APT20GS60BRDQ1G

APT20GS60BRDQ1(G) APT20GS60SRDQ1(G) 600V, 20A, VCE(ON) = 2.8V Typical Thunderbolt® High Speed NPT IGBT with Anti-Parallel 'DQ' Diode The Thunderbolt HS™ series is based on thin wafer non-punch through (NPT) technology similar to the Thunderbolt® series, but trades higher VCE(ON) for significantly lower turn-on energy Eoff. The low switching losses enable operation at switching frequencies over 100kHz, approaching power MOSFET performance but lower cost. An extremely tight parameter distribution combined with a positive VCE(ON) temperature coefficient make it easy to parallel Thunderbolts HS™ IGBT's. Controlled slew rates result in very good noise and oscillation immunity and low EMI. The short circuit duration rating of 10µs make these IGBT's suitable for motor drive and inverter applications. Reliability is further enhanced by avalanche energy ruggedness. Combi versions are packaged with a high speed, soft recovery DQ series diode. TO -2 47 D3PAK Features • Fast Switching with low EMI • Very Low EOFF for Maximum Efficiency • Short circuit rated • Low Gate Charge • Tight parameter distribution • Easy paralleling • RoHS Compliant Typical Applications APT20GS60BRDQ1(G) APT20GS60SRDQ1(G) • ZVS Phase Shifted and other Full Bridge • Half Bridge • High Power PFC Boost • Welding • Induction heating • High Frequency SMPS Single die IGBT with separate DQ diode die Absolute Maximum Ratings Symbol I C1 I C1 I CM VGE SSOA EAS tSC IF I FRM Symbol PD RθJC RθCS TJ, TSTG TL WT Torque Parameter Continuous Collector Current TC = @ 25°C Continuous Collector Current TC = @ 100°C Pulsed Collector Current 1 Gate-Emitter Voltage Switching Safe Operating Area Single Pulse Avalanche Energy 2 Short Circut Withstand Time 3 Diode Continuous Forward Current Diode Max. Repetitive Forward Current Parameter Total Power Dissipation TC = @ 25°C Junction to Case Thermal Resistance Case to Sink Thermal Resistance, Flat Greased Surface Operating and Storage Junction Temperature Range Soldering Temperature for 10 Seconds (1.6mm from case) Package Weight Mounting Torque (TO-247), 6-32 M3 Screw IGBT Diode -55 0.11 0.22 5.9 Min TC = 25°C TC = 100°C Rating 37 20 80 ±30V 80 115 10 43 26 80 Typ Max 180 0.70 1.35 150 300 10 1.1 °C oz g in·lbf N·m 8-2007 052-6304 Rev A Unit A V mJ µs A Thermal and Mechanical Characteristics Unit W °C/W CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should be Followed. Microsemi Website - http://www.microsemi.com Static Characteristics Symbol VBR(CES) ∆VBR(CES)/∆TJ TJ = 25°C unless otherwise specified Test Conditions VGE = 0V, IC = 250µA Reference to 25°C, IC = 250µA APT20GS60B_SRDQ1(G) Min 600 3 Typ 0.60 2.8 3.25 2.2 1.75 4 6.7 Max 3.15 5 50 1000 ±100 mV/°C µA nA V Unit V V/°C Parameter Collector-Emitter Breakdown Voltage Breakdown Voltage Temperature Coeff VCE(ON) VEC VGE(th) Collector-Emitter On Voltage 4 Diode Forward Voltage 4 Gate-Emitter Threshold Voltage VGE = 15V IC = 20A IC = 20A TJ = 25°C TJ = 125°C TJ = 25°C TJ = 125°C ∆VGE(th)/∆TJ Threshold Voltage Temp Coeff ICES IGES Zero Gate Voltage Collector Current Gate-Emitter Leakage Current VGE = VCE, IC = 1mA VCE = 600V, VGE = 0V TJ = 25°C TJ = 125°C VGE = ±20V Dynamic Characteristics Symbol gfs Cies Coes Cres Co(cr) Co(er) Qg Qge Ggc td(on) tr td(off) tf Eon1 Eon2 Eoff td(on) tr td(off) tf Eon1 Eon2 Eoff trr 8-2007 Parameter Input Capacitance Output Capacitance TJ = 25°C unless otherwise specified Test Conditions VCE = 50V, IC = 20A Min - Typ 12 1085 100 65 95 90 Max - Unit S Forward Transconductance Reverse Transfer Capacitance Reverse Transfer Capacitance Charge Related 5 Reverse Transfer Capacitance Current Related 6 Total Gate Charge Gate-Emitter Charge Gate-Collector Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Turn-On Switching Energy Turn-On Switching Energy Turn-Off Switching Energy Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Turn-On Switching Energy Turn-On Switching Energy 8 9 8 9 10 VGE = 0V, VCE = 25V f = 1MHz pF VGE = 0V VCE = 0 to 400V VGE = 0 to 15V IC = 20A, VCE = 300V - 100 8 48 8 14 130 12 TBD 295 200 8 14 145 23 TBD 465 300 19 21 2 ns nC A µJ ns µJ ns nC Inductive Switching IGBT and Diode: TJ = 25°C, VCC = 400V, IC = 20A RG = 9.1Ω 7, VGG = 15V Inductive Switching IGBT and Diode: TJ = 125°C, VCC = 400V, IC = 20A RG = 9.1Ω 7, VGG = 15V - Turn-Off Switching Energy 10 Diode Reverse Recovery Time Diode Reverse Recovery Charge Peak Reverse Recovery Current IF = 20A VR = 400V diF/dt = 200A/µs Qrr Irrm 052-6304 Rev A TYPICAL PERFORMANCE CURVES 80 70 IC, COLLECTOR CURRENT (A) 60 50 40 30 20 10 0 0 1 2 3 4 5 6 7 VCE(ON), COLLECTER-TO-EMITTER VOLTAGE (V) FIGURE 1, Output Characteristics 250µs PULSE TEST