TC7660SEOA

EVALUATION KIT AVAILABLE TC7660S SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER FEATURES s s s s s s s s s s Oscillator boost from 10kHz to 45kHz Converts +5V Logic Supply to ±5V System Wide Input Voltage Range .................... 1.5V to 12V Efficient Voltage Conversion ......................... 99.9% Excellent Power Efficiency ............................... 98% Low Power Supply .............................. 80µA @ 5 VIN Low Cost and Easy to Use — Only Two External Capacitors Required Available in Small Outline (SOIC) Package Improved ESD Protection ..................... Up to 10kV No External Diode Required for High Voltage Operation GENERAL DESCRIPTION The TC7660S is a pin-compatible upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding -1.5V to -12V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and EMI. Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10kHz. Frequency is increased to 45kHz when pin 1 is connected to V+. Operation below 10kHz (for lower supply current applications) is possible by connecting an external capacitor from OSC to ground (with pin 1 open). The TC7660S is available in both 8-pin DIP and 8-pin small outline (SOIC) packages in commercial and extended temperature ranges. PIN CONFIGURATION (DIP AND SOIC) 8 V+ 7 OSC 8 V+ 7 OSC LOW TC7660SCOA 6 VOLTAGE (LV) TC7660SEOA 5 VOUT ORDERING INFORMATION Part No. TC7660SCOA TC7660SCPA TC7660SEJA TC7660SEOA TC7660SEPA TC7660SMJA Package 8-Pin SOIC 8-Pin Plastic DIP 8-Pin CerDIP 8-Pin SOIC 8-Pin Plastic DIP 8-Pin CerDIP Temperature Range 0°C to +70°C 0°C to +70°C – 40°C to +85°C – 40°C to +85°C – 40°C to +85°C – 55°C to +125°C Boost 1 CAP + 2 Boost CAP + GND CAP – 1 2 3 4 GND 3 TC7660SCPA 6 LOW VOLTAGE (LV) TC7660SEJA CAP – 4 TC7660SEPA 5 VOUT TC7660EV Evaluation Kit for Charge Pump Family FUNCTIONAL BLOCK DIAGRAM V + CAP + 8 BOOST 1 2 OSC 7 RC OSCILLATOR ÷2 VOLTAGE– LEVEL TRANSLATOR 4 CAP – LV 6 5 INTERNAL VOLTAGE REGULATOR LOGIC NETWORK VOUT TC7660S 3 GND © 2001 Microchip Technology Inc. DS21467A TC7660S-14 9/16/96 SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S ABSOLUTE MAXIMUM RATINGS* Supply Voltage ......................................................... +13V LV, Boost, OSC Inputs Voltage (Note 1) ......................... – 0.3V to (V+ +0.3V) for V+ < 5.5V + – 5.5V) to (V+ +0.3V) (V for V+ > 5.5V Current Into LV (Note 1) ...................... 20µA for V+ > 3.5V Output Short Duration (VSUPPLY ≤ 5.5V) ......... Continuous Power Dissipation (TA ≤ 70°C) (Note 2) CerDIP ............................................................800mW Plastic DIP ......................................................730mW SOIC ...............................................................470mW Operating Temperature Range C Suffix .................................................. 0°C to +70°C E Suffix ............................................. – 40°C to +85°C M Suffix ........................................... – 55°C to +125°C Storage Temperature Range ................ – 65°C to +150°C Lead Temperature (Soldering, 10 sec) ................. +300°C *Static-sensitive device. Unused devices must be stored in conductive material. Protect devices from static discharge and static fields. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS: TA = +25°C, V+ = 5V, COSC = 0, Test Circuit (Figure 1), unless otherwise indicated. Symbol I + Parameter Supply Current (Boost pin OPEN or GND) Test Conditions RL = ∞ 0°C ≤ TA ≤ +70°C – 40°C ≤ TA ≤ +85°C – 55°C ≤ TA ≤ +125°C 0°C ≤ TA ≤ +70°C – 40°C ≤ TA ≤ +85°C – 55°C ≤ TA ≤ +125°C Min ≤ TA ≤ Max, RL = 10kΩ, LV Open Min ≤ TA ≤ Max, RL = 10kΩ, LV to GND IOUT = 20mA IOUT = 20mA, 0°C ≤ TA ≤ +70°C IOUT = 20mA, – 40°C ≤ TA ≤ +85°C IOUT = 20mA, – 55°C ≤ TA ≤ +125°C V+ = 2V, IOUT = 3mA, LV to GND 0°C ≤ TA ≤ +70°C – 55°C ≤ TA ≤ +125°C Pin 7 open; Pin 1 open or GND Boost Pin = V+ RL = 5 kΩ; Boost Pin Open TMIN ≤ TA ≤ TMAX; Boost Pin Open Boost Pin = V+ RL = ∞ V+ = 2V V+ = 5V Min — — — — — — — 3 1.5 — — — — — — — — 96 95 — 99 — — Typ 80 — — — — — — — — 60 70 70 105 — — 10 45 98 98 88 99.9 1 100 Max 160 180 180 200 300 350 400 12 3.5 100 120 120 150 250 400 — — — — — — — — Unit µA I+ Supply Current (Boost pin = V+) Supply Voltage Range, High Supply Voltage Range, Low Output Source Resistance µA V+H V+L ROUT V V Ω Ω kHz % FOSC PEFF Oscillator Frequency Power Efficiency VOUT EFF ZOSC Voltage Conversion Efficiency Oscillator Impedance % MΩ kΩ NOTES: 1. Connecting any input terminal to voltages greater than V+ or less than GND may cause destructive latch-up. It is recommended that no inputs from sources operating from external supplies be applied prior to "power up" of the TC7660S. 2. Derate linearly above 50°C by 5.5mW/°C. TC7660S-14 9/16/96 2 © 2001 Microchip Technology Inc. DS21467A SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S Detailed Description The TC7660S contains all the necessary circuitry to implement a voltage inverter, with the exception of two external capacitors, which may be inexpensive 10 µF polarized electrolytic capacitors. Operation is best understood by considering Figure 2, which shows an idealized voltage inverter. Capacitor C1 is charged to a voltage V+ for the half cycle when switches S1 and S3 are closed. (Note: Switches S2 and S4 are open during this half cycle.) During the second half cycle of operation, switches S2 and S4 are closed, with S1 and S3 open, thereby shifting capacitor C1 negatively by V+ volts. Charge is then transferred from C1 negatively by V+ volts. Charge is then transferred from C1 to C2, such that the voltage on C2 is exactly V+, assuming ideal switches and no load on C2. The four switches in Figure 2 are MOS power switches; S1 is a P-channel device, and S2, S3 and S4 are N-channel devices. The main difficulty with this approach is that in integrating the switches, the substrates of S3 and S4 must always remain reverse-biased with respect to their sources, but not so much as to degrade their ON resistances. In addition, at circuit start-up, and under output short circuit conditions (VOUT = V+), the output voltage must be sensed and the substrate bias adjusted accordingly. Failure to accomplish this will result in high power losses and probable device latch-up. This problem is eliminated in the TC7660S by a logic network which senses the output voltage (VOUT) together with the level translators, and switches the substrates of S3 and S4 to the correct level to maintain necessary reverse bias. V+ S1 S2 C1 GND S3 S4 C2 VOUT = – VIN Figure 2. Idealized Charge Pump Inverter The voltage regulator portion of the TC7660S is an integral part of the anti-latch-up circuitry. Its inherent voltage drop can, however, degrade operation at low voltages. To improve low-voltage operation, the “LV” pin should be connected to GND, disabling the regulator. For supply voltages greater than 3.5V, the LV terminal must be left open to ensure latch-up-proof operation and prevent device damage. Theoretical Power Efficiency Considerations In theory, a capacitive charge pump can approach 100% efficiency if certain conditions are met: (1) The drive circuitry consumes minimal power. (2) The output switches have extremely low ON resistance and virtually no offset. V+ 1 2 C1 10µF + 3 4 8 7 IS V+ (+5V) (3) The impedances of the pump and reservoir capacitors are negligible at the pump frequency. The TC7660S approaches these conditions for negative voltage multiplication if large values of C1 and