MT66R7072A10AB5ZZW.ZCA

Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Features Product Brief LPDDR2-PCM and Mobile LPDDR2 121-Ball MCP MT66R7072A10AB5ZZW.ZCA, MT66R7072A10ACUXZW.ZCA MT66R5072A10ACUXZW.ZFA Features Figure 1: MCP Block Diagram Micron® LPDDR2-PCM and LPDDR2 components RoHS-compliant, “green” package Shared LPDDR2-PCM and LPDDR2 interfaces Space-saving multichip package Ultra low-voltage core and I/O power supplies – VDD1 = 1.7–1.95V – VDDCA/VDDQ = 1.14–1.3V – VDD2 = 1.14–1.3V • Wireless temperature range: –25°C to +85°C • • • • • LPDDR2-PCM Power Interface LPDDR2-PCM Specific Features LPDDR2 Power • Memory interface – 16-bit data bus width – Two data transfers per clock cycle – Clock frequency up to 400 MHz – Active to read/write delay: tRCD = 86ns – Configurable output drive strength • Memory architecture – 4-row data buffers (RDB) – Row data buffer size: 32B – 4-row address buffers (RAB) – Emulated block size: 128KB • Program/erase performance – Legacy programming mode up to 10MB/s (TYP) – Overwrite up to 3 MB/s (TYP) – Legacy block erase time: 60ms (TYP) • Dual operations – PROGRAM/ERASE in one partition while READ in other partitions – No delay between READ and WRITE operations • Locking scheme – All blocks locked at power-up – 8Mb lock region – Any combination of regions can be locked – Absolute write protection with VACC = V SS • Quality and reliability – Minimum 100k WRITE cycles/row PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN LPDDR2-PCM Device LPDDR2 Device LPDDR2 Mobile LPDDR2-Specific Features • • • • • • Programmable read and write latencies Programmable burst lengths: 4, 8, or 16 Partial-array self refresh (PASR) Deep power-down (DPD) mode Selectable output drive strength Adjustable clock frequency and clock stop capabilities Note: This product brief does not provide detailed device information. For the complete data sheet, which covers device functionality, operating modes, and specifications, or for further information on any aspect of the product, contact the Micron sales office. Part Number:The MT66R5072A10ACUXZW.ZFA is available as an engineering sample only. 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Features Part Numbering Information Micron LPDDR2-PCM and LPDDR2 devices are available in different configurations and densities. The MCP/PoP part numbering guide is available at www.micron.com/numbering. Figure 2: Part Number Chart MT 66R 707 2 A 1 0 A CUX* Z W . ZCA - ES Production Status Micron Technology Blank = Production Product Family ES = Engineering samples 66R = LPDDR2-PCM I/F + LPDDR2 MS = Mechanical samples Die Revision Density PCM xNAND 0 xLPDDR2 Contact factory N/A 1 32Mb = 4MB 16Mb = 2MB Operating Temperature Range 2 64Mb = 8MB 32Mb = 4MB W = –25°C to +85°C (Wireless) 3 128Mb = 16MB 64Mb = 8MB I = –40°C to +85°C (Industrial) 4 256Mb = 32MB 128Mb = 16MB 5 512Mb = 64MB 256Mb = 32MB Special Options 6 768Mb = 96MB 384Mb = 48MB Contact factory 7 1Gb = 128MB 512Mb = 64MB Package Codes Voltage Range (Core_ I/0) PCM LPDDR2 1 1.8_1.8 1.8_1.8 2 1.8_1.2 1.8_1.2 B5Z = 121-ball WFBGA, 11mmx10mmx0.8mm CUX = 121-ball WFBGA, 8mmx8mmx0.8mm *X = a null character used as a placeholder LPDDR2 Description Die Count 0 = N/A PCM LPDDR2 A = X16DDR2_S4 2KB Page A 1 1 B = X16DDR2_S2 2KB Page B 1 2 NAND Description PCM Configuration Bus Width Frequency 1 x16 166 MHz 2 x16 266 MHz 3 x16 333 MHz 4 x16 400 MHz Note: 0 = N/A 1. The MT66R5072A10ACUXZW.ZFA is available as an engineering sample only. This MCP will be packaged as 512Mb LPDDR-PCM and 512Mb LPDDR2, 121-ball, 8mm x 8mm x 0.8mm. Device Marking Due to the size of the package, the Micron-standard part number is not printed on the top of the device. Instead, an abbreviated device mark consisting of a 5-digit alphanumeric code is used. The abbreviated device marks are cross-referenced to the Micron part numbers at the FBGA Part Marking Decoder site: www.micron.com/decoder. To view the location of the abbreviated mark on the device, refer to customer