NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
2Mb SYNCBURST™
SRAM
MT58L128L18D, MT58L64L32D,
MT58L64L36D
3.3V VDD, 3.3V I/O, Pipelined, Double-Cycle
Deselect
FEATURES
• Fast clock and OE# access times
• Single +3.3V +0.3V/-0.165V power supply (VDD)
• Separate +3.3V isolated output buffer supply
(VDDQ)
• SNOOZE MODE for reduced-power standby
• Common data inputs and data outputs
• Individual BYTE WRITE control and GLOBAL
WRITE
• Three chip enables for simple depth expansion and
address pipelining
• Clock-controlled and registered addresses, data
I/Os and control signals
• Internally self-timed WRITE cycle
• Burst control pin (interleaved or linear burst)
• Automatic power-down
• 100-pin TQFP package
• Low capacitive bus loading
• x18, x32, and x36 options available
OPTIONS
100-Pin TQFP*
*JEDEC-standard MS-026 BHA (LQFP).
controlled by a positive-edge-triggered single clock
input (CLK). The synchronous inputs include all addresses, all data inputs, active LOW chip enable (CE#),
two additional chip enables for easy depth expansion
(CE2, CE2#), burst control inputs (ADSC#, ADSP#,
ADV#), byte write enables (BWx#) and global write
(GW#).
Asynchronous inputs include the output enable
(OE#), clock (CLK) and snooze enable (ZZ). There is also
a burst mode pin (MODE) that selects between interleaved and linear burst modes. The data-out (Q), enabled by OE#, is also asynchronous. WRITE cycles can
be from one to two bytes wide (x18) or from one to four
bytes wide (x32/x36), as controlled by the write control
inputs.
Burst operation can be initiated with either address
status processor (ADSP#) or address status controller
(ADSC#) input pins. Subsequent burst addresses can be
internally generated as controlled by the burst advance
pin (ADV#).
Address and write control are registered on-chip to
simplify WRITE cycles. This allows self-timed WRITE
cycles. Individual byte enables allow individual bytes
to be written. During WRITE cycles on the x18 device,
BWa# controls DQa pins and DQPa; BWb# controls
DQb pins and DQPb. During WRITE cycles on the x32
and x36 devices, BWa# controls DQa pins and DQPa;
BWb# controls DQb pins and DQPb; BWc# controls
MARKING
• Timing (Access/Cycle/MHz)
3.5ns/6ns/166 MHz
4.0ns/7.5ns/133 MHz
5ns/10ns/100 MHz
• Configurations
128K x 18
64K x 32
64K x 36
-6
-7.5
-10
MT58L128L18D
MT58L64L32D
MT58L64L36D
• Packages
100-pin TQFP
T
• Operating Temperature Range
Commercial (0°C to +70°C)
None
Part Number Example:
MT58L128L18DT-10
GENERAL DESCRIPTION
The Micron® SyncBurst™ SRAM family employs
high- speed, low-power CMOS designs that are fabricated using an advanced CMOS process.
Micron’s 2Mb SyncBurst SRAMs integrate a 128K x
18, 64K x 32, or 64K x 36 SRAM core with advanced
synchronous peripheral circuitry and a 2-bit burst
counter. All synchronous inputs pass through registers
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
1
©2002, Micron Technology, Inc.
PRODUCTS AND SPECIFICATIONS DISCUSSED HEREIN ARE SUBJECT TO CHANGE BY MICRON WITHOUT NOTICE.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
FUNCTIONAL BLOCK DIAGRAM
128K x 18
17
SA0, SA1, SA
15
17
ADDRESS
REGISTER
2
MODE
SA0-SA1
SA1'
BINARY Q1
COUNTER AND
LOGIC
CLR
Q0
ADV#
CLK
17
SA0'
ADSC#
ADSP#
BYTE “b”
WRITE REGISTER
BWb#
9
9
BYTE “a”
WRITE REGISTER
BWa#
BYTE “b”
WRITE DRIVER
BYTE “a”
WRITE DRIVER
9
128K x 9 x 2
MEMORY
ARRAY
18
OUTPUT 18
REGISTERS
SENSE 18
AMPS
OUTPUT
BUFFERS
18
E
9
DQs
DQPa
DQPb
BWE#
GW#
INPUT
REGISTERS
18
ENABLE
REGISTER
CE#
CE2
CE2#
PIPELINED
ENABLE
2
OE#
FUNCTIONAL BLOCK DIAGRAM
64K x 32/36
16
ADDRESS
REGISTER
SA0, SA1, SA
14
16
16
SA0-SA1
MODE
SA1'
Q1
BINARY
COUNTER
SA0'
CLR
Q0
ADV#
CLK
ADSC#
ADSP#
BWd#
BYTE “d”
WRITE REGISTER
9
BYTE “d”
WRITE DRIVER
9
BWc#
BYTE “c”
WRITE REGISTER
9
BYTE “c”
WRITE DRIVER
9
BWb#
BWa#
BWE#
GW#
CE#
CE2
CE2#
OE#
64K x 9 x 4
(x36)
BYTE “b”
WRITE REGISTER
9
BYTE “b”
WRITE DRIVER
9
BYTE “a”
WRITE REGISTER
9
BYTE “a”
WRITE DRIVER
9
ENABLE
REGISTER
64K x 8 x 4
(x32)
36
SENSE
AMPS
OUTPUT
REGISTERS 36
36
MEMORY
ARRAY
OUTPUT
BUFFERS
E
36
DQs
DQPa
DQPb
DQPb
DQPb
INPUT
REGISTERS
36
PIPELINED
ENABLE
4
NOTE: Functional Block Diagrams illustrate simplified device operation. See truth table, pin descriptions and timing diagrams for
detailed information.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
2
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
GENERAL DESCRIPTION (continued)
DQc pins and DQPc; BWd# controls DQd pins and
DQPd. GW# LOW causes all bytes to be written. Parity
pins are only available on the x18 and x36 versions.
