2N6989_1

TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland. Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 MULTIPLE (QUAD) NPN SILICON DUAL IN-LINE AND FLATPACK SWITCHING TRANSISTOR Qualified per MIL-PRF-19500/559 DEVICES LEVELS 2N6989 2N6990 2N6989U JAN JANTX JANTXV JANS ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted) Parameters / Test Conditions Collector-Emitter Voltage (3) Collector-Base Voltage (3) Emitter-Base Voltage (3) Collector Current (3) Total Power Dissipation @ TA = +25°C 2N6989 2N6989U (2) 2N6990 (2) (2) Symbol VCEO VCBO VEBO IC PD Top, Tstg Value 50 75 6.0 800 1.5 1.0 1.0 -65 to +200 Unit Vdc Vdc Vdc mAdc W °C TO-116 – 2N6989 Operating & Storage Junction Temperature Range Note: 1. 2. 3. 4. Maximum voltage between transistors shall be ≥ 500Vdc. For derating, see figures 6, 7, 8 and 9. Ratings apply to total package. For thermal impedance curves, see figures 10, 11, 12 and 13. Ratings apply to each transistor in the array. 20 PIN LEADLESS 2N6989U Max. Unit Vdc 10 10 10 10 10 ηAdc μAdc μAdc μAdc ηAdc 14 PIN FLAT PACK 2N6990 ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted) Parameters / Test Conditions OFF CHARACTERTICS Symbol V(BR)CEO Min. 50 Collector-Emitter Breakdown Voltage IC = 10mAdc Collector-Base Cutoff Current VCB = 60Vdc VCB = 75Vdc VCB = 60Vdc, TA = +150°C Emitter-Base Cutoff Current VEB = 4.0Vdc VEB = 6.0Vdc ICBO IEBO T4-LDS-0177 Rev. 1 (101229) Page 1 of 7 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland. Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted) Parameters / Test Conditions ON CHARACTERISTICS Forward-Current Transfer Ratio IC = 0.1mAdc, VCE = 10Vdc IC = 1.0mAdc, VCE = 10Vdc IC = 10mAdc, VCE = 10Vdc IC = 150mAdc, VCE = 10Vdc IC = 500mAdc, VCE = 10Vdc IC = 10mAdc, VCE = 10Vdc, TA = -55°C Collector-Emitter Saturation Voltage IC = 150mAdc, IB = 15mAdc IC = 500mAdc, IB = 50mAdc Base-Emitter Saturation Voltage IC = 150mAdc, IB = 15mAdc IC = 500mAdc, IB = 50mAdc DYNAMIC CHARACTERISTICS Parameters / Test Conditions Magnitude of Small–Signal Short-Circuit Forward Current Transfer Ratio IC = 20mAdc, VCE = 10Vdc, f = 100MHz Forward current Transfer Ratio IC = 1.0mAdc, VCE = 10Vdc, f = 1.0kHz Output Capacitance VCB = 10Vdc, IE = 0, 100kHz ≤ f ≤ 1.0MHz Input Capacitance VEB = 0.5Vdc, IE = 0, 100kHz ≤ f ≤ 1.0MHz SWITCHING CHARACTERISTICS Parameters / Test Conditions Turn-On Time SEE FIGURE 14 / MIL-PRF-19500/559 Turn-Off Time SEE FIGURE 15 / MIL-PRF-19500/559 (4) Pulse Test: Pulse Width = 300μs, Duty Cycle ≤ 2.0%. (4) Symbol Min. Max. Unit hFE 50 75 100 100 30 35 325 300 VCE(sat) 0.3 1.0 0.6 1.2 2.0 Vdc VBE(sat) Vdc Symbol |hfe| hfe Cobo Cibo Min. 2.5 50 Max. 8.0 Unit 8.0 25 pF pF Symbol ton toff Min. Max. 35 300 Unit ηs ηs T4-LDS-0177 Rev. 1 (101229) Page 2 of 7 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland. Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS T4-LDS-0177 Rev. 1 (101229) Page 3 of 7 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland. Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Symbol BH LW LW1 LT BL BW BW1 Dimensions Inches Millimeters Min Max Min Max .200 5.08 .014 .023 0.36 0.58 .030 .070 0.76 1.78 .008 .015 0.20 0.38 .785 19.94 .220 .310 5.59 7.87 .290 .320 7.37 8.13 Dimensions Notes Symbol LS LL LL1 LO LO1 LO2 α Inches Min Max .100 BSC .125 .200 .150 .005 .098 .015 .060 0° 15° Millimeters Min Max 2.54 BSC 3.18 5.08 3.81 0.13 2.49 0.38 1.52 0° 15° Notes 7, 11 10 4, 10 10 6 6 9 8 8 5 NOTES: 1 2 3 4 5 6 7 8 9 10 11 12 13 Dimension are in inches. Millimeters are given for general information only. Index area: A notch or pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. The minimum limit for dimension LW1 may be .023 inch (0.58 mm) for leads number 1, 7, 8 and 14 only. Dimension LO2 shall be measured from the seating plane to the base plane. This dimension allows