0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
PC28F00AP33EF0

PC28F00AP33EF0

  • 厂商:

    MICRON(镁光)

  • 封装:

    TBGA64

  • 描述:

    IC FLASH 1GBIT PAR 64EASYBGA

  • 详情介绍
  • 数据手册
  • 价格&库存
PC28F00AP33EF0 数据手册
512Mb, 1Gb, 2Gb: P33-65nm Features Micron Parallel NOR Flash Embedded Memory (P33-65nm) JS28F512P33BFD, JS28F512P33TFA, JS28F512P33EFA PC28F512P33BFD, PC28F512P33TFA, PC28F512P33EFA JS28F00AP33BFA, JS28F00AP33TFA, JS28F00AP33EFA PC28F00AP33BFA, PC28F00AP33TFA, PC28F00AP33EFA, PC28F00BP33EFA Features • Security – One-time programmable register: 64 OTP bits, programmed with unique information from Micron; 2112 OTP bits available for customer programming – Absolute write protection: V PP = V SS – Power-transition erase/program lockout – Individual zero-latency block locking – Individual block lock-down – Password access • Software – 25μs (TYP) program suspend – 25μs (TYP) erase suspend – Flash Data Integrator optimized – Basic command set and extended function Interface (EFI) command set compatible – Common flash interface • Density and Packaging – 56-lead TSOP package (512Mb, 1Gb) – 64-ball Easy BGA package (512Mb, 1Gb, 2Gb) – 16-bit wide data bus • Quality and reliabilty – JESD47 compliant – Operating temperature: –40°C to +85°C – Minimum 100,000 ERASE cycles per block – 65nm process technology • High performance • Easy BGA package features – 95ns initial access for 512Mb, 1Gb Easy BGA – 100ns initial access for 2Gb Easy BGA – 25ns 16-word asychronous page read mode – 52 MHz (Easy BGA) with zero WAIT states and 17ns clock-to-data output synchronous burst read mode – 4-, 8-, 16-, and continuous word options for burst mode • TSOP package features – 105ns initial access for 512Mb, 1Gb TSOP • Both Easy BGA and TSOP package features – Buffered enhanced factory programming (BEFP) at 2 MB/s (TYP) using a 512-word buffer – 3.0V buffered programming at 1.46 MB/s (TYP) using a 512-word buffer • Architecture – MLC: highest density at lowest cost – Symmetrically blocked architecture (512Mb, 1Gb, 2Gb) – Asymmetrically blocked architecture (512Mb, 1Gb); four 32KB parameter blocks: top or bottom configuration – 128KB main blocks – Blank check to verify an erased block • Voltage and power – VCC (core) voltage: 2.3–3.6V – VCCQ (I/O) voltage: 2.3–3.6V – Standy current: 70µA (TYP) for 512Mb; 75µA (TYP) for 1Gb – 52 MHz continuous synchronous read current: 21mA (TYP), 24mA (MAX) PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. 512Mb, 1Gb, 2Gb: P33-65nm Features Discrete and MCP Part Numbering Information Devices are shipped from the factory with memory content bits erased to 1. For available options, such as packages or for further information, contact your Micron sales representative. Part numbers can be verified at www.micron.com. Feature and specification comparison by device type is available at www.micron.com/products. Contact the factory for devices not found. Note: Not all part numbers listed here are available for ordering. Table 1: Discrete Part Number Information Part Number Category Package Category Details JS = 56-lead TSOP, lead free PC = 64-ball Easy BGA, lead-free Product Line 28F = Micron Flash memory Density 512 = 512Mb 00A = 1Gb 00B = 2Gb Product Family P33 (VCC = 2.3–3.6V; VCCQ = 2.3–3.6V) Parameter Location B/T = Bottom/Top parameter E = Symmetrical Blocks Lithography F = 65nm Features * Note: 1. The last digit is assigned randomly to cover packaging media, features, or other specific configuration information. Sample part number: JS28F512P33EF* Table 2: Standard Part Numbers Density Configuration Medium JS PC 512Mb Bottom boot Tray JS28F512P33BFD PC28F512P33BFD Tape & Reel – – Top boot Uniform 1Gb Bottom boot Top boot Uniform 2Gb Uniform PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN Tray JS28F512P33TFA PC28F512P33TFA Tape & Reel – – Tray JS28F512P33EFA PC28F512P33EFA Tape & Reel – – Tray JS28F00AP33BFA PC28F00AP33BFA Tape & Reel – – Tray JS28F00AP33TFA PC28F00AP33TFA Tape & Reel – – Tray JS28F00AP33EFA PC28F00AP33EFA Tape & Reel – – Tray – PC28F00BP33EFA Tape & Reel – – 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Features Contents General Description ......................................................................................................................................... 7 Virtual Chip Enable Description ........................................................................................................................ 8 Memory Map ................................................................................................................................................... 9 Package Dimensions ....................................................................................................................................... 11 Pinouts and Ballouts ....................................................................................................................................... 13 Signal Descriptions ......................................................................................................................................... 15 Bus Operations ............................................................................................................................................... 17 Read .......................................................................................................................................................... 17 Write .......................................................................................................................................................... 17 Output Disable ........................................................................................................................................... 17 Standby ..................................................................................................................................................... 17 Reset .......................................................................................................................................................... 18 Device Command Codes ................................................................................................................................. 19 Device Command Bus Cycles .......................................................................................................................... 22 Read Operations ............................................................................................................................................. 24 Asynchronous Single Word Read ..................................................................................................................... 24 Asynchronous Page Mode Read (Easy BGA Only) ............................................................................................. 24 Synchronous Burst Mode Read (Easy BGA Only) .............................................................................................. 25 Read CFI ........................................................................................................................................................ 25 Read Device ID ............................................................................................................................................... 25 Device ID Codes ............................................................................................................................................. 26 Program Operations ....................................................................................................................................... 27 Word Programming (40h) ........................................................................................................................... 27 Buffered Programming (E8h, D0h) .............................................................................................................. 27 Buffered Enhanced Factory Programming (80h, D0h) ................................................................................... 28 Program Suspend ....................................................................................................................................... 30 Program Resume ........................................................................................................................................ 31 Program Protection .................................................................................................................................... 31 Erase Operations ............................................................................................................................................ 32 BLOCK ERASE Command ........................................................................................................................... 32 BLANK CHECK Command .......................................................................................................................... 32 ERASE SUSPEND Command ....................................................................................................................... 33 ERASE RESUME Command ........................................................................................................................ 33 Erase Protection ......................................................................................................................................... 33 Security Operations ........................................................................................................................................ 34 Block Locking ............................................................................................................................................. 34 BLOCK LOCK Command ............................................................................................................................ 34 BLOCK UNLOCK Command ....................................................................................................................... 34 BLOCK LOCK DOWN Command ................................................................................................................. 34 Block Lock Status ....................................................................................................................................... 34 Block Locking During Suspend ................................................................................................................... 35 Selectable OTP Blocks ................................................................................................................................. 36 Password Access ......................................................................................................................................... 36 Status Register ................................................................................................................................................ 37 Read Status Register ................................................................................................................................... 37 Clear Status Register ................................................................................................................................... 38 Configuration Register .................................................................................................................................... 39 Read Configuration Register ....................................................................................................................... 39 Read Mode ................................................................................................................................................. 39 Latency Count ............................................................................................................................................ 40 PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Features End of Wordline Considerations .................................................................................................................. WAIT Signal Polarity and Functionality ........................................................................................................ WAIT Delay ................................................................................................................................................ Burst Sequence .......................................................................................................................................... Clock Edge ................................................................................................................................................. Burst Wrap ................................................................................................................................................. Burst Length .............................................................................................................................................. One-Time Programmable Registers ................................................................................................................. Read OTP Registers ..................................................................................................................................... Program OTP Registers ............................................................................................................................... Lock OTP Registers ..................................................................................................................................... Common Flash Interface ................................................................................................................................ READ CFI Structure Output ........................................................................................................................ Flowcharts ..................................................................................................................................................... Power and Reset Specifications ....................................................................................................................... Power Supply Decoupling ........................................................................................................................... Maximum Ratings and Operating Conditions .................................................................................................. DC Electrical Specifications ............................................................................................................................ AC Test Conditions and Capacitance ............................................................................................................... AC Read Specifications ................................................................................................................................... AC Write Specifications ................................................................................................................................... Program and Erase Characteristics .................................................................................................................. Revision History ............................................................................................................................................. Rev. C – 12/13 ............................................................................................................................................. Rev. B – 11/13 ............................................................................................................................................. Rev. A – 8/13 ............................................................................................................................................... PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 4 41 42 43 43 44 44 44 45 45 46 46 48 48 62 71 72 73 74 76 78 85 91 92 92 92 92 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Features List of Figures Figure 1: Easy BGA Block Diagram ................................................................................................................... 8 Figure 2: Memory Map – 512Mb and 1Gb ......................................................................................................... 9 Figure 3: Memory Map – 2Gb ......................................................................................................................... 10 Figure 4: 56-Pin TSOP – 14mm x 20mm .......................................................................................................... 11 Figure 5: 64-Ball Easy BGA – 8mm x 10mm x 1.2mm ....................................................................................... 12 Figure 6: 56-Lead TSOP Pinout – 512Mb and 1Gb ........................................................................................... 13 Figure 7: 64-Ball Easy BGA (Top View – Balls Down) – 512Mb, 1Gb, and 2Gb .................................................... 14 Figure 8: Example V PP Supply Connections .................................................................................................... 31 Figure 9: Block Locking State Diagram ........................................................................................................... 35 Figure 10: First Access Latency Count ............................................................................................................ 40 Figure 11: Example Latency Count Setting Using Code 3 ................................................................................. 41 Figure 12: End of Wordline Timing Diagram ................................................................................................... 41 Figure 13: OTP Register Map .......................................................................................................................... 46 Figure 14: Word Program Procedure ............................................................................................................... 62 Figure 15: Buffer Program Procedure .............................................................................................................. 63 Figure 16: Buffered Enhanced Factory Programming (BEFP) Procedure ........................................................... 64 Figure 17: Block Erase Procedure ................................................................................................................... 65 Figure 18: Program Suspend/Resume Procedure ............................................................................................ 66 Figure 19: Erase Suspend/Resume Procedure ................................................................................................. 67 Figure 20: Block Lock Operations Procedure ................................................................................................... 68 Figure 21: OTP Register Programming Procedure ............................................................................................ 69 Figure 22: Status Register Procedure .............................................................................................................. 70 Figure 23: Reset Operation Waveforms ........................................................................................................... 72 Figure 24: AC Input/Output Reference Timing ................................................................................................ 76 Figure 25: Transient Equivalent Load Circuit .................................................................................................. 76 Figure 26: Clock Input AC Waveform .............................................................................................................. 76 Figure 27: Asynchronous Single-Word Read (ADV# LOW) ................................................................................ 80 Figure 28: Asynchronous Single-Word Read (ADV# Latch) ............................................................................... 80 Figure 29: Asynchronous Page Mode Read ...................................................................................................... 81 Figure 30: Synchronous Single-Word Array or Nonarray Read .......................................................................... 