TC962EPA

M Features • • • • • • • • TC962 General Description The TC962 is an advanced version of the industry standard TC7662 high voltage DC-to-DC converter. Using improved design techniques and CMOS construction, the TC962 can source as much as 80mA versus the 7662’s 20mA capability. As an inverter, the TC962 can put out voltages as high as 18V and as low as 3V without the need for external diodes. The output impedance of the device is a low 28Ω (with the proper capacitors), voltage conversion efficiency is 99.9%, and power conversion efficiency is 97%. The low voltage terminal (pin 6) required in some TC7662 applications has been eliminated. Grounding this terminal will double the oscillator frequency from 12kHz to 24kHz. This will allow the use of smaller capacitors for the same output current and ripple, in most applications. Only two external capacitors are required for inverter applications. In the event an external clock is needed to drive the TC962 (such as paralleling), driving this pin directly will cause the internal oscillator to sync to the external clock. Pin 1, which is used as a test pin on the 7662, is a voltage reference zener on the TC962. This zener (6.4V at 5mA) has a dynamic impedance of 12Ω and is intended for use where the TC962 is supplying current to external regulator circuitry and a reference is needed for the regulator circuit. (See Section 3.0 Applications Information). The TC962 is compatible with the LTC1044, SI7661 and ICL7662. It should be used in designs that require greater power and/or less input to output voltage drop. It offers superior performance over the ICL7660S. High Current Charge Pump DC-to-DC Converter Pin Compatible With TC7662/ICL7662/SI7661 High Output Current 80mA No External Diodes Required Wide Operating Range 3V to 18V Low Output Impedance 28Ω Typ. No Low Voltage Terminal Required Application Zener On-Chip OSC Frequency Doubling Pin Option for Smaller Output Capacitors Applications • • • • Laptop Computers Disk Drives Process Instrumentation µP-Based Controllers Device Selection Table Part Number TC962COE TC962CPA TC962EPA TC962IJA TC962MJA Package 16-Pin SOIC Wide 8-Pin Plastic DIP 8-Pin Plastic DIP 8-Pin CERDIP 8-Pin CERDIP Operating Temp. Range 0°C to +70°C 0°C to +70°C -40°C to +85°C -25°C to +85°C -55°C to +125°C Package Type 16-Pin SOIC Wide 8-Pin DIP 8-Pin CERDIP Zener 8 VDD Cathode 1 • C+ 2 TC962CPA 7 COSC 6 FREQ x 2 GND 3 TC962IJA –4 C TC962MJA 5 VOUT Zener Cathode 1 NC 2 C+ 3 NC 4 GND 5 NC 6 C– 7 NC 8 16 VDD 15 NC 14 COSC 13 NC TC962EPA TC962COE 12 FREQ x 2 11 NC 10 VOUT 9 NC  2002 Microchip Technology Inc. DS21484B-page 1 TC962 Functional Block Diagram 8 FREQ x 2 – OSC/C Timing 6 7 Level Shift P SW1 2 CAP + I I VDD TC962 Q + – F/F C Q Comparator with Hysteresis Level Shift N SW4 + CP External 3 GND Zener Cathode 1 6.4V VREF + Level Shift OUT N SW2 4 CAP – CR EXT RL Level Shift N SW3 5 VOUT DS21484B-page 2  2002 Microchip Technology Inc. TC962 1.0 ELECTRICAL CHARACTERISTICS *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings* Supply Voltage (VDD to GND) ..............................+18V Input Voltage Any Pin ......................... (VDD +0.3) to (VSS -0.3) (Note 1) Current Into Any Pin............................................ 10mA ESD Protection ................................................ ±2000V Output Short Circuit ........... Continuous (at 5.5V Input) Package Power Dissipation (TA ≤ 70°C) SOIC ....................................................... 760 mW PDIP........................................................ 730 mW CERDIP .................................................. 800 mW Package Thermal Resistance CERDIP, RθJ-A ......................................... 90°C/W PDIP, RθJ-A ............................................ 140°C/W Operating Temperature Range CPA, COE ....................................... 0°C to +70°C IJA ................................................ -25°C to +85°C EPA .............................................. -40°C to +85°C MJA ............................................ -55°C to +125°C Storage Temperature Range ............. -65°C to +150°C TC962 ELECTRICAL SPECIFICATIONS Electrical Characteristics: VDD = 15V, TA = 25°C (See Figure 3-1) unless otherwise noted. Symbol VDD IS Parameter Supply Voltage Supply Current VDD = 15V Min 3 — — — — — — — — — — — — 93 — 99 — 96 6.0 — Typ — — 510 560 650 190 210 210 32 35 — 12 24 97 — 99.9 — — 6.2 12 Max 18 — 700 — — — — — 37 40 50 — — — — — — — 6.4 — Units V µA Test Conditions RL = ∞ TA = +25°C 0 ≤ TA ≤ +70°C -55°C ≤ TA ≤ +125°C TA = +25°C 0 ≤ TA ≤ +70°C -55°C ≤ TA ≤ +125°C IL = 20mA, VDD = 15V IL = 80mA, VDD = 15V IL = 3mA, VDD = 5V Pin 6 Open Pin 6 GND R L = 2 kΩ RL = ∞ Over temperature range IZ = 5mA IL = 2.5mA to 7.5mA VDD = 5V RO Output Source Resistance Oscillator Frequency Power Efficiency Voltage Efficiency Ω FOSC PEFF VDEF kHz % % VZ ZZT Note 1: Zener Voltage Zener Impedance V Ω Connecting any input terminal to voltages greater than V+ or less than GND may cause destructive latch-up. It is recommended that no inputs from sources operating from external supplies be applied prior to "power up" of the TC962.  2002 Microchip Technology Inc. DS21484B-page 3 TC962 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: Pin No. (8-Pin DIP) (8-Pin CERDIP) 1 2 3 4 5 6 7 8 PIN FUNCTION TABLE Symbol Zener Cathode C+ GND CVOUT FREQ x 2 COSC VDD Cathode of internal zener diode. Positive side of external CP capacitor (pump cap). Ground terminal. Negative side of external CP capacitor (pump cap). Output voltage. If grounded, frequency doubles. Capacitor to GND will decrease frequency. Input voltage. Description Pin No. (16-Pin SOIC) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol Zener Cathode NC C + Description Cathode of internal zener diode. No connect. Positive side of external CP capacitor (pump cap). No connect. Ground terminal. No connect. Negative side of external CP capacitor (pump cap). No connect. No connect. Output voltage. No connect. If grounded, frequency doubles. No connect. Capacitor to GND will decrease frequency. No connect. Input voltage. NC GND NC C - NC NC VOUT NC FREQ x 2 NC COSC NC VDD DS21484B-page 4  2002 Microchip Technology Inc. TC962 3.0 3.1 APPLICATIONS INFORMATION Theory of Operation internal to the TC962. Grounding pin 6 will turn on a current source and double the frequency. This will double the charge current going into the internal capacitor, as well as any capacitor added to pin 7. A zener diode has been added to the TC962 for use as a reference in building external regulators. This zener runs from pin 1 to ground. The TC962 is a capacitive pump (sometimes called a switched capacitor circuit), where four MOSFET switches control the charge and discharge of a capacitor. The functional block diagram shows how the switching action works. SW1 and SW2 are turned on simultaneously, charging CP to the supply voltage, VIN. This assumes that the on resistance of the MOSFETs in series with the capacitor results in a charging time (3 time constants) that is less than the on time provided by the oscillator frequency as shown: 3 (RDS(ON) CP) < CP/(0.5 fOSC) In the next cycle, SW1 and SW2 are turned off and after a very short interval of all switches being off (this prevents large currents from occurring due to cross conduction), SW3 and SW4 are turned on. The charge in CP is then transferred to CR, but with the polarity inverted. In this way, a negative voltage is now derived. An oscillator supplies pulses to a flip-flop that is then fed to a set of level shifters. These level shifters then drive each set of switches at one-half the oscillator frequency. The oscillator has two pins that control the frequency of oscillation. Pin 7 can have a capacitor added that is returned to ground. This will lower the frequency of the oscillator by adding capacitance to the timing capacitor 3.2 Latch Up All CMOS structures contain a parasitic SCR. Care must be taken to prevent any input from going above or below the supply rail, or latch up will occur. The result of latch up is an effective short between VDD and VSS. Unless the power supply input has a current limit, this latch up phenomena will result in damage to the device. (See AN763 Latch-up Protection of CMOS ICs.) FIGURE 3-1: 690 TEST CIRCUIT IS NC + 10µF 1 2 CP 3 4 8 7 IL COSC 5 RL V+ (+5V) TC962 VOUT (–5V) CR + 10µF FIGURE 3-2: TYPICAL APPLICATIONS Split V+ In Half V+ 1 VD1 VD2 VOUT = –V + C R1 10µF CR + 10µF + VOUT = 2V + –2V 10µF CP D Combined Negative Converter and Positive Multiplier V+ 1 2 + 10µF 3 CP2 4 CP1 + 8 7 8 7 2 + 10µF 3 4 TC962 6 5 + TC962 6 5 VOUT = V+ 2 Lowering Output Resistance by Paralleling Devices V+ Positive Voltage Multiplier V+ 