The device incorporates an additional pipelined
enable register which delays turning off the output
buffer an additional cycle when a deselect is executed.
This feature allows depth expansion without penalizing system performance.
Micron’s 2Mb SyncBurst SRAMs operate from a
+3.3V VDD power supply, and all inputs and outputs are
TTL-compatible. The device is ideally suited for
Pentium® and PowerPC pipelined systems and systems
that benefit from a very wide, high-speed data bus. The
device is also ideal in generic 16-, 18-, 32-, 36-, 64-, and
72-bit-wide applications.
Please refer to Micron’s Web site (www.micron.com/
sramds) for the latest data sheet.
TQFP PIN ASSIGNMENT TABLE
PIN #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
x18
NC
NC
NC
x32/x36
NC/DQPc**
DQc
DQc
VDDQ
VSS
NC
DQc
NC
DQc
DQb
DQc
DQb
DQc
VSS
VDDQ
DQb
DQc
DQb
DQc
VDD
VDD
NC
VSS
DQb
DQd
DQb
DQd
VDDQ
VSS
DQb
DQd
DQb
DQd
DQPb
DQd
NC
DQd
PIN #
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
x18
x32/x36
VSS
VDDQ
NC
DQd
NC
DQd
NC
NC/DQPd**
MODE
SA
SA
SA
SA
SA1
SA0
DNU
DNU
VSS
VDD
DNU
DNU
SA
SA
SA
SA
SA
SA
NC/SA*
PIN #
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
x18
NC
NC
NC
x32/x36
NC/DQPa**
DQa
DQa
VDDQ
VSS
NC
DQa
NC
DQa
DQa
DQa
VSS
VDDQ
DQa
DQa
ZZ
VDD
NC
VSS
DQa
DQb
DQa
DQb
VDDQ
VSS
DQa
DQb
DQa
DQb
DQPa
DQb
NC
DQb
PIN #
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
x18
NC
NC
SA
NC
NC
x32/x36
VSS
VDDQ
DQb
DQb
NC/DQPb**
SA
SA
ADV#
ADSP#
ADSC#
OE#
BWE#
GW#
CLK
VSS
VDD
CE2#
BWa#
BWb#
BWc#
BWd#
CE2
CE#
SA
SA
*Pin 50 is reserved for address expansion.
**No Connect (NC) is used on the x32 version. Parity (DQPx) is used on the x36 version.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
3
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
SA
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
PIN ASSIGNMENT (Top View)
100-Pin TQFP
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
50
81
49
82
48
83
47
84
46
85
45
86
44
87
43
88
42
89
41
90
40
91
39
92
38
93
37
94
36
95
35
96
34
97
33
98
32
99
31
100
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
x18
NC/SA*
SA
SA
SA
SA
SA
SA
DNU
DNU
VDD
VSS
DNU
DNU
SA0
SA1
SA
SA
SA
SA
MODE
NC
NC/DQPb**
NC
DQb
NC
DQb
V
DDQ
VDDQ
SS
V
VSS
NC
DQb
NC
DQb
DQb
DQb
DQb
DQb
VSS
VSS
VDDQ
VDDQ
DQb
DQb
DQb
DQb
VDD
VSS
VDD
NC
NC
VDD
ZZ
VSS
DQa
DQb
DQa
DQb
VDDQ
VDDQ
VSS
VSS
DQa
DQb
DQa
DQb
DQa
DQPb
DQa
NC
VSS
VSS
VDDQ
VDDQ
DQa
NC
DQa
NC
NC/DQPa**
NC
SA
SA
ADV#
ADSP#
ADSC#
OE#
BWE#
GW#
CLK
VSS
VDD
CE2#
BWa#
BWb#
NC
NC
CE2
CE#
SA
SA
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
50
81
49
82
48
83
47
84
46
85
45
86
44
87
43
88
42
89
41
90
40
91
39
92
38
93
37
94
36
95
35
96
34
97
33
98
32
99
31
100
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
x32/x36
NC/SA*
SA
SA
SA
SA
SA
SA
DNU
DNU
VDD
VSS
DNU
DNU
SA0
SA1
SA
SA
SA
SA
MODE
NC/DQPc**
DQc
DQc
VDDQ
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
DQc
DQc
VDD
VDD
NC
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
NC/DQPd**
SA
SA
ADV#
ADSP#
ADSC#
OE#
BWE#
GW#
CLK
VSS
VDD
CE2#
BWa#
BWb#
BWc#
BWd#
CE2
CE#
SA
SA
*Pin 50 is reserved for address expansion.
**No Connect (NC) is used on the x32 version. Parity (DQPx) is used on the x36 version.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
TQFP PIN DESCRIPTIONS
x18
x32/x36
37
37
36
36
32-35, 44-49, 32-35, 44-49,
80-82, 99,
81, 82, 99,
100
100
SYMBOL
TYPE
SA0
SA1
SA
Input
Synchronous Address Inputs: These inputs are registered and must
meet the setup and hold times around the rising edge of CLK.
