TC911ACOA

TC911A TC911B Monolithic Auto-Zeroed Operational Amplifers FEATURES s s s s s s s s s s s s First Monolithic Chopper-Stabilized Amplifier With On-Chip Nulling Capacitors Offset Voltage .................................................... 5µV Offset Voltage Drift .................................. 0.05µV/°C Low Supply Current ...................................... 350µA High Common-Mode Rejection .................... 116dB Single Supply Operation ....................... 4.5V to 16V High Slew Rate ......................................... 2.5V/µsec Wide Bandwidth ............................................ 1.5MHz High Open-Loop Voltage Gain (RL = 10kΩ) ..................................................... 120dB Low Input Voltage Noise (0.1Hz to 1Hz) ............................................ 0.65µVP-P Pin Compatible With ICL7650 Lower System Parts Count GENERAL DESCRIPTION The TC911 CMOS auto-zeroed operational amplifier is the first complete monolithic chopper-stabilized amplifier. Chopper operational amplifiers like the ICL7650/7652 and LTC1052 require user-supplied, external offset compensation storage capacitors. External capacitors are not required with the TC911. Just as easy to use as the conventional OP07 type amplifier, the TC911 significantly reduces offset voltage errors. Pinout matches the OP07/ 741/7650 8-pin mini-DIP configuration. Several system benefits arise by eliminating the external chopper capacitors: lower system parts count, reduced assembly time and cost, greater system reliability, reduced PC board layout effort and greater board area utilization. Space savings can be significant in multiple-amplifier designs. Electrical specifications include 15µV maximum offset voltage, 0.15µV/°C maximum offset voltage temperature coefficient. Offset voltage error is five times lower than the premium OP07E bipolar device. The TC911 improves offset drift performance by eight times. The TC911 operates from dual or single power supplies. Supply current is typically 350µA. Single 4.5V to 16V supply operation is possible, making single 9V battery operation possible. The TC911 is available in 2 package types: 8-pin plastic DIP and SOIC. PIN CONFIGURATION (SOIC and DIP) NC 1 – INPUT 2 + INPUT 3 VSS 4 TC911ACPA TC911BCPA 8 NC 7 VDD 6 OUTPUT 5 NC NC 1 – INPUT 2 + INPUT 3 VSS 4 8 NC 7 VDD TC911ACOA TC911BCOA 6 OUTPUT 5 NC ORDERING INFORMATION Temperature Range 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C Part No. TC911ACOA TC911ACPA TC911BCOA TC911BCPA Package 8-Pin SOIC 8-Pin Plastic DIP 8-Pin SOIC 8-Pin Plastic DIP Maximum Offset Voltage 15µV 15µV 30µV 30µV FUNCTIONAL BLOCK DIAGRAM VDD 4 VSS 7 V CORRECTION AMPLIFIER OS A – B B NC = NO INTERNAL CONNECTION –INPUT 2 + INTERNAL OSCILLATOR (fOSC ≈ 200 Hz) * * A +INPUT 3 + TC911 LOW IMPEDANCE OUTPUT BUFFER + – MAIN AMPLIFIER – 6 OUTPUT *NOTE: Internal capacitors. No external capacitors required. © 2001 Microchip Technology Inc. DS21481A TC911/A/B-7 9/11/96 Monolithic Auto-Zeroed Operational Amplifers TC911A TC911/B ABSOLUTE MAXIMUM RATINGS* Total Supply Voltage (VDD to VSS) ........................... +18V Input Voltage .......................... (VDD +0.3V) to (VSS –0.3V) Current into Any Pin ................................................. 10mA While Operating ............................................... 100µA Storage Temperature Range ................ – 65°C to +150°C Lead Temperature (Soldering, 10 sec) ................. +300°C Operating Temperature Range C Device ................................................ 0°C to +70°C Package Power Dissipation (TA ≤ 70°C) Plastic DIP ...................................................... 730mW Plastic SOIC ................................................... 470mW *Static-sensitive device. Unused devices should be stored in conductive material. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. ELECTRICAL CHARACTERISTICS: VS = ±5V, TA = +25°C, unless otherwise indicated. Symbol Parameter VOS TCVOS Input Offset Voltage Average Temperature Coefficient of Input Offset Voltage Average Input Bias Current Average Input Offset Current Input Voltage Noise Common-Mode Rejection Ratio Common-Mode Voltage Range Open-Loop Voltage Gain Output Voltage Swing Closed Loop Bandwidth Slew Rate Power Supply Rejection Ratio Operating Supply Voltage Range Quiescent Supply Current Test Conditions TA = +25°C 0°C ≤ TA ≤ +70°C –25°C ≤ TA ≤ +85°C (Note 1) TA = +25°C 0°C ≤ TA ≤ +70°C –25°C ≤ TA ≤ +85°C TA = +25°C TA = +85°C 0.1 to 1 Hz, RS ≤ 100Ω 0.1 to 10 Hz, RS ≤ 100Ω VSS ≤ VCM ≤ VDD – 2.2 Min — — — — — — — — — — 110 VSS TC911A Typ 5 0.05 0.05 — — — 5 — 0.65 11 116 — 120 — 1.5 2.5 — — — 350 Max 15 0.15 0.15 70 3 4 20 1 — — — VDD – 2 — VDD – 0.9 — — — ±8 16 600 Min — — — — — — — — — — 105 VSS 110 VSS + 0 .3 — — 105 ±3.3 6.5 — TC911B Typ 15 0.1 0.1 — — — 10 — 0.65 11 110 — 120 — 1.5 2.5 — — — — Max 30 0.25 0.25 120 4 6 40 1 — — — VDD –2 — VDD – 0.9 — — — ±8 16 800 Unit µV µV/°C µV/°C pA nA nA pA nA µVP-P µVP-P dB V dB V MHz V/µsec dB V V µA IB IOS eN CMRR CMVR AOL VOUT BW SR PSRR VS IS RL = 10 kΩ, VOUT = ±4V 115 RL = 10 kΩ VSS + 0 .3 Closed Loop Gain = +1 — RL = 10 kΩ, CL = 50pF ±3.3V to ±5.5V Split Supply Single Supply VS = ±5V — 112 ±3.3 6.5 — NOTES: 1. Characterized; not 100% tested. 2 © 2001 Microchip Technology Inc. DS21481A Monolithic Auto-Zeroed Operational Amplifers TC911A TC911B TYPICAL CHARACTERISTICS Supply Current vs. ± Supply Voltage 700 600 TA = +25°C 450 Supply Current vs. Temperature VS = ±5V 35 Input Offset Voltage vs. Common-Mode Voltage VS = ±5V SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 400 INPUT OFFSET VOLTAGE (µV) 30 25 20 15 10 5 0 TA = +25°C 500 400 300 200 100 0 2 3 4 5 6 7 ± SUPPLY VOLTAGE (V) 8 350 300 250 200 –100 –50 0 50 100 AMBIENT TEMPERATURE (°C) 150 –6 –5 –4 –3 –2 –1 0 1 2 3 4 INPUT COMMON-MODE VOLTAGE (V) Gain and Phase vs. Frequency 50 40 PHASE GAIN VS = ±5V TA = +25°C RL = 10 kΩ 225 180 135 Large Signal Output Switching Waveform RL = 10 kΩ TA = +25°C 5.8 5.0 Output Voltage Swing vs. Load Resistance TA = +25°C VS = ±5V CLOSED-LOOP GAIN (dB) PHASE (deg) 20 10 0 90 45 0 OUTPUT VERTICAL SCALE = 1 V/DIV 0V ± OUTPUT VOLTAGE (V) 30 INPUT VERTICAL SCALE = 2 V/DIV –SWING 4.2 3.4 2.6 1.8 1.0 100 +SWING –10 –20 –45 –90 –135 100k 1M FREQUENCY (Hz) –180 10M HORIZONTAL SCALE = 2 µs/DIV –30 –40 10k 1k 10k 100k 1M LOAD RESISTANCE (Ω) © 2001 Microchip Technology Inc. DS21481A 3 Monolithic Auto-Zeroed Operational Amplifers TC911A TC911/B Pin Compatibility The CMOS TC911 is pin compatible with the industry standard ICL7650 chopper-stabilized amplifier. The ICL7650 must use external 0.1µF capacitors connected at pins 1 and 8. With the TC911, external offset voltage error canceling capacitors are not required. On the TC911 pins 1, 8 and 5 are not connected internally. The ICL7650 uses pin 