53111-1PA

53111 POWER MOSFET OPTOCOUPLER, 90 V/1 Ω, Hermetically Sealed, DSCC Approved 5962-9314001 and 5962-9314002 Mii MICROCIRCUITS PRODUCTS DIVISION Features: Applications: • • • • • • • • • • • • Hermetically Sealed 8-Pin Dual-In-Line package Small Size and Weight Options: 5mA or 10mA input forward current Performance Guaranteed over –55°C to +125°C Ambient Temperature Range AC/DC Signal & Power Switching Maximum Average Current AC/DC: 0.8 A DC only: 1.6 A 1500 VDC Withstand Test Voltage High Transient Immunity 5 A Output Surge Current Shock and Vibration Resistant MIL-PRF-38534 Compliant Equivalent to HSSR7111/7112 • • • • • • Satellite/Space Systems Military/High Reliability Systems Standard 28 VDC and 48 VDC Load Driver Standard 24 VAC Load Driver AC/DC Electromechanical and Solid State Relay Replacement I/O Modules DESCRIPTION The 53111 is a single channel, hermetically sealed, power MOSFET optocoupler. Low on-resistance of the MOSFET output, combined with 1500 VDC isolation between input and output, makes this optocoupler ideal for solid state relay applications. Operation is specified over the full military temperature range. The part is supplied in an eight-pin, dual-in-line ceramic package, available as COTS, as fully compliant MIL-PRF-38534 Class H device, or with custom screening. Lead options support both through-hole and surface-mount assembly. The part is normally shipped with gold plated leads, but lead finishes per MIL-PRF-38534 are available. Functionally, the device operates as a single-pole, normally open (1 Form A) solid state relay. The device is actuated by an input current, which can be supplied from standard logic types such as open-collector TTL. The input current biases a light emitting diode that is optically coupled to an integrated photovoltaic diode array. The photovoltaic array powers control circuitry that operates the output MOSFETs. Optimum switching of either AC or DC loads is provided by a configurable output. For AC loads, connection A in Figure 1 must be used. Connection A will also switch DC loads but connection B, in Figure 1, provides DC-only operation with the advantages of substantial reduction in on-resistance and twice the output current capability as that obtained with connection A. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 1 of 11 53111 Power MOSFET Optocoupler ___________________________________________________________________________________________ ABSOLUTE MAXIMUM RATINGS Storage Temperature Range ..................................................................................................................-65°C to +150°C Operating Ambient Temperature - TA .....................................................................................................-55°C to +125°C Junction Temperature - TJ ........................................................................................................................................150°C Operating Case Temperature - TC .....................................................................................................................+145°C (1) Lead Solder Temperature (1.6mm below seating plane).......................................................................... 260°C for 10s Average Input Current - IF ........................................................................................................................................20 mA Peak Repetitive Input Current - IFpk …(Pulse Width < 100ms; duty cycle < 50%) ...............................................40 mA Peak Surge Input Current - IFPK surge…(Pulse Width < 0.2ms; duty cycle < 0.1%)........................................100 mA Reverse Input Voltage - VR .................................................................................................................................... 5 V Average Output Current Connection A – IO............................................................................................................................................ 0.8 A Connection B - IO ............................................................................................................................................ 1.6 A Single Shot Output Current - Figure 4 Connection A - IOpk surge…(Pulse width < 10ms) ............................................................................................. 