1 2 CP1 + 10µF 3 4 8 7 + 10µF 1 2 CP2 3 4 8 7 1 2 3 4 VOUT CR + 10µF 8 7 VD1 VD2 CP + 10µF CP + VOUT = 2V +–2V 10µF TC962 6 5 TC962 6 5 TC962 6 5 D  2002 Microchip Technology Inc. DS21484B-page 5 TC962 4.0 Note: TYPICAL CHARACTERISTICS The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Circuit of Figure 3-1, CP = CR = 10µF, CPESR ≈ CRESR ≈ 1Ω. Supply Current vs. Temperature 700 600 10k Oscillator Frequency vs. C OSC 20 TA = +25°C 18 Frequency vs. Temperature COSC = FREQ x 2 = OPEN SUPPLY CURRENT (µA) 400 300 200 100 0 -60 -40 -20 V + = 15V FREQUENCY (Hz) 1k FREQUENCY (kHz) 1 10 100 1000 10,000 500 16 14 12 10 8 100 V + = 15V 10 0 20 40 60 80 100 120 140 TEMPERATURE (°C) CAPACITANCE (pF) 6 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) Output Resistance vs. Temperature 80 OUTPUT RESISTANCE ( Ω) 70 60 50 40 30 20 10 -60 -40 -20 V+ = 15V IL = 20mA 10 0 4.5 V+ = 5V IL = 3mA 50 Current vs. Zener Voltage POWER CONVERSION EFFICIENCY (%) TA = +25°C Power Conversion Efficiency vs. I LOAD 100 90 80 70 60 50 40 30 20 10 0 8 16 24 32 40 48 56 64 72 80 SUPPLY CURRENT EFFICIENCY TA = +25°C 150 SUPPLY CURRENT (mA) 135 120 105 90 75 60 45 30 15 0 LOAD CURRENT (mA) CURRENT (mA) 40 30 20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4.0 5.5 6.0 6.5 7.0 ZENER VOLTAGE (V) Output Resistance vs. Input Voltage 110 100 TA = +25°C OUTPUT RESISTANCE (Ω) 90 80 70 60 50 40 30 20 10 0 2 4 6 8 10 12 14 16 18 INPUT VOLTAGE (V) 20 3mA 20mA DS21484B-page 6  2002 Microchip Technology Inc. TC962 5.0 5.1 PACKAGING INFORMATION Package Marking Information Package marking data not available at this time. 5.2 Package Dimensions 8-Pin CDIP (Narrow) .110 (2.79) .090 (2.29) PIN 1 .300 (7.62) .230 (5.84) .055 (1.40) MAX. .400 (10.16) .370 (9.40) .200 (5.08) .160 (4.06) .200 (5.08) .125 (3.18) .020 (0.51) MIN. .320 (8.13) .290 (7.37) .040 (1.02) .020 (0.51) .015 (0.38) .008 (0.20) .400 (10.16) .320 (8.13) .065 (1.65) .020 (0.51) .045 (1.14) .016 (0.41) Dimensions: inches (mm) .150 (3.81) MIN. 3° MIN. 8-Pin Plastic DIP PIN 1 .260 (6.60) .240 (6.10) .045 (1.14) .030 (0.76) .400 (10.16) .348 (8.84) .200 (5.08) .140 (3.56) .150 (3.81) .115 (2.92) .070 (1.78) .040 (1.02) .310 (7.87) .290 (7.37) .040 (1.02) .020 (0.51) .015 (0.38) .008 (0.20) .400 (10.16) .310 (7.87) 3° MIN. .110 (2.79) .090 (2.29) .022 (0.56) .015 (0.38) Dimensions: inches (mm)  2002 Microchip Technology Inc. DS21484B-page 7 TC962 Package Dimensions (Continued) 16-Pin SOIC (Wide) PIN 1 .299 (7.59) .419 (10.65) .291 (7.40) .398 (10.10) .413 (10.49) .398 (10.10) .104 (2.64) .097 (2.46) .050 (1.27) TYP. .019 (0.48) .014 (0.36) .012 (0.30) .004 (0.10) 8° MAX. .050 (1.27) .016 (0.40) Dimensions: inches (mm) .013 (0.33) .009 (0.23) DS21484B-page 8  2002 Microchip Technology Inc. TC962 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.  2002 Microchip Technology Inc. DS21484B-page9 TC962 NOTES: DS21484B-page10  2002 Microchip Technology Inc. TC962 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, microID, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified.  2002 Microchip Technology Inc. DS21484B-page 11 M WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com ASIA/PACIFIC Australia Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Japan Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Rocky Mountain 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 China - Beijing Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 China - Chengdu Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-6766200 Fax: 86-28-6766599 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 EUROPE Denmark Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 China - Shanghai Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Kokomo 2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387 France Microchip Technology SARL Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 China - Shenzhen Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086 New York 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 Germany Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Hong Kong Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 Italy Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 India Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O’Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 03/01/02 ' !%! ' DS21484B-page 12  2002 Microchip Technology Inc.