2N6901

TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 N-CHANNEL LOGIC LEVEL MOSFET Qualified per MIL-PRF-19500/570 DEVICES LEVELS 2N6901 JAN JANTX JANTXV ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted) Parameters / Test Conditions Drain – Source Voltage Gate – Source Voltage Continuous Drain Current TC = +25°C Continuous Drain Current TC = +100°C Max. Power Dissipation Drain to Source On State Resistance Operating & Storage Temperature Note: (1) Derated Linearly by 0.067 W/°C for TC > +25°C (2) VGS = 5Vdc, ID = 1.07A ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted) Parameters / Test Conditions OFF CHARACTERTICS Drain-Source Breakdown Voltage VGS = 0V, ID = -1mAdc Gate-Source Voltage (Threshold) VDS ≥ VGS, ID = 1.0mA VDS ≥ VGS, ID = 1.0mA, Tj = +125°C VDS ≥ VGS, ID = 1.0mA, Tj = -55°C Gate Current VGS = ±10V, VDS = 0V VGS = ±10V, VDS = 0V, Tj = +125°C Drain Current VGS = 0V, VDS = 80V VGS = 0V, VDS = 80V, Tj = +125°C Static Drain-Source On-State Resistance VGS = 5V, ID = 1.07A pulsed Tj = -125°C VGS = 5V, ID = 1.07A pulsed Diode Forward Voltage VGS = 0V, ID = 1.69A pulsed T4-LDS-0188 Rev. 1 (101985) V(BR)DSS VGS(th)1 VGS(th)2 VGS(th)3 IGSS1 IGSS2 IDSS1 IDSS2 rDS(on)1 rDS(on)2 VSD 0.8 100 1.0 0.5 2.0 3.0 ±100 ±200 1.0 50.0 1.4 2.6 1.6 nAdc Vdc Vdc Symbol Min. Max. Unit Symbol VDS VGS ID1 ID2 Ptl Rds(on) Top, Tstg Value 100 ± 10 1.69 1.07 8.33 (1) 1.4 (2) Unit Vdc Vdc Adc Adc W Ω °C 2N6901 TO-205AF (formerly TO-39) SEE FIGURE 1 -55 to +150 µAdc uAdc Ω Ω Vdc Page 1 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 DYNAMIC CHARACTERISTICS Parameters / Test Conditions Gate Charge: On-State Gate Charge Gate to Source Charge Gate to Drain Charge SWITCHING CHARACTERISTICS Parameters / Test Conditions Switching time tests: Turn-on delay time Rinse time Turn-off delay time Fall time Diode Reverse Recovery Time Symbol ID = 1.69A, VGS = 5Vdc, Gate drive impedance = 25Ω, VDD = 50Vdc di/dt ≤ 100A/µs, VDD ≤ 30V, IF = 1.0A td(on) tr td(off) tf trr Min. Max. 25 80 45 80 250 Unit Symbol VGS = 5V, ID = 1.69A VDS = 50V Qg(on) Qgs Qgd Min. Max. 5.0 1.0 2.9 Unit nC ns ns T4-LDS-0188 Rev. 1 (101985) Page 2 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Symbol CD CH HD LC LD LL LU L1 L2 P Q TL TW r α Dimensions Inches Millimeters Min Max Min Max .305 .335 7.75 8.51 .160 .180 4.07 4.57 .335 .370 8.51 9.40 .200 TP 5.08 TP .016 .021 0.41 0.53 .500 .750 12.70 19.05 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .100 2.54 .050 1.27 .029 .045 0.74 1.14 .028 .034 0.71 0.86 .010 0.25 45° TP 45° TP 8,9 8,9 8,9 8,9 8,9 6 5 4 3 10 6 NOTE: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Dimensions are in inches. Millimeters are given for general information only. Beyond radius(r) maximum, TW shall be held for a minimum length of .011 (0.28 mm). Dimension TL measured from maximum HD. Outline in this zone is not controlled. Dimension CD shall not vary more than .010 (0.25 mm) in zone P. This zone is controlled for automatic handling. Leads at gauge plane .054 +.001, -.000 (1.37 +0.03, -0.00 mm) below seating plane shall be within .007 (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. LU applies between L1 and L2. LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. All three leads. Radius(r) applies to both inside corners of tab. Drain is electrically connected to the case. Pin out: 1- source, 2 - gate, 3 - drain (case). In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. FIGURE 1. Physical dimensions for TO-205 AF T4-LDS-0188 Rev. 1 (101985) Page 3 of 3