DESCRIPTION
93
94
–
–
93
94
95
96
BWa#
BWb#
BWc#
BWd#
Input
Synchronous Byte Write Enables: These active LOW inputs allow
individual bytes to be written and must meet the setup and hold
times around the rising edge of CLK. A byte write enable is LOW
for a WRITE cycle and HIGH for a READ cycle. For the x18 version,
BWa# controls DQa pins and DQPa; BWb# controls DQb pins and
DQPb. For the x32 and x36 versions, BWa# controls DQa pins and
DQPa; BWb# controls DQb pins and DQPb; BWc# controls DQc pins
and DQPc; BWd# controls DQd pins and DQPd. Parity is only
available on the x18 and x36 versions.
87
87
BWE#
Input
Byte Write Enable: This active LOW input permits BYTE WRITE
operations and must meet the setup and hold times around the
rising edge of CLK.
88
88
GW#
Input
Global Write: This active LOW input allows a full 18-, 32-, or 36-bit
WRITE to occur independent of the BWE# and BWx# lines and must
meet the setup and hold times around the rising edge of CLK.
89
89
CLK
Input
Clock: This signal registers the address, data, chip enable, byte
write enables and burst control inputs on its rising edge. All
synchronous inputs must meet setup and hold times around the
clock’s rising edge.
98
98
CE#
Input
Synchronous Chip Enable: This active LOW input is used to enable
the device and conditions the internal use of ADSP#. CE# is sampled
only when a new external address is loaded.
92
92
CE2#
Input
Synchronous Chip Enable: This active LOW input is used to enable
the device and is sampled only when a new external address is
loaded.
64
64
ZZ
Input
Snooze Enable: This active HIGH, asynchronous input causes the
device to enter a low-power standby mode in which all data in the
memory array is retained. When ZZ is active, all other inputs are
ignored.
97
97
CE2
Input
Synchronous Chip Enable: This active HIGH input is used to enable
the device and is sampled only when a new external address is
loaded.
86
86
OE#
Input
Output Enable: This active LOW, asynchronous input enables the
data I/O output drivers.
83
83
ADV#
Input
Synchronous Address Advance: This active LOW input is used to
advance the internal burst counter, controlling burst access after
the external address is loaded. A HIGH on this pin effectively causes
wait states to be generated (no address advance). To ensure use of
correct address during a WRITE cycle, ADV# must be HIGH at the
rising edge of the first clock after an ADSP# cycle is initiated.
(continued on next page)
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
5
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
TQFP PIN DESCRIPTIONS (continued)
x18
x32/x36
SYMBOL
TYPE
DESCRIPTION
84
84
ADSP#
Input
Synchronous Address Status Processor: This active LOW input
interrupts any ongoing burst, causing a new external address to be
registered. A READ is performed using the new address,
independent of the byte write enables and ADSC#, but dependent
upon CE#, CE2, and CE2#. ADSP# is ignored if CE# is HIGH. Powerdown state is entered if CE2 is LOW or CE2# is HIGH.
85
85
ADSC#
Input
Synchronous Address Status Controller: This active LOW input
interrupts any ongoing burst, causing a new external address to be
registered. A READ or WRITE is performed using the new address if
CE# is LOW. ADSC# is also used to place the chip into power-down
state when CE# is HIGH.
31
31
MODE
Input
Mode: This input selects the burst sequence. A LOW on this pin
selects “linear burst.” NC or HIGH on this pin selects “interleaved
burst.” Do not alter input state while device is operating.
(a) 58, 59,
(a) 52, 53,
62, 63, 68, 69, 56-59, 62, 63
72, 73
(b) 8, 9, 12,
(b) 68, 69,
13, 18, 19,
72-75, 78, 79
22, 23
(c) 2, 3, 6-9,
12, 13
(d) 18, 19,
22-25, 28, 29
74
24
–
–
51
80
1
30
DQa
DQb
Input/ SRAM Data I/Os: For the x18 version, Byte “a” is DQa pins; Byte “b”
Output is DQb pins. For the x32 and x36 versions, Byte “a” is DQa pins;
Byte “b” is DQb pins; Byte “c” is DQc pins; Byte “d” is DQd pins.
Input data must meet setup and hold times around the rising edge
of CLK.
DQc
DQd
NC/DQPa
NC/DQPb
NC/DQPc
NC/DQPd
NC/
I/O
No Connect/Parity Data I/Os: On the x32 version, these pins are No
Connect (NC). On the x18 version, Byte “a” parity is DQPa; Byte “b”
parity is DQPb. On the x36 version, Byte “a” parity is DQPa; Byte
“b” parity is DQPb; Byte “c” parity is DQPc; Byte “d” parity is DQPd.
Supply Power Supply: See DC Electrical Characteristics and Operating
Conditions for range.
14, 15, 41, 65, 14, 15, 41, 65,
91
91
VDD
4, 11, 20, 27, 4, 11, 20, 27,
54, 61, 70, 77 54, 61, 70, 77
VDDQ
5, 10, 17, 21, 5, 10, 17, 21,
26, 40, 55, 60, 26, 40, 55, 60,
67, 71, 76, 90 67, 71, 76, 90
VSS
38, 39, 42, 43 38, 39, 42, 43
DNU
–
Do Not Use: These signals may either be unconnected or wired to
GND to improve package heat dissipation.
Supply Isolated Output Buffer Supply: See DC Electrical Characteristics and
Operating Conditions for range.
Supply Ground: GND.