C2 are used. Energy is lost only in the transfer of charge between capacitors if a change in voltage occurs. The energy lost is defined by: E = 1/2 C1 (V12 – V22) V1 and V2 are the voltages on C1 during the pump and transfer cycles. If the impedances of C1 and C2 are relatively high at the pump frequency (refer to Figure 2) compared to the value of RL, there will be a substantial difference in voltages V1 and V2. Therefore, it is desirable not only to make C2 as large as possible to eliminate output voltage ripple, but also to employ a correspondingly large value for C1 in order to achieve maximum efficiency of operation. 3 TC7660S-14 9/16/96 TC7660S 6 5 COSC* IL RL VO C2 10µF + NOTE: For large values of COSC (>1000pF), the values of C1 and C2 should be increased to 100 F. Figure 1. TC7660S Test Circuit © 2001 Microchip Technology Inc. DS21467A SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S Dos and Don'ts • Do not exceed maximum supply voltages. • Do not connect the LV terminal to GND for supply voltages greater than 3.5V. • Do not short circuit the output to V+ supply for voltages above 5.5V for extended periods; however, transient conditions including start-up are okay. • When using polarized capacitors in the inverting mode, the + terminal of C1 must be connected to pin 2 of the TC7660S and the + terminal of C2 must be connected to GND. The output characteristics of the circuit in Figure 3 are those of a nearly ideal voltage source in series with 70Ω. Thus, for a load current of –10mA and a supply voltage of +5V, the output voltage would be – 4.3V. The dynamic output impedance of the TC7660S is due, primarily, to capacitive reactance of the charge transfer capacitor (C1). Since this capacitor is connected to the output for only 1/2 of the cycle, the equation is: 2 XC = = 3.18Ω, 2πf C1 where f = 10kHz and C1 = 10µF. Paralleling Devices Simple Negative Voltage Converter Figure 3 shows typical connections to provide a negative supply where a positive supply is available. A similar scheme may be employed for supply voltages anywhere in the operating range of +1.5V to +12V, keeping in mind that pin 6 (LV) is tied to the supply negative (GND) only for supply voltages below 3.5V. V+ 1 C1 10µF + 2 3 4 8 7 VOUT* C2 10µF Any number of TC7660S voltage converters may be paralleled to reduce output resistance (Figure 4). The reservoir capacitor, C2, serves all devices, while each device requires its own pump capacitor, C1. The resultant output resistance would be approximately: ROUT (of TC7660S) n (number of devices) ROUT = TC7660S 6 5 + * NOTES: Figure 3. Simple Negative Converter V+ 1 2 C1 3 4 8 7 1 2 C1 3 4 8 7 RL TC7660S "1" 6 5 TC7660S "n" 6 5 + C2 Figure 4. Paralleling Devices Lowers Output Impedance TC7660S-14 9/16/96 4 © 2001 Microchip Technology Inc. DS21467A SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S + V 1 2 10µF + 3 4 TC7660S "1" 8 7 6 5 10µF + 1 2 3 4 TC7660S "n" 8 7 6 5 + VOUT* 10µF * NOTES: 1. VOUT = –n(V+) for 1.5V ≤ V+ ≤ 12V + 10µF Figure 5. Increased Output Voltage by Cascading Devices Cascading Devices The TC7660S may be cascaded as shown (Figure 5) to produce larger negative multiplication of the initial supply voltage. However, due to the finite efficiency of each device, the practical limit is 10 devices for light loads. The output voltage is defined by: VOUT = – n (VIN) where n is an integer representing the number of devices cascaded. The resulting output resistance would be approximately the weighted sum of the individual TC7660S ROUT values. Changing the TC7660S Oscillator Frequency It may be desirable in some applications (due to noise or other considerations) to increase the oscillator frequency. Pin 1, frequency boost pin may be