82 Figure 31: Continuous Burst Read with Output Delay ..................................................................................... 83 Figure 32: Synchronous Burst Mode 4-Word Read ........................................................................................... 84 Figure 33: Write to Write Timing .................................................................................................................... 87 Figure 34: Asynchronous Read to Write Timing ............................................................................................... 87 Figure 35: Write to Asynchronous Read Timing ............................................................................................... 88 Figure 36: Synchronous Read to Write Timing ................................................................................................ 89 Figure 37: Write to Synchronous Read Timing ................................................................................................ 90 PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Features List of Tables Table 1: Discrete Part Number Information ...................................................................................................... 2 Table 2: Standard Part Numbers ....................................................................................................................... 2 Table 3: Virtual Chip Enable Truth Table for Easy BGA Packages ........................................................................ 8 Table 4: TSOP and Easy BGA Signal Descriptions ............................................................................................ 15 Table 5: Bus Operations ................................................................................................................................. 17 Table 6: Command Codes and Definitions ...................................................................................................... 19 Table 7: Command Bus Cycles ....................................................................................................................... 22 Table 8: Device ID Information ...................................................................................................................... 25 Table 9: Device ID codes ................................................................................................................................ 26 Table 10: BEFP Requirements ........................................................................................................................ 29 Table 11: BEFP Considerations ...................................................................................................................... 29 Table 12: Status Register Description .............................................................................................................. 37 Table 13: Read Configuration Register ............................................................................................................ 39 Table 14: End of Wordline Data and WAIT State Comparison ........................................................................... 42 Table 15: WAIT Functionality Table ................................................................................................................ 42 Table 16: Burst Sequence Word Ordering ........................................................................................................ 43 Table 17: Example of CFI Output (x16 device) as a Function of Device and Mode ............................................. 48 Table 18: CFI Database: Addresses and Sections ............................................................................................. 49 Table 19: CFI ID String ................................................................................................................................... 49 Table 20: System Interface Information .......................................................................................................... 50 Table 21: Device Geometry ............................................................................................................................ 51 Table 22: Block Region Map Information ........................................................................................................ 51 Table 23: Primary Vendor-Specific Extended Query ........................................................................................ 52 Table 24: Optional Features Field ................................................................................................................... 54 Table 25: One Time Programmable (OTP) Space Information .......................................................................... 54 Table 26: Burst Read Information ................................................................................................................... 55 Table 27: Partition and Block Erase Region Information .................................................................................. 56 Table 28: Partition Region 1 Information: Top and Bottom Offset/Address ....................................................... 57 Table 29: Partition Region 1 Information ........................................................................................................ 57 Table 30: Partition Region 1: Partition and Erase Block Map Information ......................................................... 60 Table 31: CFI Link Information – 2Gb ............................................................................................................. 61 Table 32: Power and Reset .............................................................................................................................. 71 Table 33: Maximum Ratings ........................................................................................................................... 73 Table 34: Operating Conditions ...................................................................................................................... 73 Table 35: DC Current Characteristics .............................................................................................................. 74 Table 36: DC Voltage Characteristics .............................................................................................................. 75 Table 37: Test Configuration: Worst-Case Speed Condition .............................................................................. 76 Table 38: Capacitance .................................................................................................................................... 77 Table 39: AC Read Specifications .................................................................................................................... 78 Table 40: AC Write Specifications ................................................................................................................... 85 Table 41: Program and Erase Specifications .................................................................................................... 91 PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm General Description General Description The Micron Parallel NOR Flash memory is the latest generation of Flash memory devices. Benefits include more density in less space, high-speed interface device, and support for code and data storage. Features include high-performance synchronous-burst read mode, fast asynchronous access times, low power, flexible security options, and three industry-standard package choices. The product family is manufactured using Micron 65nm process technology. The NOR Flash device provides high performance at low voltage on a 16-bit data bus. Individually erasable memory blocks are sized for optimum code and data storage. Upon initial power up or return from reset, the device defaults to asynchronous pagemode read. Configuring the read configuration register enables synchronous burstmode reads. In synchronous burst mode, output data is synchronized with a user-supplied clock signal. A WAIT signal provides easy CPU-to-flash memory synchronization. In addition to the enhanced architecture and interface, the device incorporates technology that enables fast factory PROGRAM and ERASE operations. Designed for low-voltage systems, the devIce supports READ operations with V CC at the low voltages, and ERASE and PROGRAM operations with V PP at the low voltages or V PPH. Buffered enhanced factory programming (BEFP) provides the fastest Flash array programming performance with V PP at V PPH, which increases factory throughput. With V PP at low voltages, V CC and V PP can be tied together for a simple, ultra low-power design. In addition to voltage flexibility, a dedicated V PP connection provides complete data protection when VPP ≤ V PPLK. A command user interface is the interface between the system processor and all internal operations of the device. The device automatically executes the algorithms and timings necessary for block erase and program. A status register indicates ERASE or PROGRAM completion and any errors that may have occurred. An industry-standard command sequence invokes program and erase automation. Each ERASE operation erases one block. The erase suspend feature enables system software to pause an ERASE cycle to read or program data in another block. Program suspend enables system software to pause programming to read other locations. Data is programmed in word increments (16 bits). The protection register enables unique device identification that can be used to increase system security. The individual block lock feature provides zero-latency block locking and unlocking. The device includes enhanced protection via password access; this new feature supports write and/or read access protection of user-defined blocks. In addition, the device also provides the full-device OTP security feature. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Virtual Chip Enable Description Virtual Chip Enable Description The 2Gb device employs a virtual chip enable feature, which combines two 1Gb die with a common chip enable, CE# for Easy BGA packages. The maximum address bit is then used to select between the die pair with CE# asserted. When CE# is asserted and the maximum address bit is LOW, the lower parameter die is selected; when CE# is asserted and the maximum address bit is HIGH, the upper parameter die is selected. Table 3: Virtual Chip Enable Truth Table for Easy BGA Packages Die Selected CE# A[MAX] Lower parameter die L L Upper parameter die L H Figure 1: Easy BGA Block Diagram Easy BGA (Dual Die) Top/Bottom Parameter Configuration CE# Top Parameter Die WP# RST# OE# VCC WE# VPP VCCQ CLK ADV# Bottom Parameter Die VSS DQ[15:0] A[MAX:1] PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN WAIT 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Memory Map Memory Map Figure 2: Memory Map – 512Mb and 1Gb A[25:1] 512Mb and A[26:1] 1Gb 3FF0000 - 3FFFFFF 64 KWord Block 1026 3FF0000 - 3FFFFFF 64 KWord Block 1023 1FF0000 - 1FFFFFF 64 KWord Block 514 1FF0000 - 1FFFFFF 64 KWord Block 511 FF0000 - FFFFFF 64 KWord Block 258 FF0000 - FFFFFF 64 KWord Block 255 1Gb 512Mb 1Gb 512Mb 020000 - 02FFFF 64 KWord Block 5 010000 - 01FFFF 64 KWord Block 4 00C000 - 00FFFF 16 KWord Block 3 030000 - 03FFFF 64 KWord Block 3 008000 - 00BFFF 16 KWord Block 2 020000 - 02FFFF 64 KWord Block 2 004000 - 007FFF 16 KWord Block 1 010000 - 01FFFF 64 KWord Block 1 000000 - 003FFF 16 KWord Block 0 000000 - 00FFFF 64 KWord Block 0 Bottom Boot 512Mb and 1Gb, World-Wide x16 Mode Symetrically Blocked 512Mb and 1Gb, World-Wide x16 Mode 1FFC000 - 1FFFFFF 16 KWord Block 514 3FFC000 - 3FFFFFF 16 KWord Block 1026 1FF8000 - 1FFBFFF 16 KWord Block 513 3FF8000 - 3FFBFFF 16 KWord Block 1025 1FF4000 - 1FF7FFF 16 KWord Block 512 3FF4000 - 3FF7FFF 16 KWord Block 1024 1FF0000 - 1FF3FFF 16 KWord Block 511 3FF0000 - 3FF3FFF 16 KWord Block 1023 1FE0000 - 1FEFFFF 64 KWord Block 510 3FE0000 - 3FEFFFF 64 KWord Block 1022 512Mb 1Gb 010000 - 01FFFF 64 KWord Block 1 010000 - 01FFFF 64 KWord Block 1 000000 - 00FFFF 64 KWord Block 0 000000 - 00FFFF 64 KWord Block 0 Top Boot 512Mb, World Wide x16 Mode PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN Top Boot 1Gb, World Wide x16 Mode 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Memory Map Figure 3: Memory Map – 2Gb A[27:1] 2Gb (1Gb/1Gb) 7FF0000 - 7FFFFFF 64 KWord Block 2047 4011000 - 401FFFF 64 KWord Block 1025 4000000 - 400FFFF 64 KWord Block 1024 3FF0000 - 3FFFFFF 64 KWord Block 1023 1FF0000 - 1FFFFFF 64 KWord Block 511 2Gb FF0000 - FFFFFF 64 KWord Block 255 1Gb 512Mb 020000 - 02FFFF 64 KWord Block 2 010000 - 01FFFF 64 KWord Block 1 000000 - 00FFFF 64 KWord Block 0 World-Wide x16 Mode PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Package Dimensions Package Dimensions Figure 4: 56-Pin TSOP – 14mm x 20mm 20 ±0.2 18.4 ±0.2 0.995 ±0.03 Pin #1 index See notes 2 See note 2 0.5 TYP 14.00 ±0.2 0.22 ±0.05 See note 2 See note 2 0.25 ±0.1 0.15 ±0.05 0.10 3° +2° -3° See Detail A 1.20 MAX Seating plane 0.05 MIN 0.60 ±0.10 Detail A Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. All dimensions are in millimeters. Drawing not to scale. 2. One dimple on package denotes pin 1; if two dimples, then the larger dimple denotes pin 1. Pin 1 will always be in the upper left corner of the package, in reference to the product mark. 3. For the lead width value of 0.22 ±0.05, there is also a legacy value of 0.15 ±0.05. 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Package Dimensions Figure 5: 64-Ball Easy BGA – 8mm x 10mm x 1.2mm 0.78 TYP 0.25 MIN Seating plane 0.1 1.00 TYP 64X Ø0.43 ±0.1 1.5 ±0.1 8 7 6 5 4 3 2 Ball A1 ID Ball A1 ID 1 0.5 ±0.1 A B C D 8 ±0.1 E F 1.00 TYP G H 10 ±0.1 1.20 MAX Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. All dimensions are in millimeters. Drawing not to scale. 2. The 512Mb device does not contain the A1 ID ball located on the back side of the device. 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Pinouts and Ballouts Pinouts and Ballouts Figure 6: 56-Lead TSOP Pinout – 512Mb and 1Gb A 16 A 15 A 14 A 13 A 12 A 11 A 10 A9 A 23 A 22 A 21 VSS RFU WE # WP # A 20 A 19 A 18 A8 A7 A6 A5 A4 A3 A2 A24 A25 A26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 56-Lead TSOP Pinout 14mm x 20mm Top View 1. 2. 3. 4. 5. 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 WAIT A17 DQ 15 DQ 7 DQ 14 DQ 6 DQ 13 DQ 5 DQ 12 DQ 4 ADV # CLK RST# VPP DQ 11 DQ 3 DQ 10 DQ 2 VCCQ DQ 9 DQ 1 DQ 8 DQ 0 VCC OE# VSS CE# A1 A1 is the least significant address bit. ADV# must be tied to VSS or driven to LOW throughout the asynchronous read mode. A25 is valid for 512Mb densities and above; otherwise, it is a no connect (NC). A26 is valid for 1Gb densities and above; otherwise, it is a no connect (NC). One dimple on package denotes Pin 1 which will always be in the upper left corner of the package, in reference to the product mark. 13 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Pinouts and Ballouts Figure 7: 64-Ball Easy BGA (Top View – Balls Down) – 512Mb, 1Gb, and 2Gb 1 2 3 4 5 6 7 8 A1 A6 A8 VPP A13 VCC A18 A22 A2 VSS A9 CE# A14 A25 A19 A26 A3 A7 A10 A12 A15 WP# A20 A21 A4 A5 A11 RST# VCCQ VCCQ A16 A17 DQ8 DQ1 DQ9 DQ3 DQ4 CLK DQ15 RFU RFU DQ0 DQ10 DQ11 DQ12 ADV# WAIT OE# A23 RFU DQ2 VCCQ DQ5 DQ6 DQ14 WE# A27 VSS VCC VSS DQ13 VSS DQ7 A24 A B C D E F G H Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. 2. 3. 4. 5. A1 is the least significant address bit. A25 is valid for 512Mb densities and above; otherwise, it is a no connect (NC). A26 is valid for 1Gb densities and above; otherwise, it is a no connect (NC). A27 is valid for 2Gb densities and above; otherwise, it is a no connect (NC). One dimple on package denotes Pin 1 which will always be in the upper left corner of the package, in reference to the product mark. 14 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Signal Descriptions Signal Descriptions Table 4: TSOP and Easy BGA Signal Descriptions Symbol Type Name and Function A[MAX:1] Input Address inputs: Device address inputs. Note: Unused active address pins should not be left floating; tie them to VCCQ or VSS according to specific design requirements. ADV# Input Address valid: Active LOW input. During synchronous READ operations, addresses are latched on the rising edge of ADV#, or on the next valid CLK edge with ADV# LOW, whichever occurs first. In asynchronous mode, the address is latched when ADV# goes HIGH or continuously flows through if ADV# is held LOW. Note: Designs not using ADV# must tie it to VSS to allow addresses to flow through. CE# Input Chip enable: Active LOW input. CE# LOW selects the associated die. When asserted, internal control logic, input buffers, decoders, and sense amplifiers are active. When de-asserted, the associated die is deselected, power is reduced to standby levels, data and wait outputs are placed in High-Z. Note: CE# must be driven HIGH when device is not in use. CLK Input Clock: Synchronizes the device with the system bus frequency in synchronous-read mode. During synchronous READs, addresses are latched on the rising edge of ADV#, or on the next valid CLK edge with ADV# LOW, whichever occurs first. Note: Designs not using CLK for synchronous read mode must tie it to VCCQ or VSS. OE# Input Output enable: Active LOW input. OE# LOW enables the device’s output data buffers during READ cycles. OE# HIGH places the data outputs and WAIT in High-Z. RST# Input Reset: Active LOW input. RST# resets internal automation and inhibits WRITE operations. This provides data protection during power transitions. RST# HIGH enables normal operation. Exit from reset places the device in asynchronous read array mode. WP# Input Write protect: Active LOW input. WP# LOW enables the lock-down mechanism. Blocks in lock-down cannot be unlocked with the Unlock command. WP# HIGH overrides the lockdown function enabling blocks to be erased or programmed using software commands. Note: Designs not using WP# for protection could tie it to VCCQ or VSS without additional capacitor. WE# Input Write enable: Active LOW input. WE# controls writes to the device. Address and data are latched on the rising edge of WE# or CE#, whichever occurs first. VPP Power/Input Erase and program power: A valid voltage on this pin allows erasing or programming. Memory contents cannot be altered when VPP ≤ VPPLK. Block erase and program at invalid VPP voltages should not be attempted. Set VPP = VPPL for in-system PROGRAM and ERASE operations. To accommodate resistor or diode drops from the system supply, the VIH level of VPP can be as low as VPPL,min . VPP must remain above VPPL,min to perform in-system modification. VPP may be 0V during READ operations. VPP can be connected to 9V for a cumulative total not to exceed 80 hours. Extended use of this pin at 9V may reduce block cycling capability. DQ[15:0] Input/Output Data input/output: Inputs data and commands during WRITE cycles; outputs data during memory, status register, protection register, and read configuration register reads. Data balls float when the CE# or OE# are de-asserted. Data is internally latched during writes. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Signal Descriptions Table 4: TSOP and Easy BGA Signal Descriptions (Continued) Symbol Type WAIT Output Name and Function Wait: Indicates data valid in synchronous array or non-array burst reads. Read configuration register bit 10 (RCR.10, WT) determines its polarity when asserted. This signal's active output is VOL or VOH when CE# and OE# are VIL. WAIT is High-Z if CE# or OE# is VIH. • In synchronous array or non-array read modes, this signal indicates invalid data when asserted and valid data when de-asserted. • In asynchronous page mode, and all write modes, this signal is de-asserted. VCC Power Device core power supply: Core (logic) source voltage. Writes to the array are inhibited when VCC ≤ VLKO. Operations at invalid VCC voltages should not be attempted. VCCQ Power Output power supply: Output-driver source voltage. Ground: Connect to system ground. Do not float any VSS connection. VSS Power RFU — Reserved for future use: Reserved by Micron for future device functionality and enhancement. These should be treated in the same way as a DU signal. DU — Do not use: Do not connect to any other signal, or power supply; must be left floating. NC — No connect: No internal connection; can be driven or floated. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Bus Operations Bus Operations CE# LOW and RST# HIGH enable READ operations. The device internally decodes upper address inputs to determine the accessed block. ADV# LOW opens the internal address latches. OE# LOW activates the outputs and gates selected data onto the I/O bus. Bus cycles to/from the device conform to standard microprocessor bus operations. Bus operations and the logic levels that must be applied to the device control signal inputs are shown here. Table 5: Bus Operations Bus Operation RST# CLK ADV# CE# OE# WE# WAIT DQ[15:0] Notes Asynchronous H X L L L H De-asserted Output - Synchronous H Running L L L H Driven Output - WRITE H X L L H L High-Z Input 1 OUTPUT DISABLE H X X L H H High-Z High-Z 2 STANDBY H X X H X X High-Z High-Z 2 RESET L X X X X X High-Z High-Z 2, 3 READ 1. Refer to the Device Command Bus Cycles for valid DQ[15:0] during a WRITE operation. 2. X = "Don’t Care" (H or L). 3. RST# must be at VSS ± 0.2V to meet the maximum specified power-down current. Notes: Read To perform a READ operation, RST# and WE# must be de-asserted while CE# and OE# are asserted. CE# is the device-select control. When asserted, it enables the device. OE# is the data-output control. When asserted, the addressed flash memory data is driven onto the I/O bus. Write To perform a WRITE operation, both CE# and WE# are asserted while RST# and OE# are de-asserted. During a WRITE operation, address and data are latched on the rising edge of WE# or CE#, whichever occurs first. The Command Bus Cycles table shows the bus cycle sequence for each of the supported device commands, while the Command Codes and Definitions table describes each command. Note: WRITE operations with invalid V CC and/or V PP voltages can produce spurious results and should not be attempted. Output Disable When OE# is de-asserted, device outputs DQ[15:0] are disabled and placed in High-Z state, WAIT is also placed in High-Z. Standby When CE# is de-asserted the device is deselected and placed in standby, substantially reducing power consumption. In standby, the data outputs are placed in High-Z, independent of the level placed on OE#. Standby current (ICCS) is the average current measPDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Bus Operations ured over any 5ms time interval, 5μs after CE# is de-asserted. During standby, average current is measured over the same time interval 5μs after CE# is de-asserted. When the device is deselected (while CE# is de-asserted) during a PROGRAM or ERASE operation, it continues to consume active power until the PROGRAM or ERASE operation is completed. Reset As with any automated device, it is important to assert RST# when the system is reset. When the system comes out of reset, the system processor attempts to read from the device if it is the system boot device. If a CPU reset occurs with no device reset, improper CPU initialization may occur because the device may be providing status information rather than array data. Micron devices enable proper CPU initialization following a system reset through the use of the RST# input. RST# should be controlled by the same low-true reset signal that resets the system CPU. After initial power-up or reset, the device defaults to asynchronous read array mode, and the status register is set to 0x80. Asserting RST# de-energizes all internal circuits, and places the output drivers in High-Z. When RST# is asserted, the device shuts down the operation in progress, a process which takes a minimum amount of time to complete. When RST# has been de-asserted, the device is reset to asynchronous read array state. When device returns from a reset (RST# de-asserted), a minimum wait is required before the initial read access outputs valid data. Also, a minimum delay is required after a reset before a write cycle can be initiated. After this wake-up interval passes, normal operation is restored. Note: If RST# is asserted during a PROGRAM or ERASE operation, the operation is terminated and the memory contents at the aborted location (for a program) or block (for an erase) are no longer valid, because the data may have been only partially written or erased. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Device Command Codes Device Command Codes The system CPU provides control of all in-system READ, WRITE, and ERASE operations of the device via the system bus. The device manages all block-erase and word-program algorithms. Device commands are written to the CUI to control all device operations. The CUI does not occupy an addressable memory location; it is the mechanism through which the device is controlled. Note: For a dual device, all setup commands should be re-issued to the device when a different die is selected. Table 6: Command Codes and Definitions Mode Device Mode Code Description Read Read array 0xFF Places the device in read array mode. Array data is output on DQ[15:0]. Read status register 0x70 Places the device in read status register mode. The device enters this mode after a PROGRAM or ERASE command is issued. Status register data is output on DQ[7:0]. Read device ID or read configuration register 0x90 Places device in read device identifier mode. Subsequent reads output manufacturer/device codes, configuration register data, block lock status, or protection register data on DQ[15:0]. Read CFI 0x98 Places the device in read CFI mode. Subsequent reads output CFI information on DQ[7:0]. Clear status register 0x50 The device sets status register error bits. The clear status register command is used to clear the SR error bits. Word program setup 0x40 First cycle of a 2-cycle programming command; prepares the CUI for a WRITE operation. On the next write cycle, the address and data are latched and the device executes the programming algorithm at the addressed location. During PROGRAM operations, the device responds only to READ STATUS REGISTER and PROGRAM SUSPEND commands. CE# or OE# must be toggled to update the status register in asynchronous read. CE# or ADV# must be toggled to update the status register data for synchronous non-array reads. The READ ARRAY command must be issued to read array data after programming has finished. Buffered program 0xE8 This command loads a variable number of words up to the buffer size of 512 words onto the program buffer. Buffered program confirm 0xD0 The CONFIRM command is issued after the data streaming for writing into the buffer is completed. The device then performs the buffered program algorithm, writing the data from the buffer to the memory array. BEFP setup 0x80 First cycle of a two-cycle command; initiates buffered enhanced factory program mode (BEFP). The CUI then waits for the BEFP CONFIRM command, 0xD0, that initiates the BEFP algorithm. All other commands are ignored when BEFP mode begins. BEFP confirm 0xD0 If the previous command was BEFP SETUP (0x80), the CUI latches the address and data, and prepares the device for BEFP mode. Write PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Device Command Codes Table 6: Command Codes and Definitions (Continued) Mode Device Mode Code Description Erase Block erase setup 0x20 First cycle of a two-cycle command; prepares the CUI for a BLOCK ERASE operation. The device performs the erase algorithm on the block addressed by the ERASE CONFIRM command. If the next command is not the ERASE CONFIRM (0xD0) command, the CUI sets status register bits SR4 and SR5, and places the device in read status register mode. Block erase confirm 0xD0 If the first command was BLOCK ERASE SETUP (0x20), the CUI latches the address and data, and the device erases the addressed block. During BLOCK ERASE operations, the device responds only to READ STATUS REGISTER and ERASE SUSPEND commands. CE# or OE# must be toggled to update the status register in asynchronous read. CE# or ADV# must be toggled to update the status register data for synchronous non-array reads. Program or erase suspend 0xB0 This command issued to any device address initiates a suspend of the currently-executing program or BLOCK ERASE operation. The status register indicates successful suspend operation by setting either SR2 (program suspended) or SR6 (erase suspended), along with SR7 (ready). The device remains in the suspend mode regardless of control signal states (except for RST# asserted). Suspend resume 0xD0 This command issued to any device address resumes the suspended PROGRAM or BLOCK ERASE operation. Block lock setup 0x60 First cycle of a two-cycle command; prepares the CUI for block lock configuration changes. If the next command is not BLOCK LOCK (0x01), BLOCK UNLOCK (0xD0), or BLOCK LOCK DOWN (0x2F), the CUI sets status register bits SR5 and SR4, indicating a command sequence error. Block lock 0x01 If the previous command was BLOCK LOCK SETUP (0x60), the addressed block is locked. Block unlock 0xD0 If the previous command was BLOCK LOCK SETUP (0x60), the addressed block is unlocked. If the addressed block is in a lock down state, the operation has no effect. Block lock down 0x2F If the previous command was BLOCK LOCK SETUP (0x60), the addressed block is locked down. OTP register or lock register program setup 0xC0 First cycle of a two-cycle command; prepares the device for a OTP REGISTER or LOCK REGISTER PROGRAM operation. The second cycle latches the register address and data, and starts the programming algorithm to program data the OTP array. Read configuration register setup 0x60 First cycle of a two-cycle command; prepares the CUI for device read configuration. If the SET READ CONFIGURATION REGISTER command (0x03) is not the next command, the CUI sets status register bits SR4 and SR5, indicating a command sequence error. Read configuration register 0x03 If the previous command was READ CONFIGURATION REGISTER SETUP (0x60), the CUI latches the address and writes A[16:1] to the read configuration register for Easy BGA and TSOP, A[15:0] for QUAD+. Following a CONFIGURE READ CONFIGURATION REGISTER command, subsequent READ operations access array data. Suspend Protection Configuration PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Device Command Codes Table 6: Command Codes and Definitions (Continued) Mode Device Mode Code Description Blank Check Block blank check 0xBC First cycle of a two-cycle command; initiates the BLANK CHECK operation on a main block. Block blank check confirm 0xD0 Second cycle of blank check command sequence; it latches the block address and executes blank check on the main array block. Extended function interface 0xEB First cycle of a multiple-cycle command; initiate operation using extended function interface. The second cycle is a Sub-Op-Code, the data written on third cycle is one less than the word count; the allowable value on this cycle are 0–511. The subsequent cycles load data words into the program buffer at a specified address until word count is achieved. EFI PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Device Command Bus Cycles Device Command Bus Cycles Device operations are initiated by writing specific device commands to the command user interface (CUI). Several commands are used to modify array data including WORD PROGRAM and BLOCK ERASE commands. Writing either command to the CUI initiates a sequence of internally timed functions that culminate in the completion of the requested task. However, the operation can be aborted by either asserting RST# or by issuing an appropriate suspend command. Table 7: Command Bus Cycles Second Bus Cycle Op Addr1 Data2 Op Addr1 Data2 READ ARRAY 1 WRITE DnA 0xFF – – – READ DEVICE IDENTIFIER ≥2 WRITE DnA 0x90 READ DBA + IA ID READ CFI ≥2 WRITE DnA 0x98 READ DBA + CFI-A CFI-D READ STATUS REGISTER 2 WRITE DnA 0x70 READ DnA SRD CLEAR STATUS REGISTER 1 WRITE DnA 0x50 – – – WORD PROGRAM WD Command Read Program First Bus Cycle Bus Cycles Mode 2 WRITE WA 0x40 WRITE WA PROGRAM3 >2 WRITE WA 0xE8 WRITE WA N-1 BUFFERED ENHANCED FACTORY PROGRAM (BEFP)4 >2 WRITE WA 0x80 WRITE WA 0xD0 BUFFERED Erase BLOCK ERASE 2 WRITE BA 0x20 WRITE BA 0xD0 Suspend PROGRAM/ERASE SUSPEND 1 WRITE DnA 0xB0 – – – PROGRAM/ERASE RESUME 1 WRITE DnA 0xD0 – – – BLOCK LOCK 2 WRITE BA 0x60 WRITE BA 0x01 BLOCK UNLOCK 2 WRITE BA 0x60 WRITE BA 0xD0 BLOCK LOCK DOWN 2 WRITE BA 0x60 WRITE BA 0x2F PROGRAM OTP REGISTER 2 WRITE PRA 0xC0 WRITE OTP-RA OTP-D PROGRAM LOCK REGISTER 2 WRITE LRA 0xC0 WRITE LRA LRD Configuration CONFIGURE READ CONFIGURATION REGISTER 2 WRITE RCD 0x60 WRITE RCD 0x03 Blank Check BLOCK BLANK CHECK 2 WRITE BA 0xBC WRITE BA D0 EFI EXTENDED FUNCTION INTERFACE 5 >2 WRITE WA 0xEB Write WA Sub-Op code Protection Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. First command cycle address should be the same as the operation’s target address. DBA = Device base address (needed for dual die 512Mb device); DnA = Address within the device; IA = Identification code address offset; CFI-A = Read CFI address offset; WA = Word address of memory location to be written; BA = Address within the block; OTP-RA = Protection register address; LRA = Lock register address; RCD = Read configuration register data on A[16:1] for Easy BGA and TSOP, A[15:0] for QUAD+ package. 2. ID = Identifier data; CFI-D = CFI data on DQ[15:0]; SRD = Status register data; WD = Word data; N = Word count of data to be loaded into the write buffer; OTP-D = Protection register data; LRD = Lock register data. 22 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Device Command Bus Cycles 3. The second cycle of the BUFFERED PROGRAM command is the word count of the data to be loaded into the write buffer. This is followed by up to 512 words of data. Then the CONFIRM command (0xD0) is issued, triggering the array programming operation. 4. The CONFIRM command (0xD0) is followed by the buffer data. 5. The second cycle is a Sub-Op-Code, the data written on third cycle is N-1; 1≤ N ≤ 512. The subsequent cycles load data words into the program buffer at a specified address until word count is achieved, after the data words are loaded, the final cycle is the confirm cycle 0xD0). PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Read Operations Read Operations The device supports two read modes: asynchronous page mode and synchronous burst mode. Asynchronous page mode is the default read mode after device power-up or a reset. Under asynchronous page mode, the device can also perform single word read. The read configuration register must be configured to enable synchronous burst reads of the array. The device can be in any of four read states: read array, read identifier, read status, or read CFI. Upon power-up, or after a reset, the device defaults to read array. To change the read state, the appropriate READ command must be written to the device. Asynchronous Single Word Read To perform an asynchronous single word read, an address is driven onto the address bus, and CE# is asserted. Note: To perform an asynchronous single word read for a TSOP package, ADV# must be LOW throughout the READ cycle. For an Easy BGA package, ADV# can be driven HIGH to latch the address or be held LOW throughout the READ cycle. WE# and RST# must already have been de-asserted. WAIT is set to a de-asserted state during single word mode, as determined by bit 10 of the read configuration register. CLK is not used for asynchronous single word reads, and is ignored. If asynchronous reads are to be performed only, CLK should be tied to a valid V IH or V SS level, WAIT can be floated, and ADV# must be tied to ground. After OE# is asserted, the data is driven onto DQ[15:0] after an initial access time tAVQV or tGLQV delay. Asynchronous Page Mode Read (Easy BGA Only) Note: Asynchronous Page Mode Read is supported only in the main array. Following a device power-up or reset, asynchronous page mode is the default read mode and the device is set to read array. However, to perform array reads after any other device operation (WRITE operation), the READ ARRAY command must be issued in order to read from the array. Asynchronous page mode reads can only be performed when read configuration register bit RCR15 is set. To perform an asynchronous page-mode read, an address is driven onto the address bus, and CE# and ADV# are asserted. WE# and RST# must already have been de-asserted. WAIT is de-asserted during asynchronous page mode. ADV# can be driven HIGH to latch the address, or it must be held LOW throughout the READ cycle. CLK is not used for asynchronous page mode reads, and is ignored. If only asynchronous reads are to be performed, CLK should be tied to a valid V IH or V SS level, WAIT signal can be floated, and ADV# must be tied to ground. Array data is driven onto DQ[15:0] after an initial access time tAVQV delay. In asynchronous page mode, 16 data words are “sensed” simultaneously from the array and loaded into an internal page buffer. The buffer word corresponding to the initial address on the address bus is driven onto DQ[15:0] after the initial access delay. The lowest four address bits determine which word of the 16-word page is output from the data buffer at any given time. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Synchronous Burst Mode Read (Easy BGA Only) Synchronous Burst Mode Read (Easy BGA Only) Read configuration register bits RCR[15:0] must be set before synchronous burst operation can be performed. Synchronous burst mode can be performed for both array and non-array reads such as read ID, read status, or read query. To perform a synchronous burst read, an initial address is driven onto the address bus, and CE# and ADV# are asserted. WE# and RST# must already have been de-asserted. ADV# is asserted, and then de-asserted to latch the address. Alternately, ADV# can remain asserted throughout the burst access, in which case the address is latched on the next valid CLK edge while ADV# is asserted. During synchronous array and non-array read modes, the first word is output from the data buffer on the next valid CLK edge after the initial access latency delay. Subsequent data is output on valid CLK edges following a minimum delay. However, for a synchronous non-array read, the same word of data will be output on successive clock edges until the burst length requirements are satisfied. Refer to the timing diagrams for more detailed information. Read CFI The READ CFI command instructs the device to output CFI data when read. See Common Flash Interface for details on issuing the READ CFI command, and for details on addresses and offsets within the CFI database. Read Device ID The READ DEVICE IDENTIFIER command instructs the device to output manufacturer code, device identifier code, block lock status, protection register data, or configuration register data. Table 8: Device ID Information Item Address Data Manufacturer code 0x00 0x89 Device ID code 0x01 ID (see the Device ID Codes table ) Block lock configuration Block is unlocked Block is locked Block is not locked down Block is locked down Block base address + 0x02 Read configuration register General purpose register 0x05 RCR contents Device base address + 0x07 Lock register 0 Lock bit DQ0 = 0b0 DQ0 = 0b1 DQ1 = 0b0 DQ1 = 0b1 0x80 General purpose register data PR-LK0 data 64-bit factory-programmed OTP register 0x81–0x84 Factory OTP register data 64-bit user-programmable OTP register 0x85–0x88 User OTP register data Lock register 1 128-bit user-programmable protection registers PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 0x89 PR-LK1 OTP register lock data 0x8A–0x109 25 OTP register data Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Device ID Codes Device ID Codes Table 9: Device ID codes ID Code Type Device Code Device Identifier Codes Device Density –T (Top Parameter) –B (Bottom Parameter) –E/F (Symmetrical Blocks) 512Mb 8964 8965 899E 1Gb 8966 8967 899F Note: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. The 2Gb devices do not have a unique device ID associated with them. Each die within the stack can be identified by device ID codes. 