1-3, 6, 7, 16,
25, 28-30,
51-53, 56, 57,
66, 75, 78, 79,
95, 96
16, 66
NC
–
No Connect: These signals are not internally connected and may be
connected to ground to improve package heat dissipation.
50
50
NC/SA
–
No Connect: This pin is reserved for address expansion.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
6
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
INTERLEAVED BURST ADDRESS TABLE (MODE = NC OR HIGH)
FIRST ADDRESS (EXTERNAL)
SECOND ADDRESS (INTERNAL)
THIRD ADDRESS (INTERNAL)
FOURTH ADDRESS (INTERNAL)
X...X00
X...X01
X...X10
X...X11
X...X01
X...X00
X...X11
X...X10
X...X10
X...X11
X...X00
X...X01
X...X11
X...X10
X...X01
X...X00
LINEAR BURST ADDRESS TABLE (MODE = LOW)
FIRST ADDRESS (EXTERNAL)
SECOND ADDRESS (INTERNAL)
THIRD ADDRESS (INTERNAL)
FOURTH ADDRESS (INTERNAL)
X...X00
X...X01
X...X10
X...X11
X...X01
X...X10
X...X11
X...X00
X...X10
X...X11
X...X00
X...X01
X...X11
X...X00
X...X01
X...X10
Partial Truth Table For WRITE COMMANDS (x18)
FUNCTION
READ
GW#
BWE#
BWa#
BWb#
H
H
X
X
READ
H
L
H
H
WRITE Byte “a”
H
L
L
H
WRITE Byte “b”
H
L
H
L
WRITE All Bytes
H
L
L
L
WRITE All Bytes
L
X
X
X
PARTIAL TRUTH TABLE FOR WRITE COMMANDS (x32/x36)
FUNCTION
GW#
BWE#
BWa#
BWb#
BWc#
BWd#
READ
H
H
X
X
X
X
READ
H
L
H
H
H
H
WRITE Byte “a”
H
L
L
H
H
H
WRITE All Bytes
H
L
L
L
L
L
WRITE All Bytes
L
X
X
X
X
X
NOTE: Using BWE# and BWa# through BWd#, any one or more bytes may be written.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
7
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
TRUTH TABLE
OPERATION
ADDRESS
USED
Deselected Cycle, Power-Down
None
Deselected Cycle, Power-Down
None
Deselected Cycle, Power-Down
None
CE# CE2# CE2
ZZ
ADSP# ADSC# ADV# WRITE# OE#
CLK
DQ
H
L
L
X
X
H
X
L
X
L
L
L
X
L
L
L
X
X
X
X
X
X
X
X
X
X
X
L-H
L-H
L-H
High-Z
High-Z
High-Z
Deselected Cycle, Power-Down
Deselected Cycle, Power-Down
SNOOZE MODE, Power-Down
READ Cycle, Begin Burst
READ Cycle, Begin Burst
None
None
None
External
External
L
L
X
L
L
X
H
X
L
L
L
X
X
H
H
L
L
H
L
L
H
H
X
L
L
L
L
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
L
H
L-H
L-H
X
L-H
L-H
High-Z
High-Z
High-Z
Q
High-Z
WRITE Cycle, Begin Burst
READ Cycle, Begin Burst
READ Cycle, Begin Burst
READ Cycle, Continue Burst
External
External
External
Next
L
L
L
X
L
L
L
X
H
H
H
X
L
L
L
L
H
H
H
H
L
L
L
H
X
X
X
L
L
H
H
H
X
L
H
L
L-H
L-H
L-H
L-H
D
Q
High-Z
Q
READ Cycle, Continue Burst
READ Cycle, Continue Burst
Next
Next
X
H
X
X
X
X
L
L
H
X
H
H
L
L
H
H
H
L
L-H
L-H
High-Z
Q
READ Cycle, Continue Burst
WRITE Cycle, Continue Burst
WRITE Cycle, Continue Burst
Next
Next
Next
H
X
H
X
X
X
X
X
X
L
L
L
X
H
X
H
H
H
L
L
L
H
L
L
H
X
X
L-H
L-H
L-H
High-Z
D
D
READ Cycle, Suspend Burst
READ Cycle, Suspend Burst
Current
Current
X
X
X
X
X
X
L
L
H
H
H
H
H
H
H
H
L
H
L-H
L-H
Q
High-Z
READ Cycle, Suspend Burst
READ Cycle, Suspend Burst
WRITE Cycle, Suspend Burst
WRITE Cycle, Suspend Burst
Current
Current
Current
Current
H
H
X
H
X
X
X
X
X
X
X
X
L
L
L
L
X
X
H
X
H
H
H
H
H
H
H
H
H
H
L
L
L
H
X
X
L-H
L-H
L-H
L-H
Q
High-Z
D
D
NOTE: 1. X means “Don’t Care.” # means active LOW. H means logic HIGH. L means logic LOW.
2. For WRITE#, L means any one or more byte write enable signals (BWa#, BWb#, BWc# or BWd#) and BWE# are LOW or
GW# is LOW. WRITE# = H for all BWx#, BWE#, GW# HIGH.
3. BWa# enables WRITEs to DQa pins, DQPa. BWb# enables WRITEs to DQb pins, DQPb. BWc# enables WRITEs to DQc
pins, DQPc. BWd# enables WRITEs to DQd pins, DQPd. DQPa and DQPb are only available on the x18 and x36 versions.
DQPc and DQPd are only available on the x36 version.
4. All inputs except OE# and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
5. Wait states are inserted by suspending burst.
6. For a WRITE operation following a READ operation, OE# must be HIGH before the input data setup time and held
HIGH throughout the input data hold time.