connected to V+ to increase oscillator frequency to 45kHz from a nominal of 10kHz for an input supply voltage of 5.0 volts. The oscillator may also be synchronized to an external clock as shown in Figure 6. In order to prevent possible device latch-up, a 1kΩ resistor must be used in series with the clock output. In a V+ 1 2 10µF + 3 4 TC7660S 8 7 6 5 + 10µF VOUT 1 kΩ V+ CMOS GATE situation where the designer has generated the external clock frequency using TTL logic, the addition of a 10kΩ pullup resistor to V+ supply is required. Note that the pump frequency with external clocking, as with internal clocking, will be ¹⁄₂ of the clock frequency. Output transitions occur on the positive-going edge of the clock. It is also possible to increase the conversion efficiency of the TC7660S at low load levels by lowering the oscillator frequency. This reduces the switching losses, and is achieved by connecting an additional capacitor, COSC, as shown in Figure 7. Lowering the oscillator frequency will cause an undesirable increase in the impedance of the pump (C1) and the reservoir (C2) capacitors. To overcome this, increase the values of C1 and C2 by the same factor that the frequency has been reduced. For example, the addition of a 100pF capacitor between pin 7 (OSC) and pin 8 (V+) will lower the oscillator frequency to 1kHz from its nominal frequency of 10kHz (a multiple of 10), and necessitate a corresponding increase in the values of C1 and C2 (from 10µF to 100µF). Positive Voltage Multiplication The TC7660S may be employed to achieve positive voltage multiplication using the circuit shown in Figure 8. In this application, the pump inverter switches of the TC7660S are used to charge C1 to a voltage level of V+–VF (where V+ is the supply voltage and VF is the forward voltage drop of diode D1). On the transfer cycle, the voltage on C1 plus the supply voltage (V+) is applied through diode D2 to capacitor C2. The voltage thus created on C2 becomes (2V+) – (2VF), or twice the supply voltage minus the combined forward voltage drops of diodes D1 and D2. The source impedance of the output (VOUT) will depend on the output current, but for V+ = 5V and an output current of 10mA, it will be approximately 60Ω. Figure 6. External Clocking © 2001 Microchip Technology Inc. DS21467A 5 TC7660S-14 9/16/96 SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S V 1 2 C1 + 3 4 8 7 + COSC will bypass the other (D1 and D2 in Figure 9 would never turn on), or else the diode and resistor shown dotted in Figure 10 can be used to "force" the internal regulator on. TC7660S Voltage Splitting VOUT + C2 6 5 Figure 7. Lowering Oscillator Frequency Combined Negative Voltage Conversion and Positive Supply Multiplication Figure 9 combines the functions shown in Figures 3 and 8 to provide negative voltage conversion and positive voltage multiplication simultaneously. This approach would be, for example, suitable for generating +9V and – 5V from an existing +5V supply. In this instance, capacitors C1 and C3 perform the pump and reservoir functions, respectively, for the generation of the negative voltage, while capacitors C2 and C4 are pump and reservoir, respectively, for the multiplied positive voltage. There is a penalty in this configuration which combines both functions, however, in that the source impedances of the generated supplies will be somewhat higher due to the finite impedance of the common charge pump driver at pin 2 of the device. The same bidirectional characteristics used in Figure 10 can also be used to split a higher supply in half, as shown in Figure 11. The combined load will be evenly shared between the two sides. Once again, a high value resistor to the LV pin ensures start-up. Because the