26 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Program Operations Program Operations Successful programming requires the addressed block to be unlocked. If the block is locked down, WP# must be de-asserted and the block must be unlocked before attempting to program the block. Attempting to program a locked block causes a program error (SR4 and SR1 set) and termination of the operation. See Security Modes for details on locking and unlocking blocks. Word Programming (40h) Word programming operations are initiated by writing the WORD PROGRAM SETUP command to the device (see the Command Codes and Definitions table). This is followed by a second write to the device with the address and data to be programmed. The device outputs status register data when read (see the Word Program Flowchart). V PP must be above V PPLK, and within the specified V PPL MIN/MAX values. During programming, the device executes a sequence of internally-timed events that program the desired data bits at the addressed location, and verifies that the bits are sufficiently programmed. Programming the array changes 1s to 0s. Memory array bits that are 0s can be changed to 1s only by erasing the block (see Erase Operations). The status register can be examined for programming progress and errors by reading at any address. The device remains in the read status register state until another command is written to the device. SR7 indicates the programming status while the sequence executes. Commands that can be issued to the device during programming are PROGRAM SUSPEND, READ STATUS REGISTER, READ DEVICE IDENTIFIER, READ CFI, and READ ARRAY (this returns unknown data). When programming has finished, SR4 (when set) indicates a programming failure. If SR3 is set, the device could not perform the WORD PROGRAMMING operation because VPP was outside of its acceptable limits. If SR1 is set, the WORD PROGRAMMING operation attempted to program a locked block, causing the operation to abort. Before issuing a new command, the status register contents should be examined and then cleared using the CLEAR STATUS REGISTER command. Any valid command can follow, when word programming has completed. Buffered Programming (E8h, D0h) The device features a 512-word buffer to enable optimum programming performance. For buffered programming, data is first written to an on-chip write buffer. Then the buffer data is programmed into the array in buffer-size increments. This can improve system programming performance significantly over non-buffered programming. When the BUFFERED PROGRAMMING SETUP command is issued, status register information is updated and reflects the availability of the buffer. SR7 indicates buffer availability: if set, the buffer is available; if cleared, the buffer is not available. Note: The device default state is to output SR data after the BUFFERED PROGRAMMING SETUP command. CE# and OE# LOW drive device to update status register. It is not allowed to issue 70h to read SR data after E8h command; otherwise, 70h would be counted as word count. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Program Operations On the next write, a word count is written to the device at the buffer address. This tells the device how many data words will be written to the buffer, up to the maximum size of the buffer. On the next write, a device start address is given along with the first data to be written to the flash memory array. Subsequent writes provide additional device addresses and data. All data addresses must lie within the start address plus the word count. Optimum programming performance and lower power usage are obtained by aligning the starting address at the beginning of a 512-word boundary (A[9:1] = 0x00 for Easy BGA and TSOP, A[8:0] for QUAD+ package; see Part Numbering Information). The maximum buffer size would be 256-word if the misaligned address range is crossing a 512-word boundary during programming. After the last data is written to the buffer, the BUFFERED PROGRAMMING CONFIRM command must be issued to the original block address. The device begins to program buffer contents to the array. If a command other than the BUFFERED PROGRAMMING CONFIRM command is written to the device, a command sequence error occurs and SR[7,5,4] are set. If an error occurs while writing to the array, the device stops programming, and SR[7,4] are set, indicating a programming failure. When buffered programming has completed, additional buffer writes can be initiated by issuing another BUFFERED PROGRAMMING SETUP command and repeating the buffered program sequence. Buffered programming may be performed with V PP = V PPL or V PPH (see Operating Conditions for limitations when operating the device with V PP = VPPH). If an attempt is made to program past an erase-block boundary using the BUFFERED PROGRAM command, the device aborts the operation. This generates a command sequence error, and SR[5,4] are set. If buffered programming is attempted while V PP is at or below V PPLK, SR[4,3] are set. If any errors are detected that have set status register bits, the status register should be cleared using the CLEAR STATUS REGISTER command. Buffered Enhanced Factory Programming (80h, D0h) Buffered enhanced factory programming (BEFP) speeds up multilevel cell (MLC) programming. The enhanced programming algorithm used in BEFP eliminates traditional programming elements that drive up overhead in device programmer systems. BEFP consists of three phases: setup, program/verify, and exit (see the BEFP Flowchart). It uses a write buffer to spread MLC program performance across 512 data words. Verification occurs in the same phase as programming to accurately program the cell to the correct bit state. A single two-cycle command sequence programs the entire block of data. This enhancement eliminates three write cycles per buffer: two commands and the word count for each set of 512 data words. Host programmer bus cycles fill the device write buffer followed by a status check. SR0 indicates when data from the buffer has been programmed into sequential array locations. Following the buffer-to-flash array programming sequence, the device increments internal addressing to automatically select the next 512-word array boundary. This aspect of BEFP saves host programming equipment the address bus setup overhead. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Program Operations With adequate continuity testing, programming equipment can rely on the device’s internal verification to ensure that the device has programmed properly. This eliminates the external post-program verification and its associated overhead. Table 10: BEFP Requirements Parameter/Issue Requirement Notes Case temperature TC = 30°C ± 10°C VCC Nominal VCC VPP Driven to VPPH Setup and confirm Target block must be unlocked before issuing the BEFP Setup and Confirm commands. Programming The first-word address (WA0) of the block to be programmed must be held constant from the setup phase through all data streaming into the target block, until transition to the exit phase is desired. Buffer alignment WA0 must align with the start of an array buffer boundary. 1 1. Word buffer boundaries in the array are determined by the lowest 9 address bits (0x000 through 0x1FF). The alignment start point is 0x000. Note: Table 11: BEFP Considerations Parameter/Issue Requirement Notes Cycling For optimum performance, cycling must be limited below 50 ERASE cycles per block. Programming blocks BEFP programs one block at a time; all buffer data must fall within a single block. Suspend 1 2 BEFP cannot be suspended. Programming the ar- Programming to the array can occur only when the buffer is full. ray 3 1. Some degradation in performance may occur if this limit is exceeded, but the internal algorithm continues to work properly. 2. If the internal address counter increments beyond the block's maximum address, addressing wraps around to the beginning of the block. 3. If the number of words is less than 512, remaining locations must be filled with 0xFFFF. Notes: BEFP Setup Phase: After receiving the BEFP SETUP and CONFIRM command sequence, SR7 (ready) is cleared, indicating that the device is busy with BEFP algorithm startup. A delay before checking SR7 is required to allow the device enough time to perform all of its setups and checks (block lock status, V PP level, etc.). If an error is detected, SR4 is set and BEFP operation terminates. If the block was found to be locked, SR1 is also set. SR3 is set if the error occurred due to an incorrect V PP level. Note: Reading from the device after the BEFP SETUP and CONFIRM command sequence outputs status register data. Do not issue the READ STATUS REGISTER command; it will be interpreted as data to be loaded into the buffer. BEFP Program/Verify Phase: After the BEFP setup phase has completed, the host programming system must check SR[7,0] to determine the availability of the write buffer for data streaming. SR7 cleared indicates the device is busy and the BEFP program/verify phase is activated. SR0 indicates the write buffer is available. Two basic sequences repeat in this phase: loading of the write buffer, followed by buffer data programming to the array. For BEFP, the count value for buffer loading is always PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Program Operations the maximum buffer size of 512 words. During the buffer-loading sequence, data is stored to sequential buffer locations starting at address 0x00. Programming of the buffer contents to the array starts as soon as the buffer is full. If the number of words is less than 512, the remaining buffer locations must be filled with 0xFFFF. Note: The buffer must be completely filled for programming to occur. Supplying an address outside of the current block's range during a buffer-fill sequence causes the algorithm to exit immediately. Any data previously loaded into the buffer during the fill cycle is not programmed into the array. The starting address for data entry must be buffer size aligned; if not, the BEFP algorithm will be aborted, the program fails, and the (SR4) flag will be set. Data words from the write buffer are directed to sequential memory locations in the array; programming continues from where the previous buffer sequence ended. The host programming system must poll SR0 to determine when the buffer program sequence completes. SR0 cleared indicates that all buffer data has been transferred to the array; SR0 set indicates that the buffer is not available yet for the next fill cycle. The host system may check full status for errors at any time, but it is only necessary on a block basis after BEFP exit. After the buffer fill cycle, no WRITE cycles should be issued to the device until SR0 = 0 and the device is ready for the next buffer fill. Note: Any spurious writes are ignored after a BUFFER FILL operation and when internal program is proceeding. The host programming system continues the BEFP algorithm by providing the next group of data words to be written to the buffer. Alternatively, it can terminate this phase by changing the block address to one outside of the current block’s range. The program/verify phase concludes when the programmer writes to a different block address; data supplied must be 0xFFFF. Upon program/verify phase completion, the device enters the BEFP exit phase. Program Suspend Issuing the PROGRAM SUSPEND command while programming suspends the programming operation. This allows data to be accessed from the device other than the one being programmed. The PROGRAM SUSPEND command can be issued to any device address. A PROGRAM operation can be suspended to perform reads only. Additionally, a PROGRAM operation that is running during an erase suspend can be suspended to perform a READ operation. When a programming operation is executing, issuing the PROGRAM SUSPEND command requests the device to suspend the programming algorithm at predetermined points. The device continues to output status register data after the PROGRAM SUSPEND command is issued. Programming is suspended when SR[7,2] are set. To read data from the device, the READ ARRAY command must be issued. READ ARRAY, READ STATUS REGISTER, READ DEVICE IDENTIFIER, READ CFI, and PROGRAM RESUME valid commands during a program suspend. During a program suspend, de-asserting CE# places the device in standby, reducing active current. V PP must remain at its programming level, and WP# must remain unchanged while in program suspend. If RST# is asserted, the device is reset. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Program Operations Program Resume The RESUME command instructs the device to continue programming, and automatically clears SR[7,2]. This command can be written to any address. If error bits are set, the status register should be cleared before issuing the next command. RST# must remain de-asserted. Program Protection When V PP = V IL, absolute hardware write protection is provided for all device blocks. If VPP is at or below V PPLK, programming operations halt and SR3 is set, indicating a V PPlevel error. Block lock registers are not affected by the voltage level on V PP; they may still be programmed and read, even if V PP is less than V PPLK. Figure 8: Example VPP Supply Connections VCC VCC VPP < 10K Ω VPP -Factory programming with VPP = VPPH -Complete with program/erase protection when VPP < VPPLK VCC VCC VPP = VPPH VPP VCC VCC PROT# VPP -Low voltage programming only -Logic control of device protection VCC VCC VPP -Low voltage programming only -Low voltage and factory programming -Full device protection unavailable PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Erase Operations Erase Operations BLOCK ERASE Command ERASE operations are performed on a block basis. An entire block is erased each time a BLOCK ERASE command sequence is issued, and only one block is erased at a time. When a block is erased, each bit within that block reads as a logical 1. A BLOCK ERASE operation is initiated by writing the BLOCK ERASE SETUP command to the address of the block to be erased, followed by the BLOCK ERASE CONFIRM command. If the device is placed in standby (CE# de-asserted) during a BLOCK ERASE operation, the device completes the operation before entering standby. The V PP value must be above V PPLK and the block must be unlocked. During a BLOCK ERASE operation, the device executes a sequence of internally-timed events that conditions, erases, and verifies all bits within the block. Erasing the array changes the value in each cell from a 1 to a 0. Memory block array cells that with a value of 1 can be changed to 0 only by programming the block. The status register can be examined for block erase progress and errors by reading any address. The device remains in the read status register state until another command is written. SR0 indicates whether the addressed block is erasing. SR7 is set upon erase completion. SR7 indicates block erase status while the sequence executes. When the BLOCK ERASE operation has completed, SR5 = 1 (set) indicates an erase failure. SR3 = 1 indicates that the device could not perform the BLOCK ERASE operation because V PP was outside of its acceptable limits. SR1 = 1 indicates that the BLOCK ERASE operation attempted to erase a locked block, causing the operation to abort. Before issuing a new command, the status register contents should be examined and then cleared using the CLEAR STATUS REGISTER command. Any valid command can follow after the BLOCK ERASE operation has completed. The BLOCK ERASE operation is aborted by performing a reset or powering down the device. In either case, data integrity cannot be ensured, and it is recommended to erase again the blocks aborted. BLANK CHECK Command The BLANK CHECK operation determines whether a specified main block is blank; that is, completely erased. Other than a BLANK CHECK operation, only a BLOCK ERASE operation can ensure a block is completely erased. BLANK CHECK is especially useful when a BLOCK ERASE operation is interrupted by a power loss event. A BLANK CHECK operation can apply to only one block at a time. The only operation allowed simultaneously is a READ STATUS REGISTER operation. SUSPEND and RESUME operations and a BLANK CHECK operation are mutually exclusive. A BLANK CHECK operation is initiated by writing the BLANK CHECK SETUP command to the block address, followed by the CHECK CONFIRM command. When a successful command sequence is entered, the device automatically enters the read status state. The device then reads the entire specified block and determines whether any bit in the block is programmed or over-erased. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 32 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Erase Operations BLANK CHECK operation progress and errors are determined by reading the status register at any address within the block being accessed. SR7 = 0 is a BLANK CHECK busy status. SR7 = 1 is a BLANK CHECK operation complete status. The status register should be checked for any errors and then cleared. If the BLANK CHECK operation fails, meaning the block is not completely erased, SR5 = 1. CE# or OE# toggle (during polling) updates the status register. The READ STATUS REGISTER command must always be followed by a CLEAR STATUS REGISTER command. The device remains in status register mode until another command is written to the device. Any command can follow once the BLANK CHECK command is complete. ERASE SUSPEND Command The ERASE SUSPEND command suspends a BLOCK ERASE operation that is in progress, enabling access to data in memory locations other than the one being erased. The ERASE SUSPEND command can be issued to any device address. A BLOCK ERASE operation can be suspended to perform a WORD or BUFFER PROGRAM operation, or a READ operation within any block except the block that is erase suspended. When a BLOCK ERASE operation is executing, issuing the ERASE SUSPEND command requests the device to suspend the erase algorithm at predetermined points. The device continues to output status register data after the ERASE SUSPEND command is issued. Block erase is suspended when SR[7,6] are set. To read data from the device (other than an erase-suspended block), the READ ARRAY command must be issued. During erase suspend, a PROGRAM command can be issued to any block other than the erase-suspended block. Block erase cannot resume until program operations initiated during erase suspend complete. READ ARRAY, READ STATUS REGISTER, READ DEVICE IDENTIFIER, READ CFI, and ERASE RESUME are valid commands during erase suspend. Additionally, CLEAR STATUS REGISTER, PROGRAM, PROGRAM SUSPEND, BLOCK LOCK, BLOCK UNLOCK, and BLOCK LOCK DOWN are valid commands during an ERASE SUSPEND operation. During an erase suspend, de-asserting CE# places the device in standby, reducing active current. V PP must remain at a valid level, and WP# must remain unchanged while in erase suspend. If RST# is asserted, the device is reset. ERASE RESUME Command The ERASE RESUME command instructs the device to continue erasing, and automatically clears SR[7,6]. This command can be written to any address. If status register error bits are set, the status register should be cleared before issuing the next instruction. RST# must remain de-asserted. Erase Protection When V PP = V IL, absolute hardware erase protection is provided for all device blocks. If VPP is at or below V PPLK, ERASE operations halt and SR3 is set indicating a V PP-level error. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Security Operations Security Operations Block Locking Individual instant block locking is used to protect user code and/or data within the flash memory array. All blocks power-up in a locked state to protect array data from being altered during power transitions. Any block can be locked or unlocked with no latency. Locked blocks cannot be programmed or erased; they can only be read. Software-controlled security is implemented using the BLOCK LOCK and BLOCK UNLOCK commands. Hardware-controlled security can be implemented using the BLOCK LOCK DOWN command along with asserting WP#. Also, V PP data security can be used to inhibit PROGRAM and ERASE operations. BLOCK LOCK Command To lock a block, issue the BLOCK LOCK SETUP command, followed by the BLOCK LOCK command issued to the desired block’s address. If the SET READ CONFIGURATION REGISTER command is issued after the BLOCK LOCK SETUP command, the device configures the RCR instead. BLOCK LOCK and UNLOCK operations are not affected by the voltage level on V PP. The block lock bits may be modified and/or read even if V PP is at or below V PPLK. BLOCK UNLOCK Command The BLOCK UNLOCK command is used to unlock blocks. Unlocked blocks can be read, programmed, and erased. Unlocked blocks return to a locked state when the device is reset or powered down. If a block is in a lock-down state, WP# must be de-asserted before it can be unlocked. BLOCK LOCK DOWN Command A locked or unlocked block can be locked-down by writing the BLOCK LOCK DOWN command sequence. Blocks in a lock-down state cannot be programmed or erased; they can only be read. However, unlike locked blocks, their locked state cannot be changed by software commands alone. A locked-down block can only be unlocked by issuing the BLOCK UNLOCK command with WP# de-asserted. To return an unlocked block to locked-down state, a BLOCK LOCK DOWN command must be issued prior to changing WP# to V IL. Locked-down blocks revert to the locked state upon reset or power up the device. Block Lock Status The READ DEVICE IDENTIFIER command is used to determine a block’s lock status. DQ[1:0] display the addressed block’s lock status; DQ0 is the addressed block’s lock bit, while DQ1 is the addressed block’s lock-down bit. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Security Operations Figure 9: Block Locking State Diagram [000] D0h 01h Program/Erase Allowed WP# = VIL = 0 [001] 2Fh 2Fh WP# toggle D0h, 01h, or 2Fh [010] (Virtual lock-down) [110] D0h Program/Erase Allowed WP# = VIH = 1 01h/2Fh (Power-up/ Reset default) [011] Program/Erase Prevented WP# = VIL = 0 (Locked down) WP# toggle [111] (Lock down disabled, WP# = VIH) 2Fh 2Fh [100] D0h 01h [101] Program/Erase Prevented WP# = VIH = 1 (Power-up/ Reset default) 1. D0h = UNLOCK command; 01h = LOCK command; 60h (not shown) LOCK SETUP command; 2Fh = LOCK DOWN command. Note: Block Locking During Suspend Block lock and unlock changes can be performed during an erase suspend. To change block locking during an ERASE operation, first issue the ERASE SUSPEND command. Monitor the status register until SR7 and SR6 are set, indicating the device is suspended and ready to accept another command. Next, write the desired lock command sequence to a block, which changes the lock state of that block. After completing BLOCK LOCK or BLOCK UNLOCK operations, resume the ERASE operation using the ERASE RESUME command. Note: A BLOCK LOCK SETUP command followed by any command other than BLOCK LOCK, BLOCK UNLOCK, or BLOCK LOCK DOWN produces a command sequence error and set SR4 and SR5. If a command sequence error occurs during an erase suspend, SR4 and SR5 remains set, even after the erase operation is resumed. Unless the Status Register is cleared using the CLEAR STATUS REGISTER command before resuming the ERASE operation, possible erase errors may be masked by the command sequence error. If a block is locked or locked-down during an erase suspend of the same block, the lock status bits change immediately. However, the ERASE operation completes when it is resumed. BLOCK LOCK operations cannot occur during a program suspend. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 35 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Security Operations Selectable OTP Blocks The OTP security feature on the device is backward-compatible to the earlier generation devices. Contact your local Micron representative for details about its implementation. Password Access The password access is a security enhancement offered on the device. This feature protects information stored in array blocks by preventing content alteration or reads until a valid 64-bit password is received. The password access may be combined with nonvolatile protection and/or volatile protection to create a multi-tiered solution. Contact your Micron sales office for further details concerning password access. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 36 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Status Register Status Register Read Status Register To read the status register, issue the READ STATUS REGISTER command at any address. Status register information is available at the address that the READ STATUS REGISTER, WORD PROGRAM, or BLOCK ERASE command is issued to. Status register data is automatically made available following a word program, block erase, or block lock command sequence. Reads from the device after any of these command sequences will output the devices status until another valid command is written (e.g. READ ARRAY command). The status register is read using single asynchronous mode or synchronous burst mode reads. Status register data is output on DQ[7:0], while 0x00 is output on DQ[15:8]. In asynchronous mode, the falling edge of OE# or CE# (whichever occurs first) updates and latches the status register contents. However, when reading the status register in synchronous burst mode, CE# or ADV# must be toggled to update status data. The device write status bit (SR7) provides the overall status of the device. SR[6:1] present status and error information about the PROGRAM, ERASE, SUSPEND, V PP, and BLOCK LOCK operations. Note: Reading the status register is a nonarray READ operation. When the operation occurs in asynchronous page mode, only the first data is valid and all subsequent data are undefined. When the operation occurs in synchronous burst mode, the same data word requested will be output on successive clock edges until the burst length requirements are satisfied. Table 12: Status Register Description Notes apply to entire table Bits Name Bit Settings Description 7 Device write status (DWS) 0 = Busy 1 = Ready Status bit: Indicates whether a PROGRAM or ERASE command cycle is in progress. 6 Erase Suspend Status (ESS) 0 = Not in effect 1 = In effect Status bit: Indicates whether an ERASE operation has been or is going to be suspended. Erase/Blank check status (ES) Program status (PS) 00 = PROGRAM/ERASE successful 01 = PROGRAM error 10 = ERASE/BLANK CHECK error 11 = Command sequence error Status/Error bit: Indicates whether an ERASE/ BLANK CHECK or PROGRAM operation was successful. When an error is returned, the operation is aborted. 3 VPP status (VPPS) 0 = Within limits 1 = Exceeded limits (VPP ≤ VPPLK) Status bit: Indicates whether a PROGRAM/ERASE operation is within acceptable voltage range limits. 2 Program suspend status (PSS) 0 = Not in effect 1 = In effect Status bit: Indicates whether a PROGRAM operation has been or is going to be suspended. 1 Block lock status (BLS) 0 = Not locked 1 = Locked (operation aborted) Status bit: Indicates whether a block is locked when a PROGRAM or ERASE operation is initiated. 0 BEFP status (BWS) 0 = BEFP complete 1 = BEFP in progress Status bit: Indicates whether BEFP data has completed loading into the buffer. 5:4 Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. Default value = 0x80. 2. Always clear the status register prior to resuming ERASE operations. This eliminates status register ambiguity when issuing commands during ERASE SUSPEND. If a command 37 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Status Register sequence error occurs during an ERASE SUSPEND, the status register contains the command sequence error status (SR[7,5,4] set). When the ERASE operation resumes and finishes, possible errors during the operation cannot be detected via the status register because it contains the previous error status. 3. When bits 5:4 indicate a PROGRAM/ERASE operation error, either a CLEAR STATUS REGISTER 50h) or a RESET command must be issued with a 15µs delay. Clear Status Register The CLEAR STATUS REGISTER command clears the status register. It functions independently of V PP. The device sets and clears SR[7,6,2], but it sets bits SR[5:3,1] without clearing them. The status register should be cleared before starting a command sequence to avoid any ambiguity. A device reset also clears the status register. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 38 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Configuration Register Configuration Register Read Configuration Register The read configuration register (RCR) is a 16-bit read/write register used to select bus read mode (synchronous or asynchronous) and to configure device synchronous burst read characteristics. To modify RCR settings, use the CONFIGURE READ CONFIGURATION REGISTER command. RCR contents can be examined using the READ DEVICE IDENTIFIER command and then reading from offset 0x05. On power-up or exit from reset, the RCR defaults to asynchronous mode. RCR bits are described in more detail below. Note: Reading the configuration register is a nonarray READ operation. When the operation occurs in asynchronous page mode, only the first data is valid, and all subsequent data are undefined. When the operation occurs in synchronous burst mode, the same word of data requested will be output on successive clock edges until the burst length requirements are satisfied. Table 13: Read Configuration Register Bits 15 Name Settings/Description Read mode (RM) 0 = Synchronous burst mode read 1 = Asynchronous page mode read (default) 14:11 Latency count (LC[3:0]) 0000 = Code 0 (reserved) 0001 = Code 1 (reserved) 0010 = Code 2 (reserved) 0011 = Code 3 0100 = Code 4 0101 = Code 5 0110 = Code 6 0111 = Code 7 1000 = Code 8 1001 = Code 9 1010 = Code 10 1011 = Code11 1100 = Code 12 1101 = Code 13 1110 = Code 14 1111 = Code 15 (default) 10 WAIT polarity (WP) 0 = WAIT signal is active LOW (default) 1 = WAIT signal is active HIGH 9 Reserved (R) Default 0, Nonchangeable 8 WAIT delay (WD) 0 = WAIT de-asserted with valid data 1 = WAIT de-asserted one data cycle before valid data (default) 7 Burst sequence (BS) Default 0, Nonchangeable 6 Clock edge (CE) 0 = Falling edge 1 = Rising edge (default) Reserved (R) Default 0, Nonchangeable Burst wrap (BW) 0 = Wrap; Burst accesses wrap within burst length set by BL[2:0] 1 = No Wrap; Burst accesses do not wrap within burst length (default) 5:4 3 2:0 Burst length (BL[2:0]) 001 = 4-word burst 010 = 8-word burst 011 = 16-word burst 111 = Continuous burst (default) (Other bit settings are reserved) Read Mode The read mode (RM) bit selects synchronous burst mode or asynchronous page mode operation for the device. When the RM bit is set, asynchronous page mode is selected (default). When RM is cleared, synchronous burst mode is selected. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 39 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Configuration Register Latency Count The latency count (LC) bits tell the device how many clock cycles must elapse from the rising edge of ADV# (or from the first valid clock edge after ADV# is asserted) until the first valid data word is driven to DQ[15:0]. The input clock frequency is used to determine this value. The First Access Latency Count figure shows the data output latency for different LC settings. Figure 10: First Access Latency Count CLK [C] Address [A] Valid Address ADV# [V] Code 0 (Reserved Valid Output DQ[15:0] [D/Q] Code 1 (Reserved ) DQ[15:0] [D/Q] Code DQ[15:0] [D/Q] DQ[15:0] [D/Q] DQ[15:0] [D/Q] DQ[15:0] [D/Q] DQ[15:0] [D/Q] Note: Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output 2 (Reserved ) DQ[15:0] [D/Q] ) Valid Output Code 3 Code 4 Code 5 Code 6 Code 7 Valid Output 1. First Access Latency Count Calculation: • 1 / CLK frequency = CLK period (ns) • n x (CLK period) ≥ tAVQV (ns) – tCHQV (ns) • Latency Count = n PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 40 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Configuration Register Figure 11: Example Latency Count Setting Using Code 3 0 1 2 3 tData 4 CLK CE# ADV# Address A[MAX:1] Code 3 High-Z D[15:0] Data R103 End of Wordline Considerations End of wordline (EOWL) wait states can result when the starting address of the burst operation is not aligned to a 16-word boundary; that is, A[4:1] of the start address does not equal 0x0. The figure below illustrates the end of wordline wait state(s) that occur after the first 16-word boundary is reached. The number of data words and wait states is summarized in the table below. Figure 12: End of Wordline Timing Diagram Latency Count CLK A[MAX:1] Address DQ[15:0] Data Data Data ADV# OE# EOWL WAIT# PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 41 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Configuration Register Table 14: End of Wordline Data and WAIT State Comparison 130nm 65nm Latency Count Data Words WAIT States Data Words WAIT States 1 Not Supported Not Supported Not Supported Not Supported 2 4 0 to 1 Not Supported Not Supported 3 4 0 to 2 Not Supported Not Supported 4 4 0 to 3 Not Supported Not Supported 5 4 0 to 4 16 0 to 4 6 4 0 to 5 16 0 to 5 7 4 0 to 6 16 0 to 6 8 Not Supported Not Supported 16 0 to 7 9 16 0 to 8 10 16 0 to 9 11 16 0 to 10 12 16 0 to 11 13 16 0 to 12 14 16 0 to 13 15 16 0 to 14 WAIT Signal Polarity and Functionality The WAIT polarity (WP) bit, RCR10 determines the asserted level (V OH or V OL) of WAIT. When WP is set, WAIT is asserted HIGH (default). When WP is cleared, WAIT is asserted LOW. The WAIT signal changes state on valid clock edges during active bus cycles (CE# asserted, OE# asserted, RST# de-asserted). The WAIT signal indicates data valid when the device is operating in synchronous mode (RCR15 = 0). The WAIT signal is only de-asserted when data is valid on the bus. When the device is operating in synchronous nonarray read mode, such as read status, read ID, or read CFI, the WAIT signal is also de-asserted when data is valid on the bus. WAIT behavior during synchronous nonarray reads at the end of wordline works correctly only on the first data access. When the device is operating in asynchronous page mode, asynchronous single word read mode, and all write operations, WAIT is set to a de-asserted state as determined by RCR10. Table 15: WAIT Functionality Table Condition WAIT Notes CE# = 1, OE# = X or CE# = 0, OE# = 1 High-Z 1 CE# = 0, OE# = 0 Active 1 Synchronous Array Reads Active 1 Synchronous Nonarray Reads Active 1 De-asserted 1 All Asynchronous Reads PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 42 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Configuration Register Table 15: WAIT Functionality Table (Continued) Condition WAIT Notes All Writes High-Z 1, 2 1. Active means that WAIT is asserted until data becomes valid, then deasserts. 2. When OE# = VIH during writes, WAIT = High-Z. Notes: WAIT Delay The WAIT delay (WD) bit controls the WAIT assertion delay behavior during synchronous burst reads. WAIT can be asserted either during or one data cycle before valid data is output on DQ[15:0]. When WD is set, WAIT is de-asserted one data cycle before valid data (default). When WD is cleared, WAIT is de-asserted during valid data. Burst Sequence The burst sequence (BS) bit selects linear burst sequence (default). Only linear burst sequence is supported. The synchronous burst sequence for all burst lengths, as well as the effect of the burst wrap (BW) setting are shown below. Table 16: Burst Sequence Word Ordering Burst Addressing Sequence (DEC) Start Address (DEC) Burst Wrap (RCR3) 4-Word Burst (BL[2:0] = 0b001) 8-Word Burst (BL[2:0] = 0b010) 16-Word Burst (BL[2:0] = 0b011) Continuous Burst (BL[2:0] = 0b111) 0 0 0-1-2-3 0-1-2-3-4-5-6-7 0-1-2-3-4…14-15 0-1-2-3-4-5-6-… 1 0 1-2-3-0 1-2-3-4-5-6-7-0 1-2-3-4-5…15-0 1-2-3-4-5-6-7-… 2 0 2-3-0-1 2-3-4-5-6-7-0-1 2-3-4-5-6…15-0-1 2-3-4-5-6-7-8-… 3 0 3-0-1-2 3-4-5-6-7-0-1-2 3-4-5-6-7…15-0-1-2 3-4-5-6-7-8-9-… 4 0 4-5-6-7-0-1-2-3 4-5-6-7-8…15-0-1-2-3 4-5-6-7-8-9-10… 5 0 5-6-7-0-1-2-3-4 5-6-7-8-9…15-0-1-2-3-4 5-6-7-8-9-10-11… 6 0 6-7-0-1-2-3-4-5 6-7-8-9-10…15-0-1-2-3-4-5 6-7-8-9-10-11-12-… 7 0 7-0-1-2-3-4-5-6 7-8-9-10…15-0-1-2-3-4-5-6 7-8-9-10-11-12-13… ⋮ ⋮ ⋮ ⋮ ⋮ 14 0 14-15-0-1-2…12-13 14-15-16-17-18-19-20-… 15 0 15-0-1-2-3…13-14 15-16-17-18-19-20-21-… ⋮ ⋮ ⋮ ⋮ ⋮ ⋮ 0 1 0-1-2-3 0-1-2-3-4-5-6-7 0-1-2-3-4…14-15 0-1-2-3-4-5-6-… 1 1 1-2-3-4 1-2-3-4-5-6-7-8 1-2-3-4-5…15-16 1-2-3-4-5-6-7-… 2 1 2-3-4-5 2-3-4-5-6-7-8-9 2-3-4-5-6…16-17 2-3-4-5-6-7-8-… 3 1 3-4-5-6 3-4-5-6-7-8-9-10 3-4-5-6-7…17-18 3-4-5-6-7-8-9-… PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN ⋮ 43 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Configuration Register Table 16: Burst Sequence Word Ordering (Continued) Burst Addressing Sequence (DEC) Start Address (DEC) Burst Wrap (RCR3) 4 5 4-Word Burst (BL[2:0] = 0b001) 8-Word Burst (BL[2:0] = 0b010) 16-Word Burst (BL[2:0] = 0b011) Continuous Burst (BL[2:0] = 0b111) 1 4-5-6-7-8-9-10-11 4-5-6-7-8…18-19 4-5-6-7-8-9-10… 1 5-6-7-8-9-10-11-12 5-6-7-8-9…19-20 5-6-7-8-9-10-11… 6 1 6-7-8-9-10-11-12-13 6-7-8-9-10…20-21 6-7-8-9-10-11-12-… 7 1 7-8-9-10-11-12-13-14 7-8-9-10-11…21-22 7-8-9-10-11-12-13… ⋮ ⋮ ⋮ ⋮ ⋮ 14 1 14-15-16-17-18…28-29 14-15-16-17-18-19-20-… 15 1 15-16-17-18-19…29-30 15-16-17-18-19-20-21-… ⋮ Clock Edge The clock edge (CE) bit selects either a rising (default) or falling clock edge for CLK. This clock edge is used at the start of a burst cycle to output synchronous data and to assert/de-assert WAIT. Burst Wrap The burst wrap (BW) bit determines whether 4-word, 8-word, or 16-word burst length accesses wrap within the selected word length boundaries or cross word length boundaries. When BW is set, burst wrapping does not occur (default). When BW is cleared, burst wrapping occurs. When performing synchronous burst reads with BW set (no wrap), an output delay may occur when the burst sequence crosses its first device row (16-word) boundary. If the burst sequence’s start address is 4-word aligned, then no delay occurs. If the start address is at the end of a 4-word boundary, the worst-case output delay is one clock cycle less than the first access latency count. This delay can take place only once and doesn’t occur if the burst sequence does not cross a device row boundary. WAIT informs the system of this delay when it occurs. Burst Length The burst length bits (BL[2:0]) select the linear burst length for all synchronous burst reads of the flash memory array. The burst lengths are 4-word, 8-word, 16-word, or continuous. Continuous burst accesses are linear only and do not wrap within any word length boundaries. When a burst cycle begins, the device outputs synchronous burst data until it reaches the end of the “burstable” address space. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 44 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm One-Time Programmable Registers One-Time Programmable Registers Read OTP Registers The device contains 17 OTP registers that can be used to implement system security measures and/or device identification. Each OTP register can be individually locked. The first 128-bit OTP register is comprised of two 64-bit (8-word) segments. The lower 64-bit segment is preprogrammed at the Micron factory with a unique 64-bit number. The upper 64-bit segment, as well as the other sixteen 128-bit OTP registers, are blank. Users can program them as needed. Once programmed, users can also lock the OTP register(s) to prevent additional bit programming (see the OTP Register Map figure below). The OTP registers contain OTP bits; when programmed, PR bits cannot be erased. Each OTP register can be accessed multiple times to program individual bits, as long as the register remains unlocked. Each OTP register has an associated lock register bit. When a lock register bit is programmed, the associated OTP register can only be read; it can no longer be programmed. Additionally, because the lock register bits themselves are OTP, when programmed, they cannot be erased. Therefore, when an OTP register is locked, it cannot be unlocked. The OTP registers can be read from an OTP-RA address. To read the OTP register, a READ DEVICE IDENTIFIER command is issued at an OTP-RA address to place the device in the read device identifier state. Next, a READ operation is performed using the address offset corresponding to the register to be read. The Device Identifier Information table shows the address offsets of the OTP registers and lock registers. PR data is read 16 bits at a time. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 45 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm One-Time Programmable Registers Figure 13: OTP Register Map 0x109 128-bit OTP Register 16 User Programmable 0x102 0x91 128-bit OTP Register 1 User Programmable 0x8A Lock Register 1 0x89 0x88 128-bit OTP Register 0 0x85 0x84 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 3 2 1 0 64-bit Segment User Programmable 64-bit Segment Factory Programed 0x81 Lock Register 0 0x80 15 14 13 12 11 10 9 8 7 6 5 4 Program OTP Registers To program an OTP register, a PROGRAM OTP REGISTER command is issued at the parameter’s base address plus the offset of the desired OTP register location. Next, the desired OTP register data is written to the same OTP register address. The device programs the 64-bit and 128-bit user-programmable OTP register data 16 bits at a time. Issuing the PROGRAM OTP REGISTER command outside of the OTP register’s address space causes a program error (SR4 set). Attempting to program a locked OTP register causes a program error (SR4 set) and a lock error (SR1 set). Lock OTP Registers Each OTP register can be locked by programming its respective lock bit in the lock register. The corresponding bit in the lock register is programmed by issuing the PROGRAM LOCK REGISTER command, followed by the desired lock register data. The physical addresses of the lock registers are 0x80 for register 0 and 0x89 for register 1; these addresses are used when programming the lock registers. Bit 0 of lock register 0 is programmed during the manufacturing process, locking the lower-half segment of the first 128-bit OTP register. Bit 1 of lock register 0, which corresponds to the upper-half segment of the first 128-bit OTP register, can be programmed by the user . When programming bit 1 of lock register 0, all other bits need to be left as 1 such that the data programmed is 0xFFFD. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 46 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm One-Time Programmable Registers Lock register 1 controls the the upper sixteen 128-bit OTP registers. Each bit of lock register 1 corresponds to a specific 128-bit OTP register. Programming a bit in lock register 1 locks the corresponding 128-bit OTP register; e.g., programming LR1.0 locks the corresponding OTP register 1. Note: Once locked, the OTP registers cannot be unlocked. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 47 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Common Flash Interface The CFI is part of an overall specification for multiple command-set and control-interface descriptions. System software can parse the CFI database structure to obtain information about the device, such as block size, density, bus width, and electrical specifications. The system software determines which command set to use to properly perform a WRITE command, a BLOCK ERASE or READ command, and to otherwise control the device. Information in the CFI database can be viewed by issuing the READ CFI command. READ CFI Structure Output The READ CFI command obtains CFI database structure information and always outputs it on the lower byte, DQ[7:0], for a word-wide (x16) device. This CFI-compliant device always outputs 00h data on the upper byte (DQ[15:8]). The numerical offset value is the address relative to the maximum bus width the device supports. For this device family, the starting address is a 10h, which is a word address for x16 devices. For example, at this starting address of 10h, a READ CFI command outputs an ASCII Q in the lower byte and 00h in the higher byte as shown here. In all the CFI tables shown here, address and data are represented in hexadecimal notation. In addition, because the upper byte of word-wide devices is always 00h, as shown in the example here, the leading 00 has been dropped and only the lower byte value is shown. Following is a table showing the CFI output for a x16 device, beginning at address 10h and a table showing an overview of the CFI database sections with their addresses. Table 17: Example of CFI Output (x16 device) as a Function of Device and Mode Device Hex Offset Hex Code ASCII Value (DQ[15:8]) ASCII Value (DQ[7:0]) Address 00010: 51 00 Q 00011: 52 00 R 00012: 59 00 Y Primary vendor ID 00013: P_IDLO 00 00014: P_IDHI 00 00015: PLO 00 00016: PHI 00 00017: A_IDLO 00 00018: A_IDHI 00 : : : : : : PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 48 Primary vendor table address Alternate vendor ID : : Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 18: CFI Database: Addresses and Sections Address 00001:Fh Section Name Description Reserved Reserved for vendor-specific information 00010h CFI ID string Flash device command set ID (identification) and vendor data offset 0001Bh System interface information Flash device timing and voltage 00027h Device geometry definition Flash device layout P Primary Micron-specific extended query Vendor-defined informaton specific to the primary vendor algorithm (offset 15 defines P which points to the primary Micron-specific extended query table.) Table 19: CFI ID String Hex Offset Length 10h 3 13h 2 Address Hex Code ASCII Value (DQ[7:0]) 10: - -51 Q 11: - -52 R 12: - -59 Y Primary vendor command set and control interface ID code. 16-bit ID code for vendor-specified algorithms. 13: - -01 Primary vendor ID number 14: - -00 Description Query unique ASCII string “QRY” 15h 2 Extended query table primary algorithm address. 15: - -0A 16: - -01 Primary vendor table address, primary algorithm 17h 2 Alternate vendor command set and control interface ID code. 0000h means no second vendor-specified algorithm exists. 17: - -00 Alternate vendor ID number 18: - -00 Secondary algorithm extended query table address. 0000h means none exists. 19: - -00 1A: - -00 19h 2 Note: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN Primary vendor table address, secondary algorithm 1. The CFI ID string provides verification that the device supports the CFI specification. It also indicates the specification version and supported vendor-specific command sets. 49 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 20: System Interface Information Hex Offset Length Description Address Hex Code ASCII Value (DQ[7:0]) 1Bh 1 VCC logic supply minimum program/erase voltage. bits 0 - 3 BCD 100 mV bits 4 - 7 BCD volts 1Bh - -23 2.3V 1Ch 1 VCC logic supply maximum program/erase voltage. bits 0 - 3 BCD 100 mV bits 4 - 7 BCD volts 1Ch - -36 3.6V 1Dh 1 VPP [programming] supply minimum program/ erase voltage. bits 0 - 3 BCD 100 mV bits 4 - 7 hex volts 1Dh - -85 8.5V 1Eh 1 VPP [programming] supply maximum program/ erase voltage. bits 0 - 3 BCD 100 mV bits 4 - 7 hex volts 1Eh - -95 9.5V 1Fh 1 “n” such that typical single word program timeout = 2n μs. 1Fh - -09 512µs 20h 1 “n” such that typical full buffer write timeout = 2n μs. 20h - -0A 1024µs 21h 1 “n” such that typical block erase timeout = 2n ms. 21h - -0A 1s 22h - -00 NA 2n 22h 1 “n” such that typical full chip erase timeout = ms. 23h 1 “n” such that maximum word program timeout = 2n times typical. 23h - -01 1024µs 24h 1 “n” such that maximum buffer write timeout = 2n times typical. 24h - -02 4096µs 25h 1 “n” such that maximum block erase timeout = 2n times typical. 25h - -02 4s 26h 1 “n” such that maximum chip erase timeout = 2n times typical. 26h - -00 NA PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 50 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 21: Device Geometry Hex Offset Length 27h 1 n such that device size in bytes = 2n. 27: 28h 2 Flash device interface code assignment: n such that n + 1 specifies the bit field that represents the flash device width capabilities as described here: bit 0: x8 bit 1: x16 bit 2: x32 bit 3: x64 bits 4 - 7: – bits 8 - 15: – 28: - -01 29: - -00 n such that maximum number of bytes in write buffer = 2n. 2Ah - -0A 2Bh - -00 2Ah 2 Description Address Hex Code ASCII Value (DQ[7:0]) See Note 1 x16 1024 2Ch 1 Number of erase block regions (x) within the device: 1) x = 0 means no erase blocking; the device erases in bulk. 2) x specifies the number of device regions with one or more contiguous, same-size erase blocks. 3) Symmetrically blocked partitions have one blocking region. 2Ch See Note 1 2Dh 4 Erase block region 1 information: bits 0 - 15 = y, y + 1 = number of identical-size erase blocks. bits 16 - 31 = z, region erase block(s) size are z x 256 bytes. 2D: 2E: 2F: 30: See Note 1 31h 4 Erase block region 2 information: bits 0 - 15 = y, y + 1 = number of identical-size erase blocks. bits 16 - 31 = z, region erase block(s) size are z x 256 bytes. 31: 32: 33: 34: See Note 1 35h 4 Reserved for future erase block region information. 35: 36: 37: 38: See Note 1 Note: 1. See Block Region Map Information table. Table 22: Block Region Map Information 512Mb 1Gb 2Gb Address Top Bottom Symmetrical Top Bottom Symmetrical Symmetrical 27: --1A --1A --1A --1B --1B --1B --1B 28: --01 --01 --01 --01 --01 --01 --01 29: --00 --00 --00 --00 --00 --00 --00 2A: --0A --0A --0A --0A --0A --0A --0A 2B: --00 --00 --00 --00 --00 --00 --00 2C: --02 --02 --01 --02 --02 --01 --01 2D: --FE --03 --FF --FE --03 --FF --FF PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 51 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 22: Block Region Map Information (Continued) 512Mb 1Gb 2Gb Address Top Bottom Symmetrical Top Bottom Symmetrical Symmetrical 2E: --01 --00 --01 --03 --00 --03 --03 2F: --00 --80 --00 --00 --80 --00 --00 30: --02 --00 --02 --02 --00 --02 --02 31: --03 --FE --00 --03 --FE --00 --00 32: --00 --01 --00 --00 --03 --00 --00 33: --80 --00 --00 --80 --00 --00 34: --00 --02 --00 --00 --02 --00 35:~38: --00 --00 --00 --00 --00 --00 Table 23: Primary Vendor-Specific Extended Query Hex Offset P = 10Ah Length Description Primary extended query table, unique ASCII string: PRI Address Hex Code ASCII Value (DQ[7:0]) 10A: - -50 P 10B: - -52 R 10C: - -49 I (P+0)h (P+1)h (P+2)h 3 (P+3)h 1 Major version number, ASCII 10D: - -31 1 (P+4)h 1 Minor version number, ASCII 10E: - -35 5 PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 52 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 23: Primary Vendor-Specific Extended Query (Continued) Hex Offset P = 10Ah (P+5)h (P+6)h (P+7)h (P+8)h Length Description Address Hex Code ASCII Value (DQ[7:0]) 4 Optional feature and command support (1 = yes; 0 = no) Bits 11 - 29 are reserved; undefined bits are 0 If bit 31 = 1, then another 31-bit field of optional features follows at the end of the bit 30 field. 10F: - -E6 – 110: - -01 – 111: - -00 – 112: See Note 1 – Bit 0: Chip erase supported. bit 0 = 0 No Bit 1: Suspend erase supported. bit 1 = 1 Yes Bit 2: Suspend program supported. bit 2 = 1 Yes Bit 3: Legacy lock/unlock supported. bit 3 = 0 No Bit 4: Queued erase supported. bit 4 = 0 No Bit 5: Instant individual block locking supported. bit 5 = 1 Yes Bit 6: OTP bits supported. bit 6 = 1 Yes Bit 7: Page mode read supported. bit 7 = 1 Yes Bit 8: Synchronous read supported. bit 8 = 1 Yes Bit 9: Simultaneous operations supported. bit 9 = 0 No Bit 10: Extended Flash array block supported. bit 10 = 0 No Bit 11: Permanent block locking of up to full main array supported. bit 11 = 0 Yes Bit 12: Permanent block locking of up to partial main array supported. bit 12 = 0 No bit 30 See Note 1 Bit 30: CFI links to follow: Bit 31: Another optional features field to follow. (P+9)h 1 Supported functions after SUSPEND: READ ARRAY, STATUS, QUERY. Other supported options include: Bits 1 - 7: Reserved; undefined bits are 0. bit 31 113: Bit 0: Program supported after ERASE SUSPEND. (P+A)h (P+B)h 2 Block Status Register mask: Bits 2 - 15 are reserved; undefined bits are 0. bit 0 = 1 114: 1 Yes - -03 115: – - -00 – – Bit 0: Block lock-bit status register active. bit 0 = 1 Yes Bit 1: Block lock-down bit status active. bit 1 = 1 Yes Bit 4: EFA block lock-bit status register active. bit 4 = 0 No Bit 5: EFA block lock-bit status active. (P+C)h - -01 bit 5 = 0 VCC logic supply highest performance program/ erase voltage. bits 0 - 3 BCD 100 mV bits 4 - 7 hex value in volts PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 53 116: No - -30 3.0V Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 23: Primary Vendor-Specific Extended Query (Continued) Hex Offset P = 10Ah Length (P+D)h 1 Description Address Hex Code ASCII Value (DQ[7:0]) 117: - -90 9.0V VPP optimum program/erase voltage. bits 0 - 3 BCD 100mV bits 4 - 7 hex value in volts 1. See Optional Features Fields table. Note: Table 24: Optional Features Field Discrete Address 2Gb Bottom Top – – die 1 (B) die 2 (T) die 1 (T) die 2 (B) --00 --00 40: --00 --40 --00 112: Bottom Top Table 25: One Time Programmable (OTP) Space Information Hex Offset P = 10Ah Length (P+E)h 1 (P+F)h (P+10)h (P+11)h (P+12)h 4 Description Number of OTP block fields in JEDEC ID space. 00h indicates that 256 OTP fields are available. OTP Field 1: OTP Description: This field describes user-available OTP bytes. Some are preprogrammed with device-unique serial numbers. Others are user-programmable. Bits 0-15 point to the OTP Lock byte (the first byte). The following bytes are factory preprogrammed and user-programmable: Bits 0 - 7 = Lock/bytes JEDEC plane physical low address. Bits 8 - 15 = Lock/bytes JEDEC plane physical high address. Bits 16 - 23 = n where 2n equals factory preprogrammed bytes. Bits 24 - 31 = n where 2n equals user-programmable bytes. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 54 Address Hex Code ASCII Value (DQ[7:0]) 118: - -02 2 119: - -80 80h 11A: - -00 00h 1B: - -03 8 byte 11C: - -03 8 byte Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 25: One Time Programmable (OTP) Space Information (Continued) Hex Offset P = 10Ah Length Description Address Hex Code ASCII Value (DQ[7:0]) 10 Protection field 2: protection description Bits 0 - 31 point to the protection register physical lock word address in the JEDEC plane. The bytes that follow are factory or user-progammable. 11D: - -89 89h 11E: - -00 00h 11F: - -00 00h 120: - -00 00h (P+17)h (P+18)h (P+19)h Bits 32 - 39 = n where n equals factory programmed groups (low byte). Bits 40 - 47 = n where n equals factory programmed groups (high byte). Bits 48 - 55 = n where 2n equals factory programmed bytes/groups. 121: - -00 0 122: - -00 0 123: - -00 0 (P+1A)h (P+1B)h (P+1C)h Bits 56 - 63 = n where n equals user programmed groups (low byte). Bits 64 - 71 = n where n equals user programmed groups (high byte). Bits 72 - 79 = n where 2n equals user programmable bytes/groups. 124: - -10 16 125: - -00 0 126: - -04 16 (P+13)h (P+14)h (P+15)h (P+16)h Table 26: Burst Read Information Hex Offset P = 10Ah Length Description Address Hex Code ASCII Value (DQ[7:0]) 1 Page Mode Read capability: Bits 7 - 0 = n where 2n hex value represents the number of read-page bytes. See offset 28h for device word width to determine page-mode data output width. 00h indicates no read page buffer. 127: - -05 32 byte 1 Number of synchronous mode read configuration fields that follow. 00h indicates no burst capability. 128: - -04 (P+1D)h (P+1E)h PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 55 4 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 26: Burst Read Information (Continued) Hex Offset P = 10Ah Length Description Address Hex Code 1 Synchronous mode read capability configuration 1: Bits 3 - 7 = Reserved. Bits 0 - 2 = n where 2n+1 hex value represents the maximum number of continuous synchronous reads when the device is configured for its maximum word width. A value of 07h indicates that the device is capable of continuous linear bursts that will output data until the internal burst counter reaches the end of the device’s burstable address space. This fields’s 3-bit value can be written directly to the Read Configuration Register bits 0 - 2 if the device is configured for its maximum word width. See offset 28h for word width to determine the burst data output width. 129: - -01 1 Synchronous mode read capability configuration 2. 12A: - -02 8 1 Synchronous mode read capability configuration 3. 12B: - -03 16 1 Synchronous mode read capability configuration 4. 12C: - -07 Continued (P+1F)h (P+20)h (P+21)h (P+22) ASCII Value (DQ[7:0]) 4 Table 27: Partition and Block Erase Region Information Hex Offset P = 10Ah Bottom Top (P+23)h (P+23)h PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN Description Optional Flash features and commands Number of device hardware-partition regions within the device: x = 0: a single hardware partition device (no fields follow). x specifies the number of device partition regions containing one or more contiguous erase block regions 56 Address Length Bottom Top 1 12D: 12D: Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 28: Partition Region 1 Information: Top and Bottom Offset/Address Hex Offset P = 10Ah Description Optional Flash features and commands Bottom Top (P+24)h (P+25)h (P+24)h (P+25)h (P+26)h (P+27)h Address Length Bottom Top Data size of this Partition Region information field (number of addressable locations, including this field. 2 12E: 12E: 12F: 12F: (P+26)h (P+27)h Number of identical partitions within the partition region. 2 130: 130: 131: 131: (P+28)h (P+28)h Number of program or erase operations allowed in a partition: Bits 0 - 3 = Number of simultaneous program operations. Bits 4 - 7 = Number of simultaneous erase operations. 1 132: 132: (P+29)h (P+29)h Simultaneous program or erase operations allowed in other partitions while a partition in this region is in program mode: Bits 0 - 3 = Number of simultaneous program operations. Bits 4 - 7 = Number of simultaneous erase operations. 1 133: 133: (P+2A)h (P+2A)h Simultaneous program or erase operations allowed in other partitions while a partition in this region is in erase mode: Bits 0 - 3 = Number of simultaneous program operations. Bits 4 - 7 = Number of simultaneous erase operations. 1 134: 134: (P+2B)h (P+2B)h Types of erase block regions in this partition region: x=0: No erase blocking; the partition region erases in bulk. x = Number of erase block regions with contiguous, same-size erase blocks. Symmetrically blocked partitions have one blocking region. Partition size = (Type 1 blocks) x (Type 1 block sizes) + (Type 2 blocks) x (Type 2 block sizes) +...+ (Type n blocks) x (Type n block sizes). 1 135: 135: Table 29: Partition Region 1 Information Hex Offset P = 10Ah Bottom/Top (P+2C)h (P+2D)h (P+2E)h (P+2F)h Description Optional Flash features and commands Partition region 1 erase block type 1 information: Bits 0-15 = y, y+1 = Number of identical-sized erase blocks in a partition. Bits 16-31 = z, where region erase block(s) size is z x 256 bytes. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 57 Length Address Bottom/Top 4 136: 137: 138: 139: Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 29: Partition Region 1 Information (Continued) Hex Offset P = 10Ah Bottom/Top Description Optional Flash features and commands Length Address Bottom/Top 13A: (P+30)h (P+31)h Partition 1 (erase block type 1): Minimum block erase cycles x 1000 2 (P+32)h Partition 1 (erase block type 1) bits per cell; internal ECC: Bits 0 - 3 = bits per cell in erase region Bit 4 = reserved for “internal ECC used” (1=yes, 0=no) Bit 5 - 7 = reserved for future use 1 13C: (P+33)h Partition 1 (erase block type 1) page mode and synchronous mode capabilities: Bits 0 = page-mode host reads permitted (1=yes, 0=no) Bit 1 = synchronous host reads permitted (1=yes, 0=no) Bit 2 = synchronous host writes permitted (1=yes, 0=no) Bit 3 - 7 = reserved for future use 1 13D: (P+34)h (P+35)h (P+36)h (P+37)h (P+38)h (P+39)h Partition 1 (erase block type 1) programming region information: Bits 0 - 7 = x, 2x: programming region aligned size (bytes) Bit 8-14 = reserved for future use Bit 15 = legacy flash operation; ignore 0:7 Bit 16 - 23 = y: control mode valid size (bytes) Bit 24 - 31 = reserved for future use Bit 32 - 39 = z: control mode invalid size (bytes) Bit 40 - 46 = reserved for future use Bit 47 = legacy flash operation (ignore 23:16 and 39:32) 6 13E: (P+3A)h (P+3B)h (P+3C)h (P+3D)h Partition 1 erase block type 2 information: Bits 0-15 = y, y+1 = Number of identical-size erase blocks in a partition. Bits 16 - 31 = z, where region erase block(s) size is z x 256 bytes. (bottom parameter device only) 4 (P+3E)h (P+3F)h Partition 1 (erase block type 2) Minimum block erase cycles x 1000 2 148: (P+40)h Partition 1 (erase block type 2) bits per cell, internal EDAC: Bits 0 - 3 = bits per cell in erase region Bit 4 = reserved for “internal ECC used” (1=yes, 0=no) Bits 5 - 7 = reserved for future use 1 14A: (P+41)h Partition 1 (erase block type 2) page mode and synchronous mode capabilities: Bit 0 = page-mode host reads permitted (1=yes, 0=no) Bit 1 = synchronous host reads permitted (1=yes, 0=no) Bit 2 = synchronous host writes permitted (1=yes, 0=no) Bits 3-7 = reserved for future use 1 14B: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 13B: 13F: 140: 141: 142: 143: 144: 145: 146: 147: 149: 58 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 29: Partition Region 1 Information (Continued) Hex Offset P = 10Ah Bottom/Top (P+42)h (P+43)h (P+44)h (P+45)h (P+46)h (P+47)h Description Optional Flash features and commands Partition 1 (erase block type 2) programming region information: Bits 0-7 = x, 2nx = Programming region aligned size (bytes) Bits 8-14 = reserved for future use Bit 15 = legacy flash operation (ignore 0:7) Bits 16 - 23 = y = Control mode valid size in bytes Bits 24 - 31 = reserved Bits 32 - 39 = z = Control mode invalid size in bytes Bits 40 - 46 = reserved Bit 47 = legacy flash operation (ignore 23:16 and 39:32) PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 59 Length Address Bottom/Top 6 14C: 14D: 14E: 14F: 150: 151: Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 30: Partition Region 1: Partition and Erase Block Map Information Add. 512Mb 1Gb 2Gb Top Bottom Symm. Top Bottom Symm. Symm. Upper Die Symm. Lower Die 12D: --01 --01 --01 --01 --01 --01 --01 --01 12E: --24 --24 --14 --24 --24 --14 --14 --14 12F: --00 --00 --00 --00 --00 --00 --00 --00 130: --01 --01 --01 --01 --01 --01 --01 --01 131: --00 --00 --00 --00 --00 --00 --00 --00 132: --11 --11 --11 --11 --11 --11 --11 --11 133: --00 --00 --00 --00 --00 --00 --00 --00 134: --00 --00 --00 --00 --00 --00 --00 --00 135: --02 --02 --01 --02 --02 --01 --01 --01 136: --FE --03 --FF --FE --03 --FF --FF --FF 137: --01 --00 --01 --03 --00 --03 --03 --03 138: --00 --80 --00 --00 --80 --00 --00 --00 139: --02 --00 --02 --02 --00 --02 --02 --02 13A: --64 --64 --64 --64 --64 --64 --64 --64 13B: --00 --00 --00 --00 --00 --00 --00 --00 13C: --02 --02 --02 --02 --02 --02 --02 --02 13D*: --03 --03 --03 --03 --03 --03 --03 --03 13E: --00 --00 --00 --00 --00 --00 --00 --00 13F: --80 --80 --80 --80 --80 --80 --80 --80 140: --00 --00 --00 --00 --00 --00 --00 --00 141: --00 --00 --00 --00 --00 --00 --00 --00 142: --00 --00 --00 --00 --00 --00 --00 --00 143: --80 --80 --80 --80 --80 --80 --80 --80 144: --03 --FE --FF --03 --FE --FF --FF --10 145: --00 --01 --FF --00 --03 --FF --FF --C8 146: --80 --00 --FF --80 --00 --FF --FF --00 147: --00 --02 --FF --00 --02 --FF --FF --00 148: --64 --64 --FF --64 --64 --FF --FF --10 149: --00 --00 --FF --00 --00 --FF --FF --FF 14A: --02 --02 --FF --02 --02 --FF --FF --FF 14B: --03 --03 --FF --03 --03 --FF --FF --FF 14C: --00 --00 --FF --00 --00 --FF --FF --FF 14D: --80 --80 --FF --80 --80 --FF --FF --FF 14E: --00 --00 --FF --00 --00 --FF --FF --FF 14F: --00 --00 --FF --00 --00 --FF --FF --FF 150: --00 --00 --FF --00 --00 --FF --FF --FF PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 60 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Common Flash Interface Table 30: Partition Region 1: Partition and Erase Block Map Information (Continued) Add. 151: 512Mb 1Gb 2Gb Top Bottom Symm. Top Bottom Symm. Symm. Upper Die --80 --80 --FF --80 --80 --FF --FF Symm. Lower Die --FF Table 31: CFI Link Information – 2Gb Length Description Address 4 CFI Link field bit definitions: Bits 0 - 9 = Address offset (within 32Mb segment of referenced CFI table) Bits 10 - 27 = nth 32Mb segment of referenced CFI table Bits 28 - 30 = Memory Type Bit 31 = Another CFI link field immediately follows 144: 145: 146: 147 1 CFI Link field quantity subfield definitions: Bits 0 - 3 = Quantity field (n such that n+1 equals quantity) Bit 4 = Table and die relative location Bit 5 = Link field and table relative location Bits 6 - 7 = Reserved 148: Note: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN ASCII Value (DQ[7:0]) See Note 1 1. See "Partition Region 1: Partition and Erase Block Map Information" table. 61 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Flowcharts Figure 14: Word Program Procedure Start Command Cycle - Issue PROGRAM command - Address = location to program - Data = 0x40 Data Cycle - Address = location to program - Data = data to program Check Ready Status - READ STATUS REGISTER command not required - Perform READ operation - Read ready status on signal D7 No No D7 = 1? No Suspend? Yes Yes Program suspend (See Suspend/Resume Flowchart Errors? Yes Read Status Register - Toggle CE# or OE# to update status register - See Status Register Flowchart Error-handler user-defined routine Progam complete PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 62 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 15: Buffer Program Procedure Start X=X+1 Write buffer data, start address Device supports buffer writes? No Use single word programming Write buffer data, (at block address) within buffer range X=0 No Yes X=N Set timeout or loop counter No Abort bufferred program ? Yes Yes Get next target address Write confirm D0h (at block address) Issue WRITE-to-BUFFER command E8h (at block address) Read status register (at block address) CE# and OE# LOW updates status register SR7? 1 = Ready 0 = Busy Read status register SR7 = Valid (at block address ) Write to another block address No 0 Suspend program Yes Buffered program aborted Suspend program loop 1 No Device ready? SR7 = 0/1 0 = No Timeout or count expired? Full status check (if desired) Yes Another buffered programming ? 1 = Yes Write word count (N-1) N = 0 corresponds to count = 1 (at block address) Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN Yes No Program complete 1. Word count values on DQ0:DQ15 are loaded into the count register. Count ranges for this device are N = 0000h to 01FFh. 2. Device outputs the status register when read. 3. Write buffer contents will be programmed at the device start or destination address. 4. Align the start address on a write buffer boundary for maximum programming performance; that is, A[9:1] of the start address = 0). 5. Device aborts the BUFFERED PROGRAM command if the current address is outside the original block address. 6. Status register indicates an improper command sequence if the BUFFERED PROGRAM command is aborted. Follow this with a CLEAR STATUS REGISTER command. 7. Device defaults to SR output data after BUFFERED PROGRAMMING SETUP command (E8h) is issued . CE# or OE# must be toggled to update the status register . Don’t issue the READ SR command (70h); it is interpreted by the device as buffer word count. 8. Full status check can be done after erase and write sequences complete. Write FFh after the last operation to reset the device to read array mode. 63 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 16: Buffered Enhanced Factory Programming (BEFP) Procedure Setup Phase Program and Verify Phase Start Read status register Issue BEFP SETUP Data = 0x80 Buffer ready? Exit Phase Read status register No (SR0 = 1) Yes (SR0 = 0) Issue BEFP CONFIRM Data = 00D0h Buffer full? Read status register No (SR7 = 0) Yes (SR7 = 1) Full status register check for errors Write data word to buffer BEFP setup delay BEFP exited? No Finish Yes Read status register BEFP setup done? Yes (SR7 = 0) No (SR0 = 1) Program done? No (SR7 = 1) SR error-handler user-defined Yes (SR0 = 0) Yes Exit Program more data ? No Write 0xFFFF outside block PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 64 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 17: Block Erase Procedure Start Command Cycle - Issue ERASE command - Address = block to be erased - Data = 0x20 Confirm Cycle - Issue CONFIRM command - Address = block to be erased - Data = erase confirm (0xD0) Check Ready Status - READ STATUS REGISTER command not required - Perform READ operation - Read ready status on SR7 No SR7 = 1? No Suspend? No Yes Erase Suspend See Suspend/ Resume Flowchart Errors? Yes Yes Read Status Register - Toggle CE# or OE# to update status register - See Status Register Flowchart Error Handler user-defined routine End PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 65 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 18: Program Suspend/Resume Procedure Start Read SR2 = 1 = Suspended 0 = Completed Status Write 70h Any Address Read Program Suspend Program Completed 1 Array Write FFh Any Address Write B0h Any Address Read Status Register Initiate Read cycle to update the status register (Address = Block to suspend) SR7 = 1 = Ready 0 = Busy 0 Read Array Data from a block other than from the one being programmed Done Reading 0 Program 1 Yes Resume No Read Array Write D0h Any Address Write FFh Program Resumed Read Array Data Read Status Write 70h Any Address PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 66 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 19: Erase Suspend/Resume Procedure SR6 = 1 = Suspended 0 = Completed Start Read Status Erase Completed 1 Write 70h Any Address Read Program Read/Program? (FFh/40h) Read Array Data from Program Loop: to a a block other than the block other than the No one being erased one being erased Erase Suspend Write B0h Any Address Address = X Read Status Register Toggle CE#/OE# to update the status register SR7 = 1 = Ready 0 = Busy 0 Done? Yes Erase Resume 0 Read 1 Array Write D0h Any Address Write FFh Erase 1 Resumed Read Array Data Read Status Write 70h Any Address Note: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. The tERS/SUSP timing between the initial BLOCK ERASE or ERASE RESUME command and a subsequent ERASE SUSPEND command should be followed. 67 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 20: Block Lock Operations Procedure Start Lock Setup Write 60h Block Address Lock Confirm Write 01h, D0h, 2Fh Block Address Read ID Plane Write 90h Optional Read Block Lock Status No Locking Change? Read Yes Array Write FFh Any Address Lock Change Complete PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 68 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 21: OTP Register Programming Procedure Start OTP Program Setup - Write 0xC0 - OTP Address Confirm Data - Write OTP Address and Data Check Ready Status - READ STATUS REGISTER command not required - Perform READ operation - Read ready status on SR7 SR7 = 1? No Yes Read Status Register - Toggle CE# or OE# to update status register - See Status Register Flowchart End PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 69 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Flowcharts Figure 22: Status Register Procedure Start Command Cycle - Issue STATUS REGISTER command - Address = any device address - Data = 0x70 Data Cycle - Read Status Register SR[7:0] SR7 = 1 No Set/Reset by device Yes SR6 = 1 Yes Erase Suspend See Suspend/ Resume Flowchart Yes Program Suspend See Suspend/ Resume Flowchart No SR2 = 1 No SR5 = 1 Yes No SR4 = 1 Error Command sequence Yes Error Erase failure - Set by device - Reset by user - See Clear Status Register Command No SR4 = 1 Yes Error Program failure Yes Error VPEN/VPP < VPENLK/VPPLK Yes Error Block locked No SR3 = 1 No SR1 = 1 No End PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 70 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Power and Reset Specifications Power and Reset Specifications VCC should attain V CCmin from V SS simultaneously with or before applying V CCQ, V PP during power up. V CC should attain V SS during power down. Device inputs should not be driven before supply voltage = V CCmin. Power supply transitions should only occur when RST# is LOW. This protects the device from accidental programming or erasure during power transitions. Asserting RST# during a system reset is important with automated program/erase devices because systems typically expect to read from the device when coming out of reset. If a CPU reset occurs without a device reset, proper CPU initialization may not occur. This is because the device may be providing status information, instead of array data as expected. Connect RST# to the same active LOW reset signal used for CPU initialization. Because the device is disabled when RST# is asserted, it ignores its control inputs during power-up/down. Invalid bus conditions are masked, providing a level of memory protection. Table 32: Power and Reset Parameter Symbol Min Max Unit Notes RST# pulse width LOW tPLPH 100 – ns 1, 2, 3, 4 RST# LOW to device reset during erase tPLPH – 25 us 1, 3, 4, 7 – 25 1, 3, 4, 7 300 – 1, 4, 5, 6 RST# LOW to device reset during program tVCCPH VCC Power valid to RST# de-assertion (HIGH) Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 1. 2. 3. 4. 5. These specifications are valid for all device versions (packages and speeds). The device may reset if tPLPH is < tPLPH MIN, but this is not guaranteed. Not applicable if RST# is tied to VCC. Sampled, but not 100% tested. When RST# is tied to the VCC supply, device will not be ready until tVCCPH after VCC ≥ VCCMIN. 6. When RST# is tied to the VCCQ supply, device will not be ready until tVCCPH after VCC ≥ VCCMIN. 7. Reset completes within tPLPH if RST# is asserted while no ERASE or PROGRAM operation is executing. 71 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Power and Reset Specifications Figure 23: Reset Operation Waveforms tPLPH (A) Reset during read mode RST# tPHQV VIH VIL Abort complete tPLRH (B) Reset during program or block erase P1 ≤ P2 RST# VIH VIL tPLRH (C) Reset during program or block erase P1 ≥ P2 RST# tPHQV VIH Abort complete tPHQV VIL tVCCPH (D) VCC power-up to RST# HIGH VCC VCC 0V Power Supply Decoupling The device requires careful power supply de-coupling. Three basic power supply current considerations are 1) standby current levels, 2) active current levels, and 3) transient peaks produced when CE# and OE# are asserted and de-asserted. When the device is accessed, internal conditions change. Circuits within the device enable charge pumps, and internal logic states change at high speed. These internal activities produce transient signals. Transient current magnitudes depend on the device outputs’ capacitive and inductive loading. Two-line control and correct de-coupling capacitor selection suppress transient voltage peaks. Because the devices draw their power from V CC, V PP, and V CCQ, each power connection should have a 0.1µF and a 0.01µF ceramic capacitor to ground. High-frequency, inherently low-inductance capacitors should be placed as close as possible to package leads. Additionally, for every eight devices used in the system, a 4.7µF electrolytic capacitor should be placed between power and ground close to the devices. The bulk capacitor is meant to overcome voltage droop caused by PCB trace inductance. PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 72 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm Maximum Ratings and Operating Conditions Maximum Ratings and Operating Conditions Stresses greater than those listed can cause permanent damage to the device. This is stress rating only, and functional operation of the device at these or any other conditions above those indicated is not guaranteed. Table 33: Maximum Ratings Parameter Maximum Rating Temperature under bias –40°C to + 85 °C Storage temperature –65°C to + 125 °C Notes Voltage on any signal (except VCC, VPP, and VCCQ) –2V to +5.6V 1 VPP voltage –2V to +11.5V 1, 2 VCC voltage –2V to +5.6V 1 VCCQ voltage –2V to +5.6V 1 100mA 3 Output short circuit current Notes: 1. Voltages shown are specified with respect to VSS. During infrequent nonperiodic transitions, the level may undershoot to –2V for periods less than 20ns or overshoot to VCC + 2V or VCCQ + 2V or VPP + 2V for periods less than 20ns. 2. Program/erase voltage is typically 2.3–3.6V. 9.0V can be applied for 80 hours maximum total, to any blocks for 1000 cycles maximum. 9.0V program/erase voltage may reduce block cycling capability. 3. Output is shorted for no more than one second, and more than one output is not shorted at one time. Table 34: Operating Conditions Symbol Parameter Min Max Unit Notes 1 TA Operating temperature –40 +85 °C VCC VCC supply voltage 2.3 3.6 V VCCQ I/O supply voltage CMOS inputs 2.3 3.6 TTL inputs 2.4 3.6 VPPL VPP voltage supply (logic level) 1.5 3.6 VPPH Buffered enhanced factory programming VPP 8.5 9.5 tPPH Maximum VPP hours VPP = VPPH – 80 Hours VPP = VPPL 100,000 – Cycles VPP = VPPH – 1000 BLOCK Array blocks ERASE cycles Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 2 1. TA = ambient temperature. 2. In typical operation, VPP program voltage is VPPL. 73 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm DC Electrical Specifications DC Electrical Specifications Table 35: DC Current Characteristics CMOS Inputs (VCCQ = 2.3– 3.6V) Parameter TTL Inputs (VCCQ = 2.4– 3.6V) Symbol Typ Max Typ Max ILI – ±1 – ±2 – ±2 – ±4 – ±1 – ±10 – ±2 – ±20 70 225 70 225 75 240 75 240 150 480 150 480 26 31 26 31 12 16 12 16 19 22 19 22 Page mode read f = 13 MHz (17 CLK) 16 18 16 18 Synchronous burst f = 52 MHz, LC = 4 21 24 21 24 mA Continuous read 35 50 35 50 mA VPP = VPPL, program/erase in progress 1, 3, 5 35 50 35 50 VPP = VPPH, program/erase in progress 1, 3, 5 ICCWS, ICCES 70 225 70 225 µA CE# = VCCQ, suspend in progress 1, 3, 4 75 240 75 240 IPPS 0.2 5 0.2 5 µA 1, 3, 7 1Gb 0.2 5 0.2 5 VPP = VPPL, in standby mode 2Gb 0.4 10 0.4 10 0.2 5 0.2 5 µA VPP = VPPL, suspend in progress 1, 3, 7 VPP = VPPL Input load current 512Mb 1Gb 2Gb Output leakage current DQ[15:0], WAIT 512Mb 1Gb VCC standby, power-down 512Mb ILO 2Gb 1Gb ICCS, ICCD 2Gb Average Asynchronous VCC read single-word current f = 5 MHz (1 CLK) VCC program current, VCC erase current VCC program suspend current, VCC erase suspend current 512Mb 1Gb 2Gb VPP standby current 512Mb VPP program suspend current, VPP erase suspend current ICCR ICCW, ICCE Unit Test Conditions µA VCC = VCC (MAX) VCCQ = VCCQ (MAX) VIN = VCCQ or VSS µA VCC = VCC (MAX) VCCQ = VCCQ (MAX) VIN = VCCQ or VSS µA VCC = VCC (MAX) VCCQ = VCCQ (MAX) CE# = VCCQ RST# = VCCQ (for ICCS) RST# = VSS (for ICCD) WP# = VIH mA 16-word read VCC = VCC (MAX) mA 16-word read CE# = VIL OE# = VIH mA 8-word read Inputs: mA 16-word read V or V IL IH IPPWS, IPPES VPP read IPPR 2 15 2 15 µA VPP program current IPPW 0.05 0.1 0.05 0.1 mA VPP = VPPL, program in progress 0.05 0.1 0.05 0.1 VPP = VPPH, program in progress PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN 74 Notes 1, 6 1. 2 1 1, 3 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm DC Electrical Specifications Table 35: DC Current Characteristics (Continued) CMOS Inputs (VCCQ = 2.3– 3.6V) Parameter Symbol Typ Max Typ Max IPPE 0.05 0.1 0.05 0.1 mA VPP = VPPL, erase in progress 0.05 0.1 0.05 0.1 VPP = VPPH, erase in progress 0.05 0.1 0.05 0.1 mA VPP = VPPL 0.05 0.1 0.05 0.1 VPP = VPPH VPP erase current VPP blank check IPPBC Notes: TTL Inputs (VCCQ = 2.4– 3.6V) Unit Test Conditions Notes 3 3 1. All currents are RMS unless noted. Typical values at TYP VCC, TC = +25°C. 2. ICCS is the average current measured over any 5ms time interval 5µs after CE# is de-asserted. 3. Sampled, not 100% tested. 4. ICCES is specified with the device deselected. If device is read while in erase suspend, current is ICCES plus ICCR. 5. ICCW, ICCE measured over TYP or MAX times specified in (page 0 ). 6. if VIN > VCC, the input load current increases to 10µA MAX. 7. the IPPS,IPPWS,IPPES will increase to 200µA when VPP/WP# is at VPPH. Table 36: DC Voltage Characteristics CMOS Inputs (VCCQ = 2.3–3.6V) Parameter TTL Inputs1 (VCCQ = 2.4–3.6V) Symbol Min Max Min Max Input low voltage VIL –0.5 0.4 –0.5 0.6 V Input high voltage VIH VCCQ - 0.4 VCCQ + 0.5 2 VCCQ + 0.5 V Output low voltage VOL – 0.2 – 0.2 V VCC = VCC (MIN) VCCQ = VCCQ (MIN) IOL = 100µA Output high voltage VOH VCCQ - 0.2 – VCCQ – 0.2 – V VCC = VCC (MIN) VCCQ = VCCQ (MIN) IOH = –100µA VPP lock out voltage VPPLK – 0.4 – 0.4 V Notes: PDF: 09005aef845667b8 p33_65nm_MLC_512Mb-1gb_2gb.pdf - Rev. C 12/13 EN Unit Test Conditions Notes 2 3 1. Synchronous read mode is not supported with TTL inputs. 2. VIL can undershoot to –1.0V for durations of 2ns or less and VIH can overshoot to VCCQ + 1.0V for durations of 2ns or less. 3. VPP ≤ VPPLK inhibits ERASE and PROGRAM operations. Do not use VPPL and VPPH outside their valid ranges. 75 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2013 Micron Technology, Inc. All rights reserved. 512Mb, 1Gb, 2Gb: P33-65nm AC Test Conditions and Capacitance AC Test Conditions and Capacitance Figure 24: AC Input/Output Reference Timing VCCQ Input VCCQ/2 Test points VCCQ/2 output 0V Note: 1. AC test inputs are driven at VCCQ for logic 1 and at 0V for logic 0. Input/output timing begins/ends at VCCQ/2. Input rise and fall times (10% to 90%)
PC28F00AP33EF0
物料型号: - 该文档描述了Micron公司的Parallel NOR Flash Embedded Memory (P33-65nm)系列的多个物料型号,包括512Mb、1Gb和2Gb容量的芯片。具体型号包括JS28F512P33BFD、JS28F512P33TFA、JS28F512P33EFA等。