7. This device contains circuitry that will ensure the outputs will be in High-Z during power-up.
8. ADSP# LOW always initiates an internal READ at the L-H edge of CLK. A WRITE is performed by setting one or more
byte write enable signals and BWE# LOW or GW# LOW for the subsequent L-H edge of CLK. Refer to WRITE timing
diagram for clarification.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
8
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
ABSOLUTE MAXIMUM RATINGS*
*Stresses greater than those listed under “Absolute
Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only, and functional
operation of the device at these or any other conditions
above those indicated in the operational sections of
this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect reliability.
**Maximum junction temperature depends upon package type, cycle time, loading, ambient temperature and
airflow. See Micron Technical Note TN-05-14 for more
information.
Voltage on VDD Supply
Relative to Vss .................................... -0.5V to +4.6V
Voltage on VDDQ Supply
Relative to Vss .................................... -0.5V to +4.6V
VIN ............................................... -0.5V to VDDQ + 0.5V
Storage Temperature (plastic) ............ -55°C to +150°C
Junction Temperature** .................................... +150°C
Short Circuit Output Current ........................... 100mA
3.3V I/O DC ELECTRICAL CHARACTERISTICS AND OPERATING CONDITIONS
(0°C ≤ TA ≤ +70°C; VDD, VDDQ = +3.3V +0.3V/-0.165V unless otherwise noted)
DESCRIPTION
CONDITIONS
Input High (Logic 1) Voltage
Input Low (Logic 0) Voltage
Input Leakage Current
Output Leakage Current
Output High Voltage
Output Low Voltage
0V ≤ VIN ≤ VDD
Output(s) disabled,
0V ≤ VIN ≤ VDD
IOH = -4.0mA
IOL = 8.0mA
Supply Voltage
Isolated Output Buffer Supply
SYMBOL
MIN
MAX
UNITS
NOTES
VIH
VIL
2.0
-0.3
VDD + 0.3
0.8
V
V
1, 2
1, 2
ILI
ILO
-1.0
-1.0
1.0
1.0
µA
µA
3
VOH
VOL
2.4
–
–
0.4
V
V
1, 4
1, 4
VDD
VDDQ
3.135
3.135
3.6
VDD
V
V
1
1, 5
NOTE: 1. All voltages referenced to VSS (GND).
2. Overshoot:
VIH ≤ +4.6V for t ≤ tKC/2 for I ≤ 20mA
Undershoot: VIL ≥ -0.7V for t ≤ tKC/2 for I ≤ 20mA
Power-up:
VIH ≤ +3.6V and VDD ≤ 3.135V for t ≤ 200ms
3. MODE pin has an internal pull-up, and input leakage = ±10µA.
4. The load used for VOH, VOL testing is shown in Figure 2. AC load current is higher than the shown DC values. AC I/O
curves are available upon request.
5. VDDQ should never exceed VDD. VDD and VDDQ can be connected together for 3.3V I/O.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
9
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
IDD OPERATING CONDITIONS AND MAXIMUM LIMITS
(0°C ≤ TA ≤ +70°C; VDD, VDDQ = +3.3V +0.3V/-0.165V unless otherwise noted)
MAX
DESCRIPTION
Power Supply
Current: Operating
Power Supply
Current: Idle
CMOS Standby
SYMBOL
TYP
-6
-7.5
-10
IDD
100
340
280
225
mA
1, 2, 3
IDD1
30
85
70
65
mA
1, 2, 3
ISB2
0.5
10
10
10
mA
2, 3
ISB3
6
25
25
25
mA
2, 3
ISB4
30
85
70
65
mA
2, 3
Device selected; VDD = MAX;
ADSC#, ADSP#, GW#, BWx#, ADV# ≥
VIH; All inputs ≤ VSS + 0.2 or ≥ VDD - 0.2;
Cycle time ≥ tKC MIN
Device deselected; VDD = MAX;
All inputs ≤ VSS + 0.2 or ≥ VDD - 0.2;
All inputs static; CLK frequency = 0
TTL Standby
Clock Running
CONDITIONS
Device selected; All inputs ≤ VIL
or ≥ VIH; Cycle time ≥ tKC MIN;
VDD = MAX; Outputs open
Device deselected; VDD = MAX;
All inputs ≤ VIL or ≥ VIH;
All inputs static; CLK frequency = 0
Device deselected; VDD = MAX;
ADSC#, ADSP#, GW#, BWx#, ADV# ≥
VIH; All inputs ≤ VSS + 0.2 or ≥ VDD - 0.2;
Cycle time ≥ tKC MIN
UNITS NOTES
TQFP CAPACITANCE
DESCRIPTION
Control Input Capacitance
Input/Output Capacitance (DQ)
CONDITIONS
SYMBOL
TYP
MAX
UNITS
NOTES
TA = 25°C; f = 1 MHz;
CI
2.7
3.5
pF
4
VDD = 3.3V
CO
4
5
pF
4
Address Capacitance
CA
2.5
3.5
pF
4
Clock Capacitance
CCK
2.5
3.5
pF
4
NOTE: 1. IDD is specified with no output current and increases with faster cycle times. IDDQ increases with faster cycle times and
greater output loading.
2. “Device deselected” means device is in power-down mode as defined in the truth table. “Device selected” means
device is active (not in power-down mode).
