5.00) .189 (4.80) .026 (0.65) TYP. .122 (3.10) .114 (2.90) .043 (1.10) MAX. .016 (0.40) .010 (0.25) .006 (0.15) .002 (0.05) 6° MAX. .028 (0.70) .016 (0.40) .008 (0.20) .005 (0.13) Dimensions: inches (mm) DS21556C-page 6 © 2005 Microchip Technology Inc. TC3682/TC3683/TC3684 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. © 2005 Microchip Technology Inc. DS21556C-page7 TC3682/TC3683/TC3684 NOTES: DS21556C-page8 © 2005 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • • Microchip products meet the specification contained in their particular Microchip Data Sheet. Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” • • • Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB, PICMASTER, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active Thermistor, MPASM, MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance and WiperLock are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2005, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona and Mountain View, California in October 2003. The Company’s quality system processes and procedures are for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2005 Microchip Technology Inc. DS21556C-page 9 WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Atlanta Alpharetta, GA Tel: 770-640-0034 Fax: 770-640-0307 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 San Jose Mountain View, CA Tel: 650-215-1444 Fax: 650-961-0286 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 ASIA/PACIFIC Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8676-6200 Fax: 86-28-8676-6599 China - Fuzhou Tel: 86-591-8750-3506 Fax: 86-591-8750-3521 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 China - Shunde Tel: 86-757-2839-5507 Fax: 86-757-2839-5571 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7250 Fax: 86-29-8833-7256 ASIA/PACIFIC India - Bangalore Tel: 91-80-2229-0061 Fax: 91-80-2229-0062 India - New Delhi Tel: 91-11-5160-8631 Fax: 91-11-5160-8632 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Korea - Gumi Tel: 82-54-473-4301 Fax: 82-54-473-4302 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Malaysia - Penang Tel: 60-4-646-8870 Fax: 60-4-646-5086 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 EUROPE Austria - Wels Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 10/31/05 DS21556C-page 10 © 2005 Microchip Technology Inc.