service note CSN-11, “Product Mark/ Label,” at www.micron.com/csn. PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP MCP General Description MCP General Description Micron MCP products combine LPDDR2-PCM and Mobile LPDDR2 devices in a single MCP. These products target mobile applications with low-power, high-performance, and minimal package-footprint design requirements. The LPDDR2-PCM and Mobile LPDDR2 devices are also members of the Micron discrete memory products portfolio. The bus architecture of this device also supports separate LPDDR2-PCM and Mobile LPDDR2 functionality without concern for device interaction. Device Diagrams Figure 3: 121-Ball (LPDDR2-PCM and LPDDR2) Functional Block Diagram NV-CS# NV-CKE VDD1 LPDDR2–PCM VDDQ CK/CK# DQS[1:0] VDDCA DQS#[1:0] VSS DQ[15:0] VSSQ DM[1:0] VSSCA CA[9:0] VREFDQ LPDDR2 VREFCA D-CS# VDD2 PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN ZQ D-CKE 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Ball Assignments and Descriptions Ball Assignments and Descriptions Figure 4: 121-Ball VFBGA (LPDDR2-PCM x16; LPDDR2 x16) Ball Assignments A B C D E F G H J K L M N P R 1 2 3 4 5 6 7 8 9 10 11 DNU DNU NC NC NC NC VDD2 VSS VDDQ DNU DNU DNU NC NC NC NC NC VDD1 DQ15 DQ14 VSSQ DNU NC NC NC NC NC NC DQ11 DQ12 DQ13 VDD2 NC DQ10 VSSQ VSS ZQ DQ9 VDDQ VDD1 CA8 DQS1 VSSQ VSSCA CA7 DM1 VDDQ VDDCA CA5 VREF(DQ) VDD2 VDD2 VREF(CA) DM0 VDD1 CK CK# DQS0 VDDQ NV-CS0# D-CS# DQ6 VSSQ CA4 CA3 DQ5 VDDQ VDDCA CA2 CA1 DQ3 DQ2 VSSQ DNU VSSCA CA0 DNU DNU 1 2 CA9 DQ8 CA6 VSS NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC DQS1# DQS0# NC DQ7 NV-CKE0 RFU NC RFU D-CKE VACC DQ0 DQ1 DQ4 VSSQ DNU VSS VDD2 VDD1 VSS VDD2 VSS VDDQ DNU DNU 3 4 5 6 7 8 9 10 11 LPDDR2-specific PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 4 A B C D E F G H J K L M N P R LPDDR-PCM-specific Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Ball Assignments and Descriptions Table 1: x16 LPDDR2-PCM Ball Descriptions Symbol Type Description NV-CS# Input Chip select: CS# is considered part of the command code and is sampled at the rising edge of CK. When registered, CS# LOW enables, and CS# HIGH disables, the command decoder. All commands are masked when CS# is registered HIGH. NV-CKE Input Clock enable: CKE HIGH activates and CKE LOW deactivates the internal clock signals, input buffers, and output drivers. Power-saving modes are entered and exited via CKE transitions. CKE is considered part of the command code. CKE is sampled at the rising edge of CK. Table 2: x16 Mobile LPDDR2 Ball Descriptions Symbol Type D-CKE Input Clock enable. D-CKE is used for a single LPDDR2. For the signal description, refer to NV-CKE description. D-CS# Input Chip select: D-CS# is used for a single LPDDR2. For the signal description, refer to NV-CS# description. PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN Description 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Ball Assignments and Descriptions Table 3: LPDDR2 Ball Descriptions Symbol Type Description CA[9:0] Input Command/address inputs: Provide the command and address inputs according to the command truth table. CK, CK# Input Clock: CK and CK# are differential clock inputs. All CA inputs are sampled on both the positive and negative edge of CK. CS and CKE inputs are sampled at the positive edge of CK. AC timings are referenced to clock. DM[1:0] Input Data mask:DM is an input mask signal for write data. Although DM balls are input-only, the DM loading is designed to match that of DQ and DQS balls. DM[1:0] is DM for each of the two data bytes, respectively. DQ[15:0] Input/ output Data bus: Data inputs/outputs. DQS[3:0] DQS#[3:0] Input/ output Data strobe: Coordinates READ/WRITE transfers of data; one DQS/DQS# pair per DQ byte. VDD1 Supply VDD1: LPDDR2 power supply 1. VDD2 Supply VDD2: LPDDR2 power supply 2. VDDCA Supply VDDCA: LPDDR2 CA power supply. VDDQ Supply VDDQ: LPDDR2 I/O power supply. VREFCA Supply VREFCA: LPDDR2 reference for CA pins. VREFDQ Supply VREFDQ: LPDDR2 reference for DQ pins. VSSCA Supply VSSCA: LPDDR2 I/O ground. VSSQ Supply VSSQ: LPDDR2 I/O ground. VSS Supply VSS: Shared ground. ZQ Input External impedance (240-Ohm): This signal is used to calibrate the device output impedance. Table 4: Non-Device-Specific Descriptions Symbol Type DNU – Do not use: Must be grounded or left floating. NC – No connect: Not internally connected. PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN Description 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Phase Change Memory General Description Phase Change Memory General Description PCM is a new class of nonvolatile memory devices that stores information through a reversible structural phase change in a chalcogenide material. The material exhibits a change in both electrical and optical properties when changed from the amorphous (disordered) to the polycrystalline (regularly ordered) state. The amorphous state corresponds to the reset state (0); the polycrystalline state corresponds to the set state (1). In PCM, information is stored during the change in resistance the chalcogenide material undergoes during a phase change The device uses a DDR architecture on the command/address (CA) bus to reduce the number of input pins in the system. The 10-bit CA bus contains command, address, and row buffer information. Each command uses one clock cycle, during which command information is transferred on both the positive and negative edge of the clock. The device also uses a DDR architecture on the DQ pins to achieve high-speed operation. The LPDDR2-PCM device uses a complete set of commands that are compatible with the JEDEC industry-standard specification No. JESD209-2E. The DDR architecture is essentially a 4n-prefetch architecture with an interface designed to transfer two data bits per DQ every clock cycle at the I/O pins. A single read or write access effectively consists of a single, 4n-bit wide, one-clock-cycle data transfer at the internal core and four corresponding, n-bit wide, one-half-clock-cycle data transfers at the I/O pins. The device is organized into four RABs and RDBs, 32 bytes each. Read or write accesses to device are performed issuing a sequence of PREACTIVE commands to deliver part of the row address to one of four RABs in the device; ACTIVATE commands to fill one of the four RDBs in the device; and READ or WRITE commands. Operations other than array reads are performed by accessing an overlay window that is mapped over the array space of the memory. The overlay window base address is programmed using the mode registers. The device can be erased electrically at block level and programmed in-system on a word-by-word basis using a V DD1 supply for the circuitry and V DDQ supply for the I/O pins. An optional V ACC power supply is provided for factory programming. A multiple partition architecture allows dual operations: While writing or erasing in one partition, READ operations are possible in other partitions. Only one partition at a time can be in write or erase mode. Erase can be suspended to perform a WRITE or READ operation in any other block except for the one being erased, and then resumed. Writing can be suspended to read data at any memory location except the one being modified, and then resumed. To issue embedded commands like PROGRAM or ERASE, the operation code and data are written to the overlay window of the memory. An internal program/erase controller manages the timings necessary for embedded operations. The end of a WRITE or ERASE operation can be detected and any error conditions identified in the status register. The command set required to control the memory is consistent with the JEDEC standard. Read and write accesses to the device are burst oriented at different frequencies using a differential clock up to 400 MHz. Accesses start at a selected location and continue for a configured number of locations. PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Phase Change Memory General Description The device features a power-down mode. When clock