3. Typical values are measured at 3.3V, 25°C, and 10ns cycle time.
4. This parameter is sampled.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
10
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
TQFP THERMAL RESISTANCE
DESCRIPTION
Thermal Resistance
(Junction to Ambient)
Thermal Resistance
(Junction to Top of Case)
CONDITIONS
SYMBOL
TYP
UNITS NOTES
Test conditions follow standard test methods
and procedures for measuring thermal
impedance, per EIA/JESD51.
θJA
40
°C/W
1
θJC
8
°C/W
1
NOTE: 1. This parameter is sampled.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
11
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS
(Note 1) (0°C ≤ TA ≤ +70°C; VDD = +3.3V +0.3V/-0.165V)
-6
DESCRIPTION
Clock
Clock cycle time
Clock frequency
Clock HIGH time
Clock LOW time
Output Times
Clock to output valid
Clock to output invalid
Clock to output in Low-Z
Clock to output in High-Z
OE# to output valid
OE# to output in Low-Z
OE# to output in High-Z
Setup Times
Address
Address status (ADSC#, ADSP#)
Address advance (ADV#)
Write signals
(BWa#-BWd#, BWE#, GW#)
Data-in
Chip enables (CE#, CE2#, CE2)
Hold Times
Address
Address status (ADSC#, ADSP#)
Address advance (ADV#)
Write signals
(BWa#-BWd#, BWE#, GW#)
Data-in
Chip enables (CE#, CE2#, CE2)
SYMBOL
MIN
tKC
6.0
fKF
tKH
tKL
tKQLZ
3.5
0
tAS
tADSS
tAAS
tWS
tDS
tCES
tAH
tADSH
tAAH
tWH
tDH
tCEH
100
3.2
3.2
4.0
5.0
1.5
1.5
4.0
4.0
0
3.5
MAX
10
1.5
1.5
3.5
3.5
tOEHZ
-10
MIN
133
1.9
1.9
1.5
1.5
tOEQ
-7.5
MAX
7.5
1.7
1.7
tKQHZ
tOELZ
MIN
166
tKQ
tKQX
MAX
5.0
5.0
0
4.0
4.5
UNITS
NOTES
ns
MHz
ns
ns
2
2
ns
ns
ns
ns
ns
ns
ns
3
3, 4, 5, 6
3, 4, 5, 6
7
3, 4, 5, 6
3, 4, 5, 6
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2.2
2.2
2.2
2.2
ns
ns
ns
ns
8, 9
8, 9
8, 9
8, 9
1.5
1.5
1.5
1.5
2.2
2.2
ns
ns
8, 9
8, 9
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
8, 9
8, 9
8, 9
8, 9
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
8, 9
8, 9
NOTE: 1. Test conditions as specified with the output loading shown in Figure 1 (VDDQ = +3.3V +0.3V/-0.165V) unless otherwise
noted.
2. Measured as HIGH above VIH and LOW below VIL.
3. This parameter is measured with the output loading shown in Figure 2.
4. This parameter is sampled.
5. Transition is measured ±500mV from steady state voltage.
6. Refer to Technical Note TN-58-09, “Synchronous SRAM Bus Contention Design Considerations,” for a more thorough
discussion on these parameters.
7. OE# is a “Don’t Care” when a byte write enable is sampled LOW.
8. A WRITE cycle is defined by at least one byte write enable LOW and ADSP# HIGH for the required setup and hold
times. A READ cycle is defined by all byte write enables HIGH and ADSC# or ADV# LOW or ADSP# LOW for the
required setup and hold times.
9. This is a synchronous device. All addresses must meet the specified setup and hold times for all rising edges of CLK
when either ADSP# or ADSC# is LOW and chip enabled. All other synchronous inputs must meet the setup and hold
times with stable logic levels for all rising edges of clock (CLK) when the chip is enabled. Chip enable must be valid at
each rising edge of CLK when either ADSP# or ADSC# is LOW to remain enabled.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
12
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
Output Load Equivalents
AC TEST CONDITIONS
Input pulse levels ................. VIH = (VDD/2.2) + 1.5V
Q
.................... VIL = (VDD/2.2) - 1.5V
Z O= 50Ω
Input rise and fall times ..................................... 1ns
Input timing reference levels ..................... VDD/2.2
50Ω
VT = 1.5V
Output reference levels ............................ VDDQ/2.2
Output load ............................. See Figures 1 and 2
Figure 1
+3.3V
LOAD DERATING CURVES
317
Q
The Micron 128K x 18, 64K x 32, and 64K x 36
SyncBurst SRAM timing is dependent upon the capacitive loading on the outputs.
Consult the factory for copies of I/O current versus
voltage curves.
5pF
351
Figure 2
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
13
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
SNOOZE MODE
The ZZ pin is an asynchronous, active HIGH input
that causes the device to enter SNOOZE MODE. When
the ZZ pin becomes a logic HIGH, ISB2Z is guaranteed
after the setup time tZZ is met. Any READ or WRITE
operation pending when the device enters SNOOZE
MODE is not guaranteed to complete successfully.
Therefore, SNOOZE MODE must not be initiated until
valid pending operations are completed.
SNOOZE MODE is a low-current, “power-down”
mode in which the device is deselected and current is
reduced to ISB2Z. The duration of SNOOZE MODE is
dictated by the length of time the ZZ pin is in a HIGH
state. After the device enters SNOOZE MODE, all inputs
except ZZ become gated inputs and are ignored.
