2N6796

TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 N-CHANNEL MOSFET Qualified per MIL-PRF-19500/557 DEVICES LEVELS 2N6796 2N6796U JAN JANTX JANTXV Symbol VDS VGS Value 100 ± 20 8.0 5.0 25 (1) 1.8 (2) ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted) Parameters / Test Conditions Drain – Source Voltage Gate – Source Voltage Continuous Drain Current TC = +25°C Continuous Drain Current TC = +100°C Max. Power Dissipation Drain to Source On State Resistance Operating & Storage Temperature Note: (1) Derated Linearly by 0.2 W/°C for TC > +25°C (2) VGS = 10Vdc, ID = 5.0A ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted) Parameters / Test Conditions OFF CHARACTERTICS Drain-Source Breakdown Voltage VGS = 0V, ID = 1mAdc Gate-Source Voltage (Threshold) VDS ≥ VGS, ID = 0.25mA VDS ≥ VGS, ID = 0.25mA, Tj = +125°C VDS ≥ VGS, ID = 0.25mA, Tj = -55°C Gate Current VGS = ±20V, VDS = 0V VGS = ±20V, VDS = 0V, Tj = +125°C Drain Current VGS = 0V, VDS = 80V VGS = 0V, VDS = 80V, Tj = +125°C Static Drain-Source On-State Resistance VGS = 10V, ID = 5.0A pulsed VGS = 10V, ID = 8.0A pulsed Tj = +125°C VGS = 10V, ID = 5.0A pulsed Diode Forward Voltage VGS = 0V, ID = 8.0A pulsed Symbol V(BR)DSS VGS(th)1 VGS(th)2 VGS(th)3 IGSS1 IGSS2 IDSS1 IDSS2 rDS(on)1 rDS(on)2 rDS(on)3 VSD Min. 100 2.0 1.0 4.0 5.0 ±100 ±200 25 0.25 0.18 0.195 0.35 1.5 nAdc µAdc mAdc Ω Ω Ω Vdc Max. Unit Vdc Vdc Unit Vdc Vdc Adc Adc W Ω °C TO-205AF (formerly TO-39) ID1 ID2 Ptl Rds(on) Top, Tstg -55 to +150 U – 18 LCC T4-LDS-0047 Rev. 2 (101281) Page 1 of 4 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 DYNAMIC CHARACTERISTICS Parameters / Test Conditions Gate Charge: On-State Gate Charge Gate to Source Charge Gate to Drain Charge SWITCHING CHARACTERISTICS Parameters / Test Conditions Switching time tests: Turn-on delay time Rinse time Turn-off delay time Fall time Diode Reverse Recovery Time ID = 8.0A, VGS = 10Vdc, Gate drive impedance = 7.5Ω, VDD = 30Vdc di/dt ≤ 100A/µs, VDD ≤ 50V, IF = 8.0A Symbol td(on) tr td(off) tf trr Min. Max. 30 75 40 45 300 Unit Symbol Qg(on) Qgs Qgd Min. Max. 28.51 6.34 16.59 Unit VGS = 10V, ID = 8.0A VDS = 50V nC ns ns T4-LDS-0047 Rev. 2 (101281) Page 2 of 4 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Ltr CD CH HD h J k LD LL LS LU L1 L2 P Q r α Dimensions Inches Millimeters Min Max Min Max .305 .355 7.75 9.02 .160 .180 4.07 4.57 .335 .370 8.51 9.39 .009 .041 0.23 1.04 .028 .034 0.72 0.86 .029 .045 0.74 1.14 .016 .021 0.41 0.53 .500 .750 12.7 19.05 .200 TP 5.08 TP .016 .019 0.41 0.48 .050 1.27 .250 6.35 .070 1.78 .050 1.27 .010 0.25 45° TP 45° TP Notes 2 3 7, 8 7, 8 6 7, 8 7, 8 7, 8 5 4 9 6 NOTES: Dimensions are in inches. Millimeters are given for general information only. Beyond radius (r) maximum, j shall be held for a minimum length of .011 (0.028 mm). Dimension k measured from maximum HD. Outline in this zone is not controlled. Dimension CD shall not vary more than .010 (0.25 mm) in zone P. This zone is controlled for automatic handling. 6. Leads at gauge plane .054 +.001, -.000 (1.37 +0.03, -0.00 mm) below seating plane shall be within .007 (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. 6 LU applies between L1 and L2. LD applies between L2 and L minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 7 All three leads. 8 Radius (r) applies to both inside corners of tab. 9 Drain is electrically connected to the case. 10 In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. 1 2 3 4 5 FIGURE 1. Physical dimensions for TO-205AF. T4-LDS-0047 Rev. 2 (101281) Page 3 of 4 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS NOTES: 1 2 3 4 Dimensions are in inches. Millimeters are given for general information only. In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. Ceramic package only. Ltr BL BW CH LL1 LL2 LS LS1 LS2 LW Q1 Q2 Q3 TL TW Dimensions Inches Millimeters Min Max Min Max .345 .360 8.77 .280 .295 7.11 .095 .115 2.41 .040 .055 1.02 .055 .065 1.40 .050 BSC 1.27 BSC .025 BSC 0.635 BSC .008 BSC 0.203 BSC .020 .030 0.51 0.76 .105 REF 2.67 REF .120 REF 3.05 REF .045 .055 1.14 1.40 .070 .080 1.78 2.03 .120 .130 3.05 3.30 FIGURE 2. Physical dimensions for LCC. T4-LDS-0047 Rev. 2 (101281) Page 4 of 4