enable (CKE) is registered LOW, power-down mode is enabled. In this condition, the power consumption is reduced to the standby value. The device features an individual locking region scheme that allows any region to be locked or unlocked, enabling code and data protection. The array is divided into 8Mb locking regions. All locking regions have three levels of protection. They can be locked and locked down individually, preventing any accidental writing or erasure. There is also additional hardware protection against writing and erasing. When V ACC < V ACCLK, all lock regions are protected against program or erase. All lock regions are locked at power-up. VACC shall not change during the period starting from at least 1µs prior to the initiation of any embedded operation until that embedded operation is complete. The device includes a 64-bit segment area, containing a unique 64-bit device number and a 256-bit (16-word) protection register area that is one-time programmable (OTP) by the user. The user-programmable region can be permanently protected, programming the 16-bit protection register lock. See Security Features and Protection Registers for more details. PCM offers bit alterability or an overwrite feature: PCM technology supports the ability to change each memory bit independently from 0 to 1 or 1 to 0 without erasing the block first. Bit alterability enables software to write to the nonvolatile memory similar to writing to RAM or EEPROM without the overhead of erasing blocks prior to writing. Bitalterable writes use command sequences similar to word writes and buffer writes. This mode is often referred to as overwrite as opposed to program, in which only 0s are written and 1s are treated as masks. The device is rated at 100,000 write alterations per row. The device is supplied with all the bits erased (set to 1). PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP LPDDR2-PCM Organization LPDDR2-PCM Organization Array The 512Mb device has a 512-block array and is divided into 64Mb partitions. There are 8 partitions containing 64 blocks of 128KB each. The 1Gb device has a 1024-block array and is divided into 64Mb partitions. There are 16 partitions containing 64 blocks of 128KB each. Memory Map Table 5: 512Mb LPDDR2-PCM Partition 7 Partition 0 64Mb 64Mb Block Number Size (KB) Word Address Range 511 128 1FF0000–1FFFFFF ⋮ ⋮ ⋮ 448 128 1C00000–1C0FFFF 63 128 03F0000–03FFFFF ⋮ ⋮ ⋮ 0 128 0000000–000FFFF Block Number Size (KB) Word Address Range 1023 128 3FF0000–3FFFFFF ⋮ ⋮ ⋮ 960 128 3C00000–3C0FFFF 63 128 03F0000–03FFFFF ⋮ ⋮ ⋮ 0 128 0000000–000FFFF Table 6: 1Gb LPDDR2-PCM Partition 15 Partition 0 64Mb 64Mb PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Package Dimensions Package Dimensions Figure 5: 121-Ball VFBGA – 8mm x 8mm x 0.8mm (Package Code: CU) Seating plane A 121X Ø0.32 Dimensions apply to solder balls post-reflow on Ø0.30 SMD ball pads. 0.08 A Ball A1 ID (covered by SR) 10 11 8 9 6 7 4 5 Ball A1 ID 2 3 1 A B C D E F G H J K L M N P R 7 CTR 8 ±0.1 0.5 TYP 0.7 ±0.1 0.5 TYP 5 CTR 0.16 MIN 8 ±0.1 Note: 1. All dimensions are in millimeters. PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Package Dimensions Figure 6: 121-Ball VFBGA – 11m x 10mm x 0.8mm (Package Code: B5Z) Seating plane A 121X Ø0.3 ±0.05 0.08 A Ball A1 ID Ball A1 ID 10 8 6 4 2 11 9 7 5 3 1 A B C D E F G H J K L M N P R 7 CTR 10 ±0.1 0.5 TYP 0.5 TYP 0.8 MAX 5 CTR 0.15 MIN 11 ±0.1 Note: 1. All dimensions are in millimeters. PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved. Product Brief – 121-Ball LPDDR2-PCM and LPDDR2 MCP Revision History Revision History Rev. B – 12/12 • Added new part number Rev. A – 08/12 • Initial release 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 www.micron.com/productsupport Customer Comment Line: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. PDF: 09005aef84e25954 121ball_pcm_lpddr2_product_brief.pdf – Rev. B 12/12 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2012 Micron Technology, Inc. All rights reserved.