switches share the load in parallel, the output impedance is much lower than in the standard circuits, and higher currents can be drawn from the device. By using this circuit, and then the circuit of Figure 5, +15V can be converted (via +7.5V and – 7.5V) to a nominal –15V, though with rather high series resistance (~250Ω). V+ VOUT = –V+ 1 2 3 + C1 4 + C2 8 7 + C3 TC7660S 6 5 D1 D2 VOUT = (2 V +) – (2 VF) + C4 Efficient Positive Voltage Multiplication/Conversion Since the switches that allow the charge pumping operation are bidirectional, the charge transfer can be performed backwards as easily as forwards. Figure 10 shows a TC7660S transforming – 5V to +5V (or +5V to +10V, etc.). The only problem here is that the internal clock and switchdrive section will not operate until some positive voltage has been generated. An initial inefficient pump, as shown in Figure 9, could be used to start this circuit up, after which it V+ 1 2 3 4 8 7 D1 D2 + C1 + C2 VOUT = (2 V+) – (2 VF) Figure 9. Combined Negative Converter and Positive Multiplier Negative Voltage Generation for Display ADCs The TC7106 is designed to work from a 9V battery. With a fixed power supply system, the TC7106 will perform conversions with input signal referenced to power supply ground. Negative Supply Generation for 4¹⁄₂ Digit Data Acquisition System The TC7135 is a 4¹⁄₂ digit ADC operating from ±5V supplies. The TC7660S provides an inexpensive –5V source. (See AN16 and AN17 for TC7135 interface details and software routines.) TC7660S 6 5 Figure 8. Positive Voltage Multiplier TC7660S-14 9/16/96 6 © 2001 Microchip Technology Inc. DS21467A SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S VOUT = –V– R L1 50µF + – 50µF V + + 1 2 100 kΩ 8 7 1 MΩ 1 2 C1 10µF + 3 4 8 7 1 MΩ + 10µF TC7660S 6 5 V– INPUT V = OUT + – V –V 2 R L2 3 4 TC7660S 6 5 50µF + – V – Figure 10. Positive Voltage Multiplier Figure 11. Splitting a Supply in Half TYPICAL CHARACTERISTICS Unloaded Osc Freq vs. Temperature 12 OSCILLATOR FREQUENCY (kHz) 60 OSCILLATOR FREQUENCY (kHz) Unloaded Osc Freq vs. Temperature with Boost Pin = VIN 10 8 6 4 VIN = 12V 2 0 -40 -20 0 20 40 60 80 100 VIN = 5V 50 40 30 VIN = 12V 20 10 0 -40 -20 0 20 40 60 80 100 VIN = 5V TEMPERATURE (°C) TEMPERATURE (°C) 1000 800 600 IDD (µA) VOLTAGE CONVERSION EFFICIENCY (%) Supply Current vs. Temperature (with Boost Pin = VIN) Voltage Conversion 101.0 100.5 100.0 99.5 99.0 98.5 TA = 25°C 98.0 1 2 3 4 5 6 7 8 9 10 11 12 INPUT VOLTAGE VIN (V) Without Load VIN = 12V 400 200 0 -40 10K Load VIN = 5V -20 0 20 DS21467A 40 60 80 100 7 TEMPERATURE (°C) © 2001 Microchip Technology Inc. TC7660S-14 9/16/96 SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S TYPICAL CHARACTERISTICS (Cont.) Output Source Resistance vs. Supply Voltage 100 OUTPUT SOURCE RESISTANCE (Ω) OUTPUT SOURCE RESISTANCE (Ω) Output Source Resistance vs. Temperature 100 80 60 40 20 0 -40 VIN = 2.5V 70 50 30 VIN = 5.5V IOUT = 20mA TA = 25°C 10 1.5 2.5 3.5 4.5 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12 SUPPLY VOLTAGE (V) -20 0 20 40 60 80 100 TEMPERATURE (°C) Output Voltage vs. Output Current 0 OUTPUT VOLTAGE VOUT (V) Power Conversion Efficiency vs. Load 100 90 80 70 60 50 40 30 20 10 0 Boost Pin = Open Boost Pin = V+ -2 -4 -6 -8 -10 -12 POWER EFFICIENCY (%) 0 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA) Supply Current vs. Temperature 200 175 SUPPLY CURRENT IDD (µA) SUPPLY CURRENT IDD (µA) 200 175 150 125 100 75 50 25 0 -40 -20 0 20 40 60 80 100 VIN = 5.5V VIN = 12.5V 150 125 100 75 50 25 0 -40 -20 0 20 40 60 80 100 8 VIN = 12.5V VIN = 5.5V TEMPERATURE (°C) TC7660S-14 9/16/96 1.0 1.5 2.0 3.0 4.5 6.0 7.5 9.