器件简介: - 这些是高性能的闪存设备,具有同步突发读取模式、快速异步访问时间、低功耗、灵活的安全选项和三种行业标准封装选择。产品采用Micron 65nm工艺技术制造。

引脚分配: - 引脚分配信息详细描述在文档的Pinouts and Ballouts部分,包括56-lead TSOP和64-ball Easy BGA封装的引脚布局和功能。

参数特性: - 参数特性包括高性能、易用的BGA封装特性、TSOP封装特性、架构特点、电压和功率参数、安全特性、软件特性、密度和封装信息、质量和可靠性等。

功能详解: - 功能详解部分介绍了虚拟芯片使能描述、存储器映射、引脚和球封装、信号描述、总线操作、读取操作、设备命令代码、编程操作、擦除操作、安全操作等。

应用信息: - 应用信息涉及了器件的一般描述、虚拟芯片使能描述、存储器映射、引脚和球封装尺寸、信号描述、总线操作、读取、编程、擦除、安全特性等。

封装信息: - 封装信息包括56-lead TSOP和64-ball Easy BGA的尺寸和特性,具体数值和尺寸图在文档的Package Dimensions部分给出。
PC28F00AP33EF0 价格&库存

很抱歉,暂时无法提供与“PC28F00AP33EF0”相匹配的价格&库存,您可以联系我们找货

免费人工找货