SNOOZE MODE ELECTRICAL CHARACTERISTICS
DESCRIPTION
Current during SNOOZE MODE
CONDITIONS
SYMBOL
ZZ ≥ VIH
ZZ active to input ignored
MAX
UNITS
ISB2Z
10
mA
tZZ
2(tKC)
ns
1
ns
1
ns
1
ns
1
ZZ inactive to input sampled
tRZZ
ZZ active to snooze current
tZZI
tRZZI
ZZ inactive to exit snooze current
MIN
2(tKC)
2(tKC)
0
NOTES
NOTE: 1. This parameter is sampled.
SNOOZE MODE WAVEFORM
CLK
t ZZ
ZZ
I
t RZZ
t ZZI
SUPPLY
I ISB2Z
t RZZI
ALL INPUTS
DESELECT or READ Only
(except ZZ)
Outputs (Q)
High-Z
DON’T CARE
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
14
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
READ TIMING
tKC
CLK
tKL
tKH
tADSS tADSH
ADSP#
tADSS
tADSH
ADSC#
tAS
tAH
A1
ADDRESS
A2
tWS
A3
Burst continued with
new base address.
tWH
GW#, BWE#,
BWa#-BWd#
tCES
Deselect (NOTE 4)
cycle.
tCEH
CE#
(NOTE 2)
tAAS
tAAH
ADV#
ADV# suspends burst.
OE#
tOEQ
tKQ
t OELZ
tKQX
(NOTE 3)
t KQLZ
Q
t OEHZ
Q(A2)
Q(A1)
High-Z
t KQHZ
Q(A2 + 1)
Q(A2 + 2)
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
Q(A3)
t KQ
Burst wraps around
to its initial state.
(NOTE 1)
Single READ
BURST READ
DON’T CARE
UNDEFINED
READ TIMING PARAMETERS
-6
SYM
tKC
MIN
6.0
fKF
tKH
tKL
tKQLZ
166
tOEHZ
133
3.5
0
4.0
UNITS
100
ns
MHz
tAAS
5.0
ns
ns
ns
ns
ns
tAH
ns
ns
ns
tAAH
1.5
1.5
4.0
4.0
0
3.5
-6
MAX
3.2
3.2
1.5
1.5
3.5
3.5
tOEQ
-10
MIN
10
1.9
1.9
1.5
1.5
tKQHZ
tOELZ
-7.5
MIN
MAX
7.5
1.7
1.7
tKQ
tKQX
MAX
5.0
5.0
0
4.0
4.5
SYM
tAS
tADSS
tWS
tCES
tADSH
tWH
tCEH
MIN
1.5
1.5
-7.5
MAX
MIN
1.5
1.5
MAX
-10
MIN
2.2
2.2
MAX
UNITS
ns
ns
1.5
1.5
1.5
1.5
1.5
1.5
2.2
2.2
2.2
ns
ns
ns
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
NOTE: 1. Q(A2) refers to output from address A2. Q(A2 + 1) refers to output from the next internal burst address following A2.
2. CE2# and CE2 have timing identical to CE#. On this diagram, when CE# is LOW, CE2# is LOW and CE2 is HIGH. When
CE# is HIGH, CE2# is HIGH and CE2 is LOW.
3. Timing is shown assuming that the device was not enabled before entering into this sequence. OE# does not cause Q
to be driven until after the following clock rising edge.
4. Outputs are disabled within two clock cycles after deselect.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
15
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
WRITE TIMING
t KC
CLK
tKH
tKL
tADSS tADSH
ADSP#
ADSC# extends burst.
tADSS tADSH
tADSS tADSH
ADSC#
tAS
tAH
A1
ADDRESS
A2
A3
Byte write signals are ignored for first cycle when
ADSP# initiates burst.
tWS
tWH
BWE#,
BWa#-BWd#
(NOTE 5)
tWS
tWH
GW#
tCES
tCEH
CE#
(NOTE 2)
tAAS tAAH
ADV#
ADV# suspends burst.
(NOTE 4)
OE#
(NOTE 3)
tDS
D
tDH
D(A2)
D(A1)
High-Z
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
tOEHZ
(NOTE 1)
Q
BURST READ
Single WRITE
BURST WRITE
Extended BURST WRITE
DON’T CARE
UNDEFINED
WRITE TIMING PARAMETERS
-6
SYM
tKC
MIN
6.0
fKF
tKH
tKL
MAX
-7.5
MIN
MAX
7.5
166
1.7
1.7
tOEHZ
-10
MIN
10
133
1.9
1.9
ns
100
3.2
3.2
4.5
MHz
ns
ns
tAS
1.5
1.5
2.2
tADSS
1.5
1.5
1.5
1.5
1.5
1.5
2.2
2.2
2.2
ns
ns
ns
tWS
4.0
UNITS
ns
ns
tAAS
3.5
-6
MAX
-10
MIN
1.5
tCES
1.5
0.5
0.5
1.5
0.5
0.5
2.2
0.5
0.5
ns
ns
ns
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
tAH
tADSH
tAAH
tDH
tWH
tCEH
MAX
-7.5
MIN
MAX
1.5
SYM
tDS
MIN
2.2
MAX
UNITS
ns
NOTE: 1. D(A2) refers to input for address A2. D(A2 + 1) refers to input for the next internal burst address following A2.
2. CE2# and CE2 have timing identical to CE#. On this diagram, when CE# is LOW, CE2# is LOW and CE2 is HIGH. When
CE# is HIGH, CE2# is HIGH and CE2 is LOW.
3. OE# must be HIGH before the input data setup and held HIGH throughout the data hold time. This prevents input/
output data contention for the time period prior to the byte write enable inputs being sampled.