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 50.0 55.0 60.0 LOAD CURRENT (mA) Supply Current vs. Temperature TEMPERATURE (°C) © 2001 Microchip Technology Inc. DS21467A SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S TYPICAL CHARACTERISTICS (Cont.) Supply Current vs. Temperature 200 175 SUPPLY CURRENT IDD (µA) 150 125 100 75 50 25 0 -40 -20 0 20 40 60 80 100 VIN = 5.5V VIN = 12.5V TEMPERATURE (°C) PACKAGE DIMENSIONS 8-Pin Plastic DIP PIN 1 .260 (6.60) .240 (6.10) .045 (1.14) .030 (0.76) .400 (10.16) .348 (8.84) .200 (5.08) .140 (3.56) .150 (3.81) .115 (2.92) .070 (1.78) .040 (1.02) .310 (7.87) .290 (7.37) .040 (1.02) .020 (0.51) .015 (0.38) .008 (0.20) .400 (10.16) .310 (7.87) 3° MIN. .110 (2.79) .090 (2.29) .022 (0.56) .015 (0.38) Dimensions: inches (mm) © 2001 Microchip Technology Inc. DS21467A 9 TC7660S-14 9/16/96 SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S PACKAGE DIMENSIONS (CONT.) 8-Pin CerDIP .110 (2.79) .090 (2.29) PIN 1 .300 (7.62) .230 (5.84) .055 (1.40) MAX. .400 (10.16) .370 (9.40) .200 (5.08) .160 (4.06) .200 (5.08) .125 (3.18) .020 (0.51) MIN. .320 (8.13) .290 (7.37) .040 (1.02) .020 (0.51) .015 (0.38) .008 (0.20) .400 (10.16) .320 (8.13) .065 (1.65) .020 (0.51) .045 (1.14) .016 (0.41) .150 (3.81) MIN. 3° MIN. 8-Pin Plastic SOIC .157 (3.99) .150 (3.81) .244 (6.20) .228 (5.79) .050 (1.27) TYP. .197 (5.00) .189 (4.80) .069 (1.75) .053 (1.35) .020 (0.51) .010 (0.25) .013 (0.33) .004 (0.10) 8° MAX. .050 (1.27) .016 (0.40) Dimensions: inches (mm) TC7660S-14 9/16/96 .010 (0.25) .007 (0.18) 10 © 2001 Microchip Technology Inc. DS21467A SUPER CHARGE PUMP DC-TO-DC VOLTAGE CONVERTER TC7660S WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com New York 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 ASIA/PACIFIC (continued) Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Rocky Mountain 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 ASIA/PACIFIC China - Beijing Microchip Technology Beijing Office Unit 915 New China Hong Kong Manhattan Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Austin Analog Product Sales 8303 MoPac Expressway North Suite A-201 Austin, TX 78759 Tel: 512-345-2030 Fax: 512-345-6085 EUROPE Australia Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 China - Shanghai Microchip Technology Shanghai Office Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Denmark Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 Boston Analog Product Sales Unit A-8-1 Millbrook Tarry Condominium 97 Lowell Road Concord, MA 01742 Tel: 978-371-6400 Fax: 978-371-0050 France Arizona Microchip Technology SARL Parc díActivite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Hong Kong Microchip Asia Pacific RM 2101, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 India Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, OíShaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Germany Arizona Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Dayton Two Prestige Place, Suite 130 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Germany Analog Product Sales Lochhamer Strasse 13 D-82152 Martinsried, Germany Tel: 49-89-895650-0 Fax: 49-89-895650-22 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Japan Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Italy Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934 United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 Printed on recycled paper. 01/09/01 Mountain View Analog Product Sales 1300 Terra Bella Avenue Mountain View, CA 94043-1836 Tel: 650-968-9241 Fax: 650-967-1590 All rights reserved. © 2001 Microchip Technology Incorporated. Printed in the USA. 1/01 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchipís products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. © 2001 Microchip Technology Inc. DS21467A 11 TC7660S-14 9/16/96