5 as an optional output clamp connection. External chopper capacitors and clamp connections are not necessary with the TC911. External circuits connected to pins 1, 8 and 5 will have no effect. The TC911 can be quickly evaluated in existing ICL7650 designs. Since external capacitors are not required, system part count, assembly time, and total system cost are reduced. Reliability is increased and PC board layout eased by having the error storage capacitors integrated on the TC911 chip. The TC911 pinout matches many existing op-amps: 741, LM101, LM108, OP05–OP08, OP-20, OP-21, ICL7650 and ICL7652. In many applications operating from +5V supplies the TC911 offers superior electrical performance and can be a functional pin-compatible replacement. Offset voltage correction potentiometers, compensation capacitors, and chopper-stabilization capacitors can be removed when retrofitting existing equipment designs. (Seebeck voltage) can be measured. Junction temperature and metal type determine the magnitude. Typical values are 0.1µV/°C to 10µV/°C. Thermal-induced voltages can be many times larger than the TC911 offset voltage drift. Unless unwanted thermocouple potentials can be controlled, system performance will be less than optimum. Unwanted thermocouple junctions are created when leads are soldered or sockets/connectors are used. Low thermo-electric coefficient solder can reduce errors. A 60% Sn/36% Pb solder has 1/10 the thermal voltage of common 64% Sn/36% Pb solder at a copper junction. The number and type of dissimilar metallic junctions in the input circuit loop should be balanced. If the junctions are kept at the same temperature, their summation will add to zero-canceling errors (Figure 1). Shielding precision analog circuits from air currents — especially those caused by power dissipating components and fans — will minimize temperature gradients and thermocouple-induced errors. Avoiding Latch-Up Junction-isolated CMOS circuits inherently contain a parasitic p-n-p-n transistor circuit. Voltages exceeding the supplies by 0.3V should not be applied to the device pins. Larger voltages can turn the p-n-p-n device on, causing excessive device power supply current and excessive power dissipation. TC911 power supplies should be established at the same time or before input signals are applied. If this is not possible input current should be limited to 0.1mA to avoid triggering the p-n-p-n structure. Thermocouple Errors Heating one joint of a loop made from two different metallic wires causes current flow. This is known as the Seebeck effect. By breaking the loop, an open circuit voltage J3 = J4 J2 = J5 NO TEMPERATURE DIFFERENTIAL AND SAME METALLIC CONNECTION J1 = J6 J2 J1 J3 Overload Recovery PACKAGE PIN The TC911 recovers quickly from the output saturation. Typical recovery time from positive output saturation is 20msec. Negative output saturation recovery time is typically 5msec. J4 J5 J2 V2 J6 + – J3 V3 + – + J1 V1 – VT = V1 + V2 + V3 – V4 – V5 – V6 = 0 + J4 V 4 – VT = 0 + V5 – J5 + V6 – J6 Figure 1. Unwanted Thermocouple Errors Eliminated by Reducing Thermal Gradients and Balancing Junctions 4 © 2001 Microchip Technology Inc. DS21481A Monolithic Auto-Zeroed Operational Amplifers TC911A TC911B TYPICAL APPLICATIONS 10-Volt Precision Reference +9V TC911 REF02 ADJ R 2 Thermometer Circuit 18 kΩ +15V TC911 3+ 2 – 7 6 4 0.1 µF 3.6 kΩ VOUT = 10V TEMP OUT VREF R 1 – + R3 VOUT 6.4V 6.4 kΩ V OUT = VTEMP 1 + R2 dV OUT dT K=1+ [( R3 + R1 R3X R1 )] [ dT R2 – VREF R1 ] = [( 1 + R2 R2 R +R 3 1 R3X R1 )] d (VTEMP ) ≈ K (2.1 mV/°C) R3X R 1 Programmable Gain Amplifier With Input Multiplexer +5V –5V GND +5V –5V IN1 IN2 IN3 IN4 IC1b IC1b + – +5V –5V TC911 VOUT X1 X 10 18 k Ω X 100 99 k Ω X 1000 999 kΩ A1 A2 A3 A4 WR INPUT CHANNEL SELECT 68HC11 GAIN SELECT WR LATCH A1 A2 A3 A4 GND 2 kΩ 1 kΩ 1 kΩ IC1a, b, = Quad Analog Switch © 2001 Microchip Technology Inc. DS21481A 5 Monolithic Auto-Zeroed Operational Amplifers TC911A TC911/B PACKAGE DIMENSIONS PIN 1 .260 (6.60) .240 (6.10) .045 (1.14) .030 (0.76) .400 (10.16) .348 (8.84) .200 (5.08) .140 (3.56) .150 (3.81) .115 (2.92) .070 (1.78) .040 (1.02) .310 (7.87) .290 (7.37) .040 (1.02) .020 (0.51) .015 (0.38) .008 (0.20) .400 (10.16) .310 (7.87) 3° MIN. .110 (2.79) .090 (2.29) .022 (0.56) .015 (0.38) 8-Pin SOIC (Narrow) PIN 1 .157 (3.99) .150 (3.81) .244 (6.20) .228 (5.79) .050 (1.27) TYP. .197 (5.00) .189 (4.80) .069 (1.75) .053 (1.35) .020 (0.51) .010 (0.25) .013 (0.33) .004 (0.10) 8° MAX. .050 (1.27) .016 (0.40) .010 (0.25) .007 (0.18) Dimensions: inches (mm) 6 © 2001 Microchip Technology Inc. DS21481A Monolithic Auto-Zeroed Operational Amplifers TC911A TC911B WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com New York 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 ASIA/PACIFIC (continued) Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Rocky Mountain 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 ASIA/PACIFIC China - Beijing Microchip Technology Beijing Office Unit 915 New China Hong Kong Manhattan Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Austin Analog Product Sales 8303 MoPac Expressway North Suite A-201 Austin, TX 78759 Tel: 512-345-2030 Fax: 512-345-6085 EUROPE Australia Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 China - Shanghai Microchip Technology Shanghai Office Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Denmark Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 Boston Analog Product Sales Unit A-8-1 Millbrook Tarry Condominium 97 Lowell Road Concord, MA 01742 Tel: 978-371-6400 Fax: 978-371-0050 France Arizona Microchip Technology SARL Parc díActivite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Hong Kong Microchip Asia Pacific RM 2101, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 India Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, OíShaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Germany Arizona Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Dayton Two Prestige Place, Suite 130 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Germany Analog Product Sales Lochhamer Strasse 13 D-82152 Martinsried, Germany Tel: 49-89-895650-0 Fax: 49-89-895650-22 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Japan Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Italy Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934 United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 Printed on recycled paper. 01/09/01 Mountain View Analog Product Sales 1300 Terra Bella Avenue Mountain View, CA 94043-1836 Tel: 650-968-9241 Fax: 650-967-1590 All rights reserved. © 2001 Microchip Technology Incorporated. Printed in the USA. 1/01 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchipís products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. © 2001 Microchip Technology Inc. DS21481A 7