66193

66193 SINGLE CHANNEL OPTOCOUPLERS REPLACEMENT FOR 3C91C Mii OPTOELECTRONIC PRODUCTS DIVISION Features: • • • • • High Reliability Base lead eliminated for improved noise immunity Rugged package Stability over wide temperature +500V electrical isolation Applications: • • • • • Eliminate ground loops Level shifting Line receiver Switching power supplies Motor control DESCRIPTION The 66193 contains a proton tolerant LED optically coupled to a silicon planar phototransistor. The optocoupler is built on a TO-46 header. The anode of the LED is electrically connected to the case. This optocoupler is capable of transmitting signals between two galvanic sources. The potential difference between transmitter and receiver should not go over the maximum isolation voltage. The internal base connection has been eliminated for improved noise immunity. ABSOLUTE MAXIMUM RATINGS Input to Output Voltage...........................................................................................................................................................500V Emitter-Collector Voltage............................................................................................................................................................5V Collector-Emitter Voltage (Value applies to emitter-base open-circuited & the input-diode equal to zero) ............................60V Reverse Input Voltage ...............................................................................................................................................................7V Input Diode Continuous Forward Current at (or below) 65°C Free-Air Temperature (see note 1) .....................................50mA Peak Forward Input Current (Value applies for tw < 1µs, PRR < 300 pps) .........................................................................50mA Continuous Collector Current .....................................................................................................................................................1A Continuous Transistor Power Dissipation at (or below) 25°C Free-Air Temperature (see Note 2) .................................300mW Storage Temperature.......................................................................................................................................... -65°C to +150°C Operating Free-Air Temperature Range ............................................................................................................. -55°C to +100°C Lead Solder Temperature (10 seconds max.) .................................................................................................................... 240°C Notes: 1. Derate linearly to +65°C free-air temperature at the rate of 1.15 mA/°C. 2. Derate linearly to 100°C free-air temperature at the rate of 3 mW/°C. Package Dimensions Schematic Diagram 4 LEADS 0.019Ø (0.48) 0.016Ø (0.41) 0.230Ø (5.84) 0.209Ø (5.31) EMITTER COLLECTOR 2 3 Ø0.100[2.54] ANODE 0.195Ø (4.95) 0.178Ø (4.52) 4 1 0.048 [1.22] 0.028 [0.71] 45° CATHODE 0.030 (0.76) MAX 0.210 [5.34] 0.170 [4.32] 0.50 [12.70] MIN 0.046 [1.17] 0.036 [0.91] DIMENSIONS ARE IN INCHES (MILLIMETERS) NOTE: ANODE ELECTRICALLY CONNECTED TO CASE MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918 www.micropac.com E-MAIL: optosales@micropac.com 3 - 44 66193 ELECTRICAL CHARACTERISTICS TA = 25°C unless otherwise specified. SINGLE CHANNEL OPTOCOUPLER (Replacement for 3C91C) PARAMETER Input Diode Static Reverse Current Input Diode Static Forward Voltage Input Diode Static Forward Voltage Reverse Breakdown Voltage Input Diode Capacitance SYMBOL IR VF VF BVR CIN MIN TYP MAX 1 2.0 2.2 UNITS µA V V V PF TEST CONDITIONS VR = 3V IF = 10mA IF = 20mA IR = 100µA V = 0V, f = 1MHz 7 12 25 OUTPUT TRANSISTOR TA = 25°C unless otherwise specified. PARAMETER Collector-Emitter Breakdown Voltage Emitter-Collector Breakdown Voltage Collector-Emitter Dark Current SYMBOL V(BR)CEO V(BR)ECO ICEO1 ICEO2 MIN 50 7 TYP MAX UNITS V V TEST CONDITIONS IC = 1mA, IB = 0, IF = 0 IC = 10µA VCE = 50V, VCE = 5V, IF = 0mA IF = 0mA 100 10 nA nA COUPLED CHARACTERISTICS TA = 25°C unless otherwise specified. PARAMETER On State Collector Current On State Collector Current On State Collector Current Collector-Emitter Saturation Voltage Isolation Resistance Input to Output Capacitance Delay Time Storage Time Rise Time Fall Time -55°C SYMBOL IC(ON) IC(ON) IC(ON) VCE(SAT) RISO CIO td ts tr tf MIN 4 3 2 TYP MAX UNITS mA mA mA TEST CONDITIONS VCE = 5V, IF = 10mA VCE = 0.4V, IF = 10mA VCE = 5V, IF = 10mA IF = 50mA, IC = 10mA VIN-OUT = 500V f = 1MHz VCE = 5V, IF = 2mA, RL = 100Ω VCE = 5V, IF = 2mA, RL = 100Ω VCE = 5V, IF = 2mA, RL = 100Ω VCE = 5V, IF = 2mA, RL = 100Ω 0.4 10 9 V Ω 2 2 0.2 3 4 2.5 4 0.5 5 5 pF µs µs µs µs RECOMMENDED OPERATING CONDITIONS: PARAMETER Input Current, Low Level Input Current, High Level Supply Voltage Operating Temperature SYMBOL IFL MIN 0 2 5 -55 MAX 1 20 50 100 UNITS µA mA V °C IFH VCE TA SELECTION GUIDE PART NUMBER 66193-001 66193-011 66193-101 PART DESCRIPTION Single Channel optocoupler, commercial (0° to 70°C) Single Channel optocoupler –55 to +100°C Single Channel optocoupler –55 to+100°C with 100% device screening MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918 www.micropac.com E-MAIL: optosales@micropac.com 3 - 45