for off-center lid, meniscus, and glass overrun. The basic pin spacing is .100 inch (2.54 mm) between centerlines. Each pin centerline shall be located within ±.010 inch (0.25 mm) of its exact longitudinal position relative to pins 1 and 14. Applies to all four corners (leads number 1, 7, 8 and 14). Lead center when α is 0 degrees. BW1 shall be measured at the centerline of the leads. All leads. Twelve spaces. No organic or polymeric materials shall be molded to the bottom of the package to cover the leads. In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. FIGURE 1. Physical Dimension and Configuration for type 2N6989 T4-LDS-0177 Rev. 1 (101229) Page 4 of 7 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland. Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Symbol CH LW TL BL BW LU BW2 Dimensions Inches Millimeters Min Max Min Max .030 .115 0.76 2.92 .010 .019 0.25 0.48 .008 .015 0.20 0.38 .280 7.11 .240 .260 6.10 6.60 .290 7.37 .125 3.18 Dimensions Notes Symbol BW3 LS LT LL LD2 LO LO3 α Inches Min Max .030 .050 BSC .003 .006 .250 .370 .005 .040 .005 .004 30° 90° Millimeters Min Max 0.76 1.27 BSC 0.076 0.152 6.35 9.40 0.13 1.02 0.13 30° 90° Notes 7 12 5 5 6, 8 7 4 9, 10 13 14 T4-LDS-0177 Rev. 1 (101229) Page 5 of 7 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland. Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 NOTES: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Dimension are in inches. Millimeters are given for general information only. Index area: A notch or pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. Alternatively, a tab (dine TL) may be used to identify pin one. Dimension LD2 shall be measured at the point of exit of the lead from the body. This dimension allows for off-center lid, meniscus, and glass overrun. The basic pin spacing is .050 inch (1.27 mm) between centerlines. Each pin centerline shall be located within ±.005 inch (0.13 mm) of its exact longitudinal position relative to pins 1 and 14. All leads: Increase maximum limit by .003 inch (0.08 mm) measured at the center of the flat when the lead finish is solder. Twelve spaces. Applies to all four corners (leads number 2, 6, 9 and 13). Dimension LO may be .000 inch (0.00 mm if leads number 2, 6, 9, and 13) bend toward the cavity of the package within one lead width from the point of entry of the lead into the body or if the leads are brazed to the metalized ceramic body. No organic or polymeric materials shall be molded to the bottom of the package to cover the leads. Optional, see note 1. If a pin one identification mark is used in addition to this tab, the minimum limit of dimension TL does not apply. Applies to leads number 1, 7, 8, and 14. Lead configuration is optional within dimension BW except dimensions LW and LT apply. In accordance with ASME Y14.5M, diameters are eqivalent to φx symbology. Pins 1, 7, 8, and 14 are collectors. Pin 2, 6, 9, and 13 are bases. Pin 3, 5, 10, and 12 are emitters. Pins 4 and 11 are no contacts. FIGURE 2. Physical dimensions for type 2N6990 FIGURE 3. Schematic and terminal connections for types 2N6989 & 2N6990 T4-LDS-0177 Rev. 1 (101229) Page 6 of 7 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland. Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS NOTES: 1 2 3 4 Dimensions are in inches. Millimeters are given for general information only. Unless otherwise specified, tolerance is ±.005 inch (0.13 mm). In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. Symbol A A1 D D1 D2 D3 E L1 L2 Dimensions Inches Min Max .073 .085 .063 .075 .345 .355 .195 .205 .050 TYP .070 .080 .025 REF .050 REF for pins 2 through 20 .080 .090 Millimeters Min Max 1.85 2.16 1.60 1.91 8.76 9.02 4.95 5.21 1.27 TYP 1.78 2.03 0.64 REF 1.27 REF for pins 2 through 20 2.03 2.29 FIGURE 4. Physical demension for type 2N6989U T4-LDS-0177 Rev. 1 (101229) Page 7 of 7