5 A Connection B - IOpk surge…(Pulse width < 10ms) ........................................................................................... 10 A Output Voltage Connection A - VO ............................................................................................................................ -90 V to +90 V Connection B - VO ............................................................................................................................... 0 V to +90 V Average Output Power Dissipation - Figure 5 ............................................................................................ 800 mW (2) RECOMMENDED OPERATING CONDITIONS: PARAMETER Input Current (on) Input Voltage (off) Operating Temperature SYMBOL IF (ON) VF (OFF) TA DEVICE TYPE -01 -02 All All MIN 10 5 0 -55 MAX 20 20 0.6 +125 UNITS mA mA VDC °C Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 2 of 11 53111 ELECTRICAL SPECIFICATIONS TA = -55°C to +125°C, unless otherwise specified. Parameter Output Withstand Voltage Sym. VO(OFF) Min. 90 Typ.* 110 Max. Units V Power MOSFET Optocoupler Test Conditions VF = 0.6 V IO = 10 µA IF = 10 mA (for –01) IF = 5 mA (for –02) IO = 800 mA (pulse duration ≤ 30 ms) IF = 10 mA (for –01) IF = 5 mA (for –02) IO = 1.6 A (pulse duration ≤ 30 ms) VF = 0.6 V VO = 90 V IF = 10 mA (for –01) IF = 5 mA (for –02) IR = 100 µA RH ≤ 45%, t = 5 s VI-O = 1500 VDC TA = 25°C IF = 10 mA (for –01) IF = 5 mA (for –02) VDD = 28 VDC IO = 800 mA IF = 10 mA (for –01) IF = 5 mA (for –02) VDD = 28 VDC IO = 800 mA VPEAK = 50 V CM = 1000 pF CL = 15 pF R M ≥ 1 MΩ VDD = 5 V VI-O (PEAK) = 50 V R L = 20 k Ω CL = 15 pF Notes Output On-Resistance (Connection A) R(ON) Output On-Resistance (Connection B) Output Leakage Current Input Forward Voltage Input Reverse Breakdown Voltage Input-Output Insulation IO (OFF) VF VR II-O 1.0 5.0 0.40 1.0 Ω 3, Figure 1 0.12 0.25 Ω 10-4 1.24 10 1.7 µA V V 1.0 µA 4, 5 Turn-On Time tON 1.25 6.0 ms Figure 6 Turn-Off time tOFF 0.02 0.25 ms Figure 6 Output Transient Rejection dVO/dt 1000 V/µs Figure 7 Input-Output Transient Rejection dVI-O/dt 500 V/µs Figure 8 * All typical values are at TA = 25ºC, IF (ON) = 10 mA (for -01) or 5 mA (for –02), VF (OFF) = 0.6V unless otherwise specified. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 3 of 11 53111 Power MOSFET Optocoupler TYPICAL CHARACTERISTICS All typical values are at TA = 25°C, IF (ON) = 10mA, VF (OFF) = 0.6V unless otherwise specified. Parameter Symbol Test Conditions VO = 28 V f = 1 MHz IF = 10 mA IO = 0 mA IF = 10 mA VF = 0 V f = 1 MHz VI-O = 0 V f = 1 MHz VI-O = 500 V t = 60 s Typ. Units Notes Output Off-Capacitance Output Offset Voltage Input Diode Temperature Coefficient Input Capacitance Input-Output Capacitance Input-Output Resistance CO (OFF) VOS ∆VF /∆TA CIN CI-O RI-O 145 2 -1.4 20 1.5 1013 pF µV mV/°C pF pF Ω 7 4 4 6 Notes: 1. Maximum junction to case thermal resistance for the device is 15ºC/W, where case temperature, TC, is measured at the center of the package bottom. 2. For rating, see Figure 5. The output power PD rating curve is obtained when the part is handling the maximum average output current IO as shown in Figure 3. 3. During the pulsed RON measurement (IO duration < 30 ms), ambient (TA) and case temperature (TC) are equal. 4. Pins 2 through 3 shorted together and pins 5 through 8 shorted together. 5. This is a momentary withstand test, not an operating condition. 6. VOS is a function of IF and is defined between pins 5 and 8, with pin 5 as the reference. VOS must be measured in a stable ambient (free of temperature gradients). 7. Zero-bias capacitance measured between the LED anode and cathode. CAUTION: Care should be taken not to exceed the maximum output power dissipation, maximum case temperature, and maximum junction temperature when repetitively switching loads. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 4 of 11 53111 Power MOSFET Optocoupler Case outlines Terminal number P, X, Y, AND Z Terminal symbol Connection A (AC or DC load) Conneciton B (DC load only) NC V F+ V FNC V O+ NC N OV O+ 1 2 3 4 5 6 7 8 NC = No connection NC V F+ V FNC VONC NC VO+ CONNECTION A AC/DC CONNECTION IO IF + VF 1 8 CONNECTION B DC CONNECTION IO IF + VF 1 8 + + VO - 2 7 2 7 VO 3 6 3 6 4 5 4 5 Figure 1 - Terminal Connections INPUT OFF ON OUTPUT OFF ON Figure 2 - Truth Table Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 5 of 11 53111 Power MOSFET Optocoupler I OPK- SURGE - OUTPUT CURRENT - A 1.0 0.8 0.6 0.4 0.2 0 -55 CONNECTION - A IF ≥10 mA __ θCA= 40°C/W - - θCA= 80°C/W -25 5 35 65 95 125 155 12 10 IF ≥10 mA CONNECTION - B I O - OUTPUT CURRENT- A 8 6 CONNECTION - A 4 2 0 10 100 PULSE DURATION - ms 1000 TA - AMBIENT TEMPERATURE - °C Figure 3. Maximum Average Output Current Rating vs. Ambient Temperature. Figure 4. Single Shot (nonrepetitive) Output Current vs. Pulse Duration. 