APT8028JVR

APT8028JVR 800V 28A 0.280Ω S G D S POWER MOS V ® Power MOS V® is a new generation of high voltage N-Channel enhancement mode power MOSFETs. This new technology minimizes the JFET effect, increases packing density and reduces the on-resistance. Power MOS V® also achieves faster switching speeds through optimized gate layout. SO ISOTOP ® 2 T- 27 "UL Recognized" • Faster Switching • Lower Leakage • 100% Avalanche Tested • Popular SOT-227 Package G D Unless stated otherwise, Microsemi discrete MOSFETs contain a single MOSFET die. This device is made with two parallel MOSFET die. It is intended for switch-mode operation. It is not suitable for linear mode operation. S Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 APT8028JVR UNIT Volts Amps 800 28 112 ±30 ±40 500 4 -55 to 150 300 16 30 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 1300 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS ID(on) RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) On State Drain Current 2 MIN TYP MAX UNIT Volts Amps 800 28 0.280 50 500 2 4 ±100 (VDS > ID(on) x R DS(on) Max, VGS = 10V) 2 Drain-Source On-State Resistance (VGS = 10V, 0.5 ID[Cont.]) Ohms µA nA Volts Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 0.8 VDSS, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 1mA) CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. Microsemi Website - http://www.microsemi.com 050-5607 Rev C 6-2006 DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 APT8028JVR Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 0.5 VDSS ID = ID[Cont.] @ 25°C VGS = 15V VDD = 0.5 VDSS ID = ID[Cont.] @ 25°C RG = 0.6Ω MIN TYP MAX UNIT 7700 730 350 380 38 165 13 10 51 8 9240 1020 425 570 55 245 26 20 75 16 ns nC pF Gate-Source Charge Gate-Drain ("Miller ") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS Symbol IS ISM VSD t rr Q rr Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage 1 2 MIN TYP MAX UNIT Amps Volts ns µC 28 112 1.3 950 21 (Body Diode) (VGS = 0V, IS = - ID[Cont.]) Reverse Recovery Time (IS = -ID[Cont.], dl S/dt = 100A/µs) Reverse Recovery Charge (IS = -ID[Cont.], dl S /dt = 100A/µs) THERMAL / PACKAGE CHARACTERISTICS Symbol RθJC RθJA VIsolation Torque Characteristic Junction to Case Junction to Ambient RMS Voltage (50-60 Hz Sinusoidal Waveform From Terminals to Mounting Base for 1 Min.) Maximum Torque for Device Mounting Screws and Electrical Terminations. MIN TYP MAX UNIT °C/W Volts 0.25 40 2500 13 lb•in 1 Repetitive Rating: Pulse width limited by maximum junction temperature. 2 Pulse Test: Pulse width < 380 µS, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 4 Starting T = +25°C, L = 10.16mH, R = 25Ω, Peak I = 16A j G L Microsemi reserves the right to change, without notice, the specifications and information contained herein. 0.3 Z JC, THERMAL IMPEDANCE (°C/W) θ D=0.5 0.1 0.2 0.05 0.1 0.05 0.02 0.01 SINGLE PULSE PDM 0.01 0.005 Note: t1 t2 Duty Factor D = t1/t2 Peak TJ = PDM x ZθJC + TC 050-5607 Rev C 6-2006 0.001 10-5 10-3 10-2 10-1 1.0 10 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 10-4 APT8028JVR 50 VGS=5.5V, 6V, 7V, 10V & 15V ID, DRAIN CURRENT (AMPERES) ID, DRAIN CURRENT (AMPERES) 50 VGS=15V VGS=10V VGS=5.5V, 6V & 7V 5V 40 5V 40 30 30 20 4.5V 20 4.5V 10 4V 0 80 160 240 320 400 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 2, TYPICAL OUTPUT CHARACTERISTICS 0 10 4V 0 3 6 9 12 15 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 3, TYPICAL OUTPUT CHARACTERISTICS 0 RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE 50 ID, DRAIN CURRENT (AMPERES) VDS> ID (ON) x RDS (ON)MAX. 250µSEC. PULSE TEST @