4. ADV# must be HIGH to permit a WRITE to the loaded address.
5. Full-width WRITE can be initiated by GW# LOW; or GW# HIGH and BWE#, BWa# and BWb# LOW for x18 device; or
GW# HIGH and BWE#, BWa#-BWd# LOW for x32 and x36 devices.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
16
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
READ/WRITE TIMING
tKC
CLK
tKL
tKH
tADSS
tADSH
ADSP#
ADSC#
tAS
A1
ADDRESS
tAH
A3
A2
BWE#,
BWa#-BWd#
(NOTE 4)
tCES
A4
tWS
tWH
tDS
tDH
A5
A6
D(A5)
D(A6)
tCEH
CE#
(NOTE 2)
ADV#
OE#
tKQ
tOELZ
D
High-Z
Q
High-Z
D(A3)
tOEHZ
tKQLZ
Q(A1)
(NOTE 1)
Q(A2)
Q(A4)
Back-to-Back READs
Single WRITE
Q(A4+1)
Q(A4+2)
Q(A4+3)
BURST READ
Back-to-Back
WRITEs
(NOTE 5)
DON’T CARE
UNDEFINED
READ/WRITE TIMING PARAMETERS
-6
SYM
tKC
MIN
MAX
6.0
fKF
-7.5
MIN
MAX
7.5
166
133
1.7
1.9
3.2
tKL
1.7
1.9
3.2
tKQLZ
tOELZ
3.5
1.5
0
tOEHZ
tAS
4.0
1.5
0
3.5
1.5
1.5
SYM
MIN
tADSS
100
ns
MHz
ns
1.5
1.5
1.5
1.5
2.2
2.2
ns
ns
1.5
1.5
0.5
1.5
1.5
0.5
2.2
2.2
0.5
ns
ns
ns
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
2.2
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
tDS
tCES
5.0
ns
ns
tADSH
4.5
ns
ns
ns
ns
tCEH
1.5
0
4.0
-10
UNITS
tWS
tAH
tWH
tDH
MAX
-7.5
MIN
MAX
MAX
10
tKH
tKQ
-6
-10
MIN
MIN
MAX
UNITS
NOTE: 1. Q(A4) refers to output from address A4. Q(A4 + 1) refers to output from the next internal burst address following A4.
2. CE2# and CE2 have timing identical to CE#. On this diagram, when CE# is LOW, CE2# is LOW and CE2 is HIGH. When
CE# is HIGH, CE2# is HIGH and CE2 is LOW.
3. The data bus (Q) remains in High-Z following a WRITE cycle unless an ADSP#, ADSC# or ADV# cycle is performed.
4. GW# is HIGH.
5. Back-to-back READs may be controlled by either ADSP# or ADSC#.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
17
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
100-PIN PLASTIC TQFP (JEDEC LQFP)
+0.10
-0.20
20.10 ±0.10
22.10
0.65 TYP
0.32
+0.06
-0.10
0.625
SEE DETAIL A
14.00 ±0.10
16.00 ±0.20
PIN #1 ID
0.15
+0.03
-0.02
1.40 ±0.05
GAGE PLANE
1.60 MAX
0.10
0.10
+0.10
-0.05
0.60 ±0.15
1.00 TYP
0.25
DETAIL A
NOTE: 1. All dimensions in millimeters MAX or typical here noted.
MIN
2. Package width and length do not include mold protrusion; allowable mold protrusion is 0.25mm per side.
DATA SHEET DESIGNATIONS
No Marking: This data sheet contains minimum and maximum limits specified over the complete power supply
and temperature range for production devices. Although considered final, these specifications are
subject to change, as further product development and data characterization sometimes occur.
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
E-mail: prodmktg@micron.com, Internet: http://www.micron.com, Customer Comment Line: 800-932-4992
Micron, SyncBurst, the M logo, and the Micron logo are trademarks and/or service marks of Micron Technology, Inc.
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
18
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.
NOT RECOMENDED FOR NEW DESIGNS
2Mb: 128K x 18, 64K x 32/36
PIPELINED, DCD SYNCBURST SRAM
REVISION HISTORY
Added “NOT RECOMENDED FOR NEW DESIGNS,” REV. C, Pub. 11/02, FINAL ........................ November/22/02
Removed 165-pin FBGA package, Rev. 6/01 .................................................................................................. June/7/01
Removed FBGA Part Marking Guide, REV 8/00, FINAL ........................................................................ August/22/00
Changed FBGA capacitance values, REV 8/00, FINAL ............................................................................. August/7/00
CI; TYP 2.5pF from 4pF; MAX. 3.5pF from 7pF
CO; TYP 4pF from 6pF; MAX. 5pF from 7pF
CCK; TYP 2.5pF from 5pF; MAX. 3.5pF from 6pF
Removed IT References, REV 7/00, FINAL ..................................................................................................... July/14/00
Added FBGA Part Marking Guide
Added Revision History to Datasheet
Removed IT from Part Number Example, REV 6/00, FINAL ....................................................................... June/21/00
Added # of datalines to the databus in x32/36 Block Diagram
Added Note - “Preliminary Package Data” to FBGA Capacitance and Thermal Resistance Tables
Changed heading on Mechanical Drawing from BGA to FBGA
Added 165-Pin FBGA package, REV 3/00, FINAL ....................................................................................... May/23/00
Added PRELIMINARY PACKAGE DATA to diagram
2Mb: 128K x 18, 64K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L128L18D_C.p65 – Rev. C, Pub. 11/02
19
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2002, Micron Technology, Inc.