1.0 0.8 0.6 0.4 0.2 0 -55 CONNECTION - A IF ≥10 mA __ θCA= 40°C/W - - θCA= 80°C/W -25 5 35 65 95 125 155 PD - OUTPUT POWER DISSIPATION - W TA - AMBIENT TEMPERATURE - °C Figure 5. Output Power Rating vs. Ambient Temperature. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 6 of 11 53111 Power MOSFET Optocoupler PULSE GEN (SEE NOTE 1) V DD RL 1 8 IF + VF IF MONITOR RM 200 2 7 VO MONITOR NODE C L = 25 pF (SEE NOTE 2) 3 6 4 5 GND 50% GND 50% IF PULSE = 15 ms WIDTH VO 10% 90% t ON t OFF NOTES: 1. PULSE GENERATOR HAS THE FOLLOWING CHARACTERISTICS: OUTPUT IMPEDANCE = 50 AND t r = t f = 5.0 ns. 2. LOAD CAPACITANCE (C L) INCLUDES PROBE AND JIG CAPACITANCE. Figure 6. Switching Test Circuit and Waveform. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 7 of 11 53111 Power MOSFET Optocoupler V 1 IF 8 CM RM M MONITOR NODE INPUT OPEN + VF 2 7 - 3 6 4 5 VO(PEAK) + PULSE GENERATOR 90% VO(PEAK) 90% 10% 10% tr tf VM (MAX) < 5V d VO dt = (0.8) V O (PEAK) tr OR (0.8) VO (PEAK) tf OVERSHOOT ON V O (PEAK) IS TO BE < 10% NOTES: 1. C M INCLUDES PROBE AND FIXTURE CAPACITANCE. 2. R M INCLUDES PROBE AND FIXTURE RESISTANCE. Figure 7. Output Transient Rejection Test Circuit and Waveform. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 8 of 11 53111 Power MOSFET Optocoupler V DD RL 1 IF 8 VO VF + - 2 7 CL 3 6 S1 B VIN A 4 V I-0 (PEAK) 5 + - PULSE GENERATOR 90% V I-0 (PEAK) 90% 10% 10% tr tf VO (OFF) S 1 AT A (VF = 0 V) V O (ON) S 1 AT B (NOTE 2) dV I-0 dt = (0.8) V I-0 (PEAK) tr VO (OFF) (MIN) > 3.25 V VO (ON) (MAX) < 0.8 V OR (0.8) V I-0 (PEAK) tf OVERSHOOT ON V I-0 (PEAK) IS TO BE < 10% NOTES: 1. LOAD CAPACITANCE (C L )INCLUDES PROBE AND FIXTURE CAPACITANCE. 2. FOR DEVICE TYPE 01, IF =10mA, FOR DEVICE TYPE 02, I F =5mA. Figure 8. Input-Output Transient Rejection Test Circuit and Waveform. Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 9 of 11 53111 Case Outline P Power MOSFET Optocoupler 31757 USA 53111 ESD SYMBOL .320 (8.13) MAX. .310 (7.87) .290 (7.37) Q XXXXX PIN 1 .050 (1.27) .035 (0.89) .390 (9.91) .370 (9.41) .170 (4.32) MAX. .150 (3.81) MIN. .050 (1.27) .030 (0.76) .020 (0.51) MAX. .110 (2.79) .090 (2.29) Case Outline X .050 (1.27) .035 (0.89) .390 (9.91) .370 (9.41) .170 (4.32) MAX. .110 (2.79) .090 (2.29) .020 (.051) MAX. .013 (0.33) .007 (0.18) .047 (1.19) TYP .390 (9.91) .380 (7.87) .320 (8.13) MAX .180 (4.57) MAX .065 (1.65) .055 (1.40) SEATING PLANE .020 (0.51) MIN 5° 0° Case Outline Y .050 (1.27) .035 (0.89) .390 (9.91) .370 (9.41) .170 (4.32) MAX. .320 (8.13) MAX .020 (0.51) MIN .110 (2.79) .090 (2.29) .020 (0.51) MAX. SEATING PLANE .055 (1.40) .045 (1.14) .013 (0.33) .007 (0.18) .310 (7.87) .290 (7.37) Case Outline Z .050 (1.27) .035 (0.89) .390 (9.91) .370 (9.41) .140 (3.56) MAX. .110 (2.79) .090 (2.29) SEATING PLANE .013 (0.33) .007 (0.18) .310 (7.87) .290 (7.37) .320 (8.13) MAX .020 (0.51) MIN .045 (1.14) .035 (0.89) NOTES: 1. PIN 1 IS INDICATED BY THE ESD TRIANGLE MARKED ON THE LID OF THE PACKAGE. 2. DIMENSIONS ARE IN INCHES, (mm). 3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY. 4. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS ±.005 (0.13mm). Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 10 of 11 53111 ORDERING GUIDE Power MOSFET Optocoupler The followings are the cross-reference of Micropac part numbers versus Standard Military PIN. Please contact Micropac for other desired options. Micropac Part Number 53111-1PA 53111-1PC 53111-1XA 53111-1XC 53111-1YA 53111-1YC 53111-1ZA 53111-1ZC 53111-2PA 53111-2PC 53111-2XA 53111-2XC 53111-2YA 53111-2YC 53111-2ZA 53111-2ZC Standard Military Drawing PIN 5962-9314001HPA 5962-9314001HPC 5962-9314001HXA 5962-9314001HXC 5962-9314001HYA 5962-9314001HYC 5962-9314001HZA 5962-9314001HZC 5962-9314002HPA 5962-9314002HPC 5962-9314002HXA 5962-9314002HXC 5962-9314002HYA 5962-9314002HYC 5962-9314002HZA 5962-9314002HZC Case Outline P P X X Y Y Z Z P P X X Y Y Z Z Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: hybridsales@micropac.com 5/22/02 